<div dir="ltr">Apparently this did not make it to the list. Guess this is because my list membership was not approved yet then.<br><div class="gmail_extra"><br><div class="gmail_quote">2015-01-25 11:30 GMT+01:00 Frans Meulenbroeks <span dir="ltr"><<a href="mailto:fransmeulenbroeks@gmail.com" target="_blank">fransmeulenbroeks@gmail.com</a>></span>:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div><div><div><div><div><div><div><div><div><div><div><div><div><div><div>Hi,<br><br></div>I was trying to see which of the ARM boards I had lying around would boot FC21.<br></div>I followed these instructions:<br><br><a href="http://fedoraproject.org/wiki/Architectures/ARM/F21/Installation" target="_blank">http://fedoraproject.org/wiki/Architectures/ARM/F21/Installation</a><br><br></div>With these I managed to boot FC21 successfully on<br></div>- orange pi (A20, similar to banana pi)<br></div>- pandaboard<br></div>- beaglebone white<br><br></div>However, although according to the instructions the same MLO and u-boot are to be used for beaglebone black, it does not boot there, although the very same card works with beaglebone white.<br></div>I have added a serial port to the BBB and captured the boot log. See at the end of this message.<br></div>Anyone an idea what is wrong?<br><br></div>While at it: <br></div>According to <a href="http://fedoraproject.org/wiki/Architectures/ARM/F21/Installation/Hardware_Status" target="_blank">http://fedoraproject.org/wiki/Architectures/ARM/F21/Installation/Hardware_Status</a> beagleboard XM also works but there is no u-boot data in the image for XM. Suggestions for this?<br><br></div>And I noticed the u-boot dir also contains a u-boot for the Mele A1000. I wanted to try that one the A2000 which is identical hw, but it did not work (and I do not have serial for the A2000)<br></div>Anyone a suggestion.<br><br></div>I also noticed beagleboard being in the uboot folder but it was not listed on the pages referred to above, Should this work?<br><br></div>Lastly I noticed in the image a boot.scr and a boot.cmd file (slightly different).<br>These seem to be some generic code to boot into a number of boards, but I could not find instructions how to use/invoke this. Is that going to be useful for me? How should I use it?<br><br>Thanks, Frans<br><div><div><div><div><br></div><div>PS: subscription to the list is pending approval, please also reply directly. Thanks.<br><br></div><div>---- boot log from beaglebone black ----<br></div><div><div><div><div><div><div><br>U-Boot SPL 2013.04-dirty (May 06 2013 - 16:12:47)<br>musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)<br>musb-hdrc: MHDRC RTL version 2.0 <br>musb-hdrc: setup fifo_mode 4<br>musb-hdrc: 28/31 max ep, 16384/16384 memory<br>USB Peripheral mode controller at 47401000 using PIO, IRQ 0<br>musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)<br>musb-hdrc: MHDRC RTL version 2.0 <br>musb-hdrc: setup fifo_mode 4<br>musb-hdrc: 28/31 max ep, 16384/16384 memory<br>USB Host mode controller at 47401800 using PIO, IRQ 0<br>OMAP SD/MMC: 0<br>mmc_send_cmd : timeout: No status update<br>reading u-boot.img<br>reading u-boot.img<br><br><br>U-Boot 2013.04-dirty (May 06 2013 - 16:12:47)<br><br>I2C: ready<br>DRAM: 512 MiB<br>WARNING: Caches not enabled<br>NAND: No NAND device found!!!<br>0 MiB<br>MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1<br>*** Warning - readenv() failed, using default environment<br><br>musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)<br>musb-hdrc: MHDRC RTL version 2.0 <br>musb-hdrc: setup fifo_mode 4<br>musb-hdrc: 28/31 max ep, 16384/16384 memory<br>USB Peripheral mode controller at 47401000 using PIO, IRQ 0<br>musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)<br>musb-hdrc: MHDRC RTL version 2.0 <br>musb-hdrc: setup fifo_mode 4<br>musb-hdrc: 28/31 max ep, 16384/16384 memory<br>USB Host mode controller at 47401800 using PIO, IRQ 0<br>Net: <ethaddr> not set. Validating first E-fuse MAC<br>cpsw, usb_ether<br>Hit any key to stop autoboot: 0 <br>gpio: pin 53 (gpio 53) value is 1<br>mmc0 is current device<br>micro SD card found<br>mmc0 is current device<br>gpio: pin 54 (gpio 54) value is 1<br>SD/MMC found on device 0<br>** File not found uEnv.txt **<br>gpio: pin 55 (gpio 55) value is 1<br>Failed to mount ext2 filesystem...<br>** Unrecognized filesystem type **<br><br><br></div></div></div></div></div></div></div></div></div></div>
</blockquote></div><br></div></div>