Installing Fedora 16 Release on Intellistation 9111-285 headless...
Link
link.charge at googlemail.com
Sun Dec 25 22:44:00 UTC 2011
Hih0 list,
1. Startup your Intellistation, and wait for the banner full of IBM
chars. Configure the boot order to use the internal DVD drive first.
2. To access the 'Advanced System Management' WebGUI of your HMC via https://
(which is mandatory),
the following SSL method must be allowed in your web browser. Under
the built-in URL 'about:config' of Firefox, set:
security.ssl3.rsa_rc4_40_md5;true.
The standard passwords to access the WebGUI (after resetting the HMC)
are: admin/admin or general/general (User/Password).
3. Depending on your current OFW state, it could be necessary to reset
the NVRAM via the menu option:
System Service Aids -> Factory Configuration -> Firmware.
This will reset the OFW variable 'real-base' to C0000, which saves you
a crash shortly after the message 'returnung from prom_init'
when trying to boot from the Fedora DVD.
4. When the yaboot prompt appears, enter linux vnc
vncpassword=123456789 to start. Note: Usually, the first char is
sucked away, watch your typing.
5. With a GXT6500P or similar graphics board installed, we are now
blind and have to tell some things to the installer in the following
order:
- after the screen went off (no sync), wait for the DVD to load some
data for a few minutes (the DVD will be accessed 2 short times at
least when finished).
- enter '1' and hit return. This results in a short access to the DVD.
- enter '1' and hit return again. After that the DVD loads for approx.
7 minutes, Wait for the drive to finish while the LED is on.
- After 1 minute there will be a short sound from the drive. Enter '1'
and press return for the last time, this will open the VNC server on
remote side.
6. With the 'nmap' utility the DHCP assigned interface of port T5 will
read '5901/tcp open vnc-1' and '6001/tcp open X11:1' now.
Connect your VNC viewer to the IP address assigned by your DHCP
server, port 5901 and password 123456789 (as told at yaboot prompt).
7. Reboot the machine via the WebGUI after the installation. Do some
updates and 'write bugs'.
P.S.
Would be cool if someone can incorporate the GXT6500P patch from CRUX
PPC to have some blazzering fast display (or display at all löl :)
pP.S.
here is a dmesg right after b00ting the fresh installation for the
first time:
[root at power ~]# dmesg
[ 0.000000] Phyp-dump not supported on this hardware
[ 0.000000] Allocated 1966080 bytes for 1024 pacas at
c0000000073c0000
[ 0.000000] Using pSeries machine description
[ 0.000000] Page orders: linear mapping = 24, virtual = 16, io =
12, vmemmap = 24
[ 0.000000] Using 1TB segments
[ 0.000000] Found initrd at 0xc000000003400000:0xc000000004651c00
[ 0.000000] bootconsole [udbg0] enabled
[ 0.000000] Partition configured for 2 cpus.
[ 0.000000] CPU maps initialized for 2 threads per core
[ 0.000000] (thread shift is 1)
[ 0.000000] Freed 1900544 bytes for unused pacas
[ 0.000000] Starting Linux PPC64 #1 SMP Tue Dec 20 21:24:05 UTC 2011
[ 0.000000] -----------------------------------------------------
[ 0.000000] ppc64_pft_size = 0x1a
[ 0.000000] physicalMemorySize = 0xf5000000
[ 0.000000] htab_hash_mask = 0x7ffff
[ 0.000000] -----------------------------------------------------
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.1.5-6.fc16.ppc64 (mockbuild at ppc07.qa.fedoraproject.org
) (gcc version 4.6.2 20111027 (Red Hat 4.6.2-1) (GCC) ) #1 SMP Tue Dec
20 21:24:05 UTC 2011
[ 0.000000] [boot]0012 Setup Arch
[ 0.000000] Node 0 Memory: 0x0-0xf5000000
[ 0.000000] PCI host bridge /pci at 800000020000002 ranges:
[ 0.000000] IO 0x000003fe00200000..0x000003fe002fffff ->
0x0000000000000000
[ 0.000000] MEM 0x0000040040000000..0x000004007fffffff ->
0x00000000c0000000
[ 0.000000] PCI host bridge /pci at 800000020000003 ranges:
[ 0.000000] IO 0x000003fe00300000..0x000003fe003fffff ->
0x0000000000000000
[ 0.000000] MEM 0x0000040080000000..0x00000400bfffffff ->
0x00000000c0000000
[ 0.000000] PCI host bridge /pci at 800000020000004 ranges:
[ 0.000000] IO 0x000003fe00400000..0x000003fe004fffff ->
0x0000000000000000
[ 0.000000] MEM 0x00000400c0000000..0x00000400ffffffff ->
0x00000000c0000000
[ 0.000000] EEH: PCI Enhanced I/O Error Handling Enabled
[ 0.000000] PPC64 nvram contains 7168 bytes
[ 0.000000] Using dedicated idle loop
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x0000f500
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000f500
[ 0.000000] On node 0 totalpages: 62720
[ 0.000000] DMA zone: 54 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 62666 pages, LIFO batch:1
[ 0.000000] [boot]0015 Setup Done
[ 0.000000] PERCPU: Embedded 2 pages/cpu @c000000001800000 s84224
r0 d46848 u524288
[ 0.000000] pcpu-alloc: s84224 r0 d46848 u524288 alloc=1*1048576
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on.
Total pages: 62666
[ 0.000000] Policy zone: DMA
[ 0.000000] Kernel command line: root=/dev/mapper/vg_power-lv_root
ro rd.md=0 rd.dm=0 rhgb KEYTABLE=de quiet SYSFONT=True rd.luks=0
rd.lvm.lv=vg_power/lv_swap rd.lvm.lv=vg_power/lv_root LANG=en_US.UTF-8
[ 0.000000] PID hash table entries: 4096 (order: -1, 32768 bytes)
[ 0.000000] freeing bootmem node 0
[ 0.000000] Memory: 3942528k/4014080k available (19456k kernel
code, 71552k reserved, 1984k data, 2762k bss, 6912k init)
[ 0.000000] SLUB: Genslabs=19, HWalign=128, Order=0-3,
MinObjects=0, CPUs=2, Nodes=256
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] pic: no ISA interrupt controller
[ 0.000000] time_init: decrementer frequency = 262.400000 MHz
[ 0.000000] time_init: processor frequency = 2096.901000 MHz
[ 0.000000] clocksource: timebase mult[f3e706] shift[22] registered
[ 0.000000] clockevent: decrementer mult[432ca57a] shift[32] cpu[0]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.000000] allocated 2007040 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't
want memory cgroups
[ 0.000517] pid_max: default: 32768 minimum: 301
[ 0.000555] Security Framework initialized
[ 0.000565] SELinux: Initializing.
[ 0.000572] SELinux: Starting in permissive mode
[ 0.000726] Dentry cache hash table entries: 524288 (order: 6,
4194304 bytes)
[ 0.002084] Inode-cache hash table entries: 262144 (order: 5,
2097152 bytes)
[ 0.002625] Mount-cache hash table entries: 4096
[ 0.009502] Initializing cgroup subsys cpuacct
[ 0.009510] Initializing cgroup subsys memory
[ 0.009619] Initializing cgroup subsys devices
[ 0.009623] Initializing cgroup subsys freezer
[ 0.009626] Initializing cgroup subsys net_cls
[ 0.009630] Initializing cgroup subsys blkio
[ 0.009635] Initializing cgroup subsys perf_event
[ 0.009686] ftrace: allocating 21643 entries in 8 pages
[ 0.013478] POWER5+/++ performance monitor hardware support
registered
[ 0.014237] Brought up 2 CPUs
[ 0.014244] Node 0 CPUs: 0-1
[ 0.015324] devtmpfs: initialized
[ 0.024902] atomic64 test passed
[ 0.024964] NET: Registered protocol family 16
[ 0.024979] IBM eBus Device Driver
[ 0.028435] PCI: Probing PCI hardware
[ 0.029484] pci 0000:00:01.0: supports D1 D2
[ 0.030689] IOMMU table initialized, virtual merging enabled
[ 0.038647] pci 0001:cc:01.0: supports D1
[ 0.042918] pci 0001:c8:01.0: supports D1 D2
[ 0.042922] pci 0001:c8:01.0: PME# supported from D0 D1 D2 D3hot
[ 0.043059] pci 0001:c8:01.0: PME# disabled
[ 0.052126] pci 0002:cc:01.0: supports D1 D2
[ 0.052130] pci 0002:cc:01.0: PME# supported from D0 D1 D2 D3hot
[ 0.052272] pci 0002:cc:01.0: PME# disabled
[ 0.053478] pci 0002:cc:01.1: supports D1 D2
[ 0.053482] pci 0002:cc:01.1: PME# supported from D0 D1 D2 D3hot
[ 0.053628] pci 0002:cc:01.1: PME# disabled
[ 0.054840] pci 0002:cc:01.2: supports D1 D2
[ 0.054843] pci 0002:cc:01.2: PME# supported from D0 D1 D2 D3hot
[ 0.054984] pci 0002:cc:01.2: PME# disabled
[ 0.057428] pci 0002:d0:01.0: PME# supported from D0 D3hot D3cold
[ 0.057570] pci 0002:d0:01.0: PME# disabled
[ 0.059513] pci 0002:d0:01.1: PME# supported from D0 D3hot D3cold
[ 0.059655] pci 0002:d0:01.1: PME# disabled
[ 0.064409] PCI: Probing PCI hardware done
[ 0.065888] bio: create slab <bio-0> at 0
[ 0.066222] vgaarb: device added: PCI:0000:00:01.0,decodes=io
+mem,owns=mem,locks=none
[ 0.066247] vgaarb: loaded
[ 0.066249] vgaarb: bridge control possible 0000:00:01.0
[ 0.066336] SCSI subsystem initialized
[ 0.066401] libata version 3.00 loaded.
[ 0.066480] usbcore: registered new interface driver usbfs
[ 0.066501] usbcore: registered new interface driver hub
[ 0.066548] usbcore: registered new device driver usb
[ 0.066792] NetLabel: Initializing
[ 0.066795] NetLabel: domain hash size = 128
[ 0.066797] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.066812] NetLabel: unlabeled traffic allowed by default
[ 0.066878] Switching to clocksource timebase
[ 0.073450] Switched to NOHz mode on CPU #0
[ 0.074266] Switched to NOHz mode on CPU #1
[ 0.083218] NET: Registered protocol family 2
[ 0.083263] IP route cache hash table entries: 32768 (order: 2,
262144 bytes)
[ 0.083420] TCP established hash table entries: 131072 (order: 5,
2097152 bytes)
[ 0.083831] TCP bind hash table entries: 65536 (order: 4, 1048576
bytes)
[ 0.084056] TCP: Hash tables configured (established 131072 bind
65536)
[ 0.084060] TCP reno registered
[ 0.084066] UDP hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.084087] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes)
[ 0.084168] NET: Registered protocol family 1
[ 0.085475] PCI: CLS 128 bytes, default 128
[ 0.085533] Unpacking initramfs...
[ 0.609657] Freeing initrd memory: 18816k freed
[ 0.610105] RTAS daemon started
[ 0.610894] RTAS: event: 27, Type: Platform Error, Severity: 2
[ 0.611027] vio 30000000: Warning: IOMMU dma not supported: mask
0xffffffffffffffff, table unavailable
[ 0.611077] vio 30000001: Warning: IOMMU dma not supported: mask
0xffffffffffffffff, table unavailable
[ 0.611103] vio 4000: Warning: IOMMU dma not supported: mask
0xffffffffffffffff, table unavailable
[ 0.611125] vio 4001: Warning: IOMMU dma not supported: mask
0xffffffffffffffff, table unavailable
[ 0.611148] vio 4002: Warning: IOMMU dma not supported: mask
0xffffffffffffffff, table unavailable
[ 0.611171] vio 4003: Warning: IOMMU dma not supported: mask
0xffffffffffffffff, table unavailable
[ 0.611544] audit: initializing netlink socket (disabled)
[ 0.611561] type=2000 audit(1324787571.599:1): initialized
[ 0.755756] HugeTLB registered 16 MB page size, pre-allocated 0 pages
[ 0.755760] HugeTLB registered 16 GB page size, pre-allocated 0 pages
[ 0.758822] VFS: Disk quotas dquot_6.5.2
[ 0.758904] Dquot-cache hash table entries: 8192 (order 0, 65536
bytes)
[ 0.759620] msgmni has been set to 7736
[ 0.759729] SELinux: Registering netfilter hooks
[ 0.760270] alg: No test for stdrng (krng)
[ 0.760284] NET: Registered protocol family 38
[ 0.760366] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 253)
[ 0.760407] io scheduler noop registered
[ 0.760412] io scheduler deadline registered
[ 0.760482] io scheduler cfq registered (default)
[ 0.760615] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.760631] pciehp: PCI Express Hot Plug Controller Driver version:
0.4
[ 0.760757] Using unsupported 1024x768 display at 4007dfa0000,
depth=8, pitch=1
[ 0.760887] Console: switching to colour frame buffer device 128x48
[ 0.811539] fb0: Open Firmware frame buffer device on /
pci at 800000020000002/display at 1
[ 0.811663] vio_register_driver: driver hvc_console registering
[ 0.812139] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.908097] TX39/49 Serial driver version 1.11
[ 0.908290] Linux agpgart interface v0.103
[ 0.909506] loop: module loaded
[ 0.909568] Uniform Multi-Platform E-IDE driver
[ 0.909614] ide-gd driver 1.18
[ 0.909784] Fixed MDIO Bus: probed
[ 0.909870] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[ 0.910147] ehci_hcd 0002:cc:01.2: EHCI Host Controller
[ 0.910243] ehci_hcd 0002:cc:01.2: new USB bus registered, assigned
bus number 1
[ 0.936974] ehci_hcd 0002:cc:01.2: irq 276, io mem 0x400f8002000
[ 0.956921] ehci_hcd 0002:cc:01.2: USB 2.0 started, EHCI 1.00
[ 0.956956] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002
[ 0.956961] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 0.956966] usb usb1: Product: EHCI Host Controller
[ 0.956969] usb usb1: Manufacturer: Linux 3.1.5-6.fc16.ppc64 ehci_hcd
[ 0.956973] usb usb1: SerialNumber: 0002:cc:01.2
[ 0.957153] hub 1-0:1.0: USB hub found
[ 0.957159] hub 1-0:1.0: 5 ports detected
[ 0.957317] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.957500] ohci_hcd 0002:cc:01.0: OHCI Host Controller
[ 0.957582] ohci_hcd 0002:cc:01.0: new USB bus registered, assigned
bus number 2
[ 0.957615] ohci_hcd 0002:cc:01.0: irq 276, io mem 0x400f8001000
[ 1.046899] usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
[ 1.046903] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.046907] usb usb2: Product: OHCI Host Controller
[ 1.046910] usb usb2: Manufacturer: Linux 3.1.5-6.fc16.ppc64 ohci_hcd
[ 1.046914] usb usb2: SerialNumber: 0002:cc:01.0
[ 1.047071] hub 2-0:1.0: USB hub found
[ 1.047080] hub 2-0:1.0: 3 ports detected
[ 1.047323] ohci_hcd 0002:cc:01.1: OHCI Host Controller
[ 1.047397] ohci_hcd 0002:cc:01.1: new USB bus registered, assigned
bus number 3
[ 1.047426] ohci_hcd 0002:cc:01.1: irq 276, io mem 0x400f8000000
[ 1.136896] usb usb3: New USB device found, idVendor=1d6b,
idProduct=0001
[ 1.136903] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.136907] usb usb3: Product: OHCI Host Controller
[ 1.136910] usb usb3: Manufacturer: Linux 3.1.5-6.fc16.ppc64 ohci_hcd
[ 1.136914] usb usb3: SerialNumber: 0002:cc:01.1
[ 1.137072] hub 3-0:1.0: USB hub found
[ 1.137080] hub 3-0:1.0: 2 ports detected
[ 1.137169] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.137258] usbcore: registered new interface driver usbserial
[ 1.137270] USB Serial support registered for generic
[ 1.137288] usbcore: registered new interface driver
usbserial_generic
[ 1.137290] usbserial: USB Serial Driver core
[ 1.137496] mousedev: PS/2 mouse device common for all mice
[ 1.137731] rtc-generic rtc-generic: rtc core: registered rtc-
generic as rtc0
[ 1.137890] device-mapper: uevent: version 1.0.3
[ 1.138011] device-mapper: ioctl: 4.21.0-ioctl (2011-07-06)
initialised: dm-devel at redhat.com
[ 1.138360] usbcore: registered new interface driver usbhid
[ 1.138363] usbhid: USB HID core driver
[ 1.138430] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.138447] TCP cubic registered
[ 1.138450] Initializing XFRM netlink socket
[ 1.138630] NET: Registered protocol family 10
[ 1.138822] Mobile IPv6
[ 1.138826] NET: Registered protocol family 17
[ 1.138846] Registering the dns_resolver key type
[ 1.138863] Running MSI bitmap self-tests ...
[ 1.140627] PM: Hibernation image not present or could not be loaded.
[ 1.140645] registered taskstats version 1
[ 1.140816] Call Trace:
[ 1.140823] [c0000000f1943600] [c000000000017e14] .show_stack
+0xb4/0x1d0 (unreliable)
[ 1.140830] [c0000000f19436c0] [c00000000081791c] .dump_stack
+0x28/0x3c
[ 1.140836] [c0000000f1943740]
[c00000000007edbc] .eeh_dn_check_failure+0x30c/0x370
[ 1.140842] [c0000000f1943800] [c00000000002ed0c] .rtas_read_config
+0x15c/0x1b0
[ 1.140847] [c0000000f19438b0]
[c00000000002ee1c] .rtas_pci_read_config+0xbc/0xf0
[ 1.140854] [c0000000f1943960]
[c000000000425a38] .pci_bus_read_config_word+0xb8/0x120
[ 1.140860] [c0000000f1943a30]
[c000000000429d58] .__pci_bus_find_cap_start+0x48/0x90
[ 1.140866] [c0000000f1943ae0]
[c00000000042a2bc] .pci_find_capability+0x3c/0x90
[ 1.140872] [c0000000f1943b80] [c00000000042ad0c] .pci_dev_reset
+0x2ec/0x520
[ 1.140877] [c0000000f1943c40]
[c00000000042f1ec] .pci_probe_reset_function+0x2c/0x40
[ 1.140883] [c0000000f1943cd0]
[c000000000435e0c] .pci_create_sysfs_dev_files+0x37c/0x4a0
[ 1.140889] [c0000000f1943d90] [c000000000c861e0] .pci_sysfs_init
+0x3c/0x9c
[ 1.140895] [c0000000f1943e20] [c00000000000aad0] .do_one_initcall
+0x70/0x1f0
[ 1.140901] [c0000000f1943ee0] [c000000000c40c3c] .kernel_init
+0x15c/0x1e8
[ 1.140907] [c0000000f1943f90] [c000000000026d58] .kernel_thread
+0x54/0x70
[ 1.145195] rtc-generic rtc-generic: setting system clock to
2011-12-25 04:32:52 UTC (1324787572)
[ 1.145210] Initializing network drop monitor service
[ 1.145257] EEH: Detected PCI bus error on device <null>
[ 1.145261] EEH: This PCI device has failed 1 times in the last hour:
[ 1.145265] EEH: Bus location=U787F.001.DPM232N-P1-C4-T1 driver=
pci addr=0000:00:01.0
[ 1.145270] EEH: Device location=U787F.001.DPM232N-P1-C4-T1 driver=
pci addr=<null>
[ 1.146466] EEH: of node=/pci at 800000020000002/display at 1
[ 1.146515] EEH: PCI device/vendor: 021b1014
[ 1.146563] EEH: PCI cmd/status register: 02b00146
[ 1.148317] RTAS: event: 28, Type: Platform Error, Severity: 2
[ 1.148452] Freeing unused kernel memory: 6912k freed
[ 1.317570] dracut: dracut-013-20.fc16
[ 1.328206] dracut: rd.luks=0: removing cryptoluks activation
[ 1.339667] udevd[96]: starting version 173
[ 1.519299] dracut: Starting plymouth daemon
[ 1.576917] dracut: rd.dm=0: removing DM RAID activation
[ 1.584544] dracut: rd.md=0: removing MD RAID activation
[ 1.645128] pata_pdc2027x 0001:cc:01.0: version 1.0
[ 1.645281] pata_pdc2027x 0001:cc:01.0: enabling device (0002 ->
0003)
[ 1.671271] ipr: IBM Power RAID SCSI Device Driver version: 2.5.2
(April 27, 2011)
[ 1.671423] ipr 0001:d0:01.0: Found IOA with IRQ: 325
[ 1.745287] pata_pdc2027x 0001:cc:01.0: PLL input clock 32750 kHz
[ 1.762311] ipr 0001:d0:01.0: Starting IOA initialization sequence.
[ 1.767238] ipr 0001:d0:01.0: Adapter firmware version: 0510006D
[ 1.775966] scsi1 : pata_pdc2027x
[ 1.776140] scsi2 : pata_pdc2027x
[ 1.776219] ata1: PATA max UDMA/133 mmio m16384 at 0x400b8000000 cmd
0x400b80017c0 irq 324
[ 1.776226] ata2: PATA max UDMA/133 mmio m16384 at 0x400b8000000 cmd
0x400b80015c0 irq 324
[ 1.781532] ipr 0001:d0:01.0: IOA initialized.
[ 1.781548] scsi0 : IBM 573E Storage Adapter
[ 1.798634] scsi 0:0:8:0: Direct-Access IBM H0
HUS103073FL3800 RPQR PQ: 0 ANSI: 4
[ 1.805455] scsi 0:0:15:0: Enclosure IBM VSBPD4E1
U4SCSI 1203 PQ: 0 ANSI: 2
[ 1.947514] ata1.00: ATAPI: IBM DROM00205L1 H0, P533, max
UDMA/66
[ 1.987398] ata1.00: configured for UDMA/66
[ 1.988584] scsi: waiting for bus probes to complete ...
[ 2.044533] sd 0:0:8:0: Attached scsi generic sg0 type 0
[ 2.044843] scsi 0:0:15:0: Attached scsi generic sg1 type 13
[ 2.046032] sd 0:0:8:0: [sda] 143374000 512-byte logical blocks:
(73.4 GB/68.3 GiB)
[ 2.047167] scsi 1:0:0:0: CD-ROM IBM DROM00205L1
H0 P533 PQ: 0 ANSI: 2
[ 2.048753] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 2.048759] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.048948] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.049055] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 2.065110] sd 0:0:8:0: [sda] Write Protect is off
[ 2.065117] sd 0:0:8:0: [sda] Mode Sense: d3 00 10 08
[ 2.070591] sd 0:0:8:0: [sda] Write cache: disabled, read cache:
enabled, supports DPO and FUA
[ 2.099669] sda: sda1 sda2 sda3
[ 2.127937] sd 0:0:8:0: [sda] Attached SCSI disk
[ 2.162511] scsi: unknown device type 31
[ 2.162517] scsi 0:255:255:255: No Device IBM
573E001 0150 PQ: 0 ANSI: 0
[ 2.162716] scsi 0:255:255:255: Attached scsi generic sg3 type 31
[ 2.276917] usb 2-1: new full speed USB device number 2 using
ohci_hcd
[ 2.503929] usb 2-1: New USB device found, idVendor=05ac,
idProduct=1002
[ 2.503933] usb 2-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 2.503937] usb 2-1: Product: Hub in Apple Extended USB Keyboard
[ 2.503941] usb 2-1: Manufacturer: Alps Electric
[ 2.507001] hub 2-1:1.0: USB hub found
[ 2.509927] hub 2-1:1.0: 3 ports detected
[ 2.586184] dracut: Scanning devices sda3 for LVM logical volumes
vg_power/lv_swap vg_power/lv_root
[ 2.670981] dracut: inactive '/dev/vg_power/lv_swap' [5.78 GiB]
inherit
[ 2.671131] dracut: inactive '/dev/vg_power/lv_home' [20.69 GiB]
inherit
[ 2.671288] dracut: inactive '/dev/vg_power/lv_root' [41.38 GiB]
inherit
[ 2.808927] usb 2-1.1: new full speed USB device number 3 using
ohci_hcd
[ 2.933921] usb 2-1.1: New USB device found, idVendor=05ac,
idProduct=0205
[ 2.933926] usb 2-1.1: New USB device strings: Mfr=1, Product=3,
SerialNumber=0
[ 2.933931] usb 2-1.1: Product: Apple Extended USB Keyboard
[ 2.933939] usb 2-1.1: Manufacturer: Alps Electric
[ 2.943145] input: Alps Electric Apple Extended USB Keyboard as /
devices/pci0002:00/0002:00:02.3/0002:cc:01.0/usb2/2-1/2-1.1/2-1.1:1.0/
input/input0
[ 2.943319] generic-usb 0003:05AC:0205.0001: input,hidraw0: USB HID
v1.10 Keyboard [Alps Electric Apple Extended USB Keyboard] on
usb-0002:cc:01.0-1.1/input0
[ 2.953023] input: Alps Electric Apple Extended USB Keyboard as /
devices/pci0002:00/0002:00:02.3/0002:cc:01.0/usb2/2-1/2-1.1/2-1.1:1.1/
input/input1
[ 2.953160] generic-usb 0003:05AC:0205.0002: input,hidraw1: USB HID
v1.10 Device [Alps Electric Apple Extended USB Keyboard] on
usb-0002:cc:01.0-1.1/input1
[ 3.037673] EXT4-fs (dm-1): INFO: recovery required on readonly
filesystem
[ 3.037678] EXT4-fs (dm-1): write access will be enabled during
recovery
[ 3.038924] usb 2-1.3: new low speed USB device number 4 using
ohci_hcd
[ 3.165920] usb 2-1.3: New USB device found, idVendor=046d,
idProduct=c046
[ 3.165926] usb 2-1.3: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 3.165930] usb 2-1.3: Product: USB Optical Mouse
[ 3.165935] usb 2-1.3: Manufacturer: Logitech
[ 3.177077] input: Logitech USB Optical Mouse as /devices/
pci0002:00/0002:00:02.3/0002:cc:01.0/usb2/2-1/2-1.3/2-1.3:1.0/input/
input2
[ 3.177279] generic-usb 0003:046D:C046.0003: input,hidraw2: USB HID
v1.10 Mouse [Logitech USB Optical Mouse] on usb-0002:cc:01.0-1.3/input0
[ 3.217002] EEH: bus reset 1 failed on slot /pci at 800000020000002/
display at 1, rc=2
[ 4.276114] EXT4-fs (dm-1): orphan cleanup on readonly fs
[ 4.276124] EXT4-fs (dm-1): ext4_orphan_cleanup: deleting
unreferenced inode 393218
[ 4.276199] EXT4-fs (dm-1): 1 orphan inode deleted
[ 4.276203] EXT4-fs (dm-1): recovery complete
[ 4.329430] EXT4-fs (dm-1): mounted filesystem with ordered data
mode. Opts: (null)
[ 4.421604] dracut: Checking ext4: /dev/mapper/vg_power-lv_root
[ 4.421674] dracut: issuing e2fsck -a /dev/mapper/vg_power-lv_root
[ 4.475101] dracut: /dev/mapper/vg_power-lv_root: clean,
124045/2711552 files, 1078520/10846208 blocks
[ 4.475313] dracut: Remounting /dev/mapper/vg_power-lv_root with -o
ro
[ 4.509272] EXT4-fs (dm-1): mounted filesystem with ordered data
mode. Opts: (null)
[ 4.521722] dracut: Mounted root filesystem /dev/mapper/vg_power-
lv_root
[ 4.872324] dracut: Switching root
[ 5.287000] EEH: bus reset 2 failed on slot /pci at 800000020000002/
display at 1, rc=2
[ 5.329827] type=1404 audit(1324787576.679:2): enforcing=1
old_enforcing=0 auid=4294967295 ses=4294967295
[ 5.487975] SELinux: 2048 avtab hash slots, 97124 rules.
[ 5.516335] SELinux: 2048 avtab hash slots, 97124 rules.
[ 5.624496] SELinux: 9 users, 13 roles, 3910 types, 208 bools, 1
sens, 1024 cats
[ 5.624501] SELinux: 82 classes, 97124 rules
[ 5.631460] SELinux: Completing initialization.
[ 5.631463] SELinux: Setting up existing superblocks.
[ 5.631474] SELinux: initialized (dev sysfs, type sysfs), uses
genfs_contexts
[ 5.631481] SELinux: initialized (dev rootfs, type rootfs), uses
genfs_contexts
[ 5.632406] SELinux: initialized (dev bdev, type bdev), uses
genfs_contexts
[ 5.632414] SELinux: initialized (dev proc, type proc), uses
genfs_contexts
[ 5.632426] SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
[ 5.632439] SELinux: initialized (dev devtmpfs, type devtmpfs),
uses transition SIDs
[ 5.633328] SELinux: initialized (dev sockfs, type sockfs), uses
task SIDs
[ 5.633335] SELinux: initialized (dev debugfs, type debugfs), uses
genfs_contexts
[ 5.635837] SELinux: initialized (dev pipefs, type pipefs), uses
task SIDs
[ 5.635846] SELinux: initialized (dev anon_inodefs, type
anon_inodefs), uses genfs_contexts
[ 5.635853] SELinux: initialized (dev devpts, type devpts), uses
transition SIDs
[ 5.635870] SELinux: initialized (dev hugetlbfs, type hugetlbfs),
uses transition SIDs
[ 5.635880] SELinux: initialized (dev mqueue, type mqueue), uses
transition SIDs
[ 5.635889] SELinux: initialized (dev selinuxfs, type selinuxfs),
uses genfs_contexts
[ 5.635927] SELinux: initialized (dev usbfs, type usbfs), uses
genfs_contexts
[ 5.635939] SELinux: initialized (dev sysfs, type sysfs), uses
genfs_contexts
[ 5.636818] SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
[ 5.636825] SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
[ 5.641262] SELinux: initialized (dev dm-1, type ext4), uses xattr
[ 5.649646] type=1403 audit(1324787576.999:3): policy loaded
auid=4294967295 ses=4294967295
[ 5.664153] systemd[1]: Successfully loaded SELinux policy in 372ms
257us.
[ 5.726056] systemd[1]: Successfully loaded SELinux database in
61ms 528us, size on heap is 477K.
[ 5.754047] SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
[ 5.755960] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 5.827599] systemd[1]: Relabelled /dev and /run in 71ms 511us.
[ 5.843193] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 5.896945] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 5.936979] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 5.966971] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 6.016947] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 6.041360] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 6.086971] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 6.116964] SELinux: initialized (dev cgroup, type cgroup), uses
genfs_contexts
[ 6.117109] systemd[1]: systemd 37 running in system mode. (+PAM
+LIBWRAP +AUDIT +SELINUX +SYSVINIT +LIBCRYPTSETUP; fedora)
[ 6.149338] systemd[1]: Set hostname to <power.charge.homeunix.net>.
[ 7.219547] SELinux: initialized (dev autofs, type autofs), uses
genfs_contexts
[ 7.357016] EEH: bus reset 3 failed on slot /pci at 800000020000002/
display at 1, rc=2
[ 7.357020] EEH: Unable to reset, rc=-1
[ 7.357024] EEH: Unable to recover from failure of PCI device at
location=U787F.001.DPM232N-P1-C4-T1 driver= pci addr=<null>
[ 7.357027] Please try reseating this device or replacing it.
[ 7.358149] EEH: of node=/pci at 800000020000002/display at 1
[ 7.358198] EEH: PCI device/vendor: 021b1014
[ 7.358247] EEH: PCI cmd/status register: 02b00140
[ 7.358249] EEH: no PCI device for this of node
[ 7.359487] RTAS: event: 29, Type: Platform Error, Severity: 2
[ 7.486564] SELinux: initialized (dev tmpfs, type tmpfs), uses
transition SIDs
[ 7.568825] SELinux: initialized (dev securityfs, type securityfs),
uses genfs_contexts
[ 7.649016] SELinux: initialized (dev hugetlbfs, type hugetlbfs),
uses transition SIDs
[ 8.116929] RPC: Registered named UNIX socket transport module.
[ 8.116934] RPC: Registered udp transport module.
[ 8.116937] RPC: Registered tcp transport module.
[ 8.116940] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 8.117164] SELinux: initialized (dev rpc_pipefs, type rpc_pipefs),
uses genfs_contexts
[ 8.296491] udevd[406]: starting version 173
[ 8.817688] EXT4-fs (dm-1): re-mounted. Opts: (null)
[ 8.878814] SELinux: initialized (dev configfs, type configfs),
uses genfs_contexts
[ 9.109206] e1000: Intel(R) PRO/1000 Network Driver - version
7.3.21-k8-NAPI
[ 9.109211] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 9.109403] e1000 0002:d0:01.0: enabling device (0000 -> 0002)
[ 9.218073] ttyn0 at MMIO 0x0 (irq = 275) is a jsm
[ 9.446851] e1000 0002:d0:01.0: eth0: (PCI-X:133MHz:64-bit)
00:14:5e:96:c6:ea
[ 9.446865] e1000 0002:d0:01.0: eth0: Intel(R) PRO/1000 Network
Connection
[ 9.447081] e1000 0002:d0:01.1: enabling device (0000 -> 0002)
[ 9.447419] jsm: Port 0 added
[ 9.447425] ttyn1 at MMIO 0x0 (irq = 275) is a jsm
[ 9.518172] jsm: Port 1 added
[ 9.518178] jsm 0002:c8:01.0: board 1: Digi Neo (rev 2), irq 275
[ 9.787194] e1000 0002:d0:01.1: eth1: (PCI-X:133MHz:64-bit)
00:14:5e:96:c6:eb
[ 9.787203] e1000 0002:d0:01.1: eth1: Intel(R) PRO/1000 Network
Connection
[ 10.019571] scsi 0:0:15:0: Resetting device
[ 10.265177] ses 0:0:15:0: Attached Enclosure device
[ 10.344722] systemd-vconsole-setup[476]: Cannot open font file True
[ 10.618435] mtp-probe[507]: checking bus 2, device 3: "/sys/devices/
pci0002:00/0002:00:02.3/0002:cc:01.0/usb2/2-1/2-1.1"
[ 10.618655] mtp-probe[506]: checking bus 2, device 4: "/sys/devices/
pci0002:00/0002:00:02.3/0002:cc:01.0/usb2/2-1/2-1.3"
[ 10.636764] systemd-vconsole-setup[476]: /bin/setfont failed with
error code 66.
[ 10.703699] Adding 6062016k swap on /dev/mapper/vg_power-lv_swap.
Priority:0 extents:1 across:6062016k
[ 10.798412] mtp-probe[506]: bus: 2, device: 4 was not an MTP device
[ 10.798426] mtp-probe[507]: bus: 2, device: 3 was not an MTP device
[ 10.917023] snd_cs4281 0001:c8:01.0: Refused to change power state,
currently in D1
[ 11.119482] systemd-fsck[598]: /dev/sda2: recovering journal
[ 11.244167] systemd-fsck[598]: /dev/sda2: clean, 21/128016 files,
70608/512000 blocks
[ 11.311694] rmmod[609]: ERROR: Module scsi_wait_scan does not exist
in /proc/modules
[ 11.566997] gameport gameport0: CS4281 Gameport is pci0001:c8:01.0/
gameport0, speed 810kHz
[ 11.802218] EXT4-fs (sda2): mounted filesystem with ordered data
mode. Opts: (null)
[ 11.821825] SELinux: initialized (dev sda2, type ext4), uses xattr
[ 12.548237] fedora-storage-init[634]: Setting up Logical Volume
Management: 3 logical volume(s) in volume group "vg_power" now active
[ 12.674497] fedora-storage-init[634]: [ OK ]
[ 12.800742] systemd-fsck[650]: /dev/mapper/vg_power-lv_home:
recovering journal
[ 12.906807] systemd-fsck[650]: /dev/mapper/vg_power-lv_home: clean,
11/1357216 files, 129207/5423104 blocks
[ 13.158111] EXT4-fs (dm-2): mounted filesystem with ordered data
mode. Opts: (null)
[ 13.158126] SELinux: initialized (dev dm-2, type ext4), uses xattr
[ 13.362556] fedora-storage-init[655]: Setting up Logical Volume
Management: 3 logical volume(s) in volume group "vg_power" now active
[ 13.377223] fedora-storage-init[655]: [ OK ]
[ 13.746098] lvm[675]: 3 logical volume(s) in volume group
"vg_power" monitored
[ 14.229775] systemd-tmpfiles[681]: Successfully loaded SELinux
database in 24ms 212us, size on heap is 479K.
[ 14.781350] alsactl[683]: /sbin/alsactl: load_state:1586: Cannot
open /var/lib/alsa/asound.state for reading: No such file or directory
[ 14.830395] alsactl[683]: Found hardware: "CS4281" "Cirrus Logic
CS4299 rev 4" "AC97a:43525934" "0x0143" "0x1804"
[ 14.830410] alsactl[683]: Hardware is initialized using a generic
method
[ 15.322594] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 15.353573] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 15.392603] iptables.init[695]: iptables: Applying firewall rules:
[ OK ]
[ 15.446338] auditctl[722]: No rules
[ 15.446351] auditctl[722]: AUDIT_STATUS: enabled=0 flag=1 pid=0
rate_limit=0 backlog_limit=320 lost=0 backlog=0
[ 15.456077] auditd[710]: Started dispatcher: /sbin/audispd pid: 735
[ 15.516198] audispd[735]: priority_boost_parser called with: 4
[ 15.516212] audispd[735]: max_restarts_parser called with: 10
[ 15.534317] audispd[735]: audispd initialized with q_depth=120 and
1 active plugins
[ 15.558627] auditd[710]: Init complete, auditd 2.1.3 listening for
events (startup state enable)
[ 15.641603] ip6tables.init[688]: ip6tables: Applying firewall
rules: [ OK ]
[ 16.457875] NetworkManager[747]: NetworkManager[747]: <info>
NetworkManager (version 0.9.2-1.fc16) is starting...
[ 16.457892] NetworkManager[747]: <info> NetworkManager (version
0.9.2-1.fc16) is starting...
[ 16.457906] NetworkManager[747]: NetworkManager[747]: <info> Read
config file /etc/NetworkManager/NetworkManager.conf
[ 16.457920] NetworkManager[747]: <info> Read config file /etc/
NetworkManager/NetworkManager.conf
[ 16.678795] avahi-daemon[766]: Found user 'avahi' (UID 70) and
group 'avahi' (GID 70).
[ 16.679008] avahi-daemon[766]: Successfully dropped root privileges.
[ 16.679794] avahi-daemon[766]: avahi-daemon 0.6.30 starting up.
[ 16.702163] avahi-daemon[766]: WARNING: No NSS support for mDNS
detected, consider installing nss-mdns!
[ 17.065033] sshd-keygen[752]: Generating SSH2 RSA host key: [ OK ]
[ 18.035051] sshd-keygen[752]: Generating SSH1 RSA host key: [ OK ]
[ 18.504970] dbus[784]: avc: netlink poll: error 4
[ 18.504982] dbus[784]: avc: netlink poll: error 4
[ 18.504994] dbus-daemon[784]: dbus[784]: avc: netlink poll: error 4
[ 18.505005] dbus-daemon[784]: dbus[784]: avc: netlink poll: error 4
[ 18.523280] abrtd[729]: Init complete, entering main loop
[ 18.525089] dbus[784]: [system] Activating systemd to hand-off:
service name='org.freedesktop.NetworkManager' unit='dbus-
org.freedesktop.NetworkManager.service'
[ 18.525238] dbus-daemon[784]: dbus[784]: [system] Activating
systemd to hand-off: service name='org.freedesktop.NetworkManager'
unit='dbus-org.freedesktop.NetworkManager.service'
[ 18.525855] avahi-daemon[766]: Successfully called chroot().
[ 18.525867] avahi-daemon[766]: Successfully dropped remaining
capabilities.
[ 18.527966] systemd-logind[771]: New seat seat0.
[ 18.534317] dbus[784]: [system] Successfully activated service
'org.freedesktop.systemd1'
[ 18.534330] dbus-daemon[784]: dbus[784]: [system] Successfully
activated service 'org.freedesktop.systemd1'
[ 18.553393] avahi-daemon[766]: Loading service file /services/
ssh.service.
[ 18.569232] avahi-daemon[766]: Loading service file /services/
udisks.service.
[ 18.598807] sshd-keygen[752]: Generating SSH2 DSA host key: [ OK ]
[ 18.606053] avahi-daemon[766]: Network interface enumeration
completed.
[ 18.606066] avahi-daemon[766]: Registering HINFO record with values
'PPC64'/'LINUX'.
[ 18.606078] avahi-daemon[766]: Server startup complete. Host name
is power.local. Local service cookie is 239314884.
[ 18.606090] avahi-daemon[766]: Service "power" (/services/
udisks.service) successfully established.
[ 18.606102] avahi-daemon[766]: Service "power" (/services/
ssh.service) successfully established.
[ 18.728015] /usr/sbin/crond[783]: (CRON) INFO (running with inotify
support)
[ 19.380854] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.384562] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.387286] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow
Control: RX/TX
[ 19.387705] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.826906] eth0: no IPv6 routers present
[root at power ~]#
somewhat cool an vintage iron! well done...
Cheers Link
More information about the ppc
mailing list