<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=us-ascii">
<META content="MSHTML 6.00.2800.1476" name=GENERATOR></HEAD>
<BODY>
<DIV><SPAN class=182095613-22102004><FONT face=Arial size=2>I just upgraded from
FC2 to FC3test3 and noticed a new behavior with my Netgear
WG511.</FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial size=2>In FC2 I would get a
failure during network init because eth1 (the prism54) was not found. As soon as
pcmcia started then the module would load and insert into my wireless network
without any action from me.</FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial size=2>Now in FC3test3, the
prism54 module loads and complains about not being able to load the firmware
(the firmware is in the correct place according to /etc/hotplug/firmware.agent).
As soon as get a shell I rmmod prism54 and modprobe prism54 and it loads and is
able to upload the firmware just fine (which I have now added the rmmod and
modprobe to rc.local so I can reboot remotely and still gain access after
reboot). I updated all packages (including kernel) that were available from yum
and the same symptoms are there. I searched bugzilla and didn't see anything on
the prism54.</FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial size=2>Has anyone seen
this, or should it go to bugzilla?</FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2>dmesg:</FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2></FONT></SPAN> </DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2>.......</FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial size=2>device-mapper:
4.1.0-ioctl (2003-12-10) initialised: <A
href="mailto:dm@uk.sistina.com">dm@uk.sistina.com</A><BR>cdrom: open
failed.<BR>kjournald starting. Commit interval 5 seconds<BR>EXT3 FS on
hda1, internal journal<BR>EXT3-fs: mounted filesystem with ordered data
mode.<BR>Adding 524152k swap on /dev/hda3. Priority:-1 extents:1<BR>IA-32
Microcode Update Driver: v1.14 <<A
href="mailto:tigran@veritas.com">tigran@veritas.com</A>><BR>microcode: No new
microdata for cpu 0<BR>ip_tables: (C) 2000-2002 Netfilter core
team<BR>ip_tables: (C) 2000-2002 Netfilter core team<BR>eth1:
islpci_open()<BR>eth1: resetting device...<BR>eth1: uploading
firmware...<BR>prism54: request_firmware() failed for 'isl3890'<BR>eth1: could
not upload firmware ('isl3890')<BR>eth1: islpci_open()<BR>eth1: resetting
device...<BR>eth1: uploading firmware...<BR>prism54: request_firmware() failed
for 'isl3890'<BR>eth1: could not upload firmware ('isl3890')<BR>eth1:
islpci_open()<BR>eth1: resetting device...<BR>eth1: uploading
firmware...<BR>prism54: request_firmware() failed for 'isl3890'<BR>eth1: could
not upload firmware ('isl3890')<BR>eth1: islpci_open()<BR>eth1: resetting
device...<BR>eth1: uploading firmware...<BR>prism54: request_firmware() failed
for 'isl3890'<BR>eth1: could not upload firmware ('isl3890')<BR>eth1:
islpci_open()<BR>eth1: resetting device...<BR>eth1: uploading
firmware...<BR>prism54: request_firmware() failed for 'isl3890'<BR>eth1: could
not upload firmware ('isl3890')<BR>cs: IO port probe 0x0c00-0x0cff:
clean.<BR>cs: IO port probe 0x0100-0x04ff: excluding 0x170-0x177 0x370-0x377
0x4d0-0x4d7<BR>cs: IO port probe 0x0a00-0x0aff: clean.<BR>i2c /dev entries
driver<BR>lp: driver loaded but no devices found ---------------- End of
boot</FONT></SPAN><SPAN class=182095613-22102004><FONT face=Arial
size=2><BR>eth1: removing device ---------------------------- rmmod
prism54<BR>divert: freeing divert_blk for eth1<BR>Unloaded prism54
driver<BR>Loaded prism54 driver, version 1.2 ---------------------- modprobe
prism54<BR>ACPI: PCI interrupt 0000:06:00.0[A] -> GSI 11 (level, low) ->
IRQ 11<BR>divert: allocating divert_blk for eth1<BR>ip_tables: (C) 2000-2002
Netfilter core team<BR>eth1: islpci_open()<BR>eth1: resetting device...<BR>eth1:
uploading firmware...<BR>eth1: firmware uploaded done, now triggering
reset...<BR>ip_tables: (C) 2000-2002 Netfilter core team<BR></FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2>lspci:</FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial size=2>00:00.0 Host bridge:
Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)<BR>00:01.0 PCI
bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)<BR>00:04.0
CardBus bridge: Texas Instruments PCI1450 (rev 03)<BR>00:04.1 CardBus bridge:
Texas Instruments PCI1450 (rev 03)<BR>00:07.0 Bridge: Intel Corp. 82371AB/EB/MB
PIIX4 ISA (rev 02)<BR>00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE
(rev 01)<BR>00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev
01)<BR>00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)<BR>00:08.0
Multimedia audio controller: ESS Technology ES1978 Maestro 2E (rev
10)<BR>00:09.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100]
(rev 09)<BR>00:09.1 Serial controller: Agere Systems (former Lucent
Microelectronics) LT WinModem<BR>01:00.0 VGA compatible controller: ATI
Technologies Inc Rage Mobility P/M AGP 2x (rev 64)<BR>06:00.0 Network
controller: Intersil Corporation Intersil ISL3890 [Prism GT/Prism Duette] (rev
01)<BR></FONT></SPAN></DIV>
<DIV><SPAN class=182095613-22102004><FONT face=Arial
size=2> </DIV></FONT></SPAN></BODY></HTML>