Linux version 2.6.17-1.2630.fc6 (brewbuilder@hs20-bc1-7.build.redhat.com) (gcc version 4.1.1 20060828 (Red Hat 4.1.1-20)) #1 SMP Wed Sep 6 16:16:03 EDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001ffb0000 (usable)
 BIOS-e820: 000000001ffb0000 - 000000001ffc0000 (ACPI data)
 BIOS-e820: 000000001ffc0000 - 000000001fff0000 (ACPI NVS)
 BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000ff780
Using x86 segment limits to approximate NX protection
DMI 2.3 present.
Using APIC driver default
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:df780000)
Detected 1802.450 MHz processor.
Built 1 zonelists.  Total pages: 130992
Kernel command line: ro root=LABEL=/12 selinux=0 audit=0 console=tty0 console=ttyS0,115200n8  
audit: disabled (after initialization)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0812000 soft=c07f2000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES:    8
... MAX_LOCK_DEPTH:          30
... MAX_LOCKDEP_KEYS:        2048
... CLASSHASH_SIZE:           1024
... MAX_LOCKDEP_ENTRIES:     8192
... MAX_LOCKDEP_CHAINS:      8192
... CHAINHASH_SIZE:          4096
 memory used by lock dependency info: 696 kB
 per task-struct memory footprint: 1200 bytes
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511304k/523968k available (2139k kernel code, 12032k reserved, 1126k data, 240k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3609.59 BogoMIPS (lpj=7219187)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: AMD Athlon(tm) 64 Processor 3000+ stepping 02
Total of 1 processors activated (3609.59 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
Brought up 1 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 1468k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: enabled onboard AC97/MC97 devices
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 16 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
pnp: 00:08: ioport range 0x680-0x6ff has been reserved
pnp: 00:08: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: faf00000-fbffffff
  PREFETCH window: f0000000-f9ffffff
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 7, 524288 bytes)
TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1157875780.904:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 5777688813E6B79A
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
0000:00:10.4 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 128M @ 0xe8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 169
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 9
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hda: SAMSUNG SP0411N, ATA DISK drive
hdb: SAMSUNG SP0411N, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: BENQ DVD DD DW1640, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3
hdb: max request size: 512KiB
hdb: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hdb: cache flushes supported
 hdb: hdb1
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (version 2.10.00)
powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x6
powernow-k8:    1 : fid 0x2 (1000 MHz), vid 0x12
Using IPI No-Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
 S0 S1 S3 S4 S5)
Freeing unused kernel memory: 240k freed
Write protecting the kernel read-only data: 400k
Red Hat nash version 5.1.15 starting
Mounting proc filesystem
Mounting sysfs filesystem
Creating /dev
Creating initial device nodes
Setting up hotplug.
input: AT Translated Set 2 keyboard as /class/input/input0
Creating block device nodes.
Loading uhci-hcd.ko module
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.0, from 11 to 1
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 177, io base 0x0000d800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.1, from 11 to 1
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 177, io base 0x0000e000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.2, from 5 to 1
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 177, io base 0x0000e400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
Loading ohci-hcd.ko module
Loading ehci-hcd.ko module
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 177
PCI: VIA IRQ fixup for 0000:00:10.4, from 5 to 1
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.4: irq 177, io mem 0xfae00000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Loading jbd.ko module
Loading ext3.ko module
Loading scsi_mod.ko module
SCSI subsystem initialized
Loading sd_mod.ko module
Loading libata.ko module
Loading sata_via.ko module
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 169
sata_via 0000:00:0f.0: routed to hard irq line 5
ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD002 bmdma 0xC000 irq 169
ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xC402 bmdma 0xC008 irq 169
scsi0 : sata_via
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7, max UDMA7, 390721968 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : sata_via
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xC807
  Vendor: ATA       Model: SAMSUNG SP2004C   Rev: VM10
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
Trying to resume from LABEL=SWAP-hda3
usb 1-1: new low speed USB device using uhci_hcd and address 3
No suspend signature on swap, not resuming.
Creating root device.
Mounting root filesystem.
usb 1-1: configuration #1 chosen from 1 choice
input: Logitech USB RECEIVER as /class/input/input1
input: USB HID v1.11 Mouse [Logitech USB RECEIVER] on usb-0000:00:10.0-1
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Setting up other filesystems.
Setting up new root fs
no fstab.sys, mounting internal defaults
Switching to new root and running init.
unmounting old /dev
unmounting old /proc
unmounting old /sys
INIT: version 2.86 booting
		Welcome to Fedora Core
		Press 'I' to enter interactive startup.
Setting clock  (localtime): Sun Sep 10 08:10:01 CEST 2006 [  OK  ]
Starting udev: [  OK  ]
Setting hostname fc6.localdomain:  [  OK  ]
No devices found
Missing major number for persistent device.
Couldn't create ioctl argument.
last_lba(): I don't know how to handle files with mode 41ed
read error, sector 0
read error, sector 1
read error, sector 29
Missing major number for persistent device.
Couldn't create ioctl argument.
Setting up Logical Volume Management:   /dev/hdc: open failed: No medium found
  Attempt to close device '/dev/hdc' which is not open.
  No volume groups found
[  OK  ]
Checking filesystems
Checking all file systems.
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda6 
/12: clean, 92418/2445600 files, 681011/2443880 blocks
[  OK  ]
Remounting root filesystem in read-write mode:  [  OK  ]
Mounting local filesystems:  [  OK  ]
Enabling local filesystem quotas:  [  OK  ]
Enabling /etc/fstab swaps:  swapon: /dev/hda3: Invalid argument
[FAILED]
INIT: Entering runlevel: 5
Entering non-interactive startup
Starting readahead_early:  Starting background readahead: [  OK  ]
[  OK  ]
Checking for hardware changes [  OK  ]
Applying ip6tables firewall rules: [  OK  ]
Applying iptables firewall rules: [  OK  ]
Loading additional iptables modules: ip_conntrack_netbios_ns [  OK  ]
Bringing up loopback interface:  [  OK  ]
Bringing up interface eth1:  
Determining IP information for eth1... done.
[  OK  ]
Starting system logger: [  OK  ]
Starting kernel logger: [  OK  ]
Starting irqbalance: [  OK  ]
Starting portmap: [  OK  ]
Starting NFS statd: [  OK  ]
Starting RPC idmapd: [  OK  ]
Starting system message bus: Unknown username "named" in message bus configuration file
[  OK  ]
Starting Bluetooth services:[  OK  ][  OK  ]
Mounting other filesystems:  [  OK  ]
Starting PC/SC smart card daemon (pcscd): [  OK  ]
Starting hidd: [  OK  ]
Loading autofs4: [  OK  ]
Starting automount: [  OK  ]
Starting acpi daemon: [  OK  ]
Starting hpiod: [  OK  ]
Starting hpssd: [  OK  ]
Starting cups: [  OK  ]
Starting sshd: [  OK  ]
Starting sendmail: [  OK  ]
Starting sm-client: [  OK  ]
Starting console mouse services: [  OK  ]
Starting crond: [  OK  ]
Starting xfs: [  OK  ]
Starting anacron: [  OK  ]
Starting atd: [  OK  ]
Starting readahead_later:  Starting background readahead: [  OK  ]
[  OK  ]
Starting yum-updatesd: [  OK  ]
Starting Avahi daemon: [  OK  ]
Starting HAL daemon: [  OK  ]
Starting smartd: [  OK  ]

Fedora Core release 5.92 (FC6 Test3)
Kernel 2.6.17-1.2630.fc6 on an i686

fc6.localdomain login: 