[fedora-arm] Rawhide on BeagleBone Black
I received a BeagleBone Black (rev B) today and naturally wanted to
get Fedora running on it. The Fedora 20 image booted fine, although
after doing a yum update it wouldn't load the kernel anymore, it just
stuck at "starting kernel...". Anyhow, after reading a few of the
threads on this list I though that I'd give rawhide a try. Here's a
log of my latest attempt (I already had a copy of MLO and u-boot.img
from a previous attempt):
[root@lt33223 ~]# umount /dev/mmcblk0p1
[root@lt33223 ~]# umount /dev/mmcblk0p3
[root@lt33223 bbb]# wipefs -a /dev/mmcblk0
/dev/mmcblk0: 2 bytes were erased at offset 0x000001fe (dos): 55 aa
/dev/mmcblk0: calling ioclt to re-read partition table: Success
[root@lt33223 bbb]# xzcat
Fedora-Minimal-armhfp-rawhide-20140508-sda.raw.xz | dd of=/dev/mmcblk0
bs=4M
0+259756 records in
0+259756 records out
2139095040 bytes (2.1 GB) copied, 525.464 s, 4.1 MB/s
[root@lt33223 bbb]# sync
[root@lt33223 bbb]# dd if=/tmp/MLO of=/dev/mmcblk0 count=1 seek=1
conv=notrunc bs=128k
0+1 records in
0+1 records out
81904 bytes (82 kB) copied, 0.0284869 s, 2.9 MB/s
[root@lt33223 bbb]# sync
[root@lt33223 bbb]# dd if=/tmp/u-boot.img of=/dev/mmcblk0 count=2
seek=1 conv=notrunc bs=384k
1+1 records in
1+1 records out
415481 bytes (415 kB) copied, 0.115809 s, 3.6 MB/s
[root@lt33223 bbb]# sync
And here's what I get when I try and boot it up:
U-Boot SPL 2013.04-dirty (Jul 10 2013 - 14:02:53)
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
OMAP SD/MMC: 0
mmc_send_cmd : timeout: No status update
reading u-boot.img
reading u-boot.img
U-Boot 2013.04-dirty (Jul 10 2013 - 14:02:53)
I2C: ready
DRAM: 512 MiB
WARNING: Caches not enabled
NAND: No NAND device found!!!
0 MiB
MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1
*** Warning - readenv() failed, using default environment
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Peripheral mode controller at 47401000 using PIO, IRQ 0
musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn)
musb-hdrc: MHDRC RTL version 2.0
musb-hdrc: setup fifo_mode 4
musb-hdrc: 28/31 max ep, 16384/16384 memory
USB Host mode controller at 47401800 using PIO, IRQ 0
Net: <ethaddr> not set. Validating first E-fuse MAC
cpsw, usb_ether
Hit any key to stop autoboot: 0
gpio: pin 53 (gpio 53) value is 1
mmc0 is current device
micro SD card found
mmc0 is current device
gpio: pin 54 (gpio 54) value is 1
SD/MMC found on device 0
** File not found uEnv.txt **
gpio: pin 55 (gpio 55) value is 1
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
U-Boot#
Can anyone tell me what I'm doing wrong here?
--
Jeff Ollie