U-Boot 2013.10-rc2 (Sep 03 2013 - 04:10:35)

CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
Reset cause: WDOG
Board: Wandboard
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Warning: FEC using MAC address from net device

  *** U-Boot Boot Menu ***  Press UP/DOWN to move, ENTER to select     U-Boot console  Hit any key to stop autoboot:  2  1  0 => printenv
baudrate=115200
boot_fdt=try
bootargs=console=ttymxc0 root=LABEL=rootfs
bootcmd=mmc dev ${mmcdev}; if mmc rescan; then run bootcmd_default; if run loadbootscript; then run bootscript; else if run loaduimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi
bootcmd_default=run bootcmd_mmc; run bootcmd_sata; run bootcmd_pxe
bootcmd_disk=run bootcmd_disk_sysboot1; run bootcmd_disk_sysboot2; run bootcmd_disk_uenv; run bootcmd_disk_scr; run bootcmd_disk_kernel
bootcmd_disk_kernel=ext2load ${boot_ifc} ${bootdevice} ${kernel_addr_r} vmlinuz && ext2load ${boot_ifc} ${bootdevice} ${ramdisk_addr_r} initrd.img && bootz ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr}
bootcmd_disk_scr=ext2load ${boot_ifc} ${bootdevice} ${scr_addr_r} boot.scr && source ${scr_addr_r}
bootcmd_disk_sysboot1=setenv bootfile /boot/extlinux/extlinux.conf; sysboot ${boot_ifc} ${bootdevice} ext2
bootcmd_disk_sysboot2=setenv bootfile /extlinux/extlinux.conf; sysboot ${boot_ifc} ${bootdevice} ext2
bootcmd_disk_uenv=ext2load ${boot_ifc} ${bootdevice} ${uenv_addr_r} uEnv.txt; env import -t ${uenv_addr_r} ${filesize}; run bootcmd_uenv
bootcmd_mmc=setenv boot_ifc mmc; mmc rescan && run bootcmd_disk
bootcmd_pxe=setenv bootfile "" ;dhcp; pxe get; pxe boot
bootcmd_sata=setenv boot_ifc scsi; scsi scan && run bootcmd_disk
bootcmd_setup=mmc rescan
bootdelay=2
bootdevice=0
bootretry=90
bootscript=echo Running bootscript from mmc ...; source
console=ttymxc0
ethact=FEC
ethaddr=00:1f:7b:b2:02:4a
ethprime=FEC
fdt_addr=0x11000000
fdt_addr_r=0x12000000
fdt_file=imx6dl-wandboard.dtb
fdt_high=0xffffffff
initrd_high=0xffffffff
ip_dyn=yes
kernel_addr_r=0x14000000
loadaddr=0x12000000
loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};
loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}
loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}
localcmd=run bootcmd_mmc
mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot}
mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if run loadfdt; then bootm ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootm; else echo WARN: Cannot load the DT; fi; fi; else bootm; fi;
mmcdev=0
mmcpart=1
mmcroot=/dev/mmcblk0p2 rootwait rw
netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp
netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; ${get_cmd} ${uimage}; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if ${get_cmd} ${fdt_addr} ${fdt_file}; then bootm ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootm; else echo WARN: Cannot load the DT; fi; fi; else bootm; fi;
netretry=once
pxefile_addr_r=0x13000000
ramdisk_addr_r=0x32000000
script=boot.scr
splashpos=m,m
uimage=uImage
update_sd_firmware=if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; if mmc dev ${mmcdev}; then if ${get_cmd} ${update_sd_firmware_filename}; then setexpr fw_sz ${filesize} / 0x200; setexpr fw_sz ${fw_sz} + 1; mmc write ${loadaddr} 0x2 ${fw_sz}; fi; fi
update_sd_firmware_filename=u-boot.imx

Environment size: 3332/8188 bytes
=> ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script}
18053 bytes read in 104 ms (168.9 KiB/s)
=> sourrce ${loadaddr}
## Executing script at 12000000
Welcome to a-b-c 0.59.

Configuring for wandboard
Configuring for imx
Found kernel_addr_r (0x14000000), using for u_k_addr.
Found ramdisk_addr_r (0x32000000), using for u_ramfs_addr.
Found fdt_addr_r (0x12000000), using for u_dtb_addr.
Found fdt_addr (0x11000000), using for u_dtb_addr.
Using defaults for imx6dl-wandboard.dtb, and will load dtb during startup.
Will scan for kernels on mmc usb, using ext2 filesystems with bootz

Starting menu init....

Using kernel k2 (3.11.0-300.fc20.armv7hl).
Auto-booting 3.11.0-300.fc20.armv7hl in 3 seconds. Type ^C to abort then run menu for help.
 3 2 1...
4748528 bytes read in 306 ms (14.8 MiB/s)
10760235 bytes read in 607 ms (16.9 MiB/s)
21000 bytes read in 221 ms (92.8 KiB/s)
bootargs are ro rootwait rhgb quiet root=UUID=e72ec2c4-bd9e-4100-85be-df34e7f01e53 console=ttymxc0
Kernel image @ 0x14000000 [ 0x000000 - 0x4874f0 ]
## Loading init Ramdisk from Legacy Image at 32000000 ...
   Image Name:   initramfs
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    10760171 Bytes = 10.3 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 11000000
   Booting using the fdt blob at 0x11000000
   Using Device Tree in place at 11000000, end 11008207

Starting kernel ...