1:55 a.m.
Hello Guys,
Here are some printouts for the R1:
root@bananapi_r1 /home/user # lshw
bananapi_r1.homenet
description: Computer
product: LeMaker Banana Pi
width: 32 bits
*-core
description: Motherboard
physical id: 0
capabilities: lemaker_bananapi allwinner_sun7i-a20
*-cpu:0
description: CPU
product: cpu
physical id: 0
bus info: cpu@0
*-cpu:1 DISABLED
description: CPU
product: cpu
physical id: 1
bus info: cpu@1
*-memory
description: System memory
physical id: 2
size: 1001MiB
*-usbhost:0
product: EHCI Host Controller
vendor: Linux 3.17.7-300.fc21.armv7hl ehci_hcd
physical id: 1
bus info: usb@4
logical name: usb4
version: 3.17
capabilities: usb-2.00
configuration: driver=hub slots=1 speed=480Mbit/s
*-usb
description: Ethernet interface
product: D-Link DUB-1312
vendor: D-Link Elec. Corp.
physical id: 1
bus info: usb@4:1
logical name: eth1
version: 1.00
serial: 000000000007C8
size: 1Gbit/s
capacity: 1Gbit/s
capabilities: usb-2.10 ethernet physical tp mii 10bt 10bt-fd
100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes
driver=ax88179_178a duplex=full ip=192.168.1.158 link=yes maxpower=248mA
multicast=yes port=MII speed=1Gbit/s
*-usbhost:1
product: Generic Platform OHCI controller
vendor: Linux 3.17.7-300.fc21.armv7hl ohci_hcd
physical id: 2
bus info: usb@3
logical name: usb3
version: 3.17
capabilities: usb-1.10
configuration: driver=hub slots=1 speed=12Mbit/s
*-usbhost:2
product: Generic Platform OHCI controller
vendor: Linux 3.17.7-300.fc21.armv7hl ohci_hcd
physical id: 3
bus info: usb@2
logical name: usb2
version: 3.17
capabilities: usb-1.10
configuration: driver=hub slots=1 speed=12Mbit/s
*-usbhost:3
product: EHCI Host Controller
vendor: Linux 3.17.7-300.fc21.armv7hl ehci_hcd
physical id: 4
bus info: usb@1
logical name: usb1
version: 3.17
capabilities: usb-2.00
configuration: driver=hub slots=1 speed=480Mbit/s
*-usb
description: Wireless interface
product: 802.11n WLAN Adapter
vendor: Realtek
physical id: 1
bus info: usb@1:1
logical name: wlan0
version: 2.00
serial: 00e04c000001
capabilities: usb-2.00 ethernet physical wireless
configuration: broadcast=yes driver=rtl8192cu
driverversion=3.17.7-300.fc21.armv7hl firmware=N/A link=no
maxpower=500mA multicast=yes speed=480Mbit/s wireless=IEEE 802.11bgn
*-network
description: Ethernet interface
physical id: 5
logical name: eth0
serial: 02:58:02:42:91:71
size: 10Mbit/s
capacity: 1Gbit/s
capabilities: ethernet physical tp aui bnc mii fibre 10bt
10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=st_gmac
driverversion=March_2013 duplex=half link=no multicast=yes port=MII
speed=10Mbit/s
Not sure what the meaning of DISABLED next to cpu1 is , if there is any
meaning , it could be just lshw playing up .
root@bananapi_r1 /home/user # cat /proc/cpuinfo
processor : 0
model name : ARMv7 Processor rev 4 (v7l)
Features : half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpv4
idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xc07
CPU revision : 4
processor : 1
model name : ARMv7 Processor rev 4 (v7l)
Features : half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpv4
idiva idivt vfpd32 lpae evtstrm
CPU implementer : 0x41
CPU architecture: 7
CPU variant : 0x0
CPU part : 0xc07
CPU revision : 4
Hardware : Allwinner sun7i (A20) Family
Revision : 0000
Serial : 0000000000000000
root@bananapi_r1 /home/user # ethtool eth0
Settings for eth0:
Supported ports: [ TP AUI BNC MII FIBRE ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 0
Transceiver: external
Auto-negotiation: on
Supports Wake-on: d
Wake-on: d
Current message level: 0x0000003f (63)
drv probe link timer ifdown ifup
Link detected: no
root@bananapi_r1 /home/user # ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet6 fe80::58:2ff:fe42:9171 prefixlen 64 scopeid 0x20<link>
ether 02:58:02:42:91:71 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 4 bytes 600 (600.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 117
eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.158 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fdc1:4e49:af09:1:ee28:80ff:fea3:40f3 prefixlen 64
scopeid 0x0<global>
inet6 fe80::ee28:80ff:fea3:40f3 prefixlen 64 scopeid 0x20<link>
ether ec:28:80:a3:40:f3 txqueuelen 1000 (Ethernet)
RX packets 1353 bytes 343833 (335.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1026 bytes 118391 (115.6 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 16 bytes 1504 (1.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 16 bytes 1504 (1.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether ac:a2:13:5c:ab:9c txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
root@bananapi_r1 /home/user # dmesg | grep -i eth
[ 0.000000] psci: probing for conduit method from DT.
[ 9.420969] stmmaceth 1c50000.ethernet: no reset control found
[ 9.579996] eth0: PHY ID 03625f24 at 0 IRQ POLL (stmmac-0:00) active
[ 9.586409] eth0: PHY ID 03625f24 at 1 IRQ POLL (stmmac-0:01)
[ 9.592238] eth0: PHY ID 03625f24 at 2 IRQ POLL (stmmac-0:02)
[ 9.598031] eth0: PHY ID 03625f24 at 3 IRQ POLL (stmmac-0:03)
[ 9.603850] eth0: PHY ID 03625f24 at 4 IRQ POLL (stmmac-0:04)
[ 9.617363] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
[ 11.559795] ax88179_178a 4-1:1.0 eth1: register 'ax88179_178a' at
usb-1c14000.usb-1, D-Link DUB-1312 USB 3.0 to Gigabit Ethernet Adapter,
ec:28:80:a3:40:f3
[ 14.014524] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 17.021829] ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1
[ 17.035573] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
root@bananapi_r1 /home/user # uname -a
Linux bananapi_r1.homenet 3.17.7-300.fc21.armv7hl #1 SMP Wed Dec 17
04:38:18 UTC 2014 armv7l armv7l armv7l GNU/Linux