6:48 a.m.
Do I run
xzcat Fedora-Xfce-armhfp-20-a10-1-sda.raw.xz > /dev/sbd
or
xzcat Fedora-Xfce-armhfp-20-a10-1-sda.raw.xz > /dev/sbd1
??
The mount was to sbd1, but the device is sbd
6:52 a.m.
On Fri, May 30, 2014 at 12:48 PM, Robert Moskowitz <rgm(a)htt-consult.com> wrote:
Do I run
xzcat Fedora-Xfce-armhfp-20-a10-1-sda.raw.xz > /dev/sbd
or
xzcat Fedora-Xfce-armhfp-20-a10-1-sda.raw.xz > /dev/sbd1
??
The mount was to sbd1, but the device is sbd
Always the root device. So /dev/sdb (I think you have the b and the d
back to front) and make sure you umount it first.
Peter
7:19 a.m.
On 05/30/2014 07:52 AM, Peter Robinson wrote:
On Fri, May 30, 2014 at 12:48 PM, Robert Moskowitz
<rgm(a)htt-consult.com> wrote:
> Do I run
>
> xzcat Fedora-Xfce-armhfp-20-a10-1-sda.raw.xz > /dev/sbd
>
> or
>
> xzcat Fedora-Xfce-armhfp-20-a10-1-sda.raw.xz > /dev/sbd1
>
>
> ??
>
> The mount was to sbd1, but the device is sbd
Always the root device. So /dev/sdb (I think you have the b and the d
back to front) and make sure you umount it first.
My dyslexia at work. :)
It finally finished. And then did the uboot install booted up but....
My setup here has an hdmo/vga adapter plugged into a KVM switch that
limits me to 1024x768 thus I cannot see the bottom of the change root
password screen to know what keystroke (can't mouse down to what is
below the screen) to accept the password change.
help please. :(
4:26 p.m.
On Fri, May 30, 2014 at 08:19:13AM -0400, Robert Moskowitz wrote:
My setup here has an hdmo/vga adapter plugged into a KVM switch that
limits me to 1024x768 thus I cannot see the bottom of the change
root password screen to know what keystroke (can't mouse down to
what is below the screen) to accept the password change.
I always use serial cables with these ARM boards. A "CP2102" (search
for that on Amazon) cable will set you back a few dollars and save you
a lot of heartache!
Rich.
--
Richard Jones, Virtualization Group, Red Hat http://people.redhat.com/~rjones
Read my programming and virtualization blog: http://rwmj.wordpress.com
virt-df lists disk usage of guests without needing to install any
software inside the virtual machine. Supports Linux and Windows.
http://people.redhat.com/~rjones/virt-df/
4:36 p.m.
On 05/30/2014 05:26 PM, Richard W.M. Jones wrote:
On Fri, May 30, 2014 at 08:19:13AM -0400, Robert Moskowitz wrote:
> My setup here has an hdmo/vga adapter plugged into a KVM switch that
> limits me to 1024x768 thus I cannot see the bottom of the change
> root password screen to know what keystroke (can't mouse down to
> what is below the screen) to accept the password change.
I always use serial cables with these ARM boards. A "CP2102" (search
for that on Amazon) cable will set you back a few dollars and save you
a lot of heartache!
I do have one around here somewhere. Got to find it and figure out how
to use it.
10:16 p.m.
On Fri, May 30, 2014 at 5:36 PM, Robert Moskowitz <rgm(a)htt-consult.com> wrote:
On 05/30/2014 05:26 PM, Richard W.M. Jones wrote:
>
> On Fri, May 30, 2014 at 08:19:13AM -0400, Robert Moskowitz wrote:
>>
>> My setup here has an hdmo/vga adapter plugged into a KVM switch that
>> limits me to 1024x768 thus I cannot see the bottom of the change
>> root password screen to know what keystroke (can't mouse down to
>> what is below the screen) to accept the password change.
>
> I always use serial cables with these ARM boards. A "CP2102" (search
> for that on Amazon) cable will set you back a few dollars and save you
> a lot of heartache!
I do have one around here somewhere. Got to find it and figure out how to
use it.
You may also attempt to mount the sd card on another machine and
surgically set the password in /etc/shadow.
(or any other post install config tasks)
--
-Jon
3615
days inactive
3616
days old
5 comments
4 participants
participants (4)
-
Jon -
Peter Robinson -
Richard W.M. Jones -
Robert Moskowitz