My Firmware is UEFI , but I don’t know whether or not to upgrade it,running like this:
TianoCore 1.1.0-rh-0.15 UEFI 2.4.0 Mar 13 2015 14:20:16 CPU: APM ARM 64-bit Potenza Rev A3 2400MHz PCP 2400MHz 32 KB ICACHE, 32 KB DCACHE SOC 2000MHz IOBAXI 400MHz AXI 250MHz AHB 200MHz GFC 125MHz Board: X-Gene Mustang Board Slimpro FW: Ver: 2.1 The default boot selection will start in 3 seconds
Need to upgrade it?? How to do? Thanks very much.
On 15/4/8 21:42, "Peter Robinson" pbrobinson@gmail.com wrote:
On Wed, Apr 8, 2015 at 2:01 PM, jefby jef199006@gmail.com wrote:
Hi,All. Today I have upgraded the kernel version from 3.17.4 to 3.19.3 (APM aarch64), found some strange error , and these error caused the system can not enter the command,I picked up the main error :
[ 43.055594] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 43.062618] ata2.00: failed command: READ DMA EXT [ 43.067316] ata2.00: cmd 25/00:08:e0:76:df/00:00:e5:00:00/e0 tag 0 dma 4096 in [ 43.067316] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 43.081865] ata2.00: status: { DRDY } [ 43.085514] ata2: hard resetting link [ 43.435577] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 4300) [ 43.442510] ata2.00: configured for UDMA/133 [ 43.446775] ata2.00: device reported invalid CHS sector 0 [ 43.452156] ata2: EH complete
[ 0.013618] WARNING: CPU: 0 PID: 1 at drivers/firmware/dmi_scan.c:657 dmi_matches+0x10c/0x110() [ 0.013623] dmi check: not initialized yet. [ 0.013626] Modules linked in: [ 0.013632] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.3-200.fc21.aarch64 #1 [ 0.013636] Hardware name: APM X-Gene Mustang board (DT) [ 0.013640] Call trace: [ 0.013646] [<fffffe0000097624>] dump_backtrace+0x0/0x164 [ 0.013651] [<fffffe00000977a4>] show_stack+0x1c/0x28 [ 0.013657] [<fffffe000077fd88>] dump_stack+0x74/0x94 [ 0.013662] [<fffffe00000bd908>] warn_slowpath_common+0xa4/0xdc [ 0.013667] [<fffffe00000bd9b4>] warn_slowpath_fmt+0x74/0x88 [ 0.013671] [<fffffe00005f9b80>] dmi_matches+0x108/0x110 [ 0.013676] [<fffffe00005f9bb4>] dmi_check_system+0x2c/0x70 [ 0.013681] [<fffffe0000c6e614>] lockup_detector_init+0x10/0x54 [ 0.013685] [<fffffe0000c60acc>] kernel_init_freeable+0x108/0x260 [ 0.013690] [<fffffe000077d7b4>] kernel_init+0x1c/0xe0 [ 0.013705] ---[ end trace f44b0c4387855b6d ]--- [ 0.013708] ------------[ cut here ]------------ [ 0.013713] WARNING: CPU: 0 PID: 1 at drivers/firmware/dmi_scan.c:657 dmi_matches+0x10c/0x110() [ 0.013718] dmi check: not initialized yet. [ 0.013721] Modules linked in: [ 0.013725] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.19.3-200.fc21.aarch64 #1 [ 0.013730] Hardware name: APM X-Gene Mustang board (DT) [ 0.013733] Call trace: [ 0.013737] [<fffffe0000097624>] dump_backtrace+0x0/0x164 [ 0.013741] [<fffffe00000977a4>] show_stack+0x1c/0x28 [ 0.013745] [<fffffe000077fd88>] dump_stack+0x74/0x94 [ 0.013750] [<fffffe00000bd908>] warn_slowpath_common+0xa4/0xdc [ 0.013754] [<fffffe00000bd9b4>] warn_slowpath_fmt+0x74/0x88 [ 0.013759] [<fffffe00005f9b80>] dmi_matches+0x108/0x110 [ 0.013763] [<fffffe00005f9bb4>] dmi_check_system+0x2c/0x70 [ 0.013767] [<fffffe0000c6e614>] lockup_detector_init+0x10/0x54 [ 0.013772] [<fffffe0000c60acc>] kernel_init_freeable+0x108/0x260 [ 0.013776] [<fffffe000077d7b4>] kernel_init+0x1c/0xe0 [ 0.013780] ---[ end trace f44b0c4387855b6e ]—
How to fix it?? Thanks very much!
What firmware are you running? The second section (dmi_scan bit) isn't the problem and won't affect the device. I'm running 4 devices in the build systems under high load with 3.19.3 kernel and it's been more stable than any of the prior kernels, I suspect you need to update the firmware with the kernel.
-
jefby