Hello Guys,
Here are some printouts for the R1:
root@bananapi_r1 /home/user # lshw bananapi_r1.homenet description: Computer product: LeMaker Banana Pi width: 32 bits *-core description: Motherboard physical id: 0 capabilities: lemaker_bananapi allwinner_sun7i-a20 *-cpu:0 description: CPU product: cpu physical id: 0 bus info: cpu@0 *-cpu:1 DISABLED description: CPU product: cpu physical id: 1 bus info: cpu@1 *-memory description: System memory physical id: 2 size: 1001MiB *-usbhost:0 product: EHCI Host Controller vendor: Linux 3.17.7-300.fc21.armv7hl ehci_hcd physical id: 1 bus info: usb@4 logical name: usb4 version: 3.17 capabilities: usb-2.00 configuration: driver=hub slots=1 speed=480Mbit/s *-usb description: Ethernet interface product: D-Link DUB-1312 vendor: D-Link Elec. Corp. physical id: 1 bus info: usb@4:1 logical name: eth1 version: 1.00 serial: 000000000007C8 size: 1Gbit/s capacity: 1Gbit/s capabilities: usb-2.10 ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=ax88179_178a duplex=full ip=192.168.1.158 link=yes maxpower=248mA multicast=yes port=MII speed=1Gbit/s *-usbhost:1 product: Generic Platform OHCI controller vendor: Linux 3.17.7-300.fc21.armv7hl ohci_hcd physical id: 2 bus info: usb@3 logical name: usb3 version: 3.17 capabilities: usb-1.10 configuration: driver=hub slots=1 speed=12Mbit/s *-usbhost:2 product: Generic Platform OHCI controller vendor: Linux 3.17.7-300.fc21.armv7hl ohci_hcd physical id: 3 bus info: usb@2 logical name: usb2 version: 3.17 capabilities: usb-1.10 configuration: driver=hub slots=1 speed=12Mbit/s *-usbhost:3 product: EHCI Host Controller vendor: Linux 3.17.7-300.fc21.armv7hl ehci_hcd physical id: 4 bus info: usb@1 logical name: usb1 version: 3.17 capabilities: usb-2.00 configuration: driver=hub slots=1 speed=480Mbit/s *-usb description: Wireless interface product: 802.11n WLAN Adapter vendor: Realtek physical id: 1 bus info: usb@1:1 logical name: wlan0 version: 2.00 serial: 00e04c000001 capabilities: usb-2.00 ethernet physical wireless configuration: broadcast=yes driver=rtl8192cu driverversion=3.17.7-300.fc21.armv7hl firmware=N/A link=no maxpower=500mA multicast=yes speed=480Mbit/s wireless=IEEE 802.11bgn *-network description: Ethernet interface physical id: 5 logical name: eth0 serial: 02:58:02:42:91:71 size: 10Mbit/s capacity: 1Gbit/s capabilities: ethernet physical tp aui bnc mii fibre 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=st_gmac driverversion=March_2013 duplex=half link=no multicast=yes port=MII speed=10Mbit/s
Not sure what the meaning of DISABLED next to cpu1 is , if there is any meaning , it could be just lshw playing up .
root@bananapi_r1 /home/user # cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 4 (v7l) Features : half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xc07 CPU revision : 4
processor : 1 model name : ARMv7 Processor rev 4 (v7l) Features : half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x0 CPU part : 0xc07 CPU revision : 4
Hardware : Allwinner sun7i (A20) Family Revision : 0000 Serial : 0000000000000000
root@bananapi_r1 /home/user # ethtool eth0 Settings for eth0: Supported ports: [ TP AUI BNC MII FIBRE ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10Mb/s Duplex: Half Port: MII PHYAD: 0 Transceiver: external Auto-negotiation: on Supports Wake-on: d Wake-on: d Current message level: 0x0000003f (63) drv probe link timer ifdown ifup Link detected: no root@bananapi_r1 /home/user # ifconfig eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 inet6 fe80::58:2ff:fe42:9171 prefixlen 64 scopeid 0x20<link> ether 02:58:02:42:91:71 txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 4 bytes 600 (600.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 117
eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.1.158 netmask 255.255.255.0 broadcast 192.168.1.255 inet6 fdc1:4e49:af09:1:ee28:80ff:fea3:40f3 prefixlen 64 scopeid 0x0<global> inet6 fe80::ee28:80ff:fea3:40f3 prefixlen 64 scopeid 0x20<link> ether ec:28:80:a3:40:f3 txqueuelen 1000 (Ethernet) RX packets 1353 bytes 343833 (335.7 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 1026 bytes 118391 (115.6 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 inet 127.0.0.1 netmask 255.0.0.0 inet6 ::1 prefixlen 128 scopeid 0x10<host> loop txqueuelen 0 (Local Loopback) RX packets 16 bytes 1504 (1.4 KiB) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 16 bytes 1504 (1.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500 ether ac:a2:13:5c:ab:9c txqueuelen 1000 (Ethernet) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
root@bananapi_r1 /home/user # dmesg | grep -i eth [ 0.000000] psci: probing for conduit method from DT. [ 9.420969] stmmaceth 1c50000.ethernet: no reset control found [ 9.579996] eth0: PHY ID 03625f24 at 0 IRQ POLL (stmmac-0:00) active [ 9.586409] eth0: PHY ID 03625f24 at 1 IRQ POLL (stmmac-0:01) [ 9.592238] eth0: PHY ID 03625f24 at 2 IRQ POLL (stmmac-0:02) [ 9.598031] eth0: PHY ID 03625f24 at 3 IRQ POLL (stmmac-0:03) [ 9.603850] eth0: PHY ID 03625f24 at 4 IRQ POLL (stmmac-0:04) [ 9.617363] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e) [ 11.559795] ax88179_178a 4-1:1.0 eth1: register 'ax88179_178a' at usb-1c14000.usb-1, D-Link DUB-1312 USB 3.0 to Gigabit Ethernet Adapter, ec:28:80:a3:40:f3 [ 14.014524] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 17.021829] ax88179_178a 4-1:1.0 eth1: ax88179 - Link status is: 1 [ 17.035573] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
root@bananapi_r1 /home/user # uname -a Linux bananapi_r1.homenet 3.17.7-300.fc21.armv7hl #1 SMP Wed Dec 17 04:38:18 UTC 2014 armv7l armv7l armv7l GNU/Linux
-
mo.ucina