laptop November 2007

laptop@lists.fedoraproject.org

22 participants
17 discussions

Wireless Broadcom BCM93411MCG wlan mini-pci
by willhs＠siu.edu 05 Dec '07

05 Dec '07

I have a compaq presario c500 running fedora core 8 (with automatic updates already installed) with a "Broadcom Corparation BCM93411MCG wlan mini-pci" card. It shows up in network configuration under hardware as an ethernet card and not a wireless connection. I tried to delete it as an ethernet and set it up as a wireless, yet "Broadcom Corparation BCM93411MCG wlan mini-pci" does not show up under "select wireless device" or "adapter type". Yet when I add it as an ethernet connection it shows up under "adapter type" or "select ethernet connection" yet if I install it, it has a status of 'ok', yet does not function or activate. Drivers? Any ideas?

2 10

Compaq F572US Locks Up with FC7
by Jim Duda 01 Dec '07

01 Dec '07

I have a Compaq F572US, with AMD Athlon Turin X86 with nvidia graphics adapter. I really like the laptop, however, it occasionally hits a hard lock up and I have to reset and reboot. The computer runs really slow with Windows Vista, but works fine with Fedora :-) I'm not sure how to tell if this is a software configuration problem or I have purchased a lemon. I'm running latest Fedora FC7 Moonshine, up-to-date. My kernel boot options are noapic irqpoll noapci Can anyone share experiences with Compaq F572US laptop computers? Thanks, Jim

1 1

ASUS M6000: dual head & upgrade to fedora 8
by dhhb2304 27 Nov '07

27 Nov '07

Since my message earlier was sent in HTML-format, I repeat it here as text: (sorry for the inconvenience) I have an Asus M6000 laptop that gives me two problems: *1. *when attaching a separate monitor to the VGA-slot on the back, I get a copy of the picture I see on the laptop screen (as it should!). Then, as root I enter into monitor management (sorry, my F7 is in Dutch, so the correct term is probably different in English) and activate dual head, giving the screen size and resolution of the external monitor. after OK, I get the order to restart X for the change to take effect. After having done this by logging out and again logging in, the laptop screen remains black and only the external monitor shows a picture. After restarting the laptop without the external monitor all is back as it used to be. The video card in this laptop is a ATI Technologies RV350 [Mobility Radeon 9600 M10] Has anybody an idea how to use the external monitor in order to enable an extended desktop? I have tried to see whether I could change /etc/X/xorg.conf but did not find a way to do this. I hoped fedora 8 would solve this problem, but see below: 2. I have downloaded fedora 8, burned this on a disk and used the disk to install on a desktop. No problem. I took the same disk to my Asus (dual boot with Windows XP) and started up from the disk and chose the option "upgrade an existing system". the system began collecting installed packages end thereafter checking dependencies. about 40% through this the system hangs completely (no mouse action either) and only using the on/off button of the laptop gives any result. B.

2 3

Help in installing Fedora 8
by Miata Red 27 Nov '07

27 Nov '07

I hope someone can give some ideas. I have a Toshiba Portégé 3500 laptop. (P3 1.3GHz, 1 GB of RAM) It is a Tablet PC and has been running XP Pro Tablet Ed. I have been trying to install Fedora for many months already and am not giving up I have successfully installed Fedora 8 on many other PCs and laptops, but this one is a real challenge to me. It is a non-standard PC: no built-in CD-ROM, it uses a proprietary PCMCIA model from Targus made for this model, and special drivers are needed to run it, DOS drivers do exist, but no Linux drivers. I only use it to re-install Windows XP as the Toshiba recovery CDs need it. I do not care for the Tablet PC specific functions, as I use it as a standard laptop. I also have a standard external USB 2.0 CD/DVD-RW, however it will not boot from this but I do have an external FDD and it will boot from this. If I try to boot the Fedora DVD, using the PCMCIA CD-ROM it will get started, but then Anaconda will not recognize the device, and stops and no Linux drivers exists. So I figure I could use the USB CD/DVD-ROM, as I think this will be a valid device for Anaconda. I need specific instructions to create floppies to get a successful Fedora 8 installation. Can anyone help ? Thank you. Denis No virus found in this outgoing message. Checked by AVG Free Edition. Version: 7.5.503 / Virus Database: 269.16.8/1154 - Release Date: 11/27/07 11:40 AM

1 0

hpdv9500
by Joseph F. Shea 24 Nov '07

24 Nov '07

I tried loading Ubuntu 7.10 on to an HP dv9500 laptop (AMD Turion 64 x2 TL-58 1.9Ghz), but could not configure Nvidia card or Broadcom wireless card. (Saw some suggestions for fixing the NVidia card, but need wireless connection to do it). Will Fedora 8 load on this machine without a lot of tweaking?

2 1

Suspend succeed, wake up lost screen
by smartkenny 23 Nov '07

23 Nov '07

Hi, all Fedora 8 on my Acer Aspire 1681 has problem to suspend/wake up. Actually, it suspend successfully, but when wake up, the screen is completely black. The keyboard works still, because the caps lock LED works. I can ssh remote login from other machine, and get the attached dmesg output. I am using 915resolution+i810 drv to support my 1280x800 resolution. I did try intel drv which actually is the default when install Fedora 8, but the problem is when wake up, the screen is also complete black, plus the keyboard doesn't respond. Any suggestion? I hope the dmesg output can help the developers to improve the suspending. Thank. Kenny Linux version 2.6.23.1-49.fc8 (kojibuilder(a)xenbuilder4.fedora.phx.redhat.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Thu Nov 8 21:41:26 EST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000004dee0000 (usable) BIOS-e820: 000000004dee0000 - 000000004deec000 (ACPI data) BIOS-e820: 000000004deec000 - 000000004df00000 (ACPI NVS) BIOS-e820: 000000004df00000 - 0000000050000000 (reserved) BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved) BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved) BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved) 350MB HIGHMEM available. 896MB LOWMEM available. Using x86 segment limits to approximate NX protection Entering add_active_range(0, 0, 319200) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 319200 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 319200 On node 0 totalpages: 319200 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 701 pages used for memmap HighMem zone: 89123 pages, LIFO batch:15 Movable zone: 0 pages used for memmap DMI present. Using APIC driver default ACPI: RSDP 000F62E0, 0014 (r0 ACER ) ACPI: RSDT 4DEE66D8, 0030 (r1 ACER Kestrel 20020806 LTP 0) ACPI: FACP 4DEEBF2C, 0074 (r1 ACER Kestrel 20020806 PTL 50) ACPI: DSDT 4DEE6708, 5824 (r1 ACER Kestrel 20020806 MSFT 100000E) ACPI: FACS 4DEFCFC0, 0040 ACPI: HPET 4DEEBFA0, 0038 (r1 ACER Kestrel 20020806 PTL 0) ACPI: BOOT 4DEEBFD8, 0028 (r1 ACER Kestrel 20020806 LTP 1) ACPI: PM-Timer IO Port: 0x1008 ACPI: HPET id: 0x8086a201 base: 0x0 Allocating PCI resources starting at 60000000 (gap: 50000000:aec10000) swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000 swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000ce000 swsusp: Registered nosave memory region: 00000000000ce000 - 00000000000d0000 swsusp: Registered nosave memory region: 00000000000d0000 - 00000000000dc000 swsusp: Registered nosave memory region: 00000000000dc000 - 0000000000100000 Built 1 zonelists in Zone order. Total pages: 316707 Kernel command line: ro root=LABEL=/1 rhgb quiet Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffb000 (019d0000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c07a8000 soft=c0788000 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1498.768 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1257652k/1276800k available (2184k kernel code, 18184k reserved, 1116k data, 280k init, 359296k highmem) virtual kernel memory layout: fixmap : 0xffc53000 - 0xfffff000 (3760 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc073f000 - 0xc0785000 ( 280 kB) .data : 0xc0622165 - 0xc0739544 (1116 kB) .text : 0xc0400000 - 0xc0622165 (2184 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Calibrating delay using timer specific routine.. 2998.57 BogoMIPS (lpj=1499288) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: afe9f9ff 00100000 00000000 00000000 00000180 00000000 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: After all inits, caps: afe9f1ff 00100000 00000000 00002040 00000180 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 14k freed ACPI: Core revision 20070126 ACPI: setting ELCR to 0200 (from 0440) CPU0: Intel(R) Pentium(R) M processor 1.50GHz stepping 08 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs sizeof(vma)=84 bytes sizeof(page)=32 bytes sizeof(inode)=336 bytes sizeof(dentry)=132 bytes sizeof(ext3inode)=488 bytes sizeof(buffer_head)=56 bytes sizeof(skbuff)=180 bytes sizeof(task_struct)=1552 bytes Booting paravirtualized kernel on bare hardware Time: 21:42:00 Date: 11/23/07 NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd792, last bus=2 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using PIC for interrupt routing ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62 ACPI: PCI Root Bridge [PCI0] (0000:00) Force enabled HPET at base address 0xfed00000 PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH4 GPIO PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs *6) ACPI: PCI Interrupt Link [LNKB] (IRQs *10) ACPI: PCI Interrupt Link [LNKC] (IRQs *6) ACPI: PCI Interrupt Link [LNKD] (IRQs *6) ACPI: PCI Interrupt Link [LNKE] (IRQs *10) ACPI: PCI Interrupt Link [LNKF] (IRQs 10) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 6) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs *10) ACPI: Power Resource [PFN0] (off) ACPI: Power Resource [PFN1] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 9 devices ACPI: ACPI bus type pnp unregistered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default hpet clockevent registered hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 64-bit timers, 14318180 Hz Time: tsc clocksource has been installed. pnp: 00:04: ioport range 0x164e-0x164f has been reserved pnp: 00:04: iomem range 0xfec10000-0xfec1ffff could not be reserved pnp: 00:04: iomem range 0xff800000-0xffbfffff could not be reserved pnp: 00:04: iomem range 0xfff00000-0xffffffff could not be reserved pnp: 00:04: iomem range 0x0-0x9ffff could not be reserved PCI: Bus 3, cardbus bridge: 0000:02:06.0 IO window: 00003000-000030ff IO window: 00003400-000034ff PREFETCH window: 60000000-63ffffff MEM window: 68000000-6bffffff PCI: Bridge: 0000:00:1e.0 IO window: 3000-3fff MEM window: e0200000-e05fffff PREFETCH window: 60000000-65ffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:02:06.0 (0104 -> 0107) ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 2908k freed Simple Boot Flag at 0x37 set to 0x1 apm: BIOS not found. audit: initializing netlink socket (disabled) audit(1195854120.465:1): initialized highmem bounce pool size: 64 pages Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks ksign: Installing public key data Loading keyring - Added public key D5E5FC8EDCF186B6 - User ID: Red Hat, Inc. (Kernel Module GPG key) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:00:02.0 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Transitioning device [FAN0] to D3 ACPI: Transitioning device [FAN0] to D3 ACPI: Fan [FAN0] (off) ACPI: Transitioning device [FAN1] to D3 ACPI: Transitioning device [FAN1] to D3 ACPI: Fan [FAN1] (off) ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THRM] (65 C) isapnp: Scanning for PnP cards... Switched to high resolution mode on CPU 0 isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.102 agpgart: Detected an Intel 855GM Chipset. agpgart: Detected 32636K stolen memory. agpgart: AGP aperture is 128M @ 0xe8000000 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI interrupt for device 0000:00:1f.6 disabled RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize input: Macintosh mouse button emulation as /class/input/input0 Yenta: CardBus bridge found at 0000:02:06.0 [1025:0064] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:06.0, mfunc 0x01a21b22, devctl 0x64 Yenta: ISA IRQ mask 0x08f8, PCI irq 10 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06 pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff cs: IO port probe 0x3000-0x3fff: clean. pcmcia: parent PCI bridge Memory window: 0xe0200000 - 0xe05fffff pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x65ffffff PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input1 cpuidle: using governor menu usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode Magic number: 15:671:753 Freeing unused kernel memory: 280k freed Write protecting the kernel read-only data: 845k Marking TSC unstable due to: TSC halts in idle. Time: hpet clocksource has been installed. ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 10, io mem 0xe0100000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6 PCI: setting IRQ 6 as level-triggered ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 6, io base 0x00001820 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6 ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 6, io base 0x00001840 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 6 ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 6, io base 0x00001860 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected Synaptics Touchpad, model: 1, fw: 5.9, id: 0x126eb1, caps: 0xa04713/0x4000 SCSI subsystem initialized libata version 2.21 loaded. input: SynPS/2 Synaptics TouchPad as /class/input/input2 usb 3-1: new low speed USB device using uhci_hcd and address 2 ata_piix 0000:00:1f.1: version 2.12 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1f.1 to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011810 irq 14 ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011818 irq 15 ata1.00: ATA-6: IC25N080ATMR04-0, MO4OAD4A, max UDMA/100 ata1.00: 156301488 sectors, multi 16: LBA48 usb 3-1: configuration #1 chosen from 1 choice ata1.00: configured for UDMA/100 input: Logitech USB Receiver as /class/input/input3 input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-1 input: Logitech USB Receiver as /class/input/input4 input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.1-1 ata2.00: ATAPI: QSI CD-RW/DVD-ROM SBW242C, UQ81, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA IC25N080ATMR04-0 MO4O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sd 0:0:0:0: [sda] Attached SCSI disk scsi 1:0:0:0: CD-ROM QSI CDRW/DVD SBW242C UQ81 PQ: 0 ANSI: 5 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. audit(1195854126.677:2): enforcing=1 old_enforcing=0 auid=4294967295 security: 8 users, 11 roles, 2359 types, 112 bools, 1 sens, 1024 cats security: 67 classes, 212240 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev sda1, type ext3), uses xattr SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts audit(1195854127.304:3): policy loaded auid=4294967295 sr0: scsi3-mmc drive: 4x/4x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 1:0:0:0: Attached scsi generic sg1 type 5 cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007) iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 input: Power Button (FF) as /class/input/input5 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /class/input/input6 ACPI: Lid Switch [LID] input: Sleep Button (CM) as /class/input/input7 ACPI: Sleep Button (CM) [SLPB] input: PC Speaker as /class/input/input8 input: Video Bus as /class/input/input9 ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no) intel_rng: FWH not detected ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno(a)linux.intel.com> ACPI: Smart Battery System [SMBC]: AC Adapter [AC0] (on-line) ACPI: PCI Interrupt 0000:02:06.3[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10 ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq ipw2200: Copyright(c) 2003-2006 Intel Corporation ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection NET: Registered protocol family 23 ipw2200: Radio Frequency Kill Switch is On: Kill switch must be turned off for wireless networking to work. nsc-ircc, chip->init nsc-ircc, Found chip at base=0x164e nsc-ircc, driver loaded (Dag Brattli) nsc_ircc_open(), can't get iobase of 0x2f8 nsc-ircc, Found chip at base=0x164e nsc-ircc, driver loaded (Dag Brattli) nsc_ircc_open(), can't get iobase of 0x2f8 pnp: Device 00:08 disabled. ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels) ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6 net eth1: device_rename: sysfs_create_symlink failed (-17) udev: renamed network interface eth0 to eth1 ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0 b44.c:v2.0 eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:c0:9f:7f:82:b8 ACPI: PCI Interrupt 0000:02:06.2[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10 ACPI: Smart Battery System [SMBC]: Battery Slot [BAT0] (battery present) firewire_ohci: Added fw-ohci device 0000:02:06.2, OHCI version 1.10 ACPI: Smart Battery System [SMBC]: Battery Slot [BAT1] (battery present) ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 firewire_core: created new fw device fw0 (0 config rom retries, S400) intel8x0_measure_ac97_clock: measured 50388 usecs intel8x0: clocking to 48000 ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.6 to 64 MC'97 0 converters and GPIO not ready (0x1) SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts NET: Registered protocol family 10 lo: Disabled Privacy Extensions ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel(a)redhat.com device-mapper: multipath: version 1.0.5 loaded EXT3 FS on sda1, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda3, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda2, type ext3), uses xattr kjournald starting. Commit interval 5 seconds EXT3 FS on sda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda5, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs Adding 1341388k swap on /dev/sda6. Priority:-1 extents:1 across:1341388k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts IA-32 Microcode Update Driver: v1.14a <tigran(a)aivazian.fsnet.co.uk> ip6_tables: (C) 2000-2006 Netfilter Core Team Clocksource tsc unstable (delta = -86144737 ns) Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) ip_tables: (C) 2000-2006 Netfilter Core Team ADDRCONF(NETDEV_UP): eth0: link is not ready b44: eth0: Link is up at 100 Mbps, full duplex. b44: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ADDRCONF(NETDEV_UP): eth1: link is not ready eth0: no IPv6 routers present audit(1195854165.563:4): audit_pid=2065 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0 SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts SELinux: initialized (dev autofs, type autofs), uses genfs_contexts vboxdrv: Trying to deactivate the NMI watchdog permanently... vboxdrv: Successfully done. ttyS1: LSR safety check engaged! [drm] Initialized drm 1.1.0 20060810 [drm] Initialized i915 1.6.0 20060119 on minor 0 [drm] Initialized i915 1.6.0 20060119 on minor 1 ADDRCONF(NETDEV_UP): eth0: link is not ready ADDRCONF(NETDEV_UP): eth1: link is not ready b44: eth0: Link is up at 100 Mbps, full duplex. b44: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready eth0: no IPv6 routers present ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sr0, type iso9660), uses genfs_contexts eth0: no IPv6 routers present ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sr0, type iso9660), uses genfs_contexts ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sr0, type iso9660), uses genfs_contexts PM: Preparing system for mem sleep Stopping tasks ... done. PM: Entering mem sleep Suspending console(s) sd 0:0:0:0: [sda] Synchronizing SCSI cache sd 0:0:0:0: [sda] Stopping disk ACPI handle has no context! ACPI: PCI interrupt for device 0000:02:06.3 disabled ACPI handle has no context! eth1: Going into suspend... ACPI: PCI interrupt for device 0000:02:04.0 disabled ACPI: PCI interrupt for device 0000:02:02.0 disabled ACPI: PCI interrupt for device 0000:00:1f.6 disabled ACPI: PCI interrupt for device 0000:00:1f.5 disabled ACPI: PCI interrupt for device 0000:00:1f.1 disabled ACPI: PCI interrupt for device 0000:00:1d.7 disabled ACPI: PCI interrupt for device 0000:00:1d.2 disabled ACPI: PCI interrupt for device 0000:00:1d.1 disabled ACPI: PCI interrupt for device 0000:00:1d.0 disabled ipw2200: Unable to load ucode: -22 ipw2200: Unable to load firmware: -22 ipw2200: Failed to up device Disabling non-boot CPUs ... cpufreq: suspend failed to assert current frequency is what timing core thinks it is. Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Back to C! cpufreq: resume failed to assert current frequency is what timing core thinks it is. Force enabled HPET at resume ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.0 to 64 usb usb2: root hub lost power or was reset ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.1 to 64 usb usb3: root hub lost power or was reset ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.2 to 64 usb usb4: root hub lost power or was reset ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1d.7 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1f.1 to 64 ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.6 to 64 PCI: Enabling device 0000:02:02.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6 eth1: Coming out of suspend... PCI: Enabling device 0000:02:04.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt 0000:02:06.3[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10 pnp: Failed to activate device 00:06. pnp: Failed to activate device 00:07. sd 0:0:0:0: [sda] Starting disk ata1.00: ACPI cmd 03/45:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata1.00: ACPI cmd 00/0c:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata1.00: revalidation failed (errno=-5) ata1: failed to recover some devices, retrying in 5 secs ata1.00: ACPI cmd 03/45:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata1.00: ACPI cmd 00/0c:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata1.00: ACPI on devcfg failed the second time, disabling (errno=-5) ata1.00: revalidation failed (errno=1) ata1: failed to recover some devices, retrying in 5 secs ipw2200: ipw2200-bss.fw request_firmware failed: Reason -2 ipw2200: Unable to load firmware: -2 ata2.00: ACPI cmd 03/42:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata2.00: ACPI cmd 00/0c:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata2.00: revalidation failed (errno=-5) ata2: failed to recover some devices, retrying in 5 secs ata1.00: configured for UDMA/100 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA PM: Finishing wakeup. Restarting tasks ... <6>usb 3-1: USB disconnect, address 2 done. usb 3-1: new low speed USB device using uhci_hcd and address 3 usb 3-1: configuration #1 chosen from 1 choice input: Logitech USB Receiver as /class/input/input10 input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-1 input: Logitech USB Receiver as /class/input/input11 input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.1-1 ADDRCONF(NETDEV_UP): eth0: link is not ready b44: eth0: Link is up at 100 Mbps, full duplex. b44: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ata2.00: ACPI cmd 03/42:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata2.00: ACPI cmd 00/0c:00:00:00:a0:ef failed (Emask=0x1 Stat=0x51 Err=0x04) ata2.00: ACPI on devcfg failed the second time, disabling (errno=-5) ata2.00: revalidation failed (errno=1) ata2: failed to recover some devices, retrying in 5 secs ata2.00: configured for UDMA/33 atkbd.c: Unknown key pressed (translated set 2, code 0xa9 on isa0060/serio0). atkbd.c: Use 'setkeycodes e029 <keycode>' to make it known. atkbd.c: Unknown key released (translated set 2, code 0xa9 on isa0060/serio0). atkbd.c: Use 'setkeycodes e029 <keycode>' to make it known. atkbd.c: Unknown key pressed (translated set 2, code 0xa9 on isa0060/serio0). atkbd.c: Use 'setkeycodes e029 <keycode>' to make it known. eth0: no IPv6 routers present atkbd.c: Unknown key released (translated set 2, code 0xa9 on isa0060/serio0). atkbd.c: Use 'setkeycodes e029 <keycode>' to make it known. PM: Preparing system for mem sleep Stopping tasks ... done. PM: Entering mem sleep Suspending console(s) sd 0:0:0:0: [sda] Synchronizing SCSI cache sd 0:0:0:0: [sda] Stopping disk ACPI handle has no context! ACPI: PCI interrupt for device 0000:02:06.3 disabled ACPI handle has no context! eth1: Going into suspend... ACPI: PCI interrupt for device 0000:02:04.0 disabled ACPI: PCI interrupt for device 0000:02:02.0 disabled ACPI: PCI interrupt for device 0000:00:1f.6 disabled ACPI: PCI interrupt for device 0000:00:1f.5 disabled ACPI: PCI interrupt for device 0000:00:1f.1 disabled ACPI: PCI interrupt for device 0000:00:1d.7 disabled ACPI: PCI interrupt for device 0000:00:1d.2 disabled ACPI: PCI interrupt for device 0000:00:1d.1 disabled ACPI: PCI interrupt for device 0000:00:1d.0 disabled Disabling non-boot CPUs ... cpufreq: suspend failed to assert current frequency is what timing core thinks it is. Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Back to C! cpufreq: resume failed to assert current frequency is what timing core thinks it is. Force enabled HPET at resume ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.0 to 64 usb usb2: root hub lost power or was reset ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.1 to 64 usb usb3: root hub lost power or was reset ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1d.2 to 64 usb usb4: root hub lost power or was reset ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1d.7 to 64 PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 6 (level, low) -> IRQ 6 PCI: Setting latency timer of device 0000:00:1f.1 to 64 ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.6 to 64 PCI: Enabling device 0000:02:02.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6 eth1: Coming out of suspend... PCI: Enabling device 0000:02:04.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt 0000:02:06.3[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10 pnp: Failed to activate device 00:06. pnp: Failed to activate device 00:07. ata2.00: configured for UDMA/33 sd 0:0:0:0: [sda] Starting disk ata1.00: configured for UDMA/100 sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA PM: Finishing wakeup. Restarting tasks ... <6>usb 3-1: USB disconnect, address 3 ipw2200: Radio Frequency Kill Switch is On: Kill switch must be turned off for wireless networking to work. done. usb 3-1: new low speed USB device using uhci_hcd and address 4 usb 3-1: configuration #1 chosen from 1 choice input: Logitech USB Receiver as /class/input/input12 input: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-1 input: Logitech USB Receiver as /class/input/input13 input,hiddev96: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.1-1 ADDRCONF(NETDEV_UP): eth0: link is not ready kobject_add failed for vcs63 with -EEXIST, don't try to register things with the same name in the same directory. [<c04f2c7b>] kobject_shadow_add+0x159/0x18b [<c04f2f62>] kobject_set_name+0x2b/0x92 [<c05650d0>] device_add+0x87/0x51a [<c04f2ceb>] kobject_init+0x2f/0x3f [<c0565ae0>] device_create+0x77/0x97 [<c0548ea8>] vcs_make_sysfs+0x34/0x6e [<c054deb4>] con_open+0x6f/0x7c [<c054465a>] tty_open+0x167/0x2b6 [<c0483742>] chrdev_open+0x111/0x14e [<c04cfb36>] selinux_dentry_open+0x59/0x5e [<c0483631>] chrdev_open+0x0/0x14e [<c047f9f5>] __dentry_open+0xd5/0x18c [<c047fb26>] nameidata_to_filp+0x24/0x33 [<c047fb6c>] do_filp_open+0x37/0x3e [<c047f8a6>] get_unused_fd_flags+0x52/0xc5 [<c047fbbb>] do_sys_open+0x48/0xca [<c047fc76>] sys_open+0x1c/0x1e [<c040518a>] syscall_call+0x7/0xb [<c0610000>] xfrm_parse_spi+0x3c/0xc8 ======================= kobject_add failed for vcsa63 with -EEXIST, don't try to register things with the same name in the same directory. [<c04f2c7b>] kobject_shadow_add+0x159/0x18b [<c04f2f62>] kobject_set_name+0x2b/0x92 [<c05650d0>] device_add+0x87/0x51a [<c04f2ceb>] kobject_init+0x2f/0x3f [<c0565ae0>] device_create+0x77/0x97 [<c0548edd>] vcs_make_sysfs+0x69/0x6e [<c054deb4>] con_open+0x6f/0x7c [<c054465a>] tty_open+0x167/0x2b6 [<c0483742>] chrdev_open+0x111/0x14e [<c04cfb36>] selinux_dentry_open+0x59/0x5e [<c0483631>] chrdev_open+0x0/0x14e [<c047f9f5>] __dentry_open+0xd5/0x18c [<c047fb26>] nameidata_to_filp+0x24/0x33 [<c047fb6c>] do_filp_open+0x37/0x3e [<c047f8a6>] get_unused_fd_flags+0x52/0xc5 [<c047fbbb>] do_sys_open+0x48/0xca [<c047fc76>] sys_open+0x1c/0x1e [<c040518a>] syscall_call+0x7/0xb [<c0610000>] xfrm_parse_spi+0x3c/0xc8 ======================= b44: eth0: Link is up at 100 Mbps, full duplex. b44: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready VFS: busy inodes on changed media. VFS: busy inodes on changed media. eth0: no IPv6 routers present

1 0

driver for TP Link WN610G
by Amar 23 Nov '07

23 Nov '07

Hi, Need help with driver for TP Link WN610G wireless network card amar

2 2

support for ati VGA and broadcom wireless cards
by Thilina Buddhika 22 Nov '07

22 Nov '07

Hi, I am using a DELL INSPIRON 6400, with ati radeon x1300 graphics card. I found it difficult to install other linux based OSs due to this VGA. Will i be able to install fedora 8 in my laptop, without any difficulty. Also it has a broadcom wireless card. does fedora 8 supports this ? thanks and regards, buddhika

3 2

ASUS M6000: dual head & upgrade to fedora 8
by dhhb2304 20 Nov '07

20 Nov '07

1 0

T61 monitor
by Peter Lauri 14 Nov '07

14 Nov '07

Hi, I have the Lenovo/IBM T61 with WXGA 14.1 inch screen and Intel Graphics Media Accelerator 945. The max resolution is 1280x800. On my current FC7 installation I cannot get the resolution up to this value. Maximum is 1024x768 :( Any hints of how I can fix this? /Peter

4 7

Problem with Fedora core 8 installer
by Arno 14 Nov '07

14 Nov '07

Hello, When I run the Fedora core 8 installer my laptop hangs with the "running /sbin/loader", I've left my laptop on for over an hour but still nothing is happened. Please help Gr Arno

3 2

FW: Problem with Fedora core 8 installer
by Arno 14 Nov '07

14 Nov '07

Hello, The option you gave me worked very well, my next problem is with the installer, when I run the installdisk check it says the dvd is good, I run the installer, selecting partitions, software etc, and then the installer start installing. After the formatting stuff the installer come with the can't find package error. The only options are retry and reboot. How can this happen while my install-disc is correct. Please help Gr Arno Van: Mohd Zeeshan [mailto:zeehere@gmail.com] Verzonden: Wednesday, November 14, 2007 3:15 AM Aan: Arno Weterings Onderwerp: Re: Problem with Fedora core 8 installer When you get the first menu to install/upgrade fedora, press TAB and append these lines to the existing line floppy.allowed_mask=0 clocksource=acpi_pm Also if you have many extra non-standard software installed on your last Fedora 7, that yum will not find on its standard repositories, then also it will hang on resolving dependencies at later stage. Therefore before upgrading, remove all extras. I have faced all these issues myself. Thanks. Zee. On Nov 14, 2007 1:30 AM, Arno Weterings <aweterings(a)gmail.com> wrote: Hello, When I run the Fedora core 8 installer my laptop hangs with the "running /sbin/loader", I've left my laptop on for over an hour but still nothing is happened. Please help Gr Arno _______________________________________________ Fedora-laptop-list mailing list Fedora-laptop-list(a)redhat.com http://www.redhat.com/mailman/listinfo/fedora-laptop-list -- ::Zeeshan::

1 0

T61 architecture
by Peter Lauri 09 Nov '07

09 Nov '07

Hi, I am a bit confused. Some sites on internet I found refer to a x86_64 installation and others to a i386 installation. Can both be done? What is recommended in that case? I have just noticed that the x86_64 arch is less supported by other software? /Peter

4 4

FC 8
by Al Thompson 09 Nov '07

09 Nov '07

I see that Core 8 is out, or will be very shortly. I have Core7 installed, and up-to-date. My question is this: If I continue to update my FC7 installation, is there any advantage to installing FC8? What would the differences be, if any?

2 1

Re: Dell Latitude 131L and Fedora 8
by Al Thompson 05 Nov '07

05 Nov '07

----- Original Message ---- From: Fabio Tust <fabiotust(a)gmail.com> To: fedora-laptop-list(a)redhat.com Sent: Monday, November 5, 2007 12:14:12 PM Subject: Dell Latitude 131L and Fedora 8 >I have a Dell 131L laptop running Fedora 7 x64, but the wifi don't work. My wifi is a Broadcom and >the driver is bcm43xx. I tried various tutorials on de web, using ndiswrapper or fwcutter and winxp >drivers, but don't getting sucess. I'm having the same trouble with Fedora Core 7 on a Compaq laptop with a Broadcom internal wifi. I can actually get as far as being able to configure it using iwconfig, and it will even scan for APs, and give me the results. However, I cannot ping out of it, and the GUI steadfastly refuses to see it. On a whim, I tried a USB wifi device, with the exact same results, so maybe it's not specific to the Broadcom device. If you find an answer, post it here!

2 1

Dell Latitude 131L and Fedora 8
by Fabio Tust 05 Nov '07

05 Nov '07

Hello everybody, I have a Dell 131L laptop running Fedora 7 x64, but the wifi don't work. My wifi is a Broadcom and the driver is bcm43xx. I tried various tutorials on de web, using ndiswrapper or fwcutter and winxp drivers, but don't getting sucess. I'm have tested with ubuntu 7.10 and the wifi works fine, but i received a warning like "the driver have a restrict license". I don't like ubuntu, so anyone knows if the F8 is better for wifi cards of laptops? Forgive my mistakes in English, I am Brazilian and my English is not widely used Thank's Fabio Tust

1 0

No more sound
by J Cole 01 Nov '07

01 Nov '07

Hi, In the last couple of months my sound has gone. I have updated Alsa, Kernel, Bios with no avail. My Laptop is a NEC M400 Here is a link to my data: http://pastebin.ca/756324 or ALSA Audio Debug v0.1.0 - Wed Oct 31 21:03:07 WST 2007 http://alsa.opensrc.org/aadebug http://www.gnu.org/licenses/gpl.txt Kernel ---------------------------------------------------- Linux nec 2.6.23.1-10.fc7 #1 SMP Fri Oct 19 15:39:08 EDT 2007 i686 i686 i386 GNU/Linux Loaded Modules -------------------------------------------- snd_intel8x0m 16717 0 snd_usb_audio 74305 0 snd_usb_lib 16961 1 snd_usb_audio snd_rawmidi 21185 1 snd_usb_lib snd_hwdep 10309 1 snd_usb_audio snd_seq_dummy 6725 0 snd_intel8x0 30429 0 snd_ac97_codec 91749 2 snd_intel8x0m,snd_intel8x0 snd_seq_oss 29889 0 snd_seq_midi_event 9665 1 snd_seq_oss snd_seq 44721 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 9933 4 snd_rawmidi,snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 38337 0 snd_mixer_oss 16577 1 snd_pcm_oss snd_pcm 64069 5 snd_intel8x0m,snd_usb_audio,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_timer 20421 2 snd_seq,snd_pcm snd 43205 13 snd_intel8x0m,snd_usb_audio,snd_rawmidi,snd_hwdep,snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer snd_page_alloc 11209 3 snd_intel8x0m,snd_intel8x0,snd_pcm Modprobe Conf --------------------------------------------- options snd cards_limit=8 alias snd-card-0 snd-intel8x0 options snd-intel8x0 index=0 alias snd-card-7 snd-usb-audio options snd-usb-audio index=7 Proc Asound ----------------------------------------------- Advanced Linux Sound Architecture Driver Version 1.0.14 (Fri Jul 20 09:12:58 2007 UTC). --- no soundcards --- 2: : timer 3: : sequencer Client info cur clients : 3 peak clients : 3 max clients : 192 Client 0 : "System" [Kernel] Port 0 : "Timer" (Rwe-) Port 1 : "Announce" (R-e-) Connecting To: 15:0 Client 14 : "Midi Through" [Kernel] Port 0 : "Midi Through Port-0" (RWe-) Client 15 : "OSS sequencer" [Kernel] Port 0 : "Receiver" (-we-) Connected From: 0:1 Dev Snd --------------------------------------------------- seq timer CPU ------------------------------------------------------- model name : Genuine Intel(R) CPU 2.80GHz cpu MHz : 1596.000 RAM ------------------------------------------------------- MemTotal: 1002448 kB SwapTotal: 983032 kB Hardware -------------------------------------------------- 00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03) Cheers Jason

1 0

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

laptop November 2007