Upgrade attempt
by Arne Chr. Jorgensen
hi,
Attempted upgrading with F7_x64 on the F7_i386. 15 packaged installed.
It wrote a new bootloader, didn't save the old kernel, and ended up in the
reported kernel panic, as it couldn't find Volgroup... and filesystem.
Attempting to upgrade back to F7_i386 didn't work. Perhaps because the
kernel name/version was the same ?
Now, any suggestions ?
//ARNE
---------------------------------
Be a better Heartthrob. Get better relationship answers from someone who knows.
Yahoo! Answers - Check it out.
16 years, 7 months
- 1
- 0
My hardware....
by Arne Chr. Jorgensen
hi,
It did boot up with the F7_i386, have to hit the power button a couple of times in
order to have it boot the kernel. ( for some reasons it stops during bootup )
Trouble:
- it doesn't get up the right X-driver
- impossible to get wireless configured or working
- the display will not come back up after hibernation
For reference, the tag on the back says:
Presario 6500
P/N: GP645EA
Btw: The HP spec seem to say that it is a Broadcom 4321 device,
not a 4310 as listed below.
//ARNE
And more, anyway here is what lspci -v reports:
00:00.0 RAM memory: nVidia Corporation Unknown device 0547 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [dc] HyperTransport: MSI Mapping
00:01.0 ISA bridge: nVidia Corporation Unknown device 0548 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
00:01.1 SMBus: nVidia Corporation Unknown device 0542 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 3080 [size=64]
Region 4: I/O ports at 3040 [size=64]
Region 5: I/O ports at 3000 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.2 RAM memory: nVidia Corporation Unknown device 0541 (rev a2)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:01.3 Co-processor: nVidia Corporation Unknown device 0543 (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 11
Region 0: Memory at f6200000 (32-bit, non-prefetchable) [size=512K]
00:02.0 USB Controller: nVidia Corporation Unknown device 055e (rev a2) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6486000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation Unknown device 055f (rev a2) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f6489000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 USB Controller: nVidia Corporation Unknown device 055e (rev a2) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f6487000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.1 USB Controller: nVidia Corporation Unknown device 055f (rev a2) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f6489400 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 IDE interface: nVidia Corporation Unknown device 0560 (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: Unknown device f03c:30cf
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 30c0 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 Audio device: nVidia Corporation Unknown device 055c (rev a1)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f6480000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping
00:08.0 PCI bridge: nVidia Corporation Unknown device 0561 (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f6100000-f61fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [b8] Subsystem: nVidia Corporation Unknown device cb84
Capabilities: [8c] HyperTransport: MSI Mapping
00:09.0 IDE interface: nVidia Corporation Unknown device 0550 (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 30f0 [size=8]
Region 1: I/O ports at 30e4 [size=4]
Region 2: I/O ports at 30e8 [size=8]
Region 3: I/O ports at 30e0 [size=4]
Region 4: I/O ports at 30d0 [size=16]
Region 5: Memory at f6484000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] #12 [0010]
Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping
00:0a.0 Ethernet controller: nVidia Corporation Unknown device 054c (rev a2)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f6488000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 30f8 [size=8]
Region 2: Memory at f6489c00 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at f6489800 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3 Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping
00:0c.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=05, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f2000000-f3ffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 2, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:0d.0 PCI bridge: nVidia Corporation Unknown device 0563 (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: f6000000-f60fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Subsystem: nVidia Corporation Unknown device 0000
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <512ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
Slot: Number 3, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq+
Slot: AttnInd Off, PwrInd On, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
00:12.0 VGA compatible controller: nVidia Corporation Unknown device 0531 (rev a2) (prog-if 00 [VGA])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f4000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at 88000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=8
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [f0] #0f [0010]
02:05.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f6100000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME+
02:05.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 7
Region 0: Memory at f6100800 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:05.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 12)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 11
Region 0: Memory at f6100c00 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:05.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 11
Region 0: Memory at f6101000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:05.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
Subsystem: Hewlett-Packard Company Unknown device 30cf
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 11
Region 0: Memory at f6101400 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
03:00.0 Network controller: Broadcom Corporation BCM4310 UART (rev 02)
Subsystem: Hewlett-Packard Company Unknown device 1371
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f6000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Vendor Specific Information
Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
---------------------------------
Ready for the edge of your seat? Check out tonight's top picks on Yahoo! TV.
16 years, 7 months
- 1
- 0
Fedora install on Pressario V6000
by Arne Chr. Jorgensen
hi,
I got no response on my last input, as told - I have tried to install F7-86_64,
which didn't lead anywhere.
The following is the last lines that I have written down ( actually, from F7.90-86_64 this time,
while
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel(a)redhat.com
Reading all physical volumes. This may take a while...
No volume groups found
Volume group "VolGroup00" not found
Unable to access resume device (/dev/VolGroup00/LogVol01)
mount: could not find filesystem '/dev/root'
setuproot: moving /dev failed: No such file or directory
setuproot: error mounting /proc: No such file or directory
setuproot: error mounting /sys: No such file or directory
switchroot: mount failed: No such file or directory
Kernel panic - not syncing: Attempted to kill init!
--------------
Any clues ? Tried rescue, checked filesystem, and it seems to be there. Checked Grub, and it
seems like it is given the correctly kernel parameters.
At the moment, I am trying a fresh install of F7_i386 again. Wanting to see if it may be upgraded
by the F7_x64 DVD.
Is there nobody checking these distrobutions for errors ??
- like the F7_i386 will fail any install in textmode
- if testing DVD,CD - it will fail to find any install media, forced to power off, start
over again. Oh...there are just too much....
Any idea what is happening in the situation above ?
I'll supply some more info about the hardware, if I can get this thing to communicate.
//ARNE
---------------------------------
Yahoo! oneSearch: Finally, mobile search that gives answers, not web links.
16 years, 7 months
- 1
- 0
Trouble...trouble...trouble...
by Arne Chr. Jorgensen
hi,
YES, - I should probably check this list archives first - but I have checked everywhere, so - I dive right into it:
Computer: Compaq Pressario V6000 ( actually bought a HP, but was given
this as replacement )
1. Current status:
- Fedora7_x64 will not boot up after install. Kernel panic, can't access resume
device ( /dev/VolGroup00/LogVol01).
Then setroot fails: can't find /dev/root
can't mount /dev ../proc.. /sys.....
Kernel panic - not syncing: Attempted to kill init !
Kernel alive.
( have not been able to figure out the cause when trying to boot up rescue mode)
2. Previous attempts:
- boots up and run OpenSuse _x64
- boots up and fun Fedora7_i386 with some trouble - it will freeze up. but hitting
power off button some seconds, get it continue up the bootup process.
- did boot up with Fedora7_64 with ZEN....
( but I would like to have it running Fedora7_64 ... so I am back attempting
doing that )
3. Confused:
- I don't know what did happen, but perhaps it was with ZEN? I wonder if it
did communicate wireless ? Else this is the real obstacle. I can't bring up the wireless ethernet. ( the reason for a new purchase of hardware )
- Not sure about this, but... I did shrink the disk under Windows Vista, and installed Fedora7_64, and believe I had it running - except the problems
with wireless, and some other settings. The trouble told at section 1 above,
did seem to happen when I tried to repeat the install ?
Any suggestions ???
//ARNE
---------------------------------
Moody friends. Drama queens. Your life? Nope! - their life, your story.
Play Sims Stories at Yahoo! Games.
16 years, 7 months
- 1
- 0
problem with live CD on Dell Inspiron 640m
by shaolin.xie
I tried two live CDs, "Fedora 7 Live i686" and "Fedora 7 KDE Live i686",
both burned from ISO image.
Booting from CDROM, the system halted just before starting the kernel.
follows is what I see from the screen:
"Loading vmlinuz..........................
Loading initrz..........................
Ready..
Uncompressing kernel image .... Ok,,start the kernel ...."
And then,,,nothing happens.
My laptop is Dell Inspiron 640m, CPU is Intel T2080,,,
What is wrong with my laptop ? Any one can share his experience or offer
some suggestion ?
Best Regarts.
Shaolin Xie
16 years, 7 months
- 2
- 1