liveusb-creator February 2009

liveusb-creator@lists.fedorahosted.org

4 participants
9 discussions

Fedora core 10, booting from IBM thinkpad x40
by Dave Pawson 12 Mar '09

12 Mar '09

Burned (loaded?) a 16Gb memory stick, no problem. #Eventually, F12 whilst booting shows the boot selector on my Thinkpad, loaded with Windows xp. When it went to boot from there, I got a message about not being a bootable... ?device? Unsure of the actual wording? Looked at http://syslinux.zytor.com/doc/usbkey.txt Couple of questions please? " For example, if your device reports when inserted into a Linux system: usb-storage: device found at 4 Vendor: 32MB Model: HardDrive Rev: 1.88 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sda: 64000 512-byte hdwr sectors (33 MB) ... you would have 64000/(64*32) = 31.25 cylinders; round down to 31. " What command shows that info please? [root@marge ~]# fdisk -l /dev/sdd Disk /dev/sdd: 16.1 GB, 16131293184 bytes 25 heads, 25 sectors/track, 50410 cylinders Units = cylinders of 625 * 512 = 320000 bytes Disk identifier: 0x04030201 Device Boot Start End Blocks Id System /dev/sdd1 4 50411 15752192 b W95 FAT32 I'm unsure if this tells me the same information or not? Any guidance appreciated. regards -- Dave Pawson XSLT XSL-FO FAQ. Docbook FAQ. http://www.dpawson.co.uk

2 1

Accessing data outside persistent storage
by Mayank Sharma 12 Mar '09

12 Mar '09

Hi, Thanks for writing this wonderful little utility. Works as advertised. But is there any means of accessing the data on the drive, that wasn't zapped by the installer, from within the USBized Live Fedora? Thanks.

3 2

"Stale NFS Handler"
by Thomas King 12 Mar '09

12 Mar '09

I have looked for any other reports on this particular issue and cannot find any. Please point me to the correct workaround if it exists. I've set up a liveUSB key for Fedora 9 and Fedora 10 on a 4GB USB key with a 2GB persistent overlay using the LiveUSB Creator. After running _some_ updates (nothing big, around 50MB) and changing some configurations, I begin getting an error for some files: "Stale NFS Handler". The file will not open. In this past trial, I tried opening /etc/resolv.conf because I was getting an IP address assigned via DHCP; before running updates, I could ping inside and outside the network. After running updates, it would not ping anything using the FQDN, prompting me to look at the /etc/resolv.conf file which threw the stale NFS handler error. This is merely an example since I've had other files unrelated to networking to throw the same error. Are there any workarounds for this? Thanks! Tom King ------- "Concern for man and his fate must always form the chief interest of all technical endeavors. Never forget this in the midst of your diagrams and equations." --Albert Einstein

2 1

po/es.po
by Transifex System User 21 Feb '09

21 Feb '09

po/es.po | 212 ++++++++++++++++++++++++++++++++++----------------------------- 1 file changed, 115 insertions(+), 97 deletions(-) New commits: commit 71258e92b6c2dab05538adb4f56e8926090e2f9d Author: Domingo Becker <domingobecker(a)gmail.com> Date: Sat Feb 21 04:02:56 2009 +0000 updated Spanish translation Transmitted-via: Transifex (translate.fedoraproject.org) diff --git a/po/es.po b/po/es.po index 45fdb3a..fe4717c 100644 --- a/po/es.po +++ b/po/es.po @@ -2,74 +2,48 @@ msgid "" msgstr "" "Project-Id-Version: liveusb-creator\n" "Report-Msgid-Bugs-To: \n" -"POT-Creation-Date: 2008-09-24 03:30+0000\n" -"PO-Revision-Date: 2008-09-24 10:18-0300\n" +"POT-Creation-Date: 2009-02-21 01:51+0000\n" +"PO-Revision-Date: 2009-02-21 01:58-0300\n" "Last-Translator: Domingo Becker <domingobecker(a)gmail.com>\n" "Language-Team: Fedora Spanish <fedora-trans-es(a)redhat.com>\n" "MIME-Version: 1.0\n" "Content-Type: text/plain; charset=UTF-8\n" "Content-Transfer-Encoding: 8bit\n" "X-Poedit-Language: Spanish\n" +"Plural-Forms: nplurals=2; plural=(n != 1);\n" -#: ../liveusb/__init__.py:35 +#: ../liveusb/__init__.py:42 msgid "You must run this application as root" msgstr "Debe ejecutar esta aplicación como root" -#: ../liveusb/gui.py:68 +#: ../liveusb/gui.py:74 #, python-format msgid "Unknown release: %s" msgstr "Versión desconocida: %s" -#: ../liveusb/gui.py:72 +#: ../liveusb/gui.py:78 #, python-format msgid "Downloading %s..." msgstr "Descargando %s..." -#: ../liveusb/gui.py:151 -msgid "Verifying filesystem..." -msgstr "Verificando sistema de archivo..." - -#: ../liveusb/gui.py:154 +#: ../liveusb/gui.py:173 msgid "Error: Cannot set the label or obtain the UUID of your device. Unable to continue." msgstr "Error: No se pudo etiquetar u obtener el UUID de su dispositivo. No se puede continuar." -#: ../liveusb/gui.py:163 -msgid "Verifying SHA1 of LiveCD image..." -msgstr "Verificando SHA1 de la imágen de CD Vivo..." - -#: ../liveusb/gui.py:165 -msgid "Error: The SHA1 of your Live CD is invalid. You can run this program with the --noverify argument to bypass this verification check." -msgstr "Error: El SHA1 de su CD Vivo es inválido. Debe ejecutar este programa con el argumento --noverify para omitir este chequeo de verificación." - -#: ../liveusb/gui.py:176 -msgid "Extracting live image to USB device..." -msgstr "Extrayendo la imágen viva en el dispositivo USB..." - -#: ../liveusb/gui.py:179 -#, python-format -msgid "Creating %d Mb persistent overlay..." -msgstr "Creando %d Mb de overlay persistente..." - -#: ../liveusb/gui.py:182 -msgid "Configuring and installing bootloader..." -msgstr "Configurando e instalando el gestor de arranque..." - -#: ../liveusb/gui.py:186 +#: ../liveusb/gui.py:203 #, python-format msgid "Complete! (%s)" msgstr "¡Completo! (%s)" -#: ../liveusb/gui.py:189 -#: ../liveusb/gui.py:192 +#: ../liveusb/gui.py:207 msgid "LiveUSB creation failed!" msgstr "La creación del USB Vivo falló." -#: ../liveusb/gui.py:317 -#, python-format -msgid "Persistent Storage (%d Mb)" -msgstr "Almacenamiento Persistente (%d Mb)" +#: ../liveusb/gui.py:353 +msgid "Persistent Storage" +msgstr "Almacenamiento Persistente" -#: ../liveusb/gui.py:335 +#: ../liveusb/gui.py:376 msgid "" "Your device already contains a LiveOS.\n" "If you continue, this will be overwritten." @@ -77,47 +51,43 @@ msgstr "" "Su dispositivo ya contiene un SO Vivo.\n" "Si continua, se sobreescribirá." -#: ../liveusb/gui.py:338 +#: ../liveusb/gui.py:379 msgid "Warning: Creating a new persistent overlay will delete your existing one." msgstr "Advertencia: La creación de un overlay persistente borrará el actual existente." -#: ../liveusb/gui.py:340 +#: ../liveusb/gui.py:381 msgid "Press 'Create Live USB' again if you wish to continue." msgstr "Presione 'Crear USB Vivo' de nuevo si desea continuar." -#. The user has confirmed that they wish to overwrite their -#. existing Live OS. Here we delete it first, in order to -#. accurately calculate progress. -#: ../liveusb/gui.py:350 -msgid "Removing existing Live OS..." -msgstr "Eliminando el SO Vivo existente..." - -#: ../liveusb/gui.py:384 +#: ../liveusb/gui.py:428 msgid "Download complete!" msgstr "¡Descarga completa!" -#: ../liveusb/gui.py:388 +#: ../liveusb/gui.py:432 msgid "Download failed: " msgstr "Falló la descarga:" -#: ../liveusb/gui.py:389 +#: ../liveusb/gui.py:433 msgid "You can try again to resume your download" msgstr "Puede intentar de nuevo reasumir la descarga" -#: ../liveusb/gui.py:393 +#: ../liveusb/gui.py:437 msgid "Select Live ISO" msgstr "Seleccione ISO Vivo" -#: ../liveusb/gui.py:400 +#: ../liveusb/gui.py:444 msgid "Sorry, I'm having trouble encoding the filename of your livecd. You may have better luck if you move your ISO to the root of your drive (ie: C:\\)" msgstr "Lo siento, se está teniendo problemas con la codificación del nombre de archivo de su cd vivo. Puede tener mejor suerte si mueve su ISO a la raíz de su disco (ie: C:\\)" -#: ../liveusb/gui.py:405 -#, python-format -msgid "ISO selected: %s" -msgstr "ISO seleccionado: %s" +#: ../liveusb/gui.py:450 +msgid "selected" +msgstr "seleccionado" + +#: ../liveusb/creator.py:135 +msgid "Setting up OLPC boot file..." +msgstr "Configurando un archivo OLPC de arranque..." -#: ../liveusb/creator.py:146 +#: ../liveusb/creator.py:188 #, python-format msgid "" "There was a problem executing the following command: `%s`\n" @@ -126,11 +96,23 @@ msgstr "" "Hubo un problema al ejecutar el siguiente comando: `%s`\n" "Un log del error más detallado se escribió en 'liveusb-creator.log'" -#: ../liveusb/creator.py:183 +#: ../liveusb/creator.py:195 +msgid "Verifying SHA1 of LiveCD image..." +msgstr "Verificando SHA1 de la imágen de CD Vivo..." + +#: ../liveusb/creator.py:217 +msgid "Error: The SHA1 of your Live CD is invalid. You can run this program with the --noverify argument to bypass this verification check." +msgstr "Error: El SHA1 de su CD Vivo es inválido. Debe ejecutar este programa con el argumento --noverify para omitir este chequeo de verificación." + +#: ../liveusb/creator.py:223 +msgid "Unknown ISO, skipping checksum verification" +msgstr "ISO desconocido, omitiendo la verificación de suma" + +#: ../liveusb/creator.py:235 msgid "Not enough free space on device." msgstr "No hay suficiente espacio libre en el dispositivo." -#: ../liveusb/creator.py:184 +#: ../liveusb/creator.py:236 #, python-format msgid "" "\n" @@ -139,62 +121,100 @@ msgstr "" "\n" "%dMB ISO + %dMB overlay > %dMB espacio libre" -#: ../liveusb/creator.py:190 -#, python-format -msgid "Creating %sMB persistent overlay" -msgstr "Creando un overlay persistente de %s MB" +#: ../liveusb/creator.py:242 +msgid "Creating" +msgstr "Creando" + +#: ../liveusb/creator.py:243 +msgid "persistent overlay" +msgstr "overlay persistente" -#: ../liveusb/creator.py:226 +#: ../liveusb/creator.py:275 +msgid "Removing existing Live OS" +msgstr "Eliminando el SO Vivo existente" + +#: ../liveusb/creator.py:284 #, python-format msgid "Unable to remove previous LiveOS: %s" msgstr "No se pudo borrar el SO Vivo previo: %s" -#: ../liveusb/creator.py:257 +#: ../liveusb/creator.py:315 #, python-format msgid "Cannot find device %s" msgstr "No se pudo encontrar el dispositivo %s" -#: ../liveusb/creator.py:306 +#: ../liveusb/creator.py:334 +msgid "Resetting MBR..." +msgstr "Reseteando MBR..." + +#: ../liveusb/creator.py:382 msgid "Unable to find any USB drives" msgstr "No se pudo encontrar ninguna unidad USB" -#: ../liveusb/creator.py:328 +#: ../liveusb/creator.py:405 #, python-format msgid "Filesystem for %s unknown!" msgstr "¡El sistema de archivo de %s es desconocido!" -#: ../liveusb/creator.py:329 +#: ../liveusb/creator.py:406 msgid "device" msgstr "dispositivo" -#: ../liveusb/creator.py:341 +#: ../liveusb/creator.py:418 #, python-format msgid "Unable to mount device: %s" msgstr "No se pudo montar el dispositivo: %s" -#: ../liveusb/creator.py:375 +#: ../liveusb/creator.py:450 +#: ../liveusb/creator.py:677 +msgid "Verifying filesystem..." +msgstr "Verificando sistema de archivo..." + +#: ../liveusb/creator.py:453 #, python-format msgid "Unknown filesystem for %s. Your device may need to be reformatted." msgstr "%s tiene un sistema de archivo desconocido. Su dispositivo puede necesitar ser formateado." -#: ../liveusb/creator.py:378 +#: ../liveusb/creator.py:456 #, python-format msgid "Unsupported filesystem: %s" msgstr "Sistema de archivos no soportado: %s" -#: ../liveusb/creator.py:405 +#: ../liveusb/creator.py:480 +msgid "Your MBR appears to be blank" +msgstr "Su MBR parece estar en blanco" + +#: ../liveusb/creator.py:485 +#: ../liveusb/creator.py:712 +msgid "Extracting live image to USB device..." +msgstr "Extrayendo la imágen viva en el dispositivo USB..." + +#: ../liveusb/creator.py:491 msgid "Unable to find LiveOS on ISO" msgstr "No se pudo encontrar un SO Vivo en el ISO" -#: ../liveusb/creator.py:477 +#: ../liveusb/creator.py:503 +#: ../liveusb/creator.py:720 +msgid "Wrote to device at" +msgstr "Se escribió al dispositivo en" + +#: ../liveusb/creator.py:516 +msgid "Installing bootloader..." +msgstr "Instalando el gestor de arranque..." + +#: ../liveusb/creator.py:553 +msgid "Verifying ISO MD5 checksum" +msgstr "Verificando la suma MD5 del ISO" + +#: ../liveusb/creator.py:673 msgid "Unable to find any removable devices" msgstr "No se pudo encontrar ninguna unidad removible" -#: ../liveusb/creator.py:484 +#: ../liveusb/creator.py:681 msgid "Make sure your USB key is plugged in and formatted with the FAT filesystem" msgstr "Asegúrese de que su unidad USB está conectado y formateado con el sistema de archivo FAT" -#: ../liveusb/creator.py:487 +#: ../liveusb/creator.py:684 #, python-format msgid "" "Unsupported filesystem: %s\n" @@ -203,82 +223,80 @@ msgstr "" "Sistema de archivo no soportado: %s\n" "Por favor, respalde y de formato a su disco USB con el sistema de archivos FAT." -#: ../liveusb/creator.py:563 -#, python-format -msgid "Cannot find '%s'. Make sure to extract the entire liveusb-creator zip file before running this program." -msgstr "No se pudo encontrar '%s'. Asegúrese de extraer el archivo zip liveusb-creator integramente antes de ejecutar este programa." +#: ../liveusb/creator.py:726 +msgid "Installing bootloader" +msgstr "Instalando el gestor de arranque" + +#: ../liveusb/creator.py:770 +msgid "Cannot find" +msgstr "No se pudo encontrar" + +#: ../liveusb/creator.py:771 +msgid "Make sure to extract the entire liveusb-creator zip file before running this program." +msgstr "Asegúrese de extraer el archivo zip liveusb-creator integramente antes de ejecutar este programa." -#: ../liveusb/linux_dialog.py:98 #: ../liveusb/windows_dialog.py:104 msgid "Fedora LiveUSB Creator" msgstr "Creador de USB Vivo de Fedora" -#: ../liveusb/linux_dialog.py:99 #: ../liveusb/windows_dialog.py:105 msgid "This button will begin the LiveUSB creation process. This entails optionally downloading a release (if an existing one wasn't selected), extracting the ISO to the USB device, creating the persistent overlay, and installing the bootloader." msgstr "Este botón iniciará el proceso de creación de USB Vivo. Esto incluye descargar opcionalmente una versión (si no se seleccionó alguna), extraer el ISO en el dispositivo USB, crear el overlay persistente e instalar el gestor de arranque." -#: ../liveusb/linux_dialog.py:100 #: ../liveusb/windows_dialog.py:106 msgid "Create Live USB" msgstr "Crear USB Vivo" -#: ../liveusb/linux_dialog.py:101 #: ../liveusb/windows_dialog.py:107 msgid "This is the status console, where all messages get written to." msgstr "Esta es la consola de estado, donde se escribirán todos los mensajes." -#: ../liveusb/linux_dialog.py:102 #: ../liveusb/windows_dialog.py:108 msgid "This is the progress bar that will indicate how far along in the LiveUSB creation process you are" msgstr "Esta es la barra de progreso que indicará dónde estamos a lo largo de la creación del USB Vivo" -#: ../liveusb/linux_dialog.py:103 #: ../liveusb/windows_dialog.py:109 msgid "If you do not select an existing Live CD, the selected release will be downloaded for you." msgstr "Si no selecciona un CD Vivo esistente, la versión seleccionada se descargará para Ud." -#: ../liveusb/linux_dialog.py:104 #: ../liveusb/windows_dialog.py:110 msgid "Download Fedora" msgstr "Descargar Fedora" -#: ../liveusb/linux_dialog.py:105 #: ../liveusb/windows_dialog.py:111 msgid "or" msgstr "o" -#: ../liveusb/linux_dialog.py:106 #: ../liveusb/windows_dialog.py:112 msgid "This button allows you to browse for an existing Live CD ISO that you have previously downloaded. If you do not select one, a release will be downloaded for you automatically." msgstr "Este botón le permite navegar en búsqueda de un ISO de CD Vivo que haya descargado previamente. Si no seleccionó alguno, se descargará una versión automáticamente." -#: ../liveusb/linux_dialog.py:107 #: ../liveusb/windows_dialog.py:113 msgid "Use existing Live CD" msgstr "Usar un CD Vivo existente" -#: ../liveusb/linux_dialog.py:108 #: ../liveusb/windows_dialog.py:114 msgid "Browse" msgstr "Examinar" -#: ../liveusb/linux_dialog.py:110 #: ../liveusb/windows_dialog.py:116 msgid "This is the USB stick that you want to install your Live CD on. This device must be formatted with the FAT filesystem." msgstr "Este es el disco USB en donde quiere instalar su CD Vivo. Su formato debe ser FAT." -#: ../liveusb/linux_dialog.py:112 +#: ../liveusb/windows_dialog.py:117 +msgid "Target Device" +msgstr "Dispositivo Destino" + #: ../liveusb/windows_dialog.py:118 msgid "By allocating extra space on your USB stick for a persistent overlay, you will be able to store data and make permanent modifications to your live operating system. Without it, you will not be able to save data that will persist after a reboot." msgstr "Asignando espacio extra en un disco USB para un overlay persistente, podrá almacenar datos y hacer modificaciones permanentes al sistema operativo vivo. Sin eso, no podrá guardar los cambios para que estén disponibles en el próximo arranque." -#: ../liveusb/linux_dialog.py:113 #: ../liveusb/windows_dialog.py:119 msgid "Persistent Storage (0 Mb)" msgstr "Almacenamiento Persistente (0 MB)" -#: ../liveusb/windows_dialog.py:117 -msgid "Target Device" -msgstr "Dispositivo Destino" +#~ msgid "Creating %d Mb persistent overlay..." +#~ msgstr "Creando %d Mb de overlay persistente..." +#~ msgid "Persistent Storage (%d Mb)" +#~ msgstr "Almacenamiento Persistente (%d Mb)"

1 0

po/de.po
by Transifex System User 19 Feb '09

19 Feb '09

po/de.po | 133 +++++++++++++++++++++++++++++---------------------------------- 1 file changed, 63 insertions(+), 70 deletions(-) New commits: commit 9feb27ccce191f1a497628dd5a4d7cb8ea590570 Author: Fabian Affolter <fabian(a)bernewireless.net> Date: Thu Feb 19 10:16:15 2009 +0000 Updated German translation Transmitted-via: Transifex (translate.fedoraproject.org) diff --git a/po/de.po b/po/de.po index 4194fae..8a4afbf 100644 --- a/po/de.po +++ b/po/de.po @@ -1,15 +1,15 @@ # German translation of liveusb-creator # Copyright (C) 2008 liveusb-creator # This file is distributed under the same license as the liveusb-creator package. -# Fabian Affolter <fab(a)fedoraproject.org>, 2008,2009. +# Fabian Affolter <fab(a)fedoraproject.org>, 2008-2009. # Marcus Nitzschke <marcusni(a)gmx.de>, 2008. # msgid "" msgstr "" "Project-Id-Version: liveusb-creator\n" "Report-Msgid-Bugs-To: \n" -"POT-Creation-Date: 2008-10-22 13:43+0000\n" -"PO-Revision-Date: 2009-01-11 00:43+0100\n" +"POT-Creation-Date: 2009-02-19 01:52+0000\n" +"PO-Revision-Date: 2009-02-19 11:10+0100\n" "Last-Translator: Fabian Affolter <fab(a)fedoraproject.org>\n" "Language-Team: German <fedora-trans-de(a)redhat.com>\n" "MIME-Version: 1.0\n" @@ -22,35 +22,34 @@ msgstr "" msgid "You must run this application as root" msgstr "Sie müssen diese Anwendung als root ausführen." -#: ../liveusb/gui.py:69 +#: ../liveusb/gui.py:74 #, python-format msgid "Unknown release: %s" msgstr "Unbekannte Version: %s" -#: ../liveusb/gui.py:73 +#: ../liveusb/gui.py:78 #, python-format msgid "Downloading %s..." msgstr "Herunterladen %s ..." -#: ../liveusb/gui.py:156 +#: ../liveusb/gui.py:173 msgid "Error: Cannot set the label or obtain the UUID of your device. Unable to continue." msgstr "Fehler: Kann die Beschriftung nicht setzen oder die UUID Ihres Gerätes erhalten. Kann nicht fortfahren." -#: ../liveusb/gui.py:185 +#: ../liveusb/gui.py:203 #, python-format msgid "Complete! (%s)" msgstr "Komplett! (%s)" -#: ../liveusb/gui.py:188 -#: ../liveusb/gui.py:191 +#: ../liveusb/gui.py:207 msgid "LiveUSB creation failed!" msgstr "LiveUSB-Erzeugung fehlgeschlagen!" -#: ../liveusb/gui.py:331 +#: ../liveusb/gui.py:353 msgid "Persistent Storage" msgstr "Persistenter Speicher" -#: ../liveusb/gui.py:349 +#: ../liveusb/gui.py:376 msgid "" "Your device already contains a LiveOS.\n" "If you continue, this will be overwritten." @@ -58,43 +57,43 @@ msgstr "" "Ihr Gerät enthält ein LiveOS.\n" "Wenn Sie fortsetzen, wird es überschrieben." -#: ../liveusb/gui.py:352 +#: ../liveusb/gui.py:379 msgid "Warning: Creating a new persistent overlay will delete your existing one." msgstr "Warnung: Das Erzeugen eines neuen persistenten Overlay löscht ein vorhandenes." -#: ../liveusb/gui.py:354 +#: ../liveusb/gui.py:381 msgid "Press 'Create Live USB' again if you wish to continue." msgstr "Drücken Sie 'Create Live USB' nochmals, wenn Sie fortfahren wollen." -#: ../liveusb/gui.py:400 +#: ../liveusb/gui.py:428 msgid "Download complete!" msgstr "Herunterladen abgeschlossen!" -#: ../liveusb/gui.py:404 +#: ../liveusb/gui.py:432 msgid "Download failed: " msgstr "Herunterladen fehlgeschlagen:" -#: ../liveusb/gui.py:405 +#: ../liveusb/gui.py:433 msgid "You can try again to resume your download" msgstr "Sie können versuchen das Herunterladen wieder aufzunehmen" -#: ../liveusb/gui.py:409 +#: ../liveusb/gui.py:437 msgid "Select Live ISO" msgstr "Live ISO-Abbild wählen" -#: ../liveusb/gui.py:416 +#: ../liveusb/gui.py:444 msgid "Sorry, I'm having trouble encoding the filename of your livecd. You may have better luck if you move your ISO to the root of your drive (ie: C:\\)" msgstr "Entschuldigung, ich habe Probleme beim Codieren des Dateinamens Ihrer LiveCD. Vielleicht haben Sie mehr Glück, wenn Sie das ISO-Abbild in das Wurzelverzeichnis Ihres Laufwerkes verschieben (z. B.: C:\\)." -#: ../liveusb/gui.py:422 +#: ../liveusb/gui.py:450 msgid "selected" msgstr "ausgewählt" -#: ../liveusb/creator.py:128 +#: ../liveusb/creator.py:135 msgid "Setting up OLPC boot file..." msgstr "Richte OLPC-Boot-Datei ein ..." -#: ../liveusb/creator.py:180 +#: ../liveusb/creator.py:188 #, python-format msgid "" "There was a problem executing the following command: `%s`\n" @@ -103,23 +102,23 @@ msgstr "" "Es ist ein Fehler bei der Ausführung des folgenden Befehls aufgetreten: `%s`\n" "Ein detaillierter Fehler wurde in die Datei 'liveusb-creator.log' geschrieben" -#: ../liveusb/creator.py:187 +#: ../liveusb/creator.py:195 msgid "Verifying SHA1 of LiveCD image..." msgstr "Verifiziere SHA1 des LiveCD-Abbildes ..." -#: ../liveusb/creator.py:209 +#: ../liveusb/creator.py:217 msgid "Error: The SHA1 of your Live CD is invalid. You can run this program with the --noverify argument to bypass this verification check." msgstr "Fehler: Der SHA1 Ihrer Live CD ist ungültig. Sie können dieses Programm mit dem '--noverify'-Argument ausführen, um die Verifikationsprüfung zu umgehen." -#: ../liveusb/creator.py:215 +#: ../liveusb/creator.py:223 msgid "Unknown ISO, skipping checksum verification" msgstr "Unbekannte ISO-Datei, überspringe Checksummen-Überprüfung" -#: ../liveusb/creator.py:227 +#: ../liveusb/creator.py:235 msgid "Not enough free space on device." msgstr "Nicht genügend freier Platz auf dem Gerät." -#: ../liveusb/creator.py:228 +#: ../liveusb/creator.py:236 #, python-format msgid "" "\n" @@ -128,92 +127,100 @@ msgstr "" "\n" "%d MB ISO + %d MB Overlay > %d MB freier Platz" -#: ../liveusb/creator.py:234 +#: ../liveusb/creator.py:242 msgid "Creating" msgstr "Erzeuge" -#: ../liveusb/creator.py:235 +#: ../liveusb/creator.py:243 msgid "persistent overlay" msgstr "Persistenter Speicher" -#: ../liveusb/creator.py:267 +#: ../liveusb/creator.py:275 msgid "Removing existing Live OS" msgstr "Entferne vorhandenes Live-OS" -#: ../liveusb/creator.py:276 +#: ../liveusb/creator.py:284 #, python-format msgid "Unable to remove previous LiveOS: %s" msgstr "Kann vorheriges LiveOS nicht entfernen: %s" -#: ../liveusb/creator.py:307 +#: ../liveusb/creator.py:315 #, python-format msgid "Cannot find device %s" msgstr "Kann Gerät %s nicht finden" -#: ../liveusb/creator.py:356 +#: ../liveusb/creator.py:334 +msgid "Resetting MBR..." +msgstr "MBR zurücksetzen ..." + +#: ../liveusb/creator.py:382 msgid "Unable to find any USB drives" msgstr "Kann keine USB-Geräte finden" -#: ../liveusb/creator.py:379 +#: ../liveusb/creator.py:405 #, python-format msgid "Filesystem for %s unknown!" msgstr "Dateisystem für %s ist unbekannt!" -#: ../liveusb/creator.py:380 +#: ../liveusb/creator.py:406 msgid "device" msgstr "Gerät" -#: ../liveusb/creator.py:392 +#: ../liveusb/creator.py:418 #, python-format msgid "Unable to mount device: %s" msgstr "Kann Gerät nicht einhängen: %s" -#: ../liveusb/creator.py:428 -#: ../liveusb/creator.py:588 +#: ../liveusb/creator.py:450 +#: ../liveusb/creator.py:677 msgid "Verifying filesystem..." msgstr "Überprüfe Dateisystem ..." -#: ../liveusb/creator.py:431 +#: ../liveusb/creator.py:453 #, python-format msgid "Unknown filesystem for %s. Your device may need to be reformatted." msgstr "Unbekanntes Dateisystem für %s. Ihr Gerät muss neu formatiert werden." -#: ../liveusb/creator.py:434 +#: ../liveusb/creator.py:456 #, python-format msgid "Unsupported filesystem: %s" msgstr "Nicht unterstütztes Dateisystem: %s" -#: ../liveusb/creator.py:458 -#: ../liveusb/creator.py:623 +#: ../liveusb/creator.py:480 +msgid "Your MBR appears to be blank" +msgstr "Ihr MBR scheint leer zu sein" + +#: ../liveusb/creator.py:485 +#: ../liveusb/creator.py:712 msgid "Extracting live image to USB device..." msgstr "Extrahiere Live-Abbild auf USB-Gerät ..." -#: ../liveusb/creator.py:464 +#: ../liveusb/creator.py:491 msgid "Unable to find LiveOS on ISO" msgstr "Kann kein LiveOS auf ISO finden" -#: ../liveusb/creator.py:475 -#: ../liveusb/creator.py:630 +#: ../liveusb/creator.py:503 +#: ../liveusb/creator.py:720 msgid "Wrote to device at" msgstr "Schreibe auf Gerät unter" -#: ../liveusb/creator.py:488 +#: ../liveusb/creator.py:516 msgid "Installing bootloader..." msgstr "Installiere Bootloader ..." -#: ../liveusb/creator.py:526 +#: ../liveusb/creator.py:553 msgid "Verifying ISO MD5 checksum" msgstr "Überprüfe ISO-MD5-Checksumme" -#: ../liveusb/creator.py:584 +#: ../liveusb/creator.py:673 msgid "Unable to find any removable devices" msgstr "Kann keine Wechseldatenträger finden" -#: ../liveusb/creator.py:592 +#: ../liveusb/creator.py:681 msgid "Make sure your USB key is plugged in and formatted with the FAT filesystem" msgstr "Stellen Sie sicher, dass Ihr USB-Stick eingesteckt und mit einem FAT-Dateisystem formatiert ist" -#: ../liveusb/creator.py:595 +#: ../liveusb/creator.py:684 #, python-format msgid "" "Unsupported filesystem: %s\n" @@ -222,92 +229,78 @@ msgstr "" "Nicht unterstütztes Dateisystem: %s\n" "Bitte erstellen Sie eine Daten-Sicherung und formatieren Sie Ihren USB-Stick mit einem FAT-Dateisystem." -#: ../liveusb/creator.py:636 +#: ../liveusb/creator.py:726 msgid "Installing bootloader" msgstr "Installiere Bootloader" -#: ../liveusb/creator.py:678 +#: ../liveusb/creator.py:770 msgid "Cannot find" msgstr "Kann nicht finden" -#: ../liveusb/creator.py:679 +#: ../liveusb/creator.py:771 msgid "Make sure to extract the entire liveusb-creator zip file before running this program." msgstr "Stellen Sie sicher, dass Sie das komplette liveusb-creator Zip-Archiv entpackt haben, bevor Sie das Programm ausführen." -#: ../liveusb/linux_dialog.py:98 #: ../liveusb/windows_dialog.py:104 msgid "Fedora LiveUSB Creator" msgstr "Fedora LiveUSB Creator" -#: ../liveusb/linux_dialog.py:99 #: ../liveusb/windows_dialog.py:105 msgid "This button will begin the LiveUSB creation process. This entails optionally downloading a release (if an existing one wasn't selected), extracting the ISO to the USB device, creating the persistent overlay, and installing the bootloader." msgstr "Diese Schaltfläche startet den Live-USB-Erzeugungsprozess. Dies beinhaltet ein optionales Herunterladen einer Version (wenn keine gewählt wurde), das Übertragen des ISO-Abbildes auf das USB-Gerät, das Erzeugen des persistenten Overlay und das Installieren des Bootloader." -#: ../liveusb/linux_dialog.py:100 #: ../liveusb/windows_dialog.py:106 msgid "Create Live USB" msgstr "Erzeuge Live-USB" -#: ../liveusb/linux_dialog.py:101 #: ../liveusb/windows_dialog.py:107 msgid "This is the status console, where all messages get written to." msgstr "Dies ist die Status-Konsole, in welche alle Nachrichten geschrieben werden." -#: ../liveusb/linux_dialog.py:102 #: ../liveusb/windows_dialog.py:108 msgid "This is the progress bar that will indicate how far along in the LiveUSB creation process you are" msgstr "Dies ist die Fortschrittsanzeige, welche anzeigen wird, wie lange der Live-USB-Erzeugungsprozess dauern wird" -#: ../liveusb/linux_dialog.py:103 #: ../liveusb/windows_dialog.py:109 msgid "If you do not select an existing Live CD, the selected release will be downloaded for you." msgstr "Wenn Sie keine vorhandene Live-CD gewählt haben, wird die gewählte Version für Sie heruntergeladen." -#: ../liveusb/linux_dialog.py:104 #: ../liveusb/windows_dialog.py:110 msgid "Download Fedora" msgstr "Fedora herunterladen" -#: ../liveusb/linux_dialog.py:105 #: ../liveusb/windows_dialog.py:111 msgid "or" msgstr "oder" -#: ../liveusb/linux_dialog.py:106 #: ../liveusb/windows_dialog.py:112 msgid "This button allows you to browse for an existing Live CD ISO that you have previously downloaded. If you do not select one, a release will be downloaded for you automatically." msgstr "Diese Schaltfläche erlaubt Ihnen das Suchen nach einer vorhandenen Live-CD ISO-Datei, welche früher heruntergeladen wurde. Wenn Sie keine wählen, wird automatisch eine Version für Sie heruntergeladen." -#: ../liveusb/linux_dialog.py:107 #: ../liveusb/windows_dialog.py:113 msgid "Use existing Live CD" msgstr "Benutze vorhandene Live-CD" -#: ../liveusb/linux_dialog.py:108 #: ../liveusb/windows_dialog.py:114 msgid "Browse" msgstr "Durchsuchen" -#: ../liveusb/linux_dialog.py:110 #: ../liveusb/windows_dialog.py:116 msgid "This is the USB stick that you want to install your Live CD on. This device must be formatted with the FAT filesystem." msgstr "Dies ist der USB-Stick auf welchem Sie Ihre Live-CD installieren wollen. Das Gerät muss mit einem FAT-Dateisystem formatiert sein." -#: ../liveusb/linux_dialog.py:112 +#: ../liveusb/windows_dialog.py:117 +msgid "Target Device" +msgstr "Ziel-Gerät" + #: ../liveusb/windows_dialog.py:118 msgid "By allocating extra space on your USB stick for a persistent overlay, you will be able to store data and make permanent modifications to your live operating system. Without it, you will not be able to save data that will persist after a reboot." msgstr "Durch das Hinzufügen von weiterem Speicherplatz für das persistente Overlay auf Ihrem USB-Stick, wird es Ihnen möglich sein, Daten und Änderungen permanent für Ihr Live-Betriebssystem zu speichern. Ohne wird es Ihnen nicht möglich sein Daten zu speichern, welche nach einem Neustart noch verfügbar sind. " -#: ../liveusb/linux_dialog.py:113 #: ../liveusb/windows_dialog.py:119 msgid "Persistent Storage (0 Mb)" msgstr "Persistenter Speicher (0 MB)" -#: ../liveusb/windows_dialog.py:117 -msgid "Target Device" -msgstr "Ziel-Gerät" - #~ msgid "Creating %d MB persistent overlay..." #~ msgstr "Erzeuge %d MB persitentes Overlay ..." #~ msgid "Creating %sMB persistent overlay"

1 0

3 commits - liveusb-creator liveusb-creator.spec liveusb/gui.py setup.py
by Luke Macken 19 Feb '09

19 Feb '09

liveusb-creator | 2 +- liveusb-creator.spec | 5 ++++- liveusb/gui.py | 10 +++++----- setup.py | 4 ++-- 4 files changed, 12 insertions(+), 9 deletions(-) New commits: commit 20e3b20f17d64111a5f89525ccddf22d2d9c08d7 Author: Luke Macken <lmacken(a)redhat.com> Date: Tue Feb 17 03:47:43 2009 -0500 Revert "Fix some Python2.6 deprecation warnings with regard to the BaseException.message" This reverts commit e872c822b1363bcfe70bb8049d96552627a4e14f, and potentially resolves bug #480673. diff --git a/liveusb/gui.py b/liveusb/gui.py index 9ab94d2..0f3b0af 100755 --- a/liveusb/gui.py +++ b/liveusb/gui.py @@ -203,7 +203,7 @@ class LiveUSBThread(QtCore.QThread): self.status(_("Complete! (%s)" % duration)) except Exception, e: - self.status(str(e)) + self.status(e.message) self.status(_("LiveUSB creation failed!")) self.live.log.exception(e) @@ -272,7 +272,7 @@ class LiveUSBDialog(QtGui.QDialog, LiveUSBInterface): self.driveBox.addItem(device) self.startButton.setEnabled(True) except LiveUSBError, e: - self.textEdit.setPlainText(str(e).encode('utf8')) + self.textEdit.setPlainText(e.message.encode('utf8')) self.startButton.setEnabled(False) def populate_releases(self): @@ -367,7 +367,7 @@ class LiveUSBDialog(QtGui.QDialog, LiveUSBInterface): try: self.live.mount_device() except LiveUSBError, e: - self.status(str(e)) + self.status(e.message) self.enable_widgets(True) return @@ -392,7 +392,7 @@ class LiveUSBDialog(QtGui.QDialog, LiveUSBInterface): try: self.live.delete_liveos() except LiveUSBError, e: - self.status(str(e)) + self.status(e.message) self.live.unmount_device() self.enable_widgets(True) return @@ -440,7 +440,7 @@ class LiveUSBDialog(QtGui.QDialog, LiveUSBInterface): try: self.live.iso = self._to_unicode(isofile) except Exception, e: - self.live.log.error(str(e).encode('utf8')) + self.live.log.error(e.message.encode('utf8')) self.status(_("Sorry, I'm having trouble encoding the filename " "of your livecd. You may have better luck if " "you move your ISO to the root of your drive " commit e1e4af2df5ffd8f0017782dcb0c6f73d7ef40fb0 Merge: 648f69b... c3b4ac4... Author: Luke Macken <lmacken(a)redhat.com> Date: Tue Feb 17 03:46:37 2009 -0500 Merge branch 'master' of ssh://git.fedorahosted.org/git/liveusb-creator commit 648f69bd6d83fd9e607b5826fa60675dc6b53e4d Author: Luke Macken <lmacken(a)redhat.com> Date: Fri Jan 16 20:55:49 2009 -0500 v3.5 diff --git a/liveusb-creator b/liveusb-creator index da296ec..635e0b1 100755 --- a/liveusb-creator +++ b/liveusb-creator @@ -18,7 +18,7 @@ # # Author(s): Luke Macken <lmacken(a)redhat.com> -__version__ = '3.4' +__version__ = '3.5' def parse_args(): from optparse import OptionParser diff --git a/liveusb-creator.spec b/liveusb-creator.spec index 5d9e380..c0277c5 100644 --- a/liveusb-creator.spec +++ b/liveusb-creator.spec @@ -1,7 +1,7 @@ %{!?python_sitelib: %define python_sitelib %(%{__python} -c "from distutils.sysconfig import get_python_lib; print get_python_lib()")} Name: liveusb-creator -Version: 3.4 +Version: 3.5 Release: 1%{?dist} Summary: A liveusb creator @@ -66,6 +66,9 @@ rm -rf %{buildroot} %config(noreplace) %{_sysconfdir}/security/console.apps/%{name} %changelog +* Fri Jan 16 2009 Luke Macken <lmacken(a)redhat.com> 3.5-1 +- Update to v3.5 + * Fri Jan 16 2009 Luke Macken <lmacken(a)redhat.com> 3.4-1 - Update to 3.4. diff --git a/setup.py b/setup.py index 509b20b..31929ce 100644 --- a/setup.py +++ b/setup.py @@ -14,7 +14,7 @@ if sys.platform == 'win32': setup( name = 'liveusb-creator', - version = '3.4', + version = '3.5', packages = ['liveusb', 'liveusb/urlgrabber'], scripts = ['liveusb-creator'], license = 'GNU General Public License (GPL)', @@ -55,7 +55,7 @@ if sys.platform == 'win32': else: setup( name = 'liveusb-creator', - version = '3.4', + version = '3.5', packages = ['liveusb'], scripts = ['liveusb-creator'], license = 'GNU General Public License (GPL)',

1 0

RE: liveusb-creator Digest, Vol 7, Issue 2
by Mike Butler 12 Feb '09

12 Feb '09

Where is it stored in gconf? I'm using Fedora 10, logged in as liveuser. I have an icon on the desktop to Install to hard drive. I've tried what you recommended, but the IPv4 settings do not stay persistent after a reboot. I looked in /etc/gconf for anything that looked like a network related file, but couldn't find anything. Any ideas? Mike > From: liveusb-creator-request(a)lists.fedorahosted.org > Subject: liveusb-creator Digest, Vol 7, Issue 2 > To: liveusb-creator(a)lists.fedorahosted.org > Date: Thu, 12 Feb 2009 12:00:04 +0000 > > Send liveusb-creator mailing list submissions to > liveusb-creator(a)lists.fedorahosted.org > > To subscribe or unsubscribe via the World Wide Web, visit > https://fedorahosted.org/mailman/listinfo/liveusb-creator > or, via email, send a message with subject or body 'help' to > liveusb-creator-request(a)lists.fedorahosted.org > > You can reach the person managing the list at > liveusb-creator-owner(a)lists.fedorahosted.org > > When replying, please edit your Subject line so it is more specific > than "Re: Contents of liveusb-creator digest..." > > > Today's Topics: > > 1. Remember network information upon reboot (Mike Butler) > 2. Re: Remember network information upon reboot (Luke Macken) > > > ---------------------------------------------------------------------- > > Message: 1 > Date: Wed, 11 Feb 2009 18:15:32 +0000 > From: Mike Butler <butlerm1977(a)hotmail.com> > Subject: Remember network information upon reboot > To: <liveusb-creator(a)lists.fedorahosted.org> > Message-ID: <BLU106-W40F9CFC118FBC6FFAF2DBFB2BA0(a)phx.gbl> > Content-Type: text/plain; charset="windows-1252" > > > Newbie here, how to I make network information persistent? I'd like to set the IP, Subnet, Gateway and DNS to stay persistent throughout reboots. > > Thanks, > Mike > > _________________________________________________________________ > See how Windows Mobile brings your life together?at home, work, or on the go. > http://clk.atdmt.com/MRT/go/msnnkwxp1020093182mrt/direct/01/ > -------------- next part -------------- > An HTML attachment was scrubbed... > URL: https://fedorahosted.org/pipermail/liveusb-creator/attachments/20090211/b19… > > ------------------------------ > > Message: 2 > Date: Wed, 11 Feb 2009 19:52:56 -0500 > From: Luke Macken <lmacken(a)redhat.com> > Subject: Re: Remember network information upon reboot > To: liveusb-creator(a)lists.fedorahosted.org > Message-ID: <20090212005256.GA3769@x300> > Content-Type: text/plain; charset=us-ascii > > On Wed, Feb 11, 2009 at 06:15:32PM +0000, Mike Butler wrote: > > > > Newbie here, how to I make network information persistent? I'd like to set the IP, Subnet, Gateway and DNS to stay persistent throughout reboots. > > > Using Fedora 10+, You should be able to right-click on NetworkManager > and use the Connection Editor. I'm guessing that data is probably > stored in gconf, which should persist in the overlay just fine. > > luke > > > ------------------------------ > > _______________________________________________ > liveusb-creator mailing list > liveusb-creator(a)lists.fedorahosted.org > https://fedorahosted.org/mailman/listinfo/liveusb-creator > > > End of liveusb-creator Digest, Vol 7, Issue 2 > ********************************************* _________________________________________________________________ See how Windows connects the people, information, and fun that are part of your life. http://clk.atdmt.com/MRT/go/msnnkwxp1020093175mrt/direct/01/

1 0

Remember network information upon reboot
by Mike Butler 12 Feb '09

12 Feb '09

Newbie here, how to I make network information persistent? I'd like to set the IP, Subnet, Gateway and DNS to stay persistent throughout reboots. Thanks, Mike _________________________________________________________________ See how Windows Mobile brings your life together—at home, work, or on the go. http://clk.atdmt.com/MRT/go/msnnkwxp1020093182mrt/direct/01/

2 1

po/sk.po
by Transifex System User 10 Feb '09

10 Feb '09

po/sk.po | 150 ++++++++++++++++++++++++++++++++------------------------------- 1 file changed, 78 insertions(+), 72 deletions(-) New commits: commit c3b4ac4197605471ae64bf5e138941443608e407 Author: Ondrej Sulek <feonsu(a)gmail.com> Date: Tue Feb 10 09:40:07 2009 +0000 Corrected and updated Slovak translation. Transmitted-via: Transifex (translate.fedoraproject.org) diff --git a/po/sk.po b/po/sk.po index bdf6ef8..348f829 100644 --- a/po/sk.po +++ b/po/sk.po @@ -1,20 +1,20 @@ # Slovak translation for liveusb-creator package. # This file is distributed under the same license as the liveusb-creator package. # -# Ondrej Šulek <feonsu(a)gmail.com>, 2008. +# Ondrej Šulek <feonsu(a)gmail.com>, 2008, 2009. msgid "" msgstr "" "Project-Id-Version: liveusb-creator\n" "Report-Msgid-Bugs-To: \n" -"POT-Creation-Date: 2008-10-19 02:13+0000\n" -"PO-Revision-Date: 2008-10-20 09:04+0200\n" +"POT-Creation-Date: 2008-12-13 01:37+0000\n" +"PO-Revision-Date: 2009-02-10 10:22+0100\n" "Last-Translator: Ondrej Šulek <feonsu(a)gmail.com>\n" "Language-Team: Slovak <fedora-trans-sk(a)redhat.com>\n" "MIME-Version: 1.0\n" "Content-Type: text/plain; charset=UTF-8\n" "Content-Transfer-Encoding: 8bit\n" "Plural-Forms: nplurals=3; plural=(n==1) ? 0 : (n>=2 && n<=4) ? 1 : 2;\n" -"X-Generator: Lokalize 0.2\n" +"X-Generator: Lokalize 0.3\n" #: ../liveusb/__init__.py:42 msgid "You must run this application as root" @@ -35,8 +35,8 @@ msgid "" "Error: Cannot set the label or obtain the UUID of your device. Unable to " "continue." msgstr "" -"Chyba: Nedá sa nastaviť menovka alebo získať UUID vašeho zariadenia. Nemôžem " -"pokračovať." +"Chyba: Nedá sa nastaviť menovka alebo získať UUID vašeho zariadenia. Nie je " +"možné pokračovať." #: ../liveusb/gui.py:185 #, python-format @@ -57,11 +57,11 @@ msgid "" "If you continue, this will be overwritten." msgstr "" "Vaše zariadenie už obsahuje LiveOS.\n" -"Ak budete pokračovať, bude prepísaný." +"Pri pokračovaní, bude prepísaný." #: ../liveusb/gui.py:352 msgid "Warning: Creating a new persistent overlay will delete your existing one." -msgstr "Upozornenie: vytvorením nového trvalého úložiska zmažete už existujúce." +msgstr "Upozornenie: vytvorením nového trvalého úložiska sa zmaže už existujúce." #: ../liveusb/gui.py:354 msgid "Press 'Create Live USB' again if you wish to continue." @@ -77,7 +77,7 @@ msgstr "Sťahovanie zlyhalo: " #: ../liveusb/gui.py:405 msgid "You can try again to resume your download" -msgstr "Skúste znovu spustiť vaše sťahovanie" +msgstr "Skúste znovu spustiť sťahovanie" #: ../liveusb/gui.py:409 msgid "Select Live ISO" @@ -88,18 +88,18 @@ msgid "" "Sorry, I'm having trouble encoding the filename of your livecd. You may " "have better luck if you move your ISO to the root of your drive (ie: C:\\)" msgstr "" -"Nastal problém s kódovaním mena súboru vašeho LiveCD. Možno budete mať " -"viacej šťastia ak ISO presunete do koreňa vášho disku (napr. C:\\)" +"Nastal problém s kódovaním mena súboru LiveCD. Skúste presunúť ISO do koreňa " +"vášho disku (napr. C:\\)" #: ../liveusb/gui.py:422 msgid "selected" msgstr "vybrané" -#: ../liveusb/creator.py:128 +#: ../liveusb/creator.py:134 msgid "Setting up OLPC boot file..." -msgstr "Nastavujem zavádzací súbor OLPC..." +msgstr "Nastavuje sa zavádzací súbor OLPC..." -#: ../liveusb/creator.py:180 +#: ../liveusb/creator.py:186 #, python-format msgid "" "There was a problem executing the following command: `%s`\n" @@ -108,27 +108,28 @@ msgstr "" "Nastal problém so spúšťaním nasledujúceho príkazu: `%s`\n" "Viac detailov o tejto chybe bude zapísaných do 'liveusb-creator.log'" -#: ../liveusb/creator.py:187 +#: ../liveusb/creator.py:193 msgid "Verifying SHA1 of LiveCD image..." -msgstr "Kontrolujem SHA1 LiveCD obrazu..." +msgstr "Kontroluje sa SHA1 LiveCD obrazu..." -#: ../liveusb/creator.py:209 +#: ../liveusb/creator.py:215 msgid "" "Error: The SHA1 of your Live CD is invalid. You can run this program with " "the --noverify argument to bypass this verification check." msgstr "" -"Chyba: SHA1 vašeho Live CD je neplatná. Aby ste preskočili túto kontrolu, " -"môžete spustiť program s parametrom --noverify." +"Chyba: SHA1 kontrolný súčet Live CD je neplatný. Na preskočenie tejto " +"kontroly, " +"spustite program s parametrom --noverify." -#: ../liveusb/creator.py:215 +#: ../liveusb/creator.py:221 msgid "Unknown ISO, skipping checksum verification" -msgstr "Neznáme ISO, preskakujem overenie kontrolného súčtu" +msgstr "Neznáme ISO, preskakuje sa overenie kontrolného súčtu" -#: ../liveusb/creator.py:227 +#: ../liveusb/creator.py:233 msgid "Not enough free space on device." msgstr "Na zariadení nie je dostatok miesta." -#: ../liveusb/creator.py:228 +#: ../liveusb/creator.py:234 #, python-format msgid "" "\n" @@ -137,117 +138,123 @@ msgstr "" "\n" "%dMB ISO + %dMB trvalé úložisko > %dMB voľné miesto" -#: ../liveusb/creator.py:234 +#: ../liveusb/creator.py:240 msgid "Creating" -msgstr "Vytváram" +msgstr "Vytvára sa" -#: ../liveusb/creator.py:235 +#: ../liveusb/creator.py:241 msgid "persistent overlay" msgstr "trvalé úložisko" -#: ../liveusb/creator.py:267 +#: ../liveusb/creator.py:273 msgid "Removing existing Live OS" -msgstr "Odstraňujem existujúci Live OS" +msgstr "Odstraňuje sa existujúci Live OS" -#: ../liveusb/creator.py:276 +#: ../liveusb/creator.py:282 #, python-format msgid "Unable to remove previous LiveOS: %s" msgstr "Nepodarilo sa odstrániť predchádzajúci LiveOS: %s" -#: ../liveusb/creator.py:307 +#: ../liveusb/creator.py:313 #, python-format msgid "Cannot find device %s" -msgstr "Nemôžem nájsť zariadenie %s" +msgstr "Nepodarilo sa nájsť zariadenie %s" -#: ../liveusb/creator.py:356 +#: ../liveusb/creator.py:332 +msgid "Resetting MBR..." +msgstr "Obnovuje sa MBR..." + +#: ../liveusb/creator.py:377 msgid "Unable to find any USB drives" -msgstr "Nemôžem nájsť žiadne USB disky" +msgstr "Nepodarilo sa nájsť žiadne USB disky" -#: ../liveusb/creator.py:379 +#: ../liveusb/creator.py:400 #, python-format msgid "Filesystem for %s unknown!" msgstr "Neznámy súborový systém pre %s!" -#: ../liveusb/creator.py:380 +#: ../liveusb/creator.py:401 msgid "device" msgstr "zariadenie" -#: ../liveusb/creator.py:392 +#: ../liveusb/creator.py:413 #, python-format msgid "Unable to mount device: %s" msgstr "Nepodarilo sa pripojiť zariadenie: %s" -#: ../liveusb/creator.py:428 ../liveusb/creator.py:588 +#: ../liveusb/creator.py:449 ../liveusb/creator.py:614 msgid "Verifying filesystem..." -msgstr "Kontrolujem súborový systém..." +msgstr "Kontroluje sa súborový systém..." -#: ../liveusb/creator.py:431 +#: ../liveusb/creator.py:452 #, python-format msgid "Unknown filesystem for %s. Your device may need to be reformatted." msgstr "" -"Neznámy súborový systém pre %s. Vaše zariadenie pravdepodobne potrebuje " -"preformátovať." +"Neznámy súborový systém pre %s. Zariadenie pravdepodobne potrebuje " +"pre-formátovať." -#: ../liveusb/creator.py:434 +#: ../liveusb/creator.py:455 #, python-format msgid "Unsupported filesystem: %s" msgstr "Nepodporovaný súborový systém: %s" -#: ../liveusb/creator.py:458 ../liveusb/creator.py:623 +#: ../liveusb/creator.py:479 +msgid "Your MBR appears to be blank" +msgstr "MBR sa zdá byť prázdna" + +#: ../liveusb/creator.py:484 ../liveusb/creator.py:649 msgid "Extracting live image to USB device..." -msgstr "Rozbaľujem live obraz na USB zariadenie..." +msgstr "Rozbaľovanie live obrazu na USB zariadenie..." -#: ../liveusb/creator.py:464 +#: ../liveusb/creator.py:490 msgid "Unable to find LiveOS on ISO" msgstr "Nepodarilo sa nájsť LiveOS v ISO" -#: ../liveusb/creator.py:475 ../liveusb/creator.py:630 -#, fuzzy +#: ../liveusb/creator.py:501 ../liveusb/creator.py:656 msgid "Wrote to device at" -msgstr "Zápísané na zariadenie za" +msgstr "Zapísané na zariadenie za" -#: ../liveusb/creator.py:488 +#: ../liveusb/creator.py:514 msgid "Installing bootloader..." -msgstr "Inštalujem zavádzač..." +msgstr "Inštaluje sa zavádzač..." -#: ../liveusb/creator.py:526 +#: ../liveusb/creator.py:552 msgid "Verifying ISO MD5 checksum" -msgstr "Overujem kontrolný súčet ISO MD5" +msgstr "Overuje sa ISO kontrolný súčet MD5" -#: ../liveusb/creator.py:584 +#: ../liveusb/creator.py:610 msgid "Unable to find any removable devices" -msgstr "Nepodarilo sa nájsť žiadne vymeniteľné zariadenie" +msgstr "Nepodarili sa nájsť žiadne vymeniteľné zariadenia" -#: ../liveusb/creator.py:592 +#: ../liveusb/creator.py:618 msgid "" "Make sure your USB key is plugged in and formatted with the FAT filesystem" msgstr "" -"Uistite sa, že váš USB kľúč je pripojený a naformátovaný na súborový systém " -"FAT" +"Skontrolujte, či je USB kľúč pripojený a naformátovaný na súborový systém FAT" -#: ../liveusb/creator.py:595 +#: ../liveusb/creator.py:621 #, python-format msgid "" "Unsupported filesystem: %s\n" "Please backup and format your USB key with the FAT filesystem." msgstr "" "Nepodporovaný súborový systém: %s\n" -"Prosím zálohujte a naformátujte váš USB kľúč na súborový systém FAT." +"Spravte zálohu a naformátujte USB kľúč na súborový systém FAT." -#: ../liveusb/creator.py:636 +#: ../liveusb/creator.py:662 msgid "Installing bootloader" -msgstr "Inštalujem zavádzač" +msgstr "Inštaluje sa zavádzač" -#: ../liveusb/creator.py:678 +#: ../liveusb/creator.py:704 msgid "Cannot find" -msgstr "Nemôžem nájsť" +msgstr "Nepodarilo sa nájsť" -#: ../liveusb/creator.py:679 +#: ../liveusb/creator.py:705 msgid "" "Make sure to extract the entire liveusb-creator zip file before running this " "program." msgstr "" -"Uistite sa, že ste rozbalili celý zip súbor liveusb-creator pred spustením " +"Skontrolujte, či ste rozbalili celý zip súbor liveusb-creator pred spustením " "tohto programu." #: ../liveusb/linux_dialog.py:98 ../liveusb/windows_dialog.py:104 @@ -262,7 +269,7 @@ msgid "" "installing the bootloader." msgstr "" "Toto tlačítko začne proces vytvorenia LiveUSB. Bude to mať za následok " -"prípadné stiahnutie vydania (ak žiadne existujúce nebolo vybrané), " +"prípadné stiahnutie vydania (ak žiadne existujúce nebolo vybrané), " "rozbalenie ISO na USB zariadenie, vytvorenie trvalého úložiska a inštaláciu " "zavádzača." @@ -272,14 +279,14 @@ msgstr "Vytvoriť Live USB" #: ../liveusb/linux_dialog.py:101 ../liveusb/windows_dialog.py:107 msgid "This is the status console, where all messages get written to." -msgstr "Toto je stavová konzola, kde budú vypisované všetky správy." +msgstr "Stavová konzola, kde budú vypisované všetky správy." #: ../liveusb/linux_dialog.py:102 ../liveusb/windows_dialog.py:108 msgid "" "This is the progress bar that will indicate how far along in the LiveUSB " "creation process you are" msgstr "" -"Toto je ukazovateľ priebehu, ktorý indikuje ako ďaleko sa nachádza proces " +"Ukazovateľ priebehu, ktorý indikuje ako ďaleko sa nachádza proces " "vytvárania LiveUSB" #: ../liveusb/linux_dialog.py:103 ../liveusb/windows_dialog.py:109 @@ -320,7 +327,7 @@ msgid "" "This is the USB stick that you want to install your Live CD on. This device " "must be formatted with the FAT filesystem." msgstr "" -"Toto je USB kľúč, na ktorý chcete nainštalovať vaše Live CD. Zariadenie musí " +"Toto je USB kľúč, na ktorý chcete nainštalovať Live CD. Zariadenie musí " "byť naformátované na súborový systém FAT." #: ../liveusb/linux_dialog.py:112 ../liveusb/windows_dialog.py:118 @@ -331,8 +338,8 @@ msgid "" "persist after a reboot." msgstr "" "Pridelením miesta pre trvalé úložisko na váš USB kľúč budete schopný ukladať " -"dáta a vytvárať trvalé zmeny vášho Live operačného systému. Bez neho, " -"nebudete schopný ukladať dáta, ktoré ostanú uložené aj po reštarte." +"dáta a trvalé zmeny vášho Live operačného systému. Bez neho neostanú zmeny " +"po reštarte počítača uložené." #: ../liveusb/linux_dialog.py:113 ../liveusb/windows_dialog.py:119 msgid "Persistent Storage (0 Mb)" @@ -347,4 +354,3 @@ msgstr "Cieľové zariadenie" #~ msgid "Creating %sMB persistent overlay" #~ msgstr "Vytváram %sMB trvalé úložisko" -

1 0

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

liveusb-creator February 2009