< Quoting private mail in public -- I'm sure you'll forgive me >
On Wed, 2004-11-17 at 14:11 +0800, Colin Charles wrote:
> Are all updates that have been generated (~120+ now) been saved
> somewhere, where they are *.ppc.rpm ?
> We can always host them on fedora.linux.duke.edu if required, but
> someone needs to poke around the build system and grab it (David did
> this for FC2!)
They've actually stopped building fc2 updates for ppc now,
My system is Lite5200 with DENX Embedded Linux running on it.I want to connect USB mass storage devices to my computer's USB port.But I found there is no driver in kernel.(when I use 'make xconfig' the USB mass storage devices driver is in grey).How can I download/install the driver and active my USB disk?
My system is Lite5200 with DENX Embedded Linux running on it.When I tried to enable my USB port to use my u-disk,
the problem occured.
I have enabled USB support with 'make xconfig'. The reports are as follows:
U-Boot 1.1.2 (Nov 12 2004 - 11:46:06)
CPU: MPC5200 v1.2 at 462 MHz
Bus 132 MHz, IPB 132 MHz, PCI 33 MHz
Board: Motorola MPC5200 (IceCube)
I2C: 85 kHz, ready
DRAM: 64 MB
FLASH: 16 MB
PCI: Bus Dev VenId DevId Class Int
00 1a 1057 5803 0680 00
Net: FEC ETHERNET
IDE: Bus 0: OK
Device 0: Model: Flash Card Firm: 2N3-0925 Ser#: CF00000000
Type: Removable Hard Disk
Capacity: 123.0 MB = 0.1 GB (251904 x 512)
Device 1: not available
Autostarting.Press any key to abort..
Hit any key to stop autoboot: 0
Using FEC ETHERNET device
TFTP from server 184.108.40.206; our IP address is 220.127.116.11
Load address: 0x100000
Bytes transferred = 857559 (d15d7 hex)
## Booting image at 00100000 ...
Image Name: Linux-2.4.25
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 857495 Bytes = 837.4 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb
Linux version 2.4.25 (root(a)18.104.22.168.netdial.caribe.net) (gcc version 3.2.24
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=22.214.171.124:/home/zl/ELDK/ppc_8f
Calibrating delay loop... 307.20 BogoMIPS
Memory: 62212k available (1500k kernel code, 464k data, 76k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 00:1a.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Journalled Block Device driver loaded
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
pty: 256 Unix98 ptys configured
ttyS0 on PSC1
ttyS1 on PSC2
ttyS2 on PSC3
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Port Config is: 0x11050004
ipb=132MHz, set clock period to 7
GPIO config: 11050004
ATA invalid: 01000000
ATA hostcnf: 03000000
ATA pio1 : 100a0a00
ATA pio2 : 02040600
XLB Arb cnf: 0000a366
mpc5xxx_ide: Setting up IDE interface ide0...
ATA DMA task: 5
Probing IDE interface ide0...
hda: Flash Card, CFA DISK drive
ide0 at 0xf0003a60-0xf0003a67,0xf0003a5c on irq 45
hda: attached ide-disk driver.
hda: 251904 sectors (129 MB) w/0KiB Cache, CHS=984/16/16
Icecube Bank 0: Found 1 x8 devices at 0x0 in 8-bit mode
Icecube Bank 0: Found 1 x8 devices at 0x800000 in 8-bit mode
Amd/Fujitsu Extended Query Table at 0x0040
Icecube Bank 0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 2
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Icecube flash bank 0: Using static image partition definition
Creating 5 MTD partitions on "Icecube Bank 0":
0x00000000-0x00800000 : "Spare"
0x00800000-0x00900000 : "kernel"
0x00900000-0x00c00000 : "initrd"
0x00c00000-0x00f00000 : "jffs"
0x00f00000-0x01000000 : "Firmware"
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0xf0001000, IRQ 44
host/usb-ohci.c: usb-0, Built-In ohci
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 1 port detected
NET4: Linux TCP/IP 1.0 for NET4.0
eth0: Phy @ 0x0, type LXT971 (0x001378e2)
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX.
eth0: Waiting for the link to be up...
eth0: status: link up, 100 Mbps Full Duplex, auto-negotiation complete.
device=eth0, addr=126.96.36.199, mask=255.0.0.0, gw=188.8.131.52,
host=icecube, domain=, nis-domain=(none),
bootserver=184.108.40.206, rootserver=220.127.116.11, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 18.104.22.168
Looking up port of RPC 100005/1 on 22.214.171.124
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 76k init
INIT: version 2.84 booting
Welcome to DENX Embedded Linux Environment
Press 'I' to enter interactive startup.
Building the cache [ OK ]
Mounting proc filesystem: [ OK ]
Configuring kernel parameters: [ OK ]
RTC_RD_TIME: Invalid argument
ioctl() to /dev/rtc to read the time failed.
Setting clock : Wed Dec 31 19:00:09 EST 1969 [ OK ]
Setting hostname icecube: [ OK ]
Mounting USB filesystem: mount: mount point /proc/bus/usb does not exist
Activating swap partitions: [ OK ]
[ OK ]
Mounting local filesystems: [ OK ]
Enabling swap space: [ OK ]
modprobe: Can't open dependencies file /lib/modules/2.4.25/modules.dep (No such)
INIT: Entering runlevel: 3
Entering non-interactive startup
Setting network parameters: [ OK ]
Bringing up loopback interface: [ OK ]
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Initializing random number generator: [ OK ]
Starting portmapper: [ OK ]
Mounting NFS filesystems: [ OK ]
Mounting other filesystems: [ OK ]
Starting xinetd: [ OK ]
icecube login: root
Last login: Wed Dec 31 19:02:11 on console
It seems that the USB port has been detected.But the filesystem mounted unsuccessfully!(Mounting USB filesystem:
mount: mount point /proc/bus/usb does not exist)
Please give a hand! Thanks in advance!!!!!
On Fri, 2004-11-26 at 07:00 +0000, Michael A. Peters wrote:
Please follow-up to fedora-ppc(a)lists.infradead.org
> Not using dhcp - using a static IP on my lan.
> Network init script says it was starting, but eth0 was never brought
Later, when the computer starts, if ifup eth0 doesn't work, can you
bring the interface up manually using ifconfig ?
> It's possible that the network (ifcfg-eth0) setting set up by YDL were
> not sufficient for FC - I tried manually adjusting ifcfg-eth0 to look
> similar to the ifcfg-eth0 on an x86 FC3 box, but that didn't work -
> even when I tried modprobing various modules I thought might be
Why did you install YDL to bootstrap fedora? Fedora itself installs fine
> responsible. I also tried running the network config tool - it didn't
> recognize eth0. I suspect it may be fixed by a newer kernel, but there
> were deps not installed when I tried to install it - I really need to
> get one of those USB keychain thingies, but I don't have one.
What kernel is this?
> I tried modprobing mace, sungem, a few others that looked reasonable (I
> believe mace is the correct one) - but the installed kernel is kind of
sungem is the correct one. What iMac exactly do you have? We would
appreciate lspci output
> old (from C3T2). I want to try with a newer kernel before I file any
> bug reports. I also want to pick up a USB key before I file a bug
> report, to make it easier to try different kernels.
> While I highly doubt this has anything to do with it, this is a first
> gen iMac but it has a Newer 433 G4 cpu daughtercard installed (opposed
> to the 233 G3 it came with) - It's the second rev of the mobo (the one
> used for Rev B/C/D iMacs)
Hmm, post lscpi in your next post (only to fedora-ppc list). What
does /proc/cpuinfo report ? (this is just for my curiosity)
Colin Charles, byte(a)aeon.com.my
"First they ignore you, then they laugh at you, then they fight you,
then you win." -- Mohandas Gandhi
i sucked the ppc-devel-tree to my hd, set up a NFS server for the downloaded
files and burned boot.iso from the dir "mac". The boot cd booted but it
found no network device.
all i know i took from the HOWTO at
I couldn't by all efforts find more about this topic in the net...
If i burn the FC3 PPC development tree on an DVD, boot with a CD and select
"CD-ROM" as Installation method, anaconda tells me that it didn't find a FC
CD that fits to my boot CD. That's allready a bit more than i got with my
first try (DVD without ".disc-info", without "SRPMS" and named other than
"FC-3 ppc"). There it said that it didn'T find a FC CD. my second DVD should
be OK, the only dir that didn't fit onto the dvd was "debug" but i read in
the howto, that i don't need
it. so what's wrong?
I also tried to get help at another maillist:
> On Wed, 2004-11-03 at 14:59 +0000, David Woodhouse wrote:
> I've seen anaconda happily load the sungem driver, then fail to notice
> that there's now an eth0 and demand that you specify a network driver to
> load. Helpfully it notices that sungem is already loaded though, so it
> removes that from the list of options :)
That's what happens to me if i try to install on the PowerMacG3 (350MHz),
but with the bmac driver. alt Alt+F4 it says:
<7> divert: allocating divert_blk for eth0
<6> eth0: BMAC+ at 00:05:02:61:a3:51
so i guess anaconda could load the driver. but it doesn't go further then.
It just keeps me asking to select a driver...
Does anybody have experience with this topic and could give me a hint? Or
can anybody tell me what to do or where it's documented how i can install
FC-3 on Macs? I have a PowerMac G3 (350MHz) and it's really important that i
install fedora there...
Thanks in advance
NEU +++ DSL Komplett von GMX +++ http://www.gmx.net/de/go/dsl
GMX DSL-Netzanschluss + Tarif zum superg�nstigen Komplett-Preis!
I'm looking somewhat puzzled at a G5, sitting at the firmware prompt,
that refuses to run yaboot or ofwboot.elf (both elf-32 executables, they
hang after printing Loading ELF) but happily loads/runs ofwboot.xcf and
tbxi (both xcoff executables).
I'm guessing that there is something in the ELF that it doesn't like :-/
I need the proper XF86Config info for a first gen iMac.
I used the tool Dan Burcaw wrote, but it did not create correct config
ModelName "Monitor Model"
The HorizSync and VertRefresh are clearly not correct - well, HorizSync
might be but startx complains at VertRefresh.
I'm tempted to just invert the 75-60 but I'd rather get a confirmed
This is a first gen iMac running FC2 yum updated from YDL 3 - but the
YDL install was an extremely lite install (no X) for the purpose of
making such update/install easier. So I don't have an existing XF86
config file for it.
Thanks in advance,
Cheap Linux CD's
Installed a minimal YDL 3.0
Removed a bunch of packes.
Tried yum updating to ppc FC3T2 on
Didn't want to do do it - looked like there was stuff there that wanted
different glibc than what it the repo had.
Tried updating to FC2
What's the best way to do this?
Cheap Linux CD's