Hello All,
I was able succesfully install Fedora Sparc 9 on a Sunblade 2500 with XVR-100 card, and everything worked great. I could never get FC-14 to work, but I have recently been trying to insall FC-14 on the same hardware again, and have not been successful. The installation works fine, but when I boot, it always hangs at the "Attached SCSI disk"? I'm able to then boot off the rescue CD, and mount everthing in the chroot environment, and everything looks good?
Here is the output from the boot.
Thanks for any help you can provide.
Restarting system.
Sun Blade 2500, Keyboard Present
Copyright 2005 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.17.1, 4096 MB memory installed, Serial #56412382.
Ethernet address 0:3:ba:5c:c8:de, Host ID: 835cc8de.
Rebooting with command: boot
Boot device: disk File and args:
SILO Version 1.4.14
\
Welcome to Fedora!
Hit <TAB> for boot options
boot:
Allocated 64 Megs of memory at 0x40000000 for kernel
Loaded kernel version 2.6.32
Loading initial ramdisk (12425851 bytes at 0x33F000000 phys, 0x40C00000 virt)...
-
PROMLIB: Sun IEEE Boot Prom 'OBP 4.17.1 2005/04/11 14:24'
PROMLIB: Root node compatible:
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.21-166.fc12.sparc64 (mockbuild(a)korolev.ausil.us) (gcc versi
on 4.4.4 20100726 (Red Hat 4.4.4-14) (GCC) ) #1 SMP Fri Sep 10 13:32:10 UTC 2010
bootconsole [earlyprom0] enabled
ARCH: SUN4U
Ethernet address: 00:03:ba:5c:c8:de
Kernel: Using 3 locked TLB entries for main kernel image.
Remapping the kernel... done.
OF stdout device is: /pci@1e,600000/isa@7/serial@0,3f8
PROM: Built device tree with 99412 bytes of memory.
[0000010000000000-fffff80000400000] page_structs=131072 node=0 entry=0/0
[0000010000000000-fffff80000800000] page_structs=131072 node=0 entry=1/0
[0000010002000000-fffff80000c00000] page_structs=131072 node=0 entry=8/0
[0000010002000000-fffff80001000000] page_structs=131072 node=0 entry=9/0
[0000010004000000-fffff80001400000] page_structs=131072 node=0 entry=16/0
[0000010004000000-fffff80001800000] page_structs=131072 node=0 entry=17/0
[0000010006000000-fffff80001c00000] page_structs=131072 node=0 entry=24/0
[0000010006000000-fffff80002000000] page_structs=131072 node=0 entry=25/0
Zone PFN ranges:
Normal 0x00000000 -> 0x0019ff52
Movable zone start PFN for each node
early_node_map[8] active PFN ranges
0: 0x00000000 -> 0x00020000
0: 0x00080000 -> 0x000a0000
0: 0x00100000 -> 0x00120000
0: 0x00180000 -> 0x0019f7ff
0: 0x0019f800 -> 0x0019fed0
0: 0x0019fed8 -> 0x0019ff2d
0: 0x0019ff35 -> 0x0019ff40
0: 0x0019ff50 -> 0x0019ff52
Could not find start_pfn for node 1
Booting Linux...
PERCPU: Embedded 7 pages/cpu @fffff80002400000 s27200 r8192 d21952 u4194304
pcpu-alloc: s27200 r8192 d21952 u4194304 alloc=1*4194304
pcpu-alloc: [0] 0 [1] 1
Built 2 zonelists in Node order, mobility grouping on. Total pages: 510770
Policy zone: Normal
Kernel command line: root=/dev/mapper/rootvg-lv00 ro LANG=en_US.UTF-8 SYSFONT=la
tarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rootdelay=60
PID hash table entries: 4096 (order: 2, 32768 bytes)
Memory: 4138696k available (4536k kernel code, 2176k data, 400k init) [fffff8000
0000000,000000033fea4000]
SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=16
Hierarchical RCU implementation.
NR_IRQS:255
clocksource: mult[535555] shift[16]
clockevent: mult[3126e97] shift[32]
Console: colour dummy device 80x25
console [tty0] enabled, bootconsole disabled
PROMLIB: Sun IEEE Boot Prom 'OBP 4.17.1 2005/04/11 14:24'
PROMLIB: Root node compatible:
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.32.21-166.fc12.sparc64 (mockbuild(a)korolev.ausil.us) (gcc versi
on 4.4.4 20100726 (Red Hat 4.4.4-14) (GCC) ) #1 SMP Fri Sep 10 13:32:10 UTC 2010
bootconsole [earlyprom0] enabled
ARCH: SUN4U
Ethernet address: 00:03:ba:5c:c8:de
Kernel: Using 3 locked TLB entries for main kernel image.
Remapping the kernel... done.
OF stdout device is: /pci@1e,600000/isa@7/serial@0,3f8
PROM: Built device tree with 99412 bytes of memory.
[0000010000000000-fffff80000400000] page_structs=131072 node=0 entry=0/0
[0000010000000000-fffff80000800000] page_structs=131072 node=0 entry=1/0
[0000010002000000-fffff80000c00000] page_structs=131072 node=0 entry=8/0
[0000010002000000-fffff80001000000] page_structs=131072 node=0 entry=9/0
[0000010004000000-fffff80001400000] page_structs=131072 node=0 entry=16/0
[0000010004000000-fffff80001800000] page_structs=131072 node=0 entry=17/0
[0000010006000000-fffff80001c00000] page_structs=131072 node=0 entry=24/0
[0000010006000000-fffff80002000000] page_structs=131072 node=0 entry=25/0
Zone PFN ranges:
Normal 0x00000000 -> 0x0019ff52
Movable zone start PFN for each node
early_node_map[8] active PFN ranges
0: 0x00000000 -> 0x00020000
0: 0x00080000 -> 0x000a0000
0: 0x00100000 -> 0x00120000
0: 0x00180000 -> 0x0019f7ff
0: 0x0019f800 -> 0x0019fed0
0: 0x0019fed8 -> 0x0019ff2d
0: 0x0019ff35 -> 0x0019ff40
0: 0x0019ff50 -> 0x0019ff52
Could not find start_pfn for node 1
Booting Linux...
PERCPU: Embedded 7 pages/cpu @fffff80002400000 s27200 r8192 d21952 u4194304
pcpu-alloc: s27200 r8192 d21952 u4194304 alloc=1*4194304
pcpu-alloc: [0] 0 [1] 1
Built 2 zonelists in Node order, mobility grouping on. Total pages: 510770
Policy zone: Normal
Kernel command line: root=/dev/mapper/rootvg-lv00 ro LANG=en_US.UTF-8 SYSFONT=la
tarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rootdelay=60
PID hash table entries: 4096 (order: 2, 32768 bytes)
Memory: 4138696k available (4536k kernel code, 2176k data, 400k init) [fffff8000
0000000,000000033fea4000]
SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=16
Hierarchical RCU implementation.
NR_IRQS:255
clocksource: mult[535555] shift[16]
clockevent: mult[3126e97] shift[32]
Console: colour dummy device 80x25
console [tty0] enabled, bootconsole disabled
allocated 20971520 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Calibrating delay using timer specific routine.. 24.01 BogoMIPS (lpj=120060)
Security Framework initialized
SELinux: Initializing.
Dentry cache hash table entries: 524288 (order: 9, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 8, 2097152 bytes)
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
ftrace: allocating 17130 entries in 34 pages
CPU 1: synchronized TICK with master CPU (last diff 0 cycles, maxerr 5 cycles)
Brought up 2 CPUs
devtmpfs: initialized
regulator: core version 0.5
NET: Registered protocol family 16
Testing NMI watchdog ... OK.
Performance events: Supported PMU type is 'ultra3i'
/pci@1c,600000: TOMATILLO PCI Bus Module ver[4:0]
/pci@1c,600000: PCI IO[7ce01000000] MEM[7cf00000000]
PCI: Scanning PBM /pci@1c,600000
pci 0000:00:03.0: PME# supported from D3hot
pci 0000:00:03.0: PME# disabled
/pci@1d,700000: TOMATILLO PCI Bus Module ver[4:0]
/pci@1d,700000: PCI IO[7c601000000] MEM[7c700000000]
PCI: Scanning PBM /pci@1d,700000
/pci@1e,600000: TOMATILLO PCI Bus Module ver[4:0]
/pci@1e,600000: PCI IO[7fe01000000] MEM[7ff00000000]
PCI: Scanning PBM /pci@1e,600000
pci 0002:00:06.0: quirk: region 0800-083f claimed by ali7101 ACPI
pci 0002:00:06.0: quirk: region 0600-061f claimed by ali7101 SMB
pci 0002:00:08.0: PME# supported from D2 D3hot D3cold
pci 0002:00:08.0: PME# disabled
pci 0002:00:0a.0: PME# supported from D3cold
pci 0002:00:0a.0: PME# disabled
pci 0002:00:0b.0: PME# supported from D3cold
pci 0002:00:0b.0: PME# disabled
pci 0002:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0002:01:08.0: PME# disabled
pci 0002:01:08.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0002:01:08.1: PME# disabled
pci 0002:01:08.2: PME# supported from D0 D1 D2 D3hot
pci 0002:01:08.2: PME# disabled
pci 0002:01:0b.0: PME# supported from D0 D1 D2 D3hot
pci 0002:01:0b.0: PME# disabled
/pci@1f,700000: TOMATILLO PCI Bus Module ver[4:0]
/pci@1f,700000: PCI IO[7f601000000] MEM[7f700000000]
PCI: Scanning PBM /pci@1f,700000
bio: create slab <bio-0> at 0
vgaarb: device added: PCI:0002:00:02.0,decodes=io+mem,owns=mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
/pci@1e,600000/isa@7/rtc@0,70: RTC regs at 0x7fe01000070
Switching to clocksource stick
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 7, 1048576 bytes)
TCP established hash table entries: 524288 (order: 10, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 7, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0002:00:07.0: Activating ISA DMA hang workarounds
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 12134k freed
power: Control reg at 7fe01000800
chmc: UltraSPARC-IIIi memory controller at /memory-controller@0,0
chmc: UltraSPARC-IIIi memory controller at /memory-controller@1,0
audit: initializing netlink socket (disabled)
type=2000 audit(1.000:1): initialized
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
msgmni has been set to 8107
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci-stub: invalid id string ""
f00a6930: ttyS0 at MMIO 0x7fe010003f8 (irq = 23) is a 16550A
Console: ttyS0 (SU)
console [ttyS0] enabled
f00a84ac: ttyS1 at MMIO 0x7fe010002e8 (irq = 23) is a 16550A
brd: module loaded
loop: module loaded
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0002:01:08.2: EHCI Host Controller
ehci_hcd 0002:01:08.2: new USB bus registered, assigned bus number 1
ehci_hcd 0002:01:08.2: Enabling legacy PCI PM
ehci_hcd 0002:01:08.2: irq 35, io mem 0x7ff10004000
ehci_hcd 0002:01:08.2: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32.21-166.fc12.sparc64 ehci_hcd
usb usb1: SerialNumber: 0002:01:08.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0002:00:0a.0: OHCI Host Controller
ohci_hcd 0002:00:0a.0: new USB bus registered, assigned bus number 2
ohci_hcd 0002:00:0a.0: irq 27, io mem 0x7ff01000000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32.21-166.fc12.sparc64 ohci_hcd
usb usb2: SerialNumber: 0002:00:0a.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd 0002:00:0b.0: OHCI Host Controller
ohci_hcd 0002:00:0b.0: new USB bus registered, assigned bus number 3
ohci_hcd 0002:00:0b.0: irq 28, io mem 0x7ff02000000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.32.21-166.fc12.sparc64 ohci_hcd
usb usb3: SerialNumber: 0002:00:0b.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd 0002:01:08.0: OHCI Host Controller
ohci_hcd 0002:01:08.0: new USB bus registered, assigned bus number 4
ohci_hcd 0002:01:08.0: irq 33, io mem 0x7ff10000000
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb 3-1: new low speed USB device using ohci_hcd and address 2
usb usb4: Manufacturer: Linux 2.6.32.21-166.fc12.sparc64 ohci_hcd
usb usb4: SerialNumber: 0002:01:08.0
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ohci_hcd 0002:01:08.1: OHCI Host Controller
ohci_hcd 0002:01:08.1: new USB bus registered, assigned bus number 5
ohci_hcd 0002:01:08.1: irq 34, io mem 0x7ff10002000
usb 3-1: New USB device found, idVendor=045e, idProduct=0040
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: OHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.32.21-166.fc12.sparc64 ohci_hcd
usb usb5: SerialNumber: 0002:01:08.1
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
mice: PS/2 mouse device common for all mice
rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
rtc0: no alarms, 114 bytes nvram
device-mapper: uevent: version 1.0.3
usb 3-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel(a)redhat.com
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
registered taskstats version 1
rtc_cmos rtc_cmos: setting system clock to 2011-01-10 19:04:24 UTC (1294686264)
usb 3-1: Product: Microsoft 3-Button Mouse with IntelliEye(TM)
usb 3-1: Manufacturer: Microsoft
usb 3-1: configuration #1 chosen from 1 choice
Initalizing network drop monitor service
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/root/f
0078524/pci0002:00/0002:00:0b.0/usb3/3-1/3-1:1.0/input/input0
generic-usb 0003:045E:0040.0001: input,hidraw0: USB HID v1.10 Mouse [Microsoft M
icrosoft 3-Button Mouse with IntelliEye(TM)] on usb-0002:00:0b.0-1/input0
dracut: dracut-005-2.fc12
udev: starting version 145
usb 3-2: new low speed USB device using ohci_hcd and address 3
[drm] Initialized drm 1.1.0 20060810
[drm] radeon defaulting to kernel modesetting.
[drm] radeon kernel modesetting enabled.
[drm] radeon: Initializing kernel modesetting.
[drm] register mmio base: 0x00110000
[drm] register mmio size: 65536
usb 3-2: New USB device found, idVendor=03f0, idProduct=0024
usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 3-2: Product: HP Basic USB Keyboard
usb 3-2: Manufacturer: CHICONY
usb 3-2: configuration #1 chosen from 1 choice
input: CHICONY HP Basic USB Keyboard as /devices/root/f0078524/pci0002:00/0002:0
0:0b.0/usb3/3-2/3-2:1.0/input/input1
generic-usb 0003:03F0:0024.0002: input,hidraw1: USB HID v1.10 Keyboard [CHICONY
HP Basic USB Keyboard] on usb-0002:00:0b.0-2/input0
radeon 0002:00:02.0: BAR 6: can't allocate resource (bogus alignment) [0x7ff0012
0000-0x7ff0013ffff] flags 0x6200
radeon 0002:00:02.0: BAR 6: can't allocate resource (bogus alignment) [0x7ff0012
0000-0x7ff0013ffff] flags 0x6200
[drm:radeon_get_bios] *ERROR* Unable to locate a BIOS ROM
[drm] GPU reset succeed (RBBM_STATUS=0x00000140)
[drm] Using generic clock info
[drm] radeon: VRAM 64M
[drm] radeon: VRAM from 0x00000000 to 0x03FFFFFF
[drm] radeon: GTT 512M
[drm] radeon: GTT from 0x20000000 to 0x3FFFFFFF
[drm] radeon: irq initialized.
[drm] Detected VRAM RAM=64M, BAR=128M
[drm] RAM width 64bits DDR
[TTM] Zone kernel: Available graphics memory: 2075616 kiB.
[drm] radeon: 64M of VRAM memory ready
[drm] radeon: 512M of GTT memory ready.
[drm] GART: num cpu pages 65536, num gpu pages 131072
[drm] radeon: cp idle (0x00008080)
[drm] Loading R100 Microcode
platform radeon_cp.0: firmware: requesting radeon/R100_cp.bin
[drm] radeon: ring at 0x0000000020000000
[drm] ring test succeeded in 0 usecs
[drm] radeon: ib pool ready.
[drm] ib test succeeded in 0 usecs
Unable to handle kernel NULL pointer dereference
tsk->{mm,active_mm}->context = 0000000000000038
tsk->{mm,active_mm}->pgd = fffff80338664000
\|/ ____ \|/
"@'/ .. \`@"
/_| \__/ |_\
\__U_/
modprobe(90): Oops [#1]
TSTATE: 0000009911001605 TPC: 00000000100a9dac TNPC: 00000000100a9db0 Y: 0000000
0 Not tainted
TPC: <combios_get_table_offset+0x1c0/0x55c [radeon]>
g0: 000000001002c808 g1: 0000000000000000 g2: 0000000000000000 g3: 0000000000000
000
g4: fffff8033861de80 g5: fffff80001d0a000 g6: fffff80338758000 g7: 0000000000a28
180
o0: fffff8033840b000 o1: 0000000000000000 o2: 0000000000000000 o3: fffff8033f0b6
380
o4: fffff803383672a8 o5: 00000000100b3bd8 sp: fffff8033875a851 ret_pc: 000000000
05210b8
RPC: <kmem_cache_alloc_notrace+0xc0/0xd0>
l0: fffff803384a3000 l1: 0000000000000040 l2: 000000001002c734 l3: 0000000000a2b
a20
l4: 0000000000000040 l5: 000000001002c87c l6: 000000005133a330 l7: 0000000000000
000
i0: fffff8033840b000 i1: 0000000000000040 i2: fffff803383672a8 i3: 0000000010036
910
i4: fffff8033840b4d8 i5: fffff8033840b4b8 i6: fffff8033875a911 i7: 00000000100ae
ad8
I7: <radeon_combios_check_hardcoded_edid+0x10/0x22c [radeon]>
Disabling lock debugging due to kernel taint
Caller[00000000100aead8]: radeon_combios_check_hardcoded_edid+0x10/0x22c [radeon
]
Caller[00000000100bf434]: radeon_modeset_init+0x190/0x7b8 [radeon]
Caller[00000000100a4214]: radeon_driver_load_kms+0x134/0x1a0 [radeon]
Caller[00000000100282c4]: drm_get_dev+0x284/0x390 [drm]
Caller[0000000010100b48]: radeon_pci_probe+0x18/0x2dc [radeon]
Caller[0000000000678fd8]: local_pci_probe+0x18/0x2c
Caller[000000000067931c]: pci_device_probe+0xcc/0x104
Caller[00000000006cee5c]: driver_probe_device+0x124/0x294
Caller[00000000006cf028]: __driver_attach+0x5c/0x88
Caller[00000000006ce3dc]: bus_for_each_dev+0x44/0x8c
Caller[00000000006ceb50]: driver_attach+0x1c/0x30
Caller[00000000006cdbe8]: bus_add_driver+0x140/0x2e8
Caller[00000000006cf36c]: driver_register+0xc0/0x170
Caller[0000000000679550]: __pci_register_driver+0x38/0xcc
Caller[0000000010023968]: drm_init+0x58/0xf8 [drm]
Caller[0000000010136094]: radeon_init+0x94/0xa8 [radeon]
Caller[0000000000426ae0]: do_one_initcall+0x4c/0x16c
Caller[000000000049f948]: SyS_init_module+0xc8/0x20c
Caller[00000000004422d0]: sys32_init_module+0x14/0x24
Caller[0000000000406214]: linux_sparc_syscall32+0x34/0x40
Caller[0000000000012ca0]: 0x12ca0
Instruction DUMP: c2142092 c45c2088 82008001 <d008604d> 106800df c208604c c2
142092 c45c2088 82008001
udevd-work[74]: '/sbin/modprobe -b pci:v00001002d00005159sv00001dracut: Starting
plymouth daemon
002sd00000908bc03sc00i00' unexpected exit with status 0x0009
sym0: <1010-66> rev 0x1 at pci 0001:00:04.0 irq 12
sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
sym1: <1010-66> rev 0x1 at pci 0001:00:04.1 irq 13
firewire_ohci: Added fw-ohci device 0002:01:0b.0, OHCI version 1.10
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.3
firewire_core: created device fw0: GUID 00051600004037b1, S400
scsi 0:0:0:0: Direct-Access HITACHI DK32EJ36NSUN36G PQ0F PQ: 0 ANSI: 3
scsi target0:0:0: tagged command queuing enabled, command queue depth 16.
scsi target0:0:0: Beginning Domain Validation
scsi target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 30)
scsi target0:0:0: Ending Domain Validation
scsi 0:0:1:0: Direct-Access SEAGATE ST336607LSUN36G 0507 PQ: 0 ANSI: 3
scsi target0:0:1: tagged command queuing enabled, command queue depth 16.
scsi target0:0:1: Beginning Domain Validation
scsi target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
scsi target0:0:1: Ending Domain Validation
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:1:0: [sdb] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB)
sd 0:0:0:0: [sda] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB)
sd 0:0:1:0: Attached scsi generic sg1 type 0
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and F
UA
sda: sda1 sda2 sda3 sda4
sd 0:0:1:0: [sdb] Write Protect is off
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and F
UA
sdb: sdb3
sd 0:0:1:0: [sdb] Attached SCSI disk
T. Rowe Price (including T. Rowe Price Group, Inc. and its affiliates) and its associates do not provide legal or tax advice. Any tax-related discussion contained in this e-mail, including any attachments, is not intended or written to be used, and cannot be used, for the purpose of (i) avoiding any tax penalties or (ii) promoting, marketing, or recommending to any other party any transaction or matter addressed herein. Please consult your independent legal counsel and/or professional tax advisor regarding any legal or tax issues raised in this e-mail.
The contents of this e-mail and any attachments are intended solely for the use of the named addressee(s) and may contain confidential and/or privileged information. Any unauthorized use, copying, disclosure, or distribution of the contents of this e-mail is strictly prohibited by the sender and may be unlawful. If you are not the intended recipient, please notify the sender immediately and delete this e-mail.
