Well, it's been an interesting time.
I successfully got F12-Beta installed with the default partitioning (using VNC), but the beast refuses to boot all the way up. I did some basic troubleshooting, and performed a full yum update using the rescue image and chrooted to the root, which works great.
The last messages in the default non-quiet non-rhgb mode says: ++++++++++ dracut: dracut-004-4.fc12 udev: starting version 145 dracut: Starting plymouth daemon
No root device found
No root device found
Boot has failed, sleeping forever. ++++++++++++++
Ok, found some references to these strings, and changed my silo.conf to append rdinitdebug rdshell to the command line.
This shows other things at the end, but the root issue is that qlogicpti (boot and root are in the first disk of a D1000 shelf attached to a pair of Qlogic SBUS ISP1000's) isn't getting loaded, even though it is included in the initrd.
I can manually modprobe qlogicpti and get the disks recognized just fine; adding rdloaddriver=qlogicpti (I also added rdloaddriver=sun_esp to get that) to the boot command line does not, failing to find the isp1000.bin firmware file.
So I need to do the following to get it to boot once I get the dracut debug shell: dracut:/# modprobe qlogicpti qlogicpti0: IRQ 19 SCSI ID 7 qpti f00fccd4: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.28 99/11/08) qlogicpti0: [Ultra Wide, using differential interface] scsi3 : PTI Qlogic,ISP SBUS SCSI irq 19 regs at 000001c700010000 qlogicpti1: IRQ 45 SCSI ID 7 qpti f02b6520: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.25 96/10/15) qlogicpti1: [Ultra Wide, using differential interface] scsi4 : PTI Qlogic,ISP SBUS SCSI irq 45 regs at 000001d520010000 qlogicpti2: IRQ 54 SCSI ID 7 qpti f02c9e60: firmware: requesting qlogic/isp1000.bin scsi 3:0:0:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 (Firmware v1.31.32)(FCode 1.28 99/11/08) qlogicpti2: [Ultra Wide, using differential interface] scsi5 : PTI Qlogic,ISP SBUS SCSI irq 54 regs at 000001d700010000 drascsi 3:0:1:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 cut:/scsi 3:0:2:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 # scsi 3:0:3:0: Direct-Access COMPAQ BD036659CC 3B00 PQ: 0 ANSI: 3 scsi 5:0:8:0: Direct-Access SEAGATE ST336607LC 0007 PQ: 0 ANSI: 3 scsi 5:0:9:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 5:0:10:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 scsi 5:0:12:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 3:0:14:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 3:0:0:0: Attached scsi generic sg1 type 0 sd 3:0:1:0: Attached scsi generic sg2 type 0 scsi 5:0:15:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 3:0:0:0: [sda] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 3:0:0:0: [sda] Write Protect is off sd 3:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 3:0:1:0: [sdb] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 3:0:1:0: [sdb] Write Protect is off sda: sd 3:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA sda1 sda2 sda3 sd 3:0:2:0: Attached scsi generic sg3 type 0 sd 3:0:3:0: Attached scsi generic sg4 type 0 sd 3:0:2:0: [sdc] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sdb: sd 3:0:2:0: [sdc] Write Protect is off sd 3:0:3:0: [sdd] 71132000 512-byte logical blocks: (36.4 GB/33.9 GiB) sdb3 sd 3:0:0:0: [sda] Attached SCSI disk sd 3:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 3:0:3:0: [sdd] Write Protect is off scsi 3:0:14:0: Attached scsi generic sg5 type 3 sd 5:0:8:0: Attached scsi generic sg6 type 0 sd 5:0:9:0: Attached scsi generic sg7 type 0 sd 5:0:10:0: Attached scsi generic sg8 type 0 sd 5:0:12:0: Attached scsi generic sg9 type 0 scsi 5:0:15:0: Attached scsi generic sg10 type 3 sd 5:0:8:0: [sde] 71687372 512-byte logical blocks: (36.7 GB/34.1 GiB) sd 5:0:8:0: [sde] Write Protect is off sd 5:0:9:0: [sdf] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 5:0:9:0: [sdf] Write Protect is off sd 3:0:1:0: [sdb] Attached SCSI disk sd 5:0:12:0: [sdh] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 5:0:10:0: [sdg] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 5:0:8:0: [sde] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 5:0:12:0: [sdh] Write Protect is off sd 5:0:10:0: [sdg] Write Protect is off sd 5:0:9:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 5:0:10:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 5:0:12:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 3:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA sdc: sdf: sde: sdh: device-mapper: multipath: version 1.1.0 loaded sdc3 sde3 sdf3 sdg: sdd: sdg3 sd 5:0:8:0: [sde] Attached SCSI disk sdh3 sd 3:0:2:0: [sdc] Attached SCSI disk sdd3 sd 5:0:9:0: [sdf] Attached SCSI disk sd 5:0:12:0: [sdh] Attached SCSI disk sd 3:0:3:0: [sdd] Attached SCSI disk sd 5:0:10:0: [sdg] Attached SCSI disk
dracut:/# lvm vgscan File descriptor 9 (/.console_lock) leaked on lvm invocation. Parent PID 890: sh Reading all physical volumes. This may take a while... Found volume group "vg_spacely" using metadata type lvm2 dracut:/# lvm vgchange -ay File descriptor 9 (/.console_lock) leaked on lvm invocation. Parent PID 890: sh 2 logical volume(s) in volume group "vg_spacely" now active dracut:/# ls /dev/mapper control vg_spacely-lv_root vg_spacely-lv_swap dracut:/# ln -s /dev/mapper/vg_spacely-lv_root /dev/root dracut:/# exit
and the bootup proceeds; it does the SELinux relabel, and brings up the text-mode firstboot, but I can't get an SSH into it, and no getty on the serial console.....more work to do.
Here's the debug dmesg (long!) from a failed boot attempt with rdloaddriver=qlogicpti on the command line: ++++++++++ PROMLIB: Sun IEEE Boot Prom 'OBP 3.2.30 2002/10/25 14:03' PROMLIB: Root node compatible: Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 2.6.32.10-90.fc12.sparc64 (mockbuild@korolev.ausil.us) (gcc version 4.4.3 20100409 (Red Hat 4.4.3-17) (GCC) ) #1 SMP Thu Apr 15 13:30:40 CDT 2010 bootconsole [earlyprom0] enabled ARCH: SUN4U Ethernet address: 08:00:20:bd:ca:05 Kernel: Using 3 locked TLB entries for main kernel image. Remapping the kernel... done. OF stdout device is: /central@1f,0/fhc@0,f8800000/zs@0,902000:a PROM: Built device tree with 159432 bytes of memory. Top of RAM: 0x4ffcf4000, Total RAM: 0x4ff3f2000 Memory hole size: 9MB [0000010000000000-fffff80001000000] page_structs=131072 node=0 entry=0/0 [0000010000000000-fffff80001400000] page_structs=131072 node=0 entry=1/0 [0000010000800000-fffff80001800000] page_structs=131072 node=0 entry=2/0 [0000010000800000-fffff80001c00000] page_structs=131072 node=0 entry=3/0 [0000010001000000-fffff80002000000] page_structs=131072 node=0 entry=4/0 [0000010001000000-fffff80002400000] page_structs=131072 node=0 entry=5/0 [0000010001800000-fffff80002800000] page_structs=131072 node=0 entry=6/0 [0000010001800000-fffff80002c00000] page_structs=131072 node=0 entry=7/0 [0000010002000000-fffff80003000000] page_structs=131072 node=0 entry=8/0 [0000010002000000-fffff80003400000] page_structs=131072 node=0 entry=9/0 [0000010002800000-fffff80003800000] page_structs=131072 node=0 entry=10/0 [0000010002800000-fffff80003c00000] page_structs=131072 node=0 entry=11/0 [0000010003000000-fffff80004000000] page_structs=131072 node=0 entry=12/0 [0000010003000000-fffff80005400000] page_structs=131072 node=0 entry=13/0 [0000010003800000-fffff80005800000] page_structs=131072 node=0 entry=14/0 [0000010003800000-fffff80005c00000] page_structs=131072 node=0 entry=15/0 [0000010004000000-fffff80006000000] page_structs=131072 node=0 entry=16/0 [0000010004000000-fffff80006400000] page_structs=131072 node=0 entry=17/0 [0000010004800000-fffff80006800000] page_structs=131072 node=0 entry=18/0 [0000010004800000-fffff80006c00000] page_structs=131072 node=0 entry=19/0 [0000010005000000-fffff80007000000] page_structs=131072 node=0 entry=20/0 [0000010005000000-fffff80007400000] page_structs=131072 node=0 entry=21/0 [0000010005800000-fffff80007800000] page_structs=131072 node=0 entry=22/0 [0000010005800000-fffff80007c00000] page_structs=131072 node=0 entry=23/0 [0000010006000000-fffff80008000000] page_structs=131072 node=0 entry=24/0 [0000010006000000-fffff80008400000] page_structs=131072 node=0 entry=25/0 [0000010006800000-fffff80008800000] page_structs=131072 node=0 entry=26/0 [0000010006800000-fffff80008c00000] page_structs=131072 node=0 entry=27/0 [0000010007000000-fffff80009000000] page_structs=131072 node=0 entry=28/0 [0000010007000000-fffff80009400000] page_structs=131072 node=0 entry=29/0 [0000010007800000-fffff80009800000] page_structs=131072 node=0 entry=30/0 [0000010007800000-fffff80009c00000] page_structs=131072 node=0 entry=31/0 [0000010008000000-fffff8000a000000] page_structs=131072 node=0 entry=32/0 [0000010008000000-fffff8000a400000] page_structs=131072 node=0 entry=33/0 [0000010008800000-fffff8000a800000] page_structs=131072 node=0 entry=34/0 [0000010008800000-fffff8000ac00000] page_structs=131072 node=0 entry=35/0 [0000010009000000-fffff8000b000000] page_structs=131072 node=0 entry=36/0 [0000010009000000-fffff8000b400000] page_structs=131072 node=0 entry=37/0 [0000010009800000-fffff8000b800000] page_structs=131072 node=0 entry=38/0 [0000010009800000-fffff8000bc00000] page_structs=131072 node=0 entry=39/0 Zone PFN ranges: Normal 0x00000000 -> 0x0027fe7a Movable zone start PFN for each node early_node_map[3] active PFN ranges 0: 0x00000000 -> 0x0027f987 0: 0x0027fe00 -> 0x0027fe65 0: 0x0027fe6d -> 0x0027fe7a On node 0 totalpages: 2619897 Normal zone: 20477 pages used for memmap Normal zone: 0 pages reserved Normal zone: 2599420 pages, LIFO batch:15 Booting Linux... PERCPU: Embedded 7 pages/cpu @fffff8000c000000 s27136 r8192 d22016 u1048576 pcpu-alloc: s27136 r8192 d22016 u1048576 alloc=1*4194304 pcpu-alloc: [0] 00 01 04 05 [0] 08 09 12 13 pcpu-alloc: [0] 16 17 20 21 [0] 24 25 26 27 pcpu-alloc: [0] 28 -- -- -- Built 1 zonelists in Node order, mobility grouping on. Total pages: 2599420 Policy zone: Normal Kernel command line: root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti PID hash table entries: 4096 (order: 2, 32768 bytes) Memory: 20772112k available (4536k kernel code, 2176k data, 400k init) [fffff80000000000,00000004ffcf4000] SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=29, Nodes=16 Hierarchical RCU implementation. NR_IRQS:255 clocksource: mult[28000] shift[16] clockevent: mult[66666666] shift[32] Console: colour dummy device 80x25 allocated 104857600 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Calibrating delay using timer specific routine.. 801.46 BogoMIPS (lpj=4007344) Security Framework initialized SELinux: Initializing. SELinux: Starting in permissive mode Dentry cache hash table entries: 4194304 (order: 12, 33554432 bytes) Inode-cache hash table entries: 2097152 (order: 11, 16777216 bytes) Mount-cache hash table entries: 512 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys net_cls ftrace: allocating 17120 entries in 34 pages CPU 1: synchronized TICK with master CPU (last diff -10 cycles, maxerr 840 cycles) CPU 4: synchronized TICK with master CPU (last diff -1 cycles, maxerr 819 cycles) CPU 5: synchronized TICK with master CPU (last diff -14 cycles, maxerr 870 cycles) CPU 8: synchronized TICK with master CPU (last diff -15 cycles, maxerr 850 cycles) CPU 9: synchronized TICK with master CPU (last diff -3 cycles, maxerr 870 cycles) CPU 12: synchronized TICK with master CPU (last diff 4 cycles, maxerr 819 cycles) CPU 13: synchronized TICK with master CPU (last diff -17 cycles, maxerr 859 cycles) CPU 16: synchronized TICK with master CPU (last diff -20 cycles, maxerr 860 cycles) CPU 17: synchronized TICK with master CPU (last diff 17 cycles, maxerr 826 cycles) CPU 20: synchronized TICK with master CPU (last diff -30 cycles, maxerr 869 cycles) CPU 21: synchronized TICK with master CPU (last diff -3 cycles, maxerr 874 cycles) CPU 24: synchronized TICK with master CPU (last diff -18 cycles, maxerr 869 cycles) CPU 25: synchronized TICK with master CPU (last diff 2 cycles, maxerr 849 cycles) CPU 26: synchronized TICK with master CPU (last diff -17 cycles, maxerr 840 cycles) CPU 27: synchronized TICK with master CPU (last diff 9 cycles, maxerr 882 cycles) CPU 28: synchronized TICK with master CPU (last diff 0 cycles, maxerr 868 cycles) Brought up 17 CPUs sizeof(vma)=176 bytes sizeof(page)=64 bytes sizeof(inode)=584 bytes sizeof(dentry)=192 bytes sizeof(ext3inode)=784 bytes sizeof(buffer_head)=104 bytes sizeof(skbuff)=232 bytes sizeof(task_struct)=5704 bytes CPU0 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 0 1 4 5 8 9 12 13 16 17 20 21 24 25 26 27 28 CPU1 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 1 4 5 8 9 12 13 16 17 20 21 24 25 26 27 28 0 CPU4 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 4 5 8 9 12 13 16 17 20 21 24 25 26 27 28 0 1 CPU5 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 5 8 9 12 13 16 17 20 21 24 25 26 27 28 0 1 4 CPU8 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 8 9 12 13 16 17 20 21 24 25 26 27 28 0 1 4 5 CPU9 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 9 12 13 16 17 20 21 24 25 26 27 28 0 1 4 5 8 CPU12 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 12 13 16 17 20 21 24 25 26 27 28 0 1 4 5 8 9 CPU13 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 13 16 17 20 21 24 25 26 27 28 0 1 4 5 8 9 12 CPU16 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 16 17 20 21 24 25 26 27 28 0 1 4 5 8 9 12 13 CPU17 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 17 20 21 24 25 26 27 28 0 1 4 5 8 9 12 13 16 CPU20 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 20 21 24 25 26 27 28 0 1 4 5 8 9 12 13 16 17 CPU21 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 21 24 25 26 27 28 0 1 4 5 8 9 12 13 16 17 20 CPU24 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 24 25 26 27 28 0 1 4 5 8 9 12 13 16 17 20 21 CPU25 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 25 26 27 28 0 1 4 5 8 9 12 13 16 17 20 21 24 CPU26 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 26 27 28 0 1 4 5 8 9 12 13 16 17 20 21 24 25 CPU27 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 27 28 0 1 4 5 8 9 12 13 16 17 20 21 24 25 26 CPU28 attaching sched-domain: domain 0: span 0-1,4-5,8-9,12-13,16-17,20-21,24-28 level CPU groups: 28 0 1 4 5 8 9 12 13 16 17 20 21 24 25 26 27 devtmpfs: initialized regulator: core version 0.5 NET: Registered protocol family 16 fhc: Board #1, Version[1] PartID[fa0] Manuf[3e] (Central) fhc: Board #0, Version[1] PartID[fa0] Manuf[3e] (JTAG Master) fhc: Board #2, Version[1] PartID[fa0] Manuf[3e] fhc: Board #4, Version[1] PartID[fa0] Manuf[3e] fhc: Board #6, Version[1] PartID[fa0] Manuf[3e] fhc: Board #8, Version[1] PartID[fa0] Manuf[3e] fhc: Board #10, Version[1] PartID[fa0] Manuf[3e] fhc: Board #12, Version[1] PartID[fa0] Manuf[3e] fhc: Board #13, Version[1] PartID[fa0] Manuf[3e] fhc: Board #14, Version[1] PartID[fa0] Manuf[3e] fhc: Board #1, Version[1] PartID[fa0] Manuf[3e] fhc: Board #3, Version[1] PartID[fa0] Manuf[3e] fhc: Board #5, Version[1] PartID[fa0] Manuf[3e] clock_board: Detected 16 slot Enterprise system. SYSIO: UPA portID ffffffff, at 000001c400000000 SYSIO: UPA portID ffffffff, at 000001c600000000 SYSIO: UPA portID ffffffff, at 000001cc00000000 SYSIO: UPA portID ffffffff, at 000001ce00000000 SYSIO: UPA portID ffffffff, at 000001d400000000 SYSIO: UPA portID ffffffff, at 000001d600000000 bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default /central/fhc@0,f8800000/eeprom@0,908000: Mostek regs at 0x1fff8908000 Switching to clocksource tick NET: Registered protocol family 2 IP route cache hash table entries: 524288 (order: 9, 4194304 bytes) TCP established hash table entries: 524288 (order: 10, 8388608 bytes) TCP bind hash table entries: 65536 (order: 7, 1048576 bytes) TCP: Hash tables configured (established 524288 bind 65536) TCP reno registered NET: Registered protocol family 1 Trying to unpack rootfs image as initramfs... Freeing initrd memory: 12727k freed audit: initializing netlink socket (disabled) type=2000 audit(6.873:1): initialized HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 8192 bytes) msgmni has been set to 32768 SELinux: Registering netfilter hooks alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci-stub: invalid id string "" f005de3c: ttyS0 at MMIO 0x1fff8902000 (irq = 2) is a zs (ESCC) Console: ttyS0 (SunZilog zs0) console [ttyS0] enabled, bootconsole disabled f005de3c: ttyS1 at MMIO 0x1fff8902004 (irq = 2) is a zs (ESCC) f005df14: Keyboard at MMIO 0x1fff8904000 (irq = 2) is a zs f005df14: Mouse at MMIO 0x1fff8904004 (irq = 2) is a zs brd: module loaded loop: module loaded Fixed MDIO Bus: probed ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver mice: PS/2 mouse device common for all mice rtc-m48t59 rtc-m48t59.0: rtc core: registered m48t59 as rtc0 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 registered taskstats version 1 rtc-m48t59 rtc-m48t59.0: setting system clock to 2010-06-03 17:25:56 UTC (1275585956) Initalizing network drop monitor service dracut: + mkdir /dev/shm dracut: + mkdir /dev/pts dracut: + mount -t devpts -o gid=5,mode=620 devpts /dev/pts dracut: + mount -t tmpfs tmpfs /dev/shm dracut: + udevadm --version dracut: + UDEVVERSION=145 dracut: + source_conf /etc/conf.d dracut: + local f dracut: + [ /etc/conf.d ] dracut: + [ -d //etc/conf.d ] dracut: + return dracut: + getarg rdbreak=cmdline dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdbreak=cmdline ] dracut: + [ root = rdbreak=cmdline ] dracut: + [ ro = rdbreak=cmdline ] dracut: + [ ro = rdbreak=cmdline ] dracut: + [ LANG=en_US.UTF-8 = rdbreak=cmdline ] dracut: + [ LANG = rdbreak=cmdline ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdbreak=cmdline ] dracut: + [ SYSFONT = rdbreak=cmdline ] dracut: + [ KEYTABLE=us = rdbreak=cmdline ] dracut: + [ KEYTABLE = rdbreak=cmdline ] dracut: + [ console=ttyS0,9600 = rdbreak=cmdline ] dracut: + [ console = rdbreak=cmdline ] dracut: + [ rdinitdebug = rdbreak=cmdline ] dracut: + [ rdinitdebug = rdbreak=cmdline ] dracut: + [ rdshell = rdbreak=cmdline ] dracut: + [ rdshell = rdbreak=cmdline ] dracut: + [ rdloaddriver=sun_esp = rdbreak=cmdline ] dracut: + [ rdloaddriver = rdbreak=cmdline ] dracut: + [ rdloaddriver=qlogicpti = rdbreak=cmdline ] dracut: + [ rdloaddriver = rdbreak=cmdline ] dracut: + return 1 dracut: + source_all cmdline dracut: + local f dracut: + [ cmdline ] dracut: + [ -d /cmdline ] dracut: + [ -e /cmdline/01parse-kernel.sh ] dracut: + . /cmdline/01parse-kernel.sh dracut: + getargs rdloaddriver= dracut: + local o line found dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdloaddriver= ] dracut: + [ root = rdloaddriver ] dracut: + [ ro = rdloaddriver= ] dracut: + [ ro = rdloaddriver ] dracut: + [ LANG=en_US.UTF-8 = rdloaddriver= ] dracut: + [ LANG = rdloaddriver ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdloaddriver= ] dracut: + [ SYSFONT = rdloaddriver ] dracut: + [ KEYTABLE=us = rdloaddriver= ] dracut: + [ KEYTABLE = rdloaddriver ] dracut: + [ console=ttyS0,9600 = rdloaddriver= ] dracut: + [ console = rdloaddriver ] dracut: + [ rdinitdebug = rdloaddriver= ] dracut: + [ rdinitdebug = rdloaddriver ] dracut: + [ rdshell = rdloaddriver= ] dracut: + [ rdshell = rdloaddriver ] dracut: + [ rdloaddriver=sun_esp = rdloaddriver= ] dracut: + [ rdloaddriver = rdloaddriver ] dracut: + echo -n sun_esp dracut: + found=1 dracut: + [ rdloaddriver=qlogicpti = rdloaddriver= ] dracut: + [ rdloaddriver = rdloaddriver ] dracut: + echo -n qlogicpti dracut: + found=1 dracut: + [ -n 1 ] dracut: + return 0 dracut: + modprobe sun_esp esp: esp0, regs[1c738810000:1c738800000] irq[18] esp: esp0 is a FASHME, 40 MHz (ccf=0), SCSI ID 7 scsi0 : esp esp: esp1, regs[1cf38810000:1cf38800000] irq[36] esp: esp1 is a FASHME, 40 MHz (ccf=0), SCSI ID 7 scsi 0:0:6:0: CD-ROM TOSHIBA DVD-ROM SD-M1401 1009 PQ: 0 ANSI: 2 scsi target0:0:6: Beginning Domain Validation scsi target0:0:6: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) scsi target0:0:6: Domain Validation skipping write tests scsi target0:0:6: Ending Domain Validation scsi1 : esp esp: esp2, regs[1d738810000:1d738800000] irq[53] esp: esp2 is a FASHME, 40 MHz (ccf=0), SCSI ID 7 sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 0:0:6:0: Attached scsi CD-ROM sr0 sr 0:0:6:0: Attached scsi generic sg0 type 5 scsi2 : esp dracut: + modprobe qlogicpti qlogicpti0: IRQ 19 SCSI ID 7 qpti f00fccd4: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2 qlogicpti0: IRQ 45 SCSI ID 7 qpti f02b6520: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2 qlogicpti0: IRQ 54 SCSI ID 7 qpti f02c9e60: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2 dracut: + [ -e /cmdline/01version.sh ] dracut: + . /cmdline/01version.sh dracut: + [ -f dracut-004-4.fc12 ] dracut: + vinfo dracut: + read line dracut: + info dracut-004-4.fc12 dracut: + check_quiet dracut: + [ -z ] dracut: + DRACUT_QUIET=yes dracut: + getarg rdinfo dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdinfo ] dracut: + [ root = rdinfo ] dracut: + [ ro = rdinfo ] dracut: + [ ro = rdinfo ] dracut: + [ LANG=en_US.UTF-8 = rdinfo ] dracut: + [ LANG = rdinfo ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdinfo ] dracut: + [ SYSFONT = rdinfo ] dracut: + [ KEYTABLE=us = rdinfo ] dracut: dracut-004-4.fc12 dracut: + [ KEYTABLE = rdinfo ] dracut: + [ console=ttyS0,9600 = rdinfo ] dracut: + [ console = rdinfo ] dracut: + [ rdinitdebug = rdinfo ] dracut: + [ rdinitdebug = rdinfo ] dracut: + [ rdshell = rdinfo ] dracut: + [ rdshell = rdinfo ] dracut: + [ rdloaddriver=sun_esp = rdinfo ] dracut: + [ rdloaddriver = rdinfo ] dracut: + [ rdloaddriver=qlogicpti = rdinfo ] dracut: + [ rdloaddriver = rdinfo ] dracut: + return 1 dracut: + getarg quiet dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = quiet ] dracut: + [ root = quiet ] dracut: + [ ro = quiet ] dracut: + [ ro = quiet ] dracut: + [ LANG=en_US.UTF-8 = quiet ] dracut: + [ LANG = quiet ] dracut: + [ SYSFONT=latarcyrheb-sun16 = quiet ] dracut: + [ SYSFONT = quiet ] dracut: + [ KEYTABLE=us = quiet ] dracut: + [ KEYTABLE = quiet ] dracut: + [ console=ttyS0,9600 = quiet ] dracut: + [ console = quiet ] dracut: + [ rdinitdebug = quiet ] dracut: + [ rdinitdebug = quiet ] dracut: + [ rdshell = quiet ] dracut: + [ rdshell = quiet ] dracut: + [ rdloaddriver=sun_esp = quiet ] dracut: + [ rdloaddriver = quiet ] dracut: + [ rdloaddriver=qlogicpti = quiet ] dracut: + [ rdloaddriver = quiet ] dracut: + return 1 dracut: + DRACUT_QUIET=yes dracut: + echo <6>dracut: dracut-004-4.fc12 dracut: + [ yes != yes ] dracut: + read line dracut: + unset i dracut: + [ -e /cmdline/10parse-resume.sh ] dracut: + . /cmdline/10parse-resume.sh dracut: + getarg resume= dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = resume= ] dracut: + [ root = resume ] dracut: + [ ro = resume= ] dracut: + [ ro = resume ] dracut: + [ LANG=en_US.UTF-8 = resume= ] dracut: + [ LANG = resume ] dracut: + [ SYSFONT=latarcyrheb-sun16 = resume= ] dracut: + [ SYSFONT = resume ] dracut: + [ KEYTABLE=us = resume= ] dracut: + [ KEYTABLE = resume ] dracut: + [ console=ttyS0,9600 = resume= ] dracut: + [ console = resume ] dracut: + [ rdinitdebug = resume= ] dracut: + [ rdinitdebug = resume ] dracut: + [ rdshell = resume= ] dracut: + [ rdshell = resume ] dracut: + [ rdloaddriver=sun_esp = resume= ] dracut: + [ rdloaddriver = resume ] dracut: + [ rdloaddriver=qlogicpti = resume= ] dracut: + [ rdloaddriver = resume ] dracut: + return 1 dracut: + resume= dracut: + unset resume dracut: + [ -e /cmdline/10parse-root-opts.sh ] dracut: + . /cmdline/10parse-root-opts.sh dracut: + getarg root= dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = root= ] dracut: + [ root = root ] dracut: + echo /dev/mapper/vg_spacely-lv_root dracut: + return 0 dracut: + root=/dev/mapper/vg_spacely-lv_root dracut: + getarg rootflags= dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rootflags= ] dracut: + [ root = rootflags ] dracut: + [ ro = rootflags= ] dracut: + [ ro = rootflags ] dracut: + [ LANG=en_US.UTF-8 = rootflags= ] dracut: + [ LANG = rootflags ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rootflags= ] dracut: + [ SYSFONT = rootflags ] dracut: + [ KEYTABLE=us = rootflags= ] dracut: + [ KEYTABLE = rootflags ] dracut: + [ console=ttyS0,9600 = rootflags= ] dracut: + [ console = rootflags ] dracut: + [ rdinitdebug = rootflags= ] dracut: + [ rdinitdebug = rootflags ] dracut: + [ rdshell = rootflags= ] dracut: + [ rdshell = rootflags ] dracut: + [ rdloaddriver=sun_esp = rootflags= ] dracut: + [ rdloaddriver = rootflags ] dracut: + [ rdloaddriver=qlogicpti = rootflags= ] dracut: + [ rdloaddriver = rootflags ] dracut: + return 1 dracut: + rflags= dracut: + getarg rw dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rw ] dracut: + [ root = rw ] dracut: + [ ro = rw ] dracut: + [ ro = rw ] dracut: + [ LANG=en_US.UTF-8 = rw ] dracut: + [ LANG = rw ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rw ] dracut: + [ SYSFONT = rw ] dracut: + [ KEYTABLE=us = rw ] dracut: + [ KEYTABLE = rw ] dracut: + [ console=ttyS0,9600 = rw ] dracut: + [ console = rw ] dracut: + [ rdinitdebug = rw ] dracut: + [ rdinitdebug = rw ] dracut: + [ rdshell = rw ] dracut: + [ rdshell = rw ] dracut: + [ rdloaddriver=sun_esp = rw ] dracut: + [ rdloaddriver = rw ] dracut: + [ rdloaddriver=qlogicpti = rw ] dracut: + [ rdloaddriver = rw ] dracut: + return 1 dracut: + rflags=ro dracut: + getarg rootfstype= dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rootfstype= ] dracut: + [ root = rootfstype ] dracut: + [ ro = rootfstype= ] dracut: + [ ro = rootfstype ] dracut: + [ LANG=en_US.UTF-8 = rootfstype= ] dracut: + [ LANG = rootfstype ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rootfstype= ] dracut: + [ SYSFONT = rootfstype ] dracut: + [ KEYTABLE=us = rootfstype= ] dracut: + [ KEYTABLE = rootfstype ] dracut: + [ console=ttyS0,9600 = rootfstype= ] dracut: + [ console = rootfstype ] dracut: + [ rdinitdebug = rootfstype= ] dracut: + [ rdinitdebug = rootfstype ] dracut: + [ rdshell = rootfstype= ] dracut: + [ rdshell = rootfstype ] dracut: + [ rdloaddriver=sun_esp = rootfstype= ] dracut: + [ rdloaddriver = rootfstype ] dracut: + [ rdloaddriver=qlogicpti = rootfstype= ] dracut: + [ rdloaddriver = rootfstype ] dracut: + return 1 dracut: + fstype= dracut: + [ -z ] dracut: + fstype=auto dracut: + [ -e /cmdline/20parse-blacklist.sh ] dracut: + . /cmdline/20parse-blacklist.sh dracut: + getargs rdblacklist= dracut: + local o line found dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdblacklist= ] dracut: + [ root = rdblacklist ] dracut: + [ ro = rdblacklist= ] dracut: + [ ro = rdblacklist ] dracut: + [ LANG=en_US.UTF-8 = rdblacklist= ] dracut: + [ LANG = rdblacklist ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdblacklist= ] dracut: + [ SYSFONT = rdblacklist ] dracut: + [ KEYTABLE=us = rdblacklist= ] dracut: + [ KEYTABLE = rdblacklist ] dracut: + [ console=ttyS0,9600 = rdblacklist= ] dracut: + [ console = rdblacklist ] dracut: + [ rdinitdebug = rdblacklist= ] dracut: + [ rdinitdebug = rdblacklist ] dracut: + [ rdshell = rdblacklist= ] dracut: + [ rdshell = rdblacklist ] dracut: + [ rdloaddriver=sun_esp = rdblacklist= ] dracut: + [ rdloaddriver = rdblacklist ] dracut: + [ rdloaddriver=qlogicpti = rdblacklist= ] dracut: + [ rdloaddriver = rdblacklist ] dracut: + [ -n ] dracut: + return 1 dracut: + [ -e /cmdline/20parse-i18n.sh ] dracut: + . /cmdline/20parse-i18n.sh dracut: + mkdir -p /etc/sysconfig dracut: + inst_key_val KEYBOARDTYPE /etc/sysconfig/keyboard dracut: + local value dracut: + getarg KEYBOARDTYPE dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = KEYBOARDTYPE ] dracut: + [ root = KEYBOARDTYPE ] dracut: + [ ro = KEYBOARDTYPE ] dracut: + [ ro = KEYBOARDTYPE ] dracut: + [ LANG=en_US.UTF-8 = KEYBOARDTYPE ] dracut: + [ LANG = KEYBOARDTYPE ] dracut: + [ SYSFONT=latarcyrheb-sun16 = KEYBOARDTYPE ] dracut: + [ SYSFONT = KEYBOARDTYPE ] dracut: + [ KEYTABLE=us = KEYBOARDTYPE ] dracut: + [ KEYTABLE = KEYBOARDTYPE ] dracut: + [ console=ttyS0,9600 = KEYBOARDTYPE ] dracut: + [ console = KEYBOARDTYPE ] dracut: + [ rdinitdebug = KEYBOARDTYPE ] dracut: + [ rdinitdebug = KEYBOARDTYPE ] dracut: + [ rdshell = KEYBOARDTYPE ] dracut: + [ rdshell = KEYBOARDTYPE ] dracut: + [ rdloaddriver=sun_esp = KEYBOARDTYPE ] dracut: + [ rdloaddriver = KEYBOARDTYPE ] dracut: + [ rdloaddriver=qlogicpti = KEYBOARDTYPE ] dracut: + [ rdloaddriver = KEYBOARDTYPE ] dracut: + return 1 dracut: + value= dracut: + [ -n ] dracut: + inst_key_val KEYTABLE /etc/sysconfig/keyboard dracut: + local value dracut: + getarg KEYTABLE dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = KEYTABLE ] dracut: + [ root = KEYTABLE ] dracut: + [ ro = KEYTABLE ] dracut: + [ ro = KEYTABLE ] dracut: + [ LANG=en_US.UTF-8 = KEYTABLE ] dracut: + [ LANG = KEYTABLE ] dracut: + [ SYSFONT=latarcyrheb-sun16 = KEYTABLE ] dracut: + [ SYSFONT = KEYTABLE ] dracut: + [ KEYTABLE=us = KEYTABLE ] dracut: + [ KEYTABLE = KEYTABLE ] dracut: + echo us dracut: + return 0 dracut: + value=us dracut: + [ -n us ] dracut: + printf %s="%s"n KEYTABLE us dracut: + inst_key_val SYSFONT /etc/sysconfig/i18n dracut: + local value dracut: + getarg SYSFONT dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = SYSFONT ] dracut: + [ root = SYSFONT ] dracut: + [ ro = SYSFONT ] dracut: + [ ro = SYSFONT ] dracut: + [ LANG=en_US.UTF-8 = SYSFONT ] dracut: + [ LANG = SYSFONT ] dracut: + [ SYSFONT=latarcyrheb-sun16 = SYSFONT ] dracut: + [ SYSFONT = SYSFONT ] dracut: + echo latarcyrheb-sun16 dracut: + return 0 dracut: + value=latarcyrheb-sun16 dracut: + [ -n latarcyrheb-sun16 ] dracut: + printf %s="%s"n SYSFONT latarcyrheb-sun16 dracut: + inst_key_val SYSFONTACM /etc/sysconfig/i18n dracut: + local value dracut: + getarg SYSFONTACM dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = SYSFONTACM ] dracut: + [ root = SYSFONTACM ] dracut: + [ ro = SYSFONTACM ] dracut: + [ ro = SYSFONTACM ] dracut: + [ LANG=en_US.UTF-8 = SYSFONTACM ] dracut: + [ LANG = SYSFONTACM ] dracut: + [ SYSFONT=latarcyrheb-sun16 = SYSFONTACM ] dracut: + [ SYSFONT = SYSFONTACM ] dracut: + [ KEYTABLE=us = SYSFONTACM ] dracut: + [ KEYTABLE = SYSFONTACM ] dracut: + [ console=ttyS0,9600 = SYSFONTACM ] dracut: + [ console = SYSFONTACM ] dracut: + [ rdinitdebug = SYSFONTACM ] dracut: + [ rdinitdebug = SYSFONTACM ] dracut: + [ rdshell = SYSFONTACM ] dracut: + [ rdshell = SYSFONTACM ] dracut: + [ rdloaddriver=sun_esp = SYSFONTACM ] dracut: + [ rdloaddriver = SYSFONTACM ] dracut: + [ rdloaddriver=qlogicpti = SYSFONTACM ] dracut: + [ rdloaddriver = SYSFONTACM ] dracut: + return 1 dracut: + value= dracut: + [ -n ] dracut: + inst_key_val UNIMAP /etc/sysconfig/i18n dracut: + local value dracut: + getarg UNIMAP dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = UNIMAP ] dracut: + [ root = UNIMAP ] dracut: + [ ro = UNIMAP ] dracut: + [ ro = UNIMAP ] dracut: + [ LANG=en_US.UTF-8 = UNIMAP ] dracut: + [ LANG = UNIMAP ] dracut: + [ SYSFONT=latarcyrheb-sun16 = UNIMAP ] dracut: + [ SYSFONT = UNIMAP ] dracut: + [ KEYTABLE=us = UNIMAP ] dracut: + [ KEYTABLE = UNIMAP ] dracut: + [ console=ttyS0,9600 = UNIMAP ] dracut: + [ console = UNIMAP ] dracut: + [ rdinitdebug = UNIMAP ] dracut: + [ rdinitdebug = UNIMAP ] dracut: + [ rdshell = UNIMAP ] dracut: + [ rdshell = UNIMAP ] dracut: + [ rdloaddriver=sun_esp = UNIMAP ] dracut: + [ rdloaddriver = UNIMAP ] dracut: + [ rdloaddriver=qlogicpti = UNIMAP ] dracut: + [ rdloaddriver = UNIMAP ] dracut: + return 1 dracut: + value= dracut: + [ -n ] dracut: + inst_key_val LANG /etc/sysconfig/i18n dracut: + local value dracut: + getarg LANG dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = LANG ] dracut: + [ root = LANG ] dracut: + [ ro = LANG ] dracut: + [ ro = LANG ] dracut: + [ LANG=en_US.UTF-8 = LANG ] dracut: + [ LANG = LANG ] dracut: + echo en_US.UTF-8 dracut: + return 0 dracut: + value=en_US.UTF-8 dracut: + [ -n en_US.UTF-8 ] dracut: + printf %s="%s"n LANG en_US.UTF-8 dracut: + [ -f /etc/sysconfig/i18n ] dracut: + . /etc/sysconfig/i18n dracut: + SYSFONT=latarcyrheb-sun16 dracut: + LANG=en_US.UTF-8 dracut: + export LANG dracut: + [ -e /cmdline/30parse-crypt.sh ] dracut: + . /cmdline/30parse-crypt.sh dracut: + getarg rd_NO_LUKS dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_LUKS ] dracut: + [ root = rd_NO_LUKS ] dracut: + [ ro = rd_NO_LUKS ] dracut: + [ ro = rd_NO_LUKS ] dracut: + [ LANG=en_US.UTF-8 = rd_NO_LUKS ] dracut: + [ LANG = rd_NO_LUKS ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_NO_LUKS ] dracut: + [ SYSFONT = rd_NO_LUKS ] dracut: + [ KEYTABLE=us = rd_NO_LUKS ] dracut: + [ KEYTABLE = rd_NO_LUKS ] dracut: + [ console=ttyS0,9600 = rd_NO_LUKS ] dracut: + [ console = rd_NO_LUKS ] dracut: + [ rdinitdebug = rd_NO_LUKS ] dracut: + [ rdinitdebug = rd_NO_LUKS ] dracut: + [ rdshell = rd_NO_LUKS ] dracut: + [ rdshell = rd_NO_LUKS ] dracut: + [ rdloaddriver=sun_esp = rd_NO_LUKS ] dracut: + [ rdloaddriver = rd_NO_LUKS ] dracut: + [ rdloaddriver=qlogicpti = rd_NO_LUKS ] dracut: + [ rdloaddriver = rd_NO_LUKS ] dracut: + return 1 dracut: + [ -e /cmdline/30parse-dmsquash-live.sh ] dracut: + . /cmdline/30parse-dmsquash-live.sh dracut: + [ -z /dev/mapper/vg_spacely-lv_root ] dracut: + getarg liveimg dracut: + local o line udev: starting version 145 dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = liveimg ] dracut: + [ root = liveimg ] dracut: + [ ro = liveimg ] dracut: + [ ro = liveimg ] dracut: + [ LANG=en_US.UTF-8 = liveimg ] dracut: + [ LANG = liveimg ] dracut: + [ SYSFONT=latarcyrheb-sun16 = liveimg ] dracut: + [ SYSFONT = liveimg ] dracut: + [ KEYTABLE=us = liveimg ] dracut: + [ KEYTABLE = liveimg ] dracut: + [ console=ttyS0,9600 = liveimg ] dracut: + [ console = liveimg ] dracut: + [ rdinitdebug = liveimg ] dracut: + [ rdinitdebug = liveimg ] dracut: + [ rdshell = liveimg ] dracut: + [ rdshell = liveimg ] dracut: + [ rdloaddriver=sun_esp = liveimg ] dracut: + [ rdloaddriver = liveimg ] dracut: + [ rdloaddriver=qlogicpti = liveimg ] dracut: + [ rdloaddriver = liveimg ] dracut: + return 1 dracut: + [ /dev/mapper/vg_spacely-lv_root = live ] dracut: + [ = live ] dracut: + return dracut: + [ -e /cmdline/30parse-lvm.sh ] dracut: + . /cmdline/30parse-lvm.sh dracut: + getarg rd_NO_LVM dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_LVM ] dracut: + [ root = rd_NO_LVM ] dracut: + [ ro = rd_NO_LVM ] dracut: + [ ro = rd_NO_LVM ] dracut: + [ LANG=en_US.UTF-8 = rd_NO_LVM ] dracut: + [ LANG = rd_NO_LVM ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_NO_LVM ] dracut: + [ SYSFONT = rd_NO_LVM ] dracut: + [ KEYTABLE=us = rd_NO_LVM ] dracut: + [ KEYTABLE = rd_NO_LVM ] dracut: + [ console=ttyS0,9600 = rd_NO_LVM ] dracut: + [ console = rd_NO_LVM ] dracut: + [ rdinitdebug = rd_NO_LVM ] dracut: + [ rdinitdebug = rd_NO_LVM ] dracut: + [ rdshell = rd_NO_LVM ] dracut: + [ rdshell = rd_NO_LVM ] dracut: + [ rdloaddriver=sun_esp = rd_NO_LVM ] dracut: + [ rdloaddriver = rd_NO_LVM ] dracut: + [ rdloaddriver=qlogicpti = rd_NO_LVM ] dracut: + [ rdloaddriver = rd_NO_LVM ] dracut: + return 1 dracut: + [ -e /etc/lvm/lvm.conf ] dracut: + getarg rd_NO_LVMCONF dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_LVMCONF ] dracut: + [ root = rd_NO_LVMCONF ] dracut: + [ ro = rd_NO_LVMCONF ] dracut: + [ ro = rd_NO_LVMCONF ] dracut: + [ LANG=en_US.UTF-8 = rd_NO_LVMCONF ] dracut: + [ LANG = rd_NO_LVMCONF ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_NO_LVMCONF ] dracut: + [ SYSFONT = rd_NO_LVMCONF ] dracut: + [ KEYTABLE=us = rd_NO_LVMCONF ] dracut: + [ KEYTABLE = rd_NO_LVMCONF ] dracut: + [ console=ttyS0,9600 = rd_NO_LVMCONF ] dracut: + [ console = rd_NO_LVMCONF ] dracut: + [ rdinitdebug = rd_NO_LVMCONF ] dracut: + [ rdinitdebug = rd_NO_LVMCONF ] dracut: + [ rdshell = rd_NO_LVMCONF ] dracut: + [ rdshell = rd_NO_LVMCONF ] dracut: + [ rdloaddriver=sun_esp = rd_NO_LVMCONF ] dracut: + [ rdloaddriver = rd_NO_LVMCONF ] dracut: + [ rdloaddriver=qlogicpti = rd_NO_LVMCONF ] dracut: + [ rdloaddriver = rd_NO_LVMCONF ] dracut: + return 1 dracut: + [ -e /cmdline/95parse-block.sh ] dracut: + . /cmdline/95parse-block.sh dracut: + root=block:/dev/mapper/vg_spacely-lv_root dracut: + rootok=1 dracut: + [ -z block:/dev/mapper/vg_spacely-lv_root ] dracut: + [ -z 1 ] dracut: + echo root='block:/dev/mapper/vg_spacely-lv_root' dracut: + echo rflags='ro' dracut: + echo fstype='auto' dracut: + echo netroot='' dracut: + echo NEWROOT='/sysroot' dracut: + getarg rdbreak=pre-udev dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdbreak=pre-udev ] dracut: + [ root = rdbreak=pre-udev ] dracut: + [ ro = rdbreak=pre-udev ] dracut: + [ ro = rdbreak=pre-udev ] dracut: + [ LANG=en_US.UTF-8 = rdbreak=pre-udev ] dracut: + [ LANG = rdbreak=pre-udev ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdbreak=pre-udev ] dracut: + [ SYSFONT = rdbreak=pre-udev ] dracut: + [ KEYTABLE=us = rdbreak=pre-udev ] dracut: + [ KEYTABLE = rdbreak=pre-udev ] dracut: + [ console=ttyS0,9600 = rdbreak=pre-udev ] dracut: + [ console = rdbreak=pre-udev ] dracut: + [ rdinitdebug = rdbreak=pre-udev ] dracut: + [ rdinitdebug = rdbreak=pre-udev ] dracut: + [ rdshell = rdbreak=pre-udev ] dracut: + [ rdshell = rdbreak=pre-udev ] dracut: + [ rdloaddriver=sun_esp = rdbreak=pre-udev ] dracut: + [ rdloaddriver = rdbreak=pre-udev ] dracut: + [ rdloaddriver=qlogicpti = rdbreak=pre-udev ] dracut: + [ rdloaddriver = rdbreak=pre-udev ] dracut: + return 1 dracut: + source_all pre-udev dracut: + local f dracut: + [ pre-udev ] dracut: + [ -d /pre-udev ] dracut: + [ -e /pre-udev/30block-genrules.sh ] dracut: + . /pre-udev/30block-genrules.sh dracut: + [ block = block ] dracut: + printf KERNEL=="%s", SYMLINK+="root"n mapper/vg_spacely-lv_root dracut: + printf SYMLINK=="%s", SYMLINK+="root"n mapper/vg_spacely-lv_root dracut: + printf [ -e "%s" ] && { ln -s "%s" /dev/root 2>/dev/null; rm "$job"; }n /dev/mapper/vg_spacely-lv_root /dev/mapper/vg_spacely-lv_root dracut: + echo [ -e /dev/root ] dracut: + [ -e /pre-udev/30dmsquash-live-genrules.sh ] dracut: + . /pre-udev/30dmsquash-live-genrules.sh dracut: + [ block = live ] dracut: + [ -e /pre-udev/30dmsquash-liveiso-genrules.sh ] dracut: + . /pre-udev/30dmsquash-liveiso-genrules.sh dracut: + [ block = liveiso ] dracut: + [ -e /pre-udev/30mdmon-pre-udev.sh ] dracut: + . /pre-udev/30mdmon-pre-udev.sh dracut: + mkdir /dev/.mdadm dracut: + [ -e /var/run/mdadm ] dracut: + ln -s /dev/.mdadm /var/run/mdadm dracut: + [ -e /pre-udev/30resume-genrules.sh ] dracut: + . /pre-udev/30resume-genrules.sh dracut: + [ -n ] dracut: + getarg noresume dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = noresume ] dracut: + [ root = noresume ] dracut: + [ ro = noresume ] dracut: + [ ro = noresume ] dracut: + [ LANG=en_US.UTF-8 = noresume ] dracut: + [ LANG = noresume ] dracut: + [ SYSFONT=latarcyrheb-sun16 = noresume ] dracut: + [ SYSFONT = noresume ] dracut: + [ KEYTABLE=us = noresume ] dracut: + [ KEYTABLE = noresume ] dracut: + [ console=ttyS0,9600 = noresume ] dracut: + [ console = noresume ] dracut: + [ rdinitdebug = noresume ] dracut: + [ rdinitdebug = noresume ] dracut: + [ rdshell = noresume ] dracut: + [ rdshell = noresume ] dracut: + [ rdloaddriver=sun_esp = noresume ] dracut: + [ rdloaddriver = noresume ] dracut: + [ rdloaddriver=qlogicpti = noresume ] dracut: + [ rdloaddriver = noresume ] dracut: + return 1 dracut: + echo SUBSYSTEM=="block", ACTION=="add|change", ENV{ID_FS_TYPE}=="suspend|swsuspend|swsupend", RUN+="/bin/sh -c 'echo %M:%m > /sys/power/resume'" dracut: + udevd --daemon --resolve-names=never dracut: + UDEV_LOG_PRIO_ARG=--log-priority dracut: + UDEV_QUEUE_EMPTY=udevadm settle --timeout=0 dracut: + [ 145 -lt 140 ] dracut: + getarg rdudevinfo dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdudevinfo ] dracut: + [ root = rdudevinfo ] dracut: + [ ro = rdudevinfo ] dracut: + [ ro = rdudevinfo ] dracut: + [ LANG=en_US.UTF-8 = rdudevinfo ] dracut: + [ LANG = rdudevinfo ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdudevinfo ] dracut: + [ SYSFONT = rdudevinfo ] dracut: + [ KEYTABLE=us = rdudevinfo ] dracut: + [ KEYTABLE = rdudevinfo ] dracut: + [ console=ttyS0,9600 = rdudevinfo ] dracut: + [ console = rdudevinfo ] dracut: + [ rdinitdebug = rdudevinfo ] dracut: + [ rdinitdebug = rdudevinfo ] dracut: + [ rdshell = rdudevinfo ] dracut: + [ rdshell = rdudevinfo ] dracut: + [ rdloaddriver=sun_esp = rdudevinfo ] dracut: + [ rdloaddriver = rdudevinfo ] dracut: + [ rdloaddriver=qlogicpti = rdudevinfo ] dracut: + [ rdloaddriver = rdudevinfo ] dracut: + return 1 dracut: + getarg rdudevdebug dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdudevdebug ] dracut: + [ root = rdudevdebug ] dracut: + [ ro = rdudevdebug ] dracut: + [ ro = rdudevdebug ] dracut: + [ LANG=en_US.UTF-8 = rdudevdebug ] dracut: + [ LANG = rdudevdebug ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdudevdebug ] dracut: + [ SYSFONT = rdudevdebug ] dracut: + [ KEYTABLE=us = rdudevdebug ] dracut: + [ KEYTABLE = rdudevdebug ] dracut: + [ console=ttyS0,9600 = rdudevdebug ] dracut: + [ console = rdudevdebug ] dracut: + [ rdinitdebug = rdudevdebug ] dracut: + [ rdinitdebug = rdudevdebug ] dracut: + [ rdshell = rdudevdebug ] dracut: + [ rdshell = rdudevdebug ] dracut: + [ rdloaddriver=sun_esp = rdudevdebug ] dracut: + [ rdloaddriver = rdudevdebug ] dracut: + [ rdloaddriver=qlogicpti = rdudevdebug ] dracut: + [ rdloaddriver = rdudevdebug ] dracut: + return 1 dracut: + getarg rdbreak=pre-trigger dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdbreak=pre-trigger ] dracut: + [ root = rdbreak=pre-trigger ] dracut: + [ ro = rdbreak=pre-trigger ] dracut: + [ ro = rdbreak=pre-trigger ] dracut: + [ LANG=en_US.UTF-8 = rdbreak=pre-trigger ] dracut: + [ LANG = rdbreak=pre-trigger ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdbreak=pre-trigger ] dracut: + [ SYSFONT = rdbreak=pre-trigger ] dracut: + [ KEYTABLE=us = rdbreak=pre-trigger ] dracut: + [ KEYTABLE = rdbreak=pre-trigger ] dracut: + [ console=ttyS0,9600 = rdbreak=pre-trigger ] dracut: + [ console = rdbreak=pre-trigger ] dracut: + [ rdinitdebug = rdbreak=pre-trigger ] dracut: + [ rdinitdebug = rdbreak=pre-trigger ] dracut: + [ rdshell = rdbreak=pre-trigger ] dracut: + [ rdshell = rdbreak=pre-trigger ] dracut: + [ rdloaddriver=sun_esp = rdbreak=pre-trigger ] dracut: + [ rdloaddriver = rdbreak=pre-trigger ] dracut: + [ rdloaddriver=qlogicpti = rdbreak=pre-trigger ] dracut: + [ rdloaddriver = rdbreak=pre-trigger ] dracut: + return 1 dracut: + source_all pre-trigger dracut: + local f dracut: + [ pre-trigger ] dracut: + [ -d /pre-trigger ] dracut: + [ -e /pre-trigger/02multipathd.sh ] dracut: + . /pre-trigger/02multipathd.sh dracut: + [ -e /etc/multipath.conf ] dracut: + [ -e /pre-trigger/10plymouth-pretrigger.sh ] dracut: + . /pre-trigger/10plymouth-pretrigger.sh dracut: + getarg rd_NO_PLYMOUTH dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_PLYMOUTH ] dracut: + [ root = rd_NO_PLYMOUTH ] dracut: + [ ro = rd_NO_PLYMOUTH ] dracut: + [ ro = rd_NO_PLYMOUTH ] dracut: + [ LANG=en_US.UTF-8 = rd_NO_PLYMOUTH ] dracut: + [ LANG = rd_NO_PLYMOUTH ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_NO_PLYMOUTH ] dracut: + [ SYSFONT = rd_NO_PLYMOUTH ] dracut: + [ KEYTABLE=us = rd_NO_PLYMOUTH ] dracut: + [ KEYTABLE = rd_NO_PLYMOUTH ] dracut: + [ console=ttyS0,9600 = rd_NO_PLYMOUTH ] dracut: + [ console = rd_NO_PLYMOUTH ] dracut: + [ rdinitdebug = rd_NO_PLYMOUTH ] dracut: + [ rdinitdebug = rd_NO_PLYMOUTH ] dracut: + [ rdshell = rd_NO_PLYMOUTH ] dracut: + [ rdshell = rd_NO_PLYMOUTH ] dracut: + [ rdloaddriver=sun_esp = rd_NO_PLYMOUTH ] dracut: + [ rdloaddriver = rd_NO_PLYMOUTH ] dracut: + [ rdloaddriver=qlogicpti = rd_NO_PLYMOUTH ] dracut: + [ rdloaddriver = rd_NO_PLYMOUTH ] dracut: + return 1 dracut: + [ -c /dev/null ] dracut: + udevadm trigger --attr-match=class=0x030000 dracut: + udevadm trigger --subsystem-match=graphics --subsystem-match=drm --subsystem-match=tty dracut: + udevadm settle --timeout=30 dracut: + vinfo dracut: + read line dracut: + [ -c /dev/zero ] dracut: + [ -c /dev/systty ] dracut: + mknod /dev/systty c 4 0 dracut: + [ -c /dev/fb ] dracut: + mknod /dev/fb c 29 0 dracut: + [ -c /dev/hvc0 ] dracut: + mknod /dev/hvc0 c 229 0 dracut: + info Starting plymouth daemon dracut: Starting plymouth daemon dracut: + check_quiet dracut: + [ -z yes ] dracut: + echo <6>dracut: Starting plymouth daemon dracut: + [ yes != yes ] dracut: + [ -x /bin/plymouthd ] dracut: + /bin/plymouthd --attach-to-session dracut: + /lib/udev/console_init tty0 dracut: + /bin/plymouth --show-splash dracut: + vinfo dracut: + read line dracut: + [ -e /pre-trigger/30parse-dm.sh ] dracut: + . /pre-trigger/30parse-dm.sh dracut: + getarg rd_NO_DM dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_DM ] dracut: + [ root = rd_NO_DM ] dracut: + [ ro = rd_NO_DM ] dracut: + [ ro = rd_NO_DM ] dracut: + [ LANG=en_US.UTF-8 = rd_NO_DM ] dracut: + [ LANG = rd_NO_DM ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_NO_DM ] dracut: + [ SYSFONT = rd_NO_DM ] dracut: + [ KEYTABLE=us = rd_NO_DM ] dracut: + [ KEYTABLE = rd_NO_DM ] dracut: + [ console=ttyS0,9600 = rd_NO_DM ] dracut: + [ console = rd_NO_DM ] dracut: + [ rdinitdebug = rd_NO_DM ] dracut: + [ rdinitdebug = rd_NO_DM ] dracut: + [ rdshell = rd_NO_DM ] dracut: + [ rdshell = rd_NO_DM ] dracut: + [ rdloaddriver=sun_esp = rd_NO_DM ] dracut: + [ rdloaddriver = rd_NO_DM ] dracut: + [ rdloaddriver=qlogicpti = rd_NO_DM ] dracut: + [ rdloaddriver = rd_NO_DM ] dracut: + return 1 dracut: + getarg nodmraid dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = nodmraid ] dracut: + [ root = nodmraid ] dracut: + [ ro = nodmraid ] dracut: + [ ro = nodmraid ] dracut: + [ LANG=en_US.UTF-8 = nodmraid ] dracut: + [ LANG = nodmraid ] dracut: + [ SYSFONT=latarcyrheb-sun16 = nodmraid ] dracut: + [ SYSFONT = nodmraid ] dracut: + [ KEYTABLE=us = nodmraid ] dracut: + [ KEYTABLE = nodmraid ] dracut: + [ console=ttyS0,9600 = nodmraid ] dracut: + [ console = nodmraid ] dracut: + [ rdinitdebug = nodmraid ] dracut: + [ rdinitdebug = nodmraid ] dracut: + [ rdshell = nodmraid ] dracut: + [ rdshell = nodmraid ] dracut: + [ rdloaddriver=sun_esp = nodmraid ] dracut: + [ rdloaddriver = nodmraid ] dracut: + [ rdloaddriver=qlogicpti = nodmraid ] dracut: + [ rdloaddriver = nodmraid ] dracut: + return 1 dracut: + [ -e /pre-trigger/30parse-md.sh ] dracut: + . /pre-trigger/30parse-md.sh dracut: + getarg rd_NO_MD dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_MD ] dracut: + [ root = rd_NO_MD ] dracut: + [ ro = rd_NO_MD ] dracut: + [ ro = rd_NO_MD ] dracut: + [ LANG=en_US.UTF-8 = rd_NO_MD ] dracut: + [ LANG = rd_NO_MD ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_NO_MD ] dracut: + [ SYSFONT = rd_NO_MD ] dracut: + [ KEYTABLE=us = rd_NO_MD ] dracut: + [ KEYTABLE = rd_NO_MD ] dracut: + [ console=ttyS0,9600 = rd_NO_MD ] dracut: + [ console = rd_NO_MD ] dracut: + [ rdinitdebug = rd_NO_MD ] dracut: + [ rdinitdebug = rd_NO_MD ] dracut: + [ rdshell = rd_NO_MD ] dracut: + [ rdshell = rd_NO_MD ] dracut: + [ rdloaddriver=sun_esp = rd_NO_MD ] dracut: + [ rdloaddriver = rd_NO_MD ] dracut: + [ rdloaddriver=qlogicpti = rd_NO_MD ] dracut: + [ rdloaddriver = rd_NO_MD ] dracut: + return 1 dracut: + getargs rd_MD_UUID= dracut: + local o line found dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_MD_UUID= ] dracut: + [ root = rd_MD_UUID ] dracut: + [ ro = rd_MD_UUID= ] dracut: + [ ro = rd_MD_UUID ] dracut: + [ LANG=en_US.UTF-8 = rd_MD_UUID= ] dracut: + [ LANG = rd_MD_UUID ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_MD_UUID= ] dracut: + [ SYSFONT = rd_MD_UUID ] dracut: + [ KEYTABLE=us = rd_MD_UUID= ] dracut: + [ KEYTABLE = rd_MD_UUID ] dracut: + [ console=ttyS0,9600 = rd_MD_UUID= ] dracut: + [ console = rd_MD_UUID ] dracut: + [ rdinitdebug = rd_MD_UUID= ] dracut: + [ rdinitdebug = rd_MD_UUID ] dracut: + [ rdshell = rd_MD_UUID= ] dracut: + [ rdshell = rd_MD_UUID ] dracut: + [ rdloaddriver=sun_esp = rd_MD_UUID= ] dracut: + [ rdloaddriver = rd_MD_UUID ] dracut: + [ rdloaddriver=qlogicpti = rd_MD_UUID= ] dracut: + [ rdloaddriver = rd_MD_UUID ] dracut: + [ -n ] dracut: + return 1 dracut: + MD_UUID= dracut: + [ -n ] dracut: + [ -e /etc/mdadm.conf ] dracut: + getarg rd_NO_MDIMSM dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_MDIMSM ] dracut: + [ root = rd_NO_MDIMSM ] dracut: + [ ro = rd_NO_MDIMSM ] dracut: + [ ro = rd_NO_MDIMSM ] dracut: + [ LANG=en_US.UTF-8 = rd_NO_MDIMSM ] dracut: + [ LANG = rd_NO_MDIMSM ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rd_NO_MDIMSM ] dracut: + [ SYSFONT = rd_NO_MDIMSM ] dracut: + [ KEYTABLE=us = rd_NO_MDIMSM ] dracut: + [ KEYTABLE = rd_NO_MDIMSM ] dracut: + [ console=ttyS0,9600 = rd_NO_MDIMSM ] dracut: + [ console = rd_NO_MDIMSM ] dracut: + [ rdinitdebug = rd_NO_MDIMSM ] dracut: + [ rdinitdebug = rd_NO_MDIMSM ] dracut: + [ rdshell = rd_NO_MDIMSM ] dracut: + [ rdshell = rd_NO_MDIMSM ] dracut: + [ rdloaddriver=sun_esp = rd_NO_MDIMSM ] dracut: + [ rdloaddriver = rd_NO_MDIMSM ] dracut: + [ rdloaddriver=qlogicpti = rd_NO_MDIMSM ] dracut: + [ rdloaddriver = rd_NO_MDIMSM ] dracut: + return 1 dracut: + getarg noiswmd dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = noiswmd ] dracut: + [ root = noiswmd ] dracut: + [ ro = noiswmd ] dracut: + [ ro = noiswmd ] dracut: + [ LANG=en_US.UTF-8 = noiswmd ] dracut: + [ LANG = noiswmd ] dracut: + [ SYSFONT=latarcyrheb-sun16 = noiswmd ] dracut: + [ SYSFONT = noiswmd ] dracut: + [ KEYTABLE=us = noiswmd ] dracut: + [ KEYTABLE = noiswmd ] dracut: + [ console=ttyS0,9600 = noiswmd ] dracut: + [ console = noiswmd ] dracut: + [ rdinitdebug = noiswmd ] dracut: + [ rdinitdebug = noiswmd ] dracut: + [ rdshell = noiswmd ] dracut: + [ rdshell = noiswmd ] dracut: + [ rdloaddriver=sun_esp = noiswmd ] dracut: + [ rdloaddriver = noiswmd ] dracut: + [ rdloaddriver=qlogicpti = noiswmd ] dracut: + [ rdloaddriver = noiswmd ] dracut: + return 1 dracut: + getarg nodmraid dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = nodmraid ] dracut: + [ root = nodmraid ] dracut: + [ ro = nodmraid ] dracut: + [ ro = nodmraid ] dracut: + [ LANG=en_US.UTF-8 = nodmraid ] dracut: + [ LANG = nodmraid ] dracut: + [ SYSFONT=latarcyrheb-sun16 = nodmraid ] dracut: + [ SYSFONT = nodmraid ] dracut: + [ KEYTABLE=us = nodmraid ] dracut: + [ KEYTABLE = nodmraid ] dracut: + [ console=ttyS0,9600 = nodmraid ] dracut: + [ console = nodmraid ] dracut: + [ rdinitdebug = nodmraid ] dracut: + [ rdinitdebug = nodmraid ] dracut: + [ rdshell = nodmraid ] dracut: + [ rdshell = nodmraid ] dracut: + [ rdloaddriver=sun_esp = nodmraid ] dracut: + [ rdloaddriver = nodmraid ] dracut: + [ rdloaddriver=qlogicpti = nodmraid ] dracut: + [ rdloaddriver = nodmraid ] dracut: + return 1 dracut: + udevadm trigger dracut: + getarg rdbreak=initqueue dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdbreak=initqueue ] dracut: + [ root = rdbreak=initqueue ] dracut: + [ ro = rdbreak=initqueue ] dracut: + [ ro = rdbreak=initqueue ] dracut: + [ LANG=en_US.UTF-8 = rdbreak=initqueue ] dracut: + [ LANG = rdbreak=initqueue ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdbreak=initqueue ] dracut: + [ SYSFONT = rdbreak=initqueue ] dracut: + [ KEYTABLE=us = rdbreak=initqueue ] dracut: + [ KEYTABLE = rdbreak=initqueue ] dracut: + [ console=ttyS0,9600 = rdbreak=initqueue ] dracut: + [ console = rdbreak=initqueue ] dracut: + [ rdinitdebug = rdbreak=initqueue ] dracut: + [ rdinitdebug = rdbreak=initqueue ] dracut: + [ rdshell = rdbreak=initqueue ] dracut: + [ rdshell = rdbreak=initqueue ] dracut: + [ rdloaddriver=sun_esp = rdbreak=initqueue ] dracut: + [ rdloaddriver = rdbreak=initqueue ] dracut: + [ rdloaddriver=qlogicpti = rdbreak=initqueue ] dracut: + [ rdloaddriver = rdbreak=initqueue ] dracut: + return 1 dracut: + i=0 dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=1 dracut: + [ 1 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=2 dracut: + [ 2 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=3 dracut: + [ 3 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=4 dracut: + [ 4 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=5 dracut: + [ 5 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=6 dracut: + [ 6 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=7 dracut: + [ 7 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=8 dracut: + [ 8 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=9 dracut: + [ 9 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=10 dracut: + [ 10 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=11 dracut: + [ 11 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=12 dracut: + [ 12 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=13 dracut: + [ 13 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=14 dracut: + [ 14 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=15 dracut: + [ 15 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=16 dracut: + [ 16 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=17 dracut: + [ 17 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=18 dracut: + [ 18 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=19 dracut: + [ 19 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=20 dracut: + [ 20 -gt 20 ] dracut: + : dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevsettle dracut: + [ -z 145 ] dracut: + [ 145 -ge 143 ] dracut: + udevadm settle --exit-if-exists=/initqueue/work dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + [ -f /initqueue/work ] dracut: + [ -e /initqueue/*.sh ] dracut: + break dracut: + udevadm settle --timeout=0 dracut: + modprobe scsi_wait_scan dracut: + rmmod scsi_wait_scan dracut: + udevadm settle --timeout=0 dracut: + [ -e /initqueue-settled/blocksymlink.sh ] dracut: + job=/initqueue-settled/blocksymlink.sh . /initqueue-settled/blocksymlink.sh dracut: + [ -e /dev/mapper/vg_spacely-lv_root ] dracut: + check_finished dracut: + local f dracut: + [ -e /initqueue-finished/block.sh ] dracut: + . /initqueue-finished/block.sh dracut: + [ -e /dev/root ] dracut: + return 1 dracut: + udevadm settle --timeout=0 dracut: + sleep 0.5 dracut: + i=21 dracut: + [ 21 -gt 20 ] dracut: + flock -s 9 dracut: + emergency_shell No root device found dracut: + [ No root device found = -n ] dracut: + _rdshell_name=dracut dracut: + wait_for_loginit dracut: + getarg rdinitdebug dracut: + local o line dracut: + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp rdloaddriver=qlogicpti ] dracut: + [ root=/dev/mapper/vg_spacely-lv_root = rdinitdebug ] dracut: + [ root = rdinitdebug ] dracut: + [ ro = rdinitdebug ] dracut: + [ ro = rdinitdebug ] dracut: + [ LANG=en_US.UTF-8 = rdinitdebug ] dracut: + [ LANG = rdinitdebug ] dracut: + [ SYSFONT=latarcyrheb-sun16 = rdinitdebug ] dracut: + [ SYSFONT = rdinitdebug ] dracut: + [ KEYTABLE=us = rdinitdebug ] dracut: + [ KEYTABLE = rdinitdebug ] dracut: + [ console=ttyS0,9600 = rdinitdebug ] dracut: + [ console = rdinitdebug ] dracut: + [ rdinitdebug = rdinitdebug ] dracut: + return 0 dracut: + set +x dracut:/# ++++++++++
On 06/03/2010 03:04 PM, Lamar Owen wrote:
qpti f00fccd4: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2
I think this file is in the linux-firmware package, which may not have been installed. You might need to boot into rescue mode, install that package, and regenerate the initrd.
Then again, the qlogicpti driver failing to load may have nothing to do with your failure. I don't know what's hanging off that SCSI bus.
~spot
On Thursday, June 03, 2010 04:14:37 pm Tom "spot" Callaway wrote:
On 06/03/2010 03:04 PM, Lamar Owen wrote:
qpti f00fccd4: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2
I think this file is in the linux-firmware package, which may not have been installed. You might need to boot into rescue mode, install that package, and regenerate the initrd.
It's installed; and I can successfully load it inside dracut's rdshell: ++++++++++ dracut:/# modprobe qlogicpti qlogicpti0: IRQ 19 SCSI ID 7 qpti f00fccd4: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.28 99/11/08) qlogicpti0: [Ultra Wide, using differential interface] scsi3 : PTI Qlogic,ISP SBUS SCSI irq 19 regs at 000001c700010000 qlogicpti1: IRQ 45 SCSI ID 7 qpti f02b6520: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.25 96/10/15) qlogicpti1: [Ultra Wide, using differential interface] scsi4 : PTI Qlogic,ISP SBUS SCSI irq 45 regs at 000001d520010000 qlogicpti2: IRQ 54 SCSI ID 7 qpti f02c9e60: firmware: requesting qlogic/isp1000.bin scsi 3:0:0:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 (Firmware v1.31.32)(FCode 1.28 99/11/08) qlogicpti2: [Ultra Wide, using differential interface] scsi5 : PTI Qlogic,ISP SBUS SCSI irq 54 regs at 000001d700010000 drascsi 3:0:1:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 cut:/scsi 3:0:2:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 # scsi 3:0:3:0: Direct-Access COMPAQ BD036659CC 3B00 PQ: 0 ANSI: 3 scsi 5:0:8:0: Direct-Access SEAGATE ST336607LC 0007 PQ: 0 ANSI: 3 scsi 5:0:9:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 5:0:10:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 scsi 5:0:12:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 3:0:14:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 3:0:0:0: Attached scsi generic sg1 type 0 scsi 5:0:15:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 3:0:1:0: Attached scsi generic sg2 type 0 sd 3:0:2:0: Attached scsi generic sg3 type 0 sd 3:0:3:0: Attached scsi generic sg4 type 0 scsi 3:0:14:0: Attached scsi generic sg5 type 3 sd 3:0:0:0: [sda] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 5:0:8:0: Attached scsi generic sg6 type 0 sd 5:0:9:0: Attached scsi generic sg7 type 0 sd 5:0:10:0: Attached scsi generic sg8 type 0 sd 5:0:12:0: Attached scsi generic sg9 type 0 scsi 5:0:15:0: Attached scsi generic sg10 type 3 sd 3:0:1:0: [sdb] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 3:0:3:0: [sdd] 71132000 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 3:0:1:0: [sdb] Write Protect is off sd 3:0:2:0: [sdc] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 3:0:2:0: [sdc] Write Protect is off sd 3:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 5:0:10:0: [sdg] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 5:0:8:0: [sde] 71687372 512-byte logical blocks: (36.7 GB/34.1 GiB) sd 3:0:3:0: [sdd] Write Protect is off sd 5:0:9:0: [sdf] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 3:0:2:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 5:0:8:0: [sde] Write Protect is off sd 5:0:10:0: [sdg] Write Protect is off sd 5:0:12:0: [sdh] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 5:0:12:0: [sdh] Write Protect is off sd 3:0:3:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 5:0:9:0: [sdf] Write Protect is off sd 5:0:8:0: [sde] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 5:0:10:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA sdb: sdb3 sd 5:0:12:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 5:0:9:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 3:0:0:0: [sda] Write Protect is off sdc: sdc3 sd 3:0:1:0: [sdb] Attached SCSI disk sdh: sdh3 sde: sd 3:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA sdg: sdf: sdd: sdg3 sd 3:0:2:0: [sdc] Attached SCSI disk sd 5:0:12:0: [sdh] Attached SCSI disk sdf3 sde3 sdd3 sda: sd 5:0:8:0: [sde] Attached SCSI disk sd 5:0:10:0: [sdg] Attached SCSI disk sda1 sda2 sda3 sd 5:0:9:0: [sdf] Attached SCSI disk sd 3:0:3:0: [sdd] Attached SCSI disk sd 3:0:0:0: [sda] Attached SCSI disk device-mapper: multipath: version 1.1.0 loaded +++++++++++++
But if I pass rdloaddriver=qlogicpti on the boot command line to dracut, I get: +++++++++++++ dracut: + modprobe qlogicpti qlogicpti0: IRQ 19 SCSI ID 7 qpti f00fccd4: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2 qlogicpti0: IRQ 45 SCSI ID 7 qpti f02b6520: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2 qlogicpti0: IRQ 54 SCSI ID 7 qpti f02c9e60: firmware: requesting qlogic/isp1000.bin Failed to load image "qlogic/isp1000.bin" err -2 +++++++++++++
which implies to me that at the time dracut is executing rdloaddriver=qlogicpti, dracut is unaware that the firmware is in /lib/firmware/, but by the time dracut passes control to the console through rdshell it is aware of that path.
Then again, the qlogicpti driver failing to load may have nothing to do with your failure. I don't know what's hanging off that SCSI bus.
The /boot and / filesystems:
(To simplify things, I reconfigured the IO boards, reducing from four to one, which makes the dmesg segment below differ some from the previous ones, and this output was produced from booting the DVD in rescue mode, which I have down to a science, now, knowing I need to load three drivers, all located on past the 25th page of the driver list.....and it's a fantastic thing to be able to do all that remotely, including soft resetting of the system with the Sun remote console feature (Ctrl-M Ctrl-M ~ Ctrl-Shift-r typed slowly, with about a second of pause between characters)
+++++ sh-4.0# chroot /mnt/sysimage sh-4.0# lvscan ACTIVE '/dev/vg_spacely/lv_root' [16.86 GB] inherit ACTIVE '/dev/vg_spacely/lv_swap' [16.86 GB] inherit sh-4.0# pvscan PV /dev/sde2 VG vg_spacely lvm2 [33.72 GB / 0 free] Total: 2 [67.78 GB] / in use: 2 [67.78 GB] / in no VG: 0 [0 ] sh-4.0# dmesg [SNIP] qlogicpti0: IRQ 12 SCSI ID 7 qpti f00f6520: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.25 96/10/15) qlogicpti0: [Ultra Wide, using differential interface] scsi0 : PTI Qlogic,ISP SBUS SCSI irq 12 regs at 000001c520010000 qlogicpti1: IRQ 21 SCSI ID 7 qpti f0109e60: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.28 99/11/08) qlogicpti1: [Ultra Wide, using differential interface] scsi1 : PTI Qlogic,ISP SBUS SCSI irq 21 regs at 000001c700010000 scsi 0:0:8:0: Direct-Access SEAGATE ST336607LC 0007 PQ: 0 ANSI: 3 scsi 0:0:9:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 0:0:10:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 scsi 1:0:0:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 0:0:12:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 1:0:1:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 1:0:2:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 scsi 1:0:3:0: Direct-Access COMPAQ BD036659CC 3B00 PQ: 0 ANSI: 3 scsi 0:0:15:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 0:0:8:0: Attached scsi generic sg0 type 0 sd 0:0:9:0: Attached scsi generic sg1 type 0 sd 0:0:10:0: Attached scsi generic sg2 type 0 sd 0:0:12:0: Attached scsi generic sg3 type 0 scsi 0:0:15:0: Attached scsi generic sg4 type 3 sd 0:0:9:0: [sdb] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 0:0:12:0: [sdd] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 0:0:8:0: [sda] 71687372 512-byte logical blocks: (36.7 GB/34.1 GiB) sd 0:0:10:0: [sdc] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 0:0:9:0: [sdb] Write Protect is off sd 0:0:9:0: [sdb] Mode Sense: ab 00 10 08 sd 0:0:12:0: [sdd] Write Protect is off sd 0:0:12:0: [sdd] Mode Sense: ab 00 10 08 sd 0:0:8:0: [sda] Write Protect is off sd 0:0:8:0: [sda] Mode Sense: ab 00 10 08 sd 0:0:10:0: [sdc] Write Protect is off sd 0:0:10:0: [sdc] Mode Sense: d3 00 10 08 sd 0:0:9:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 0:0:8:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 0:0:12:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 0:0:10:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA sdb: sda: sdd: sdc: sdd3 sda3 sdb3 sdc3 sd 0:0:8:0: [sda] Attached SCSI disk sd 0:0:12:0: [sdd] Attached SCSI disk sd 0:0:9:0: [sdb] Attached SCSI disk sd 0:0:10:0: [sdc] Attached SCSI disk scsi 1:0:14:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 1:0:0:0: Attached scsi generic sg5 type 0 sd 1:0:1:0: Attached scsi generic sg6 type 0 sd 1:0:2:0: Attached scsi generic sg7 type 0 sd 1:0:3:0: Attached scsi generic sg8 type 0 scsi 1:0:14:0: Attached scsi generic sg9 type 3 sd 1:0:1:0: [sdf] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 1:0:0:0: [sde] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 1:0:3:0: [sdh] 71132000 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 1:0:2:0: [sdg] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 1:0:0:0: [sde] Write Protect is off sd 1:0:0:0: [sde] Mode Sense: ab 00 10 08 sd 1:0:1:0: [sdf] Write Protect is off sd 1:0:1:0: [sdf] Mode Sense: ab 00 10 08 sd 1:0:2:0: [sdg] Write Protect is off sd 1:0:2:0: [sdg] Mode Sense: d3 00 10 08 sd 1:0:1:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 1:0:0:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 1:0:3:0: [sdh] Write Protect is off sd 1:0:3:0: [sdh] Mode Sense: 13 00 10 08 sd 1:0:2:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 1:0:3:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA sdf: sde: sdg: sdh: sdf3 sdg3 sde1 sde2 sde3 sdh3 sd 1:0:1:0: [sdf] Attached SCSI disk sd 1:0:2:0: [sdg] Attached SCSI disk sd 1:0:0:0: [sde] Attached SCSI disk sd 1:0:3:0: [sdh] Attached SCSI disk [SNIP] sh-4.0# mount /dev/mapper/vg_spacely-lv_root on / type ext4 (rw) /dev/sde1 on /boot type ext3 (rw) devpts on /dev/pts type devpts (rw) tmpfs on /dev/shm type tmpfs (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) sh-4.0# ++++++++++++ In other words, no qlogicpti, no access to the root filesystem, and the boot fails (just like it tells me).
So, to me, the core issues are: 1.) Why isn't qlogicpti (and, apparently, sunhme and sun_esp) not getting automatically loaded by dracut? 2.) Why is dracut not finding /lib/firmware/qlogic/isp1000.bin when trying rdloaddriver=qlogicpti, which tries to load qlogic/isp1000.bin, but finds it (by the same name, qlogic/isp1000.bin) just fine when modprobe qlogicpti is typed in at the same dracut's rdshell command line?
On Thursday, June 03, 2010 05:07:12 pm Lamar Owen wrote:
So, to me, the core issues are: 1.) Why isn't qlogicpti (and, apparently, sunhme and sun_esp) not getting automatically loaded by dracut?
I suspect that udev does not support sbus properly and is failing to load the module, i also suspect that the same is the reason that things are failing in anaconda also.
2.) Why is dracut not finding /lib/firmware/qlogic/isp1000.bin when trying rdloaddriver=qlogicpti, which tries to load qlogic/isp1000.bin, but finds it (by the same name, qlogic/isp1000.bin) just fine when modprobe qlogicpti is typed in at the same dracut's rdshell command line?
this i'm not sure of. we should try and debug it
Dennis
On Thursday, June 03, 2010 06:29:12 pm Dennis Gilmore wrote:
On Thursday, June 03, 2010 05:07:12 pm Lamar Owen wrote:
So, to me, the core issues are: 1.) Why isn't qlogicpti (and, apparently, sunhme and sun_esp) not getting automatically loaded by dracut?
I suspect that udev does not support sbus properly and is failing to load the module, i also suspect that the same is the reason that things are failing in anaconda also.
Sounds reasonable; you should be able to reproduce easily with the E3000.
2.) Why is dracut not finding /lib/firmware/qlogic/isp1000.bin when trying rdloaddriver=qlogicpti, which tries to load qlogic/isp1000.bin, but finds it (by the same name, qlogic/isp1000.bin) just fine when modprobe qlogicpti is typed in at the same dracut's rdshell command line?
this i'm not sure of. we should try and debug it
What do you need from me to help with that? I can send you an IO board with one or more QLogic ISP1000's on it, or just the ISP1000, if you have a D1000 shelf (or equivalent HVD SCSI enclosure) to run it. Or I can send you info from this E6500; after all, every boot of the box goes through an rdshell session at this point.
I have a few other SBUS cards if you want to try them; an SBUS gigabit ethernet, a number of SBUS JNI FC64 fibre-channel cards (not likely to work at all, though), among others.....
And, well, after adding an /etc/event.d/ttyS0 file with the right contents, I now have a getty on the console. Now to get networking.....got it, just needed to do the following: [root@spacely ~]# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
[root@spacely ~]# modprobe sunhme [root@spacely ~]# ifup eth0 [root@spacely ~]# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:20:XX:CA:05 inet addr:XX.YY.ZZ.AA Bcast:XX.YY.ZZ.255 Mask:255.255.255.0 inet6 addr: fe80::a00:20ff:febd:ca05/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:31 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:218 (218.0 b) TX bytes:4666 (4.5 KiB) Interrupt:19
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:100 (100.0 b) TX bytes:100 (100.0 b)
[root@spacely ~]# So now I can ssh in with -Y and get gui stuff.. Console log of the successful boot, which also shows the manual intervention at the rdshell dracut prompt: ++++++++++ Resetting... Software Power ON screen not found. Can't open input device. Keyboard not present. Using ttya for input and output.
16-slot Sun Enterprise E6500, No Keyboard OpenBoot 3.2.30, 20480 MB memory installed, Serial #12438021. Copyright 2002 Sun Microsystems, Inc. All rights reserved Ethernet address 8:0:20:bd:ca:5, Host ID: 80bdca05.
Rebooting with command: boot Boot device: /sbus@3,0/QLGC,isp@0,10000/sd@0,0:a File and args: SILO Version 1.4.14 \ Welcome to Fedora! Hit <TAB> for boot options
boot: Allocated 64 Megs of memory at 0x40000000 for kernel Loaded kernel version 2.6.32 Loading initial ramdisk (13032899 bytes at 0x4400000 phys, 0x40C00000 virt)... - PROMLIB: Sun IEEE Boot Prom 'OBP 3.2.30 2002/10/25 14:03' PROMLIB: Root node compatible: Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 2.6.32.10-90.fc12.sparc64 (mockbuild@korolev.ausil.us) (gcc version 4.4.3 20100409 (Red Hat 4.4.3-17) (GCC) ) #1 SMP Thu Apr 15 13:30:40 CDT 2010 bootconsole [earlyprom0] enabled ARCH: SUN4U Ethernet address: 08:00:20:bd:ca:05 Kernel: Using 3 locked TLB entries for main kernel image. Remapping the kernel... done. OF stdout device is: /central@1f,0/fhc@0,f8800000/zs@0,902000:a PROM: Built device tree with 119877 bytes of memory. Top of RAM: 0x4ffd14000, Total RAM: 0x4ff412000 Memory hole size: 9MB [0000010000000000-fffff80001000000] page_structs=131072 node=0 entry=0/0 [0000010000000000-fffff80001400000] page_structs=131072 node=0 entry=1/0 [0000010000800000-fffff80001800000] page_structs=131072 node=0 entry=2/0 [0000010000800000-fffff80001c00000] page_structs=131072 node=0 entry=3/0 [0000010001000000-fffff80002000000] page_structs=131072 node=0 entry=4/0 [0000010001000000-fffff80002400000] page_structs=131072 node=0 entry=5/0 [0000010001800000-fffff80002800000] page_structs=131072 node=0 entry=6/0 [0000010001800000-fffff80002c00000] page_structs=131072 node=0 entry=7/0 [0000010002000000-fffff80003000000] page_structs=131072 node=0 entry=8/0 [0000010002000000-fffff80003400000] page_structs=131072 node=0 entry=9/0 [0000010002800000-fffff80003800000] page_structs=131072 node=0 entry=10/0 [0000010002800000-fffff80003c00000] page_structs=131072 node=0 entry=11/0 [0000010003000000-fffff80004000000] page_structs=131072 node=0 entry=12/0 [0000010003000000-fffff80005400000] page_structs=131072 node=0 entry=13/0 [0000010003800000-fffff80005800000] page_structs=131072 node=0 entry=14/0 [0000010003800000-fffff80005c00000] page_structs=131072 node=0 entry=15/0 [0000010004000000-fffff80006000000] page_structs=131072 node=0 entry=16/0 [0000010004000000-fffff80006400000] page_structs=131072 node=0 entry=17/0 [0000010004800000-fffff80006800000] page_structs=131072 node=0 entry=18/0 [0000010004800000-fffff80006c00000] page_structs=131072 node=0 entry=19/0 [0000010005000000-fffff80007000000] page_structs=131072 node=0 entry=20/0 [0000010005000000-fffff80007400000] page_structs=131072 node=0 entry=21/0 [0000010005800000-fffff80007800000] page_structs=131072 node=0 entry=22/0 [0000010005800000-fffff80007c00000] page_structs=131072 node=0 entry=23/0 [0000010006000000-fffff80008000000] page_structs=131072 node=0 entry=24/0 [0000010006000000-fffff80008400000] page_structs=131072 node=0 entry=25/0 [0000010006800000-fffff80008800000] page_structs=131072 node=0 entry=26/0 [0000010006800000-fffff80008c00000] page_structs=131072 node=0 entry=27/0 [0000010007000000-fffff80009000000] page_structs=131072 node=0 entry=28/0 [0000010007000000-fffff80009400000] page_structs=131072 node=0 entry=29/0 [0000010007800000-fffff80009800000] page_structs=131072 node=0 entry=30/0 [0000010007800000-fffff80009c00000] page_structs=131072 node=0 entry=31/0 [0000010008000000-fffff8000a000000] page_structs=131072 node=0 entry=32/0 [0000010008000000-fffff8000a400000] page_structs=131072 node=0 entry=33/0 [0000010008800000-fffff8000a800000] page_structs=131072 node=0 entry=34/0 [0000010008800000-fffff8000ac00000] page_structs=131072 node=0 entry=35/0 [0000010009000000-fffff8000b000000] page_structs=131072 node=0 entry=36/0 [0000010009000000-fffff8000b400000] page_structs=131072 node=0 entry=37/0 [0000010009800000-fffff8000b800000] page_structs=131072 node=0 entry=38/0 [0000010009800000-fffff8000bc00000] page_structs=131072 node=0 entry=39/0 Zone PFN ranges: Normal 0x00000000 -> 0x0027fe8a Movable zone start PFN for each node early_node_map[3] active PFN ranges 0: 0x00000000 -> 0x0027f987 0: 0x0027fe00 -> 0x0027fe75 0: 0x0027fe7d -> 0x0027fe8a Booting Linux... PERCPU: Embedded 7 pages/cpu @fffff8000c000000 s27136 r8192 d22016 u1048576 pcpu-alloc: s27136 r8192 d22016 u1048576 alloc=1*4194304 pcpu-alloc: [0] 00 01 04 05 [0] 08 09 12 13 pcpu-alloc: [0] 16 17 20 21 [0] 24 25 26 27 pcpu-alloc: [0] 28 -- -- -- Built 1 zonelists in Node order, mobility grouping on. Total pages: 2599435 Policy zone: Normal Kernel command line: root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp PID hash table entries: 4096 (order: 2, 32768 bytes) Memory: 20772328k available (4536k kernel code, 2176k data, 400k init) [fffff80000000000,00000004ffd14000] SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=29, Nodes=16 Hierarchical RCU implementation. NR_IRQS:255 clocksource: mult[28000] shift[16] clockevent: mult[66666666] shift[32] Console: colour dummy device 80x25 allocated 104857600 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Calibrating delay using timer specific routine.. 801.50 BogoMIPS (lpj=4007522) Security Framework initialized SELinux: Initializing. Dentry cache hash table entries: 4194304 (order: 12, 33554432 bytes) Inode-cache hash table entries: 2097152 (order: 11, 16777216 bytes) Mount-cache hash table entries: 512 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys net_cls ftrace: allocating 17120 entries in 34 pages CPU 1: synchronized TICK with master CPU (last diff -1 cycles, maxerr 813 cycles) CPU 4: synchronized TICK with master CPU (last diff 22 cycles, maxerr 813 cycles) CPU 5: synchronized TICK with master CPU (last diff 8 cycles, maxerr 841 cycles) CPU 8: synchronized TICK with master CPU (last diff -10 cycles, maxerr 870 cycles) CPU 9: synchronized TICK with master CPU (last diff -20 cycles, maxerr 870 cycles) CPU 12: synchronized TICK with master CPU (last diff 2 cycles, maxerr 850 cycles) CPU 13: synchronized TICK with master CPU (last diff 11 cycles, maxerr 819 cycles) CPU 16: synchronized TICK with master CPU (last diff -10 cycles, maxerr 860 cycles) CPU 17: synchronized TICK with master CPU (last diff -8 cycles, maxerr 870 cycles) CPU 20: synchronized TICK with master CPU (last diff -5 cycles, maxerr 868 cycles) CPU 21: synchronized TICK with master CPU (last diff 5 cycles, maxerr 818 cycles) CPU 24: synchronized TICK with master CPU (last diff -20 cycles, maxerr 843 cycles) CPU 25: synchronized TICK with master CPU (last diff -20 cycles, maxerr 822 cycles) CPU 26: synchronized TICK with master CPU (last diff -25 cycles, maxerr 868 cycles) CPU 27: synchronized TICK with master CPU (last diff -15 cycles, maxerr 870 cycles) CPU 28: synchronized TICK with master CPU (last diff -24 cycles, maxerr 880 cycles) Brought up 17 CPUs devtmpfs: initialized regulator: core version 0.5 NET: Registered protocol family 16 fhc: Board #1, Version[1] PartID[fa0] Manuf[3e] (Central) fhc: Board #0, Version[1] PartID[fa0] Manuf[3e] (JTAG Master) fhc: Board #2, Version[1] PartID[fa0] Manuf[3e] fhc: Board #4, Version[1] PartID[fa0] Manuf[3e] fhc: Board #6, Version[1] PartID[fa0] Manuf[3e] fhc: Board #8, Version[1] PartID[fa0] Manuf[3e] fhc: Board #10, Version[1] PartID[fa0] Manuf[3e] fhc: Board #12, Version[1] PartID[fa0] Manuf[3e] fhc: Board #13, Version[1] PartID[fa0] Manuf[3e] fhc: Board #14, Version[1] PartID[fa0] Manuf[3e] fhc: Board #1, Version[1] PartID[fa0] Manuf[3e] clock_board: Detected 16 slot Enterprise system. SYSIO: UPA portID ffffffff, at 000001c400000000 SYSIO: UPA portID ffffffff, at 000001c600000000 bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default /central/fhc@0,f8800000/eeprom@0,908000: Mostek regs at 0x1fff8908000 Switching to clocksource tick NET: Registered protocol family 2 IP route cache hash table entries: 524288 (order: 9, 4194304 bytes) TCP established hash table entries: 524288 (order: 10, 8388608 bytes) TCP bind hash table entries: 65536 (order: 7, 1048576 bytes) TCP: Hash tables configured (established 524288 bind 65536) TCP reno registered NET: Registered protocol family 1 Trying to unpack rootfs image as initramfs... Freeing initrd memory: 12727k freed audit: initializing netlink socket (disabled) type=2000 audit(6.574:1): initialized HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 8192 bytes) msgmni has been set to 32768 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci-stub: invalid id string "" f005de3c: ttyS0 at MMIO 0x1fff8902000 (irq = 2) is a zs (ESCC) Console: ttyS0 (SunZilog zs0) console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled f005de3c: ttyS1 at MMIO 0x1fff8902004 (irq = 2) is a zs (ESCC) f005df14: Keyboard at MMIO 0x1fff8904000 (irq = 2) is a zs f005df14: Mouse at MMIO 0x1fff8904004 (irq = 2) is a zs brd: module loaded loop: module loaded Fixed MDIO Bus: probed ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver mice: PS/2 mouse device common for all mice rtc-m48t59 rtc-m48t59.0: rtc core: registered m48t59 as rtc0 device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 registered taskstats version 1 rtc-m48t59 rtc-m48t59.0: setting system clock to 2010-06-03 22:42:28 UTC (1275604948) Initalizing network drop monitor service esp: esp0, regs[1c738810000:1c738800000] irq[20] esp: esp0 is a FASHME, 40 MHz (ccf=0), SCSI ID 7 scsi0 : esp dracut: dracut-004-4.fc12 udev: starting version 145 dracut: Starting plymouth daemon scsi: waiting for bus probes to complete ... scsi 0:0:6:0: CD-ROM TOSHIBA DVD-ROM SD-M1401 1009 PQ: 0 ANSI: 2 scsi target0:0:6: Beginning Domain Validation scsi target0:0:6: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) scsi target0:0:6: Domain Validation skipping write tests scsi target0:0:6: Ending Domain Validation scsi 0:0:10:0: Direct-Access IBM DDYS-T36950M S80D PQ: 0 ANSI: 3 scsi target0:0:10: Beginning Domain Validation scsi target0:0:10: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 15) scsi target0:0:10: Domain Validation skipping write tests scsi target0:0:10: Ending Domain Validation scsi 0:0:11:0: Direct-Access SEAGATE ST318453LC DX10 PQ: 0 ANSI: 3 scsi target0:0:11: Beginning Domain Validation scsi target0:0:11: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 15) scsi target0:0:11: Domain Validation skipping write tests scsi target0:0:11: Ending Domain Validation sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 0:0:6:0: Attached scsi generic sg0 type 5 sd 0:0:10:0: Attached scsi generic sg1 type 0 sd 0:0:11:0: Attached scsi generic sg2 type 0 sd 0:0:10:0: [sda] 71687340 512-byte logical blocks: (36.7 GB/34.1 GiB) sd 0:0:10:0: [sda] Write Protect is off sd 0:0:10:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:11:0: [sdb] 35566478 512-byte logical blocks: (18.2 GB/16.9 GiB) sd 0:0:11:0: [sdb] Write Protect is off sda: sd 0:0:11:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA sda1 sda2 sda3 sdb: sd 0:0:10:0: [sda] Attached SCSI disk sdb1 sdb3 sd 0:0:11:0: [sdb] Attached SCSI disk device-mapper: multipath: version 1.1.0 loaded dracut: Scanning devices sda2 for LVM volume groups dracut: Reading all physical volumes. This may take a while... dracut: Found volume group "VolGroup00" using metadata type lvm2 dracut: 2 logical volume(s) in volume group "VolGroup00" now active + echo
+ echo
+ echo No root device found No root device found + source_all emergency + local f + [ emergency ] + [ -d /emergency ] + [ -e /emergency/50plymouth-emergency.sh ] + . /emergency/50plymouth-emergency.sh + [ -x /bin/plymouth ] + /bin/plymouth --hide-splash + echo
+ echo
+ echo No root device found No root device found + source_all emergency + local f + [ emergency ] + [ -d /emergency ] + [ -e /emergency/50plymouth-emergency.sh ] + . /emergency/50plymouth-emergency.sh + [ -x /bin/plymouth ] + /bin/plymouth --hide-splash + echo
+ getarg rdshell + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = rdshell ] + [ root = rdshell ] + [ ro = rdshell ] + [ ro = rdshell ] + [ LANG=en_US.UTF-8 = rdshell ] + [ LANG = rdshell ] + [ SYSFONT=latarcyrheb-sun16 = rdshell ] + [ SYSFONT = rdshell ] + [ KEYTABLE=us = rdshell ] + [ KEYTABLE = rdshell ] + [ console=ttyS0,9600 = rdshell ] + [ console = rdshell ] + [ rdinitdebug = rdshell ] + [ rdinitdebug = rdshell ] + [ rdshell = rdshell ] + return 0 + echo Dropping to debug shell. Dropping to debug shell. + echo
+ export PS1=dracut:${PWD}# + [ -e /.profile ] + echo exec 0<>/dev/console 1<>/dev/console 2<>/dev/console + sh -i -l sh: can't access tty; job control turned off dracut:/# modprobe qlogicpti qlogicpti0: IRQ 12 SCSI ID 7 qpti f00f6520: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.25 96/10/15) qlogicpti0: [Ultra Wide, using differential interface] scsi1 : PTI Qlogic,ISP SBUS SCSI irq 12 regs at 000001c520010000 qlogicpti1: IRQ 21 SCSI ID 7 qpti f0109e60: firmware: requesting qlogic/isp1000.bin (Firmware v1.31.32)(FCode 1.28 99/11/08) qlogicpti1: [Ultra Wide, using differential interface] scsi2 : PTI Qlogic,ISP SBUS SCSI irq 21 regs at 000001c700010000 dracut:/# scsi 1:0:8:0: Direct-Access SEAGATE ST336607LC 0007 PQ: 0 ANSI: 3 scsi 1:0:9:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 2:0:0:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 2:0:1:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 1:0:10:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 scsi 2:0:2:0: Direct-Access SEAGATE ST336605LSUN36G 0238 PQ: 0 ANSI: 3 scsi 2:0:3:0: Direct-Access COMPAQ BD036659CC 3B00 PQ: 0 ANSI: 3 scsi 1:0:12:0: Direct-Access SEAGATE ST336607LC DS09 PQ: 0 ANSI: 3 scsi 1:0:15:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 1:0:8:0: Attached scsi generic sg3 type 0 sd 1:0:9:0: Attached scsi generic sg4 type 0 sd 1:0:8:0: [sdc] 71687372 512-byte logical blocks: (36.7 GB/34.1 GiB) sd 1:0:10:0: Attached scsi generic sg5 type 0 sd 1:0:12:0: Attached scsi generic sg6 type 0 scsi 1:0:15:0: Attached scsi generic sg7 type 3 sd 1:0:8:0: [sdc] Write Protect is off sd 1:0:9:0: [sdd] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 1:0:10:0: [sde] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 1:0:12:0: [sdf] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 1:0:8:0: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 1:0:12:0: [sdf] Write Protect is off sd 1:0:9:0: [sdd] Write Protect is off sd 1:0:12:0: [sdf] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 1:0:9:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA sdc: sdc3 sdd: sd 1:0:10:0: [sde] Write Protect is off sd 1:0:10:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 1:0:8:0: [sdc] Attached SCSI disk sdf: sde: sdd3 sdf3 sde3 sd 1:0:9:0: [sdd] Attached SCSI disk sd 1:0:12:0: [sdf] Attached SCSI disk sd 1:0:10:0: [sde] Attached SCSI disk scsi 2:0:14:0: Processor SYMBIOS D1000 2 PQ: 0 ANSI: 2 sd 2:0:0:0: Attached scsi generic sg8 type 0 sd 2:0:0:0: [sdg] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 2:0:1:0: Attached scsi generic sg9 type 0 sd 2:0:1:0: [sdh] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 2:0:2:0: Attached scsi generic sg10 type 0 sd 2:0:0:0: [sdg] Write Protect is off sd 2:0:2:0: [sdi] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB) sd 2:0:3:0: Attached scsi generic sg11 type 0 sd 2:0:2:0: [sdi] Write Protect is off sd 2:0:0:0: [sdg] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 2:0:3:0: [sdj] 71132000 512-byte logical blocks: (36.4 GB/33.9 GiB) scsi 2:0:14:0: Attached scsi generic sg12 type 3 sd 2:0:2:0: [sdi] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 2:0:3:0: [sdj] Write Protect is off sdg: sdg1 sdg2 sdg3 sd 2:0:3:0: [sdj] Write cache: disabled, read cache: enabled, supports DPO and FUA sdi: sd 2:0:1:0: [sdh] Write Protect is off sd 2:0:1:0: [sdh] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 2:0:0:0: [sdg] Attached SCSI disk sdj: sdi3 sdh: sdj3 sdh3 sd 2:0:2:0: [sdi] Attached SCSI disk sd 2:0:3:0: [sdj] Attached SCSI disk sd 2:0:1:0: [sdh] Attached SCSI disk lvm vgscan File descriptor 9 (/.console_lock) leaked on lvm invocation. Parent PID 1050: sh Reading all physical volumes. This may take a while... Found volume group "vg_spacely" using metadata type lvm2 Found volume group "VolGroup00" using metadata type lvm2 dracut:/# lvm vgchange -ay File descriptor 9 (/.console_lock) leaked on lvm invocation. Parent PID 1050: sh 2 logical volume(s) in volume group "vg_spacely" now active 2 logical volume(s) in volume group "VolGroup00" now active dracut:/# ln -s /dev/mapper/vg_spacely-lv_root /dev/root dracut:/# exit + : + check_finished + local f + [ -e /initqueue-finished/block.sh ] + . /initqueue-finished/block.sh +EXT4-fs (dm-2): mounted filesystem with ordered data mode [ -e /dev/root ] + return 0 + break + unset job + unset queuetriggdracut: Mounted root filesystem /dev/mapper/vg_spacely-lv_root ered + getarg rdbreak=pre-mount + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = rdbreak=pre-mount ] + [ root = rdbreak=pre-mount ] + [ ro = rdbreak=pre-mount ] + [ ro = rdbreak=pre-mount ] + [ LANG=en_US.UTF-8 = rdbreak=pre-mount ] + [ LANG = rdbreak=pre-mount ] + [ SYSFONT=latarcyrheb-sun16 = rdbreak=pre-mount ] + [ SYSFONT = rdbreak=pre-mount ] + [ KEYTABLE=us = rdbreak=pre-mount ] + [ KEYTABLE = rdbreak=pre-mount ] + [ console=ttyS0,9600 = rdbreak=pre-mount ] + [ console = rdbreak=pre-mount ] + [ rdinitdebug = rdbreak=pre-mount ] + [ rdinitdebug = rdbreak=pre-mount ] + [ rdshell = rdbreak=pre-mount ] + [ rdshell = rdbreak=pre-mount ] + [ rdloaddriver=sun_esp = rdbreak=pre-mount ] + [ rdloaddriver = rdbreak=pre-mount ] + return 1 + source_all pre-mount + local f + [ pre-mount ] + [ -d /pre-mount ] + return + getarg rdbreak=mount + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = rdbreak=mount ] + [ root = rdbreak=mount ] + [ ro = rdbreak=mount ] + [ ro = rdbreak=mount ] + [ LANG=en_US.UTF-8 = rdbreak=mount ] + [ LANG = rdbreak=mount ] + [ SYSFONT=latarcyrheb-sun16 = rdbreak=mount ] + [ SYSFONT = rdbreak=mount ] + [ KEYTABLE=us = rdbreak=mount ] + [ KEYTABLE = rdbreak=mount ] + [ console=ttyS0,9600 = rdbreak=mount ] + [ console = rdbreak=mount ] + [ rdinitdebug = rdbreak=mount ] + [ rdinitdebug = rdbreak=mount ] + [ rdshell = rdbreak=mount ] + [ rdshell = rdbreak=mount ] + [ rdloaddriver=sun_esp = rdbreak=mount ] + [ rdloaddriver = rdbreak=mount ] + return 1 + i=0 + : + [ -d /sysroot/proc ] + [ -f /mount/10resume.sh ] + . /mount/10resume.sh + [ -s /.resume -a -b ] + [ -d /sysroot/proc ] + [ -f /mount/99mount-root.sh ] + . /mount/99mount-root.sh + . /lib/dracut-lib.sh + [ -n block:/dev/mapper/vg_spacely-lv_root -a -z ] + mount -t auto -o ro /dev/mapper/vg_spacely-lv_root /sysroot + ROOTFS_MOUNTED=yes + getarg rd_NO_FSTAB + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = rd_NO_FSTAB ] + [ root = rd_NO_FSTAB ] + [ ro = rd_NO_FSTAB ] + [ ro = rd_NO_FSTAB ] + [ LANG=en_US.UTF-8 = rd_NO_FSTAB ] + [ LANG = rd_NO_FSTAB ] + [ SYSFONT=latarcyrheb-sun16 = rd_NO_FSTAB ] + [ SYSFONT = rd_NO_FSTAB ] + [ KEYTABLE=us = rd_NO_FSTAB ] + [ KEYTABLE = rd_NO_FSTAB ] + [ console=ttyS0,9600 = rd_NO_FSTAB ] + [ console = rd_NO_FSTAB ] + [ rdinitdebug = rd_NO_FSTAB ] + [ rdinitdebug = rd_NO_FSTAB ] + [ rdshell = rd_NO_FSTAB ] + [ rdshell = rd_NO_FSTAB ] + [ rdloaddriver=sun_esp = rd_NO_FSTAB ] + [ rdloaddriver = rd_NO_FSTAB ] + return 1 + getarg rootflags + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = rootflags ] + [ root = rootflags ] + [ ro = rootflags ] + [ ro = rootflags ] + [ LANG=en_US.UTF-8 = rootflags ] + [ LANG = rootflags ] + [ SYSFONT=latarcyrheb-sun16 = rootflags ] + [ SYSFONT = rootflags ] + [ KEYTABLE=us = rootflags ] + [ KEYTABLE = rootflags ] + [ console=ttyS0,9600 = rootflags ] + [ console = rootflags ] + [ rdinitdebug = rootflags ] + [ rdinitdebug = rootflags ] + [ rdshell = rootflags ] + [ rdshell = rootflags ] + [ rdloaddriver=sun_esp = rootflags ] + [ rdloaddriver = rootflags ] + return 1 + [ -f /sysroot/etc/fstab ] + [ -L /sysroot/etc/fstab ] + rootfs=auto + rootopts=defaults + read dev mp fs opts rest + [ = / ] + read dev mp fs opts rest + [ = / ] + read dev mp fs opts rest + [ /etc/fstab = / ] + read dev mp fs opts rest + [ Created = / ] + read dev mp fs opts rest + [ = / ] + read dev mp fs opts rest + [ Accessible = / ] + read dev mp fs opts rest + [ See = / ] + read dev mp fs opts rest + [ = / ] + read dev mp fs opts rest + [ / = / ] + rootfs=ext4 + rootopts=defaults + break + [ defaults != defaults ] + [ -d /sysroot/proc ] + break + i=1 + [ 1 -gt 20 ] + : + [ -d /sysroot/proc ] + break + echo -n Mounted root filesystem + read dev mp rest + [+ / = /sysroot ]vinfo
+ + readread dev line mp rest + [ /proc = /sysroot ] + read dev mp rest + [ /sys = /sysroot ] + read dev mp rest + [ /dev = /sysroot ] + read dev mp rest + [ /dev/pts = /sysroot ] + read dev mp rest + [ /dev/shm = /sysroot ] + read dev mp rest + [ /sysroot = /sysroot ] + echo /dev/mapper/vg_spacely-lv_root + read dev mp rest + info Mounted root filesystem /dev/mapper/vg_spacely-lv_root + check_quiet + [ -z yes ] + echo <6>dracut: Mounted root filesystem /dev/mapper/vg_spacely-lv_root + [ yes != yes ] + read line + getarg rdbreak=pre-pivot + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = rdbreak=pre-pivot ] + [ root = rdbreak=pre-pivot ] + [ ro = rdbreak=pre-pivot ] + [ ro = rdbreak=pre-pivot ] + [ LANG=en_US.UTF-8 = rdbreak=pre-pivot ] + [ LANG = rdbreak=pre-pivot ] + [ SYSFONT=latarcyrheb-sun16 = rdbreak=pre-pivot ] + [ SYSFONT = rdbreak=pre-pivot ] + [ KEYTABLE=us = rdbreak=pre-pivot ] + [ KEYTABLE = rdbreak=pre-pivot ] + [ console=ttyS0,9600 = rdbreak=pre-pivot ] + [ console = rdbreak=pre-pivot ] + [ rdinitdebug = rdbreak=pre-pivot ] + [ rdinitdebug = rdbreak=pre-pivot ] + [ rdshell = rdbreak=pre-pivot ] + [ rdshell = rdbreak=pre-pivot ] + [ rdloaddriver=sun_esp = rdbreak=pre-pivot ] + [ rdloaddriver = rdbreak=pre-pivot ] + return 1 + source_all pre-pivot + local f + [ pre-pivot ] + [ -d /pre-pivot ] + [ -e /pre-pivot/02multipathd-stop.sh ] + . /pre-pivot/02multipathd-stop.sh + [ -e /etc/multipath.conf ] + [ -e /pre-pivot/30crypt-cleanup.sh ] + . /pre-pivot/30crypt-cleanup.sh + cryptsetup luksClose /dev/mapper/luks-* + [ -e /pre-pivot/31crypt-cleanup.sh ] + . /pre-pivot/31crypt-cleanup.sh + cryptsetup luksClose /dev/mapper/luks-* + [ -e /pre-pivot/50selinux-loadpolicy.sh ] + . /pre-pivot/50selinux-loadpolicy.sh + rd_load_policy + SELINUX=enforcing + [ -e /sysroot/etc/selinux/config ] + . /sysroot/etc/selinux/config + SELINUX=enforcing + SELINUXTYPE=targeted + getarg selinux=0 + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = selinux=0 ] + [ root = selinux=0 ] + [ ro = selinux=0 ] + [ ro = selinux=0 ] + [ LANG=en_US.UTF-8 = selinux=0 ] + [ LANG = selinux=0 ] + [ SYSFONT=latarcyrheb-sun16 = selinux=0 ] + [ SYSFONT = selinux=0 ] + [ KEYTABLE=us = selinux=0 ] + [ KEYTABLE = selinux=0 ] + [ console=ttyS0,9600 = selinux=0 ] + [ console = selinux=0 ] + [ rdinitdebug = selinux=0 ] + [ rdinitdebug = selinux=0 ] + [ rdshell = selinux=0 ] + [ rdshell = selinux=0 ] + [ rdloaddriver=sun_esp = selinux=0 ] + [ rdloaddriver = selinux=0 ] + return 1 + [ 1 -eq 0 -o enforcing = disabled ] + permissive=0 + getarg enforcing=0 + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = enforcing=0 ] + [ root = enforcing=0 ] + [ ro = enforcing=0 ] + [ ro = enforcing=0 ] + [ LANG=en_US.UTF-8 = enforcing=0 ] + [ LANG = enforcing=0 ] + [ SYSFONT=latarcyrheb-sun16 = enforcing=0 ] + [ SYSFONT = enforcing=0 ] + [ KEYTABLE=us = enforcing=0 ] + [ KEYTABLE = enforcing=0 ] + [ console=ttyS0,9600 dracut: Loading SELinux policy = edracut: + [ -x /sysroot/sbin/load_policy ] ndracut: + chroot /sysroot /sbin/load_policy -i forcing=0 ] + [ console = enforcing=0 ] + [ rdinitdebug = enforcing=0 ] + [ rdinitdebug = enforcing=0 ] + [ rdshell = enforcing=0 ] + [ rdshell type=1404 audit(1275605087.863:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 = enforcing=0 ] + [ rdloaddriver=sun_esp = enforcing=0 ] + [ rdloaddriver = enforcing=0 ] + return 1 + [ 1 -eq 0 -o enforcing = permissive ] + [ -x /sysroot/usr/sbin/load_policy -o -x /sysroot/sbin/load_policy ] + ret=0 + info Loading SELinux policy + check_quiet + [ -z yes ] + echo <6>dracut: Loading SELinux policy + [ yes != yes ] + vinfo + read line + info + [ -x /sysroot/sbin/load_policy ] + check_quiet + [ -z yes ] + echo <6>dracut: + [ -x /sysroot/sbin/load_policy ] + [ yes != yes ] + read line + info + chroot /sysroot /sbin/load_policy -i + check_quiet + [ -z yes ] + echo <6>dracut: + chroot /sysroot /sbin/load_policy -i + [ yes != yes ] + read line type=1403 audit(1275605089.662:3): policy loaded auid=4294967295 ses=4294967295 + indracut: + ret=0 fo + ret=type=1404 audit(1275605089.792:4): enforcing=0 old_enforcing=1 auid=4294967295 ses=4294967295 0 + check_quiet + [ -z yes ] + echo <6>dracut: + ret=0 + [ yes != yes ] + read line + [ 0 -eq 0 -o 0 -eq 2 ] + [ -e /sysroot/.autorelabel ] + echo 0 + return 0 + [ -e /pre-pivot/90plymouth-newroot.sh ] + . /pre-pivot/90plymouth-newroot.sh + [ -x /bin/plymouth ] + /bin/plymouth --newroot=/sysroot + getarg init= + local o line + [ -z root=/dev/mapper/vg_spacely-lv_root ro LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console=ttyS0,9600 rdinitdebug rdshell rdloaddriver=sun_esp ] + [ root=/dev/mapper/vg_spacely-lv_root = init= ] + [ root = init ] + [ ro = init= ] + [ ro = init ] + [ LANG=en_US.UTF-8dracut: Switching root = init= ] + [ LANG = init ] + [ SYSFONT=latarcyrheb-sun16 = init= ] + [ SYSFONT = init ] + [ KEYTABLE=us = init= ] + [ KEYTABLE = iWelcome to Fedora Press 'I' to enter interactive startup. Starting udev: [ OK ] Setting hostname spacely.pari.edu: [ OK ] Setting up Logical Volume Management: 2 logical volume(s) in volume group "vg_spacely" now active 2 logical volume(s) in volume group "VolGroup00" now active [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/mapper/vg_spacely-lv_root /dev/mapper/vg_spacely-lv_root: clean, 205051/1105920 files, 1462230/4419584 blocks [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a /dev/sdg1 /dev/sdg1: clean, 32/50400 files, 54640/200808 blocks [ OK ] Remounting root filesystem in read-write mode: [ OK ] Mounting local filesystems: [ OK ] Enabling local filesystem quotas: [ OK ]
*** Warning -- SELinux targeted policy relabel is required. *** Relabeling could take a very long time, depending on file *** system size and speed of hard drives. ******************************************************************************* ******************************************************************************** **************************************************** + echo
+ echo
+ echo No root device found No root device found + source_all emergency + local f + [ emergency ] + [ -d /emergency ] + [ -e /emergency/50plymouth-emergency.sh ] + . /emergency/50plymouth-emergency.sh + [ -x /bin/plymouth ] + /bin/plymouth --hide-splash Enabling /etc/fstab swaps: [ OK ] Entering non-interactive startup Starting monitoring for VG VolGroup00: 2 logical volume(s) in volume group "VolGroup00" monitored [ OK ] Starting monitoring for VG vg_spacely: 2 logical volume(s) in volume group "vg_spacely" monitored [ OK ] ip6tables: Applying firewall rules: [ OK ] ip6tables: Loading additional modules: nf_conntrack_ftp nf_conntrack_netbios_ns nf_conntrack_tftp [ OK ] iptables: Applying firewall rules: [ OK ] iptables: Loading additional modules: nf_conntrack_ftp nf_conntrack_netbios_ns nf_conntrack_tftp [ OK ] Starting auditd: [ OK ] Starting portreserve: [ OK ] Starting system logger: [ OK ] Starting rpcbind: [ OK ] Starting system message bus: [ OK ] Setting network parameters... [ OK ] Starting NetworkManager daemon: [ OK ] Starting Avahi daemon... [ OK ] Starting NFS statd: [ OK ] Starting RPC idmapd: [ OK ] Starting cups: [ OK ] Mounting other filesystems: [ OK ] Starting HAL daemon: [ OK ] Starting PC/SC smart card daemon (pcscd): [ OK ] Retrigger failed udev events[ OK ] ipsec_setup: Starting Openswan IPsec U2.6.24/K2.6.32.10-90.fc12.sparc64... ipsec_setup: no default routes detected Enabling Bluetooth devices: Starting sshd: [ OK ] Starting sendmail: [ OK ] Starting sm-client: [ OK ] Starting abrt daemon: [ OK ] Starting console mouse services: [ OK ] [ OK ] crond: [ OK ] [ OK ] atd: [ OK ]
Fedora release 12 (Constantine) Kernel 2.6.32.10-90.fc12.sparc64 on an sparc64 (ttyS0)
spacely.pari.edu login: root Password: [root@spacely ~]#
On Thursday, June 03, 2010 06:29:12 pm Dennis Gilmore wrote:
On Thursday, June 03, 2010 05:07:12 pm Lamar Owen wrote:
2.) Why is dracut not finding /lib/firmware/qlogic/isp1000.bin when trying rdloaddriver=qlogicpti, which tries to load qlogic/isp1000.bin, but finds it (by the same name, qlogic/isp1000.bin) just fine when modprobe qlogicpti is typed in at the same dracut's rdshell command line?
this i'm not sure of. we should try and debug it
I've finally gotten time to play with the E6500 again this week, and here's an update.
I iteratively checked loading qlogicpti at different breakpoints (using rdbreak=), and found that the sweet spot is using rdbreak=pre-trigger in the append= line in /etc/silo.conf. So my append= for the E6500 currently is: append=" LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us console= ttyS0,9600 rdinfo rdshell rdbreak=pre-trigger rdloaddriver=sun_esp rdloaddriver= sunhme" and that breaks right after loading the other drivers; I then manually modprobe qlogicpti, which loads its firmware and finds the drives on the bus; then I type exit, the boot continues, including the LVM pieces and the /dev/root symlink, and then it breaks again right before pivot-root. Typing exit there, and it resumes normal booting.
With rdbreak=pre-udev, modprobe qlogicpti can't find its firmware; with rdbreak=pre-mount, the symlink for the root device isn't autogenerated. I didn't try rdbreak=initqueue, because I used an outside to inside search starting with pre-udev, going to pre-mount next, and then the next was pre-trigger, which worked.
I see a --fwdir option to the dracut build options; perhaps that's something to twiddle to get this fully automatic again.
-
Dennis Gilmore -
Lamar Owen -
Tom Callaway