Justin M. Forbes wrote:
Which kernel version is this? If 2135, does the problem still occur
with
2163?
This is with 2163.
It should be noted that the oopses are now periodic with the sapdb xserver
running..
Here's the most recent two.
<snip>
<0>general protection fault: 0000
CPU 0
Pid: 19398, comm: slowknl Not tainted
RIP: 0010:[<ffffffff801c85b4>]{ia32_copy_siginfo_to_user+244}
RSP: 0000:00000100e36e7e40 EFLAGS: 00010212
RAX: 0000000000000000 RBX: 0000000059374710 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 00000100e36e7f38 RDI: 00000000593747a0
RBP: 0000000000000000 R08: 00000100e335ff60 R09: 0000000000000000
R10: ffffffff8013db71 R11: 0000000000010283 R12: 00000100e36e7f58
R13: 00000100f7b28ee8 R14: 0000000000000020 R15: 00000100e36e6a58
FS: 0000002a9555c6a0(0000) GS:ffffffff80574d40(005b) knlGS:0000000059374bb0
CS: 0010 DS: 002b ES: 002b CR0: 000000008005003b
CR2: 0000000008da694c CR3: 0000000000101000 CR4: 00000000000006e0
Process slowknl (pid: 19398, stackpage=100e36e7000)
Stack: 00000100e36e7e40 0000000000000000 5557ed68801c918e 0000000400000000
59374bb000000000 0000000100000000 0000008000000000 00004bc600000000
ffffffff00000000 802c4c44ffffffff 00000010ffffffff 0001028300000000
Call Trace: [<ffffffff801101ce>]{do_signal+158}
[<ffffffff802c4c44>]{bad_get_user+0}
[<ffffffff8013db71>]{compat_sys_sched_setaffinity+17}
[<ffffffff8011061b>]{intret_signal+45}
Code: c3 66 66 66 90 66 66 66 90 66 66 90 48 83 ec 18 48 81 e2 ff
RIP [<ffffffff801c85b4>]{ia32_copy_siginfo_to_user+244} RSP
<00000100e36e7e40>
CPU 0
Pid: 19398, comm: slowknl Not tainted
RIP: 0010:[<ffffffff801c85b4>]{ia32_copy_siginfo_to_user+244}
RSP: 0000:00000100e36e7e40 EFLAGS: 00010212
RAX: 0000000000000000 RBX: 0000000059374710 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 00000100e36e7f38 RDI: 00000000593747a0
RBP: 0000000000000000 R08: 00000100e335ff60 R09: 0000000000000000
R10: ffffffff8013db71 R11: 0000000000010283 R12: 00000100e36e7f58
R13: 00000100f7b28ee8 R14: 0000000000000020 R15: 00000100e36e6a58
FS: 0000002a9555c6a0(0000) GS:ffffffff80574d40(005b) knlGS:0000000059374bb0
CS: 0010 DS: 002b ES: 002b CR0: 000000008005003b
CR2: 0000000008da694c CR3: 0000000000101000 CR4: 00000000000006e0
Process slowknl (pid: 19398, stackpage=100e36e7000)
Stack: 00000100e36e7e40 0000000000000000 5557ed68801c918e 0000000400000000
59374bb000000000 0000000100000000 0000008000000000 00004bc600000000
ffffffff00000000 802c4c44ffffffff 00000010ffffffff 0001028300000000
Call Trace: [<ffffffff801101ce>]{do_signal+158}
[<ffffffff802c4c44>]{bad_get_user+0}
[<ffffffff8013db71>]{compat_sys_sched_setaffinity+17}
[<ffffffff8011061b>]{intret_signal+45}
Code: c3 66 66 66 90 66 66 66 90 66 66 90 48 83 ec 18 48 81 e2 ff
</snip>
These go away if sapdb is stopped.
dmesg attached.
<snip>
ok
Bootdata ok (command line is ro root=LABEL=/ hdb=ide-scsi)
Linux version 2.4.22-1.2163.nptlsmp (bhcompile(a)thor.perf.redhat.com) (gcc
version 3.2.3 20030422 (Red Hat Linux 3.2.3-6)) #1 SMP Fri Jan 16 12:58:20 EST
2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000faff0000 (usable)
BIOS-e820: 00000000faff0000 - 00000000fafff000 (ACPI data)
BIOS-e820: 00000000fafff000 - 00000000fb000000 (ACPI NVS)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
kernel direct mapping tables upto 10100000000 @ 8000-d000
ACPI: have wakeup address 0x10000002000
Scan SMP from 0000010000000000 for 1024 bytes.
Scan SMP from 000001000009fc00 for 1024 bytes.
Scan SMP from 00000100000f0000 for 65536 bytes.
found SMP MP-table at 00000000000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000f9000 reserved twice.
hm, page 000fa000 reserved twice.
On node 0 totalpages: 1028080
zone(0): 4096 pages.
zone(1): 1023984 pages.
zone(2): 0 pages.
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000f4710
ACPI: XSDT (v001 A M I OEMXSDT 0x08000318 MSFT 0x00000097) @ 0x00000000faff0100
ACPI: FADT (v001 A M I OEMFACP 0x08000318 MSFT 0x00000097) @ 0x00000000faff0281
ACPI: MADT (v001 A M I OEMAPIC 0x08000318 MSFT 0x00000097) @ 0x00000000faff0380
ACPI: OEMB (v001 A M I OEMBIOS 0x08000318 MSFT 0x00000097) @ 0x00000000fafff040
ACPI: ASF! (v001 AMIASF AMDSTRET 0x00000001 INTL 0x02002026) @ 0x00000000faff3580
ACPI: DSDT (v001 0ABCF 0ABCF007 0x00000007 INTL 0x02002026) @ 0x0000000000000000
ACPI: Parsing Local APIC info in MADT
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:5 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:5 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23
ACPI: IOAPIC (id[0x03] address[0xfebfe000] global_irq_base[0x18])
IOAPIC[1]: Assigned apic_id 3
IOAPIC[1]: apic_id 3, version 17, address 0xfebfe000, IRQ 24-27
ACPI: IOAPIC (id[0x04] address[0xfebff000] global_irq_base[0x1c])
IOAPIC[2]: Assigned apic_id 4
IOAPIC[2]: apic_id 4, version 17, address 0xfebff000, IRQ 28-31
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ 3fe0000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Kernel command line: ro root=LABEL=/ hdb=ide-scsi
ide_setup: hdb=ide-scsi
Initializing CPU#0
time.c: Detected 1.193182 MHz PIT timer.
time.c: Detected 1591.558 MHz TSC timer.
Console: colour VGA+ 80x25
Calibrating delay loop... 3171.94 BogoMIPS
Memory: 4017576k/4112320k available (1858k kernel code, 94356k reserved, 1603k
data, 160k init)
Dentry cache hash table entries: 131072 (order: 9, 2097152 bytes)
Inode cache hash table entries: 131072 (order: 9, 2097152 bytes)
Mount cache hash table entries: 256 (order: 0, 4096 bytes)
Buffer cache hash table entries: 262144 (order: 9, 2097152 bytes)
Page-cache hash table entries: 262144 (order: 9, 2097152 bytes)
CPU: L1 I Cache: 64K (64 bytes/line/2 way), D cache 64K (64 bytes/line/2 way)
CPU: L2 Cache: 1024K (64 bytes/line/1 way)
Machine Check Reporting enabled for CPU#0
POSIX conformance testing by UNIFIX
mtrr: v2.02 (20020716))
CPU: L1 I Cache: 64K (64 bytes/line/2 way), D cache 64K (64 bytes/line/2 way)
CPU: L2 Cache: 1024K (64 bytes/line/1 way)
CPU0: AMD Opteron(tm) Processor 242 stepping 01
per-CPU timeslice cutoff: 5120.94 usecs.
task migration cache decay timeout: 10 msecs.
Booting processor 1/1 rip 6000 page 00000100066ac000
Initializing CPU#1
Calibrating delay loop... 3178.49 BogoMIPS
CPU: L1 I Cache: 64K (64 bytes/line/2 way), D cache 64K (64 bytes/line/2 way)
CPU: L2 Cache: 1024K (64 bytes/line/1 way)
Machine Check Reporting enabled for CPU#1
CPU1: AMD Opteron(tm) Processor 242 stepping 01
Total of 2 processors activated (6350.43 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23,
3-0, 3-1, 3-2, 3-3, 4-0, 4-1, 4-2, 4-3 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 4.
number of IO-APIC #4 registers: 4.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 02000000
....... : arbitration: 02
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
.... register #01: 00030011
....... : max redirection entries: 0003
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
.... register #01: 00030011
....... : max redirection entries: 0003
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
Detected 12.434 MHz APIC timer.
cpu: 0, clocks: 1989447, slice: 663149
CPU0<T0:1989440,T1:1326288,D:3,S:663149,C:1989447>
cpu: 1, clocks: 1989447, slice: 663149
CPU1<T0:1989440,T1:663136,D:6,S:663149,C:1989447>
checking TSC synchronization across CPUs: passed.
testing NMI watchdog ... OK.
time.c: Using PIT/TSC based timekeeping.
Starting migration thread for cpu 0
smp_num_cpus: 2.
Starting migration thread for cpu 1
ACPI: Subsystem revision 20031002
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
PCI: Using configuration type 1
PCI: Probing PCI hardware
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16) Mode:1 Active:1
00:00:07[A] -> 2-16 -> vector 0xa9 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17) Mode:1 Active:1
00:00:07[B] -> 2-17 -> vector 0xb1 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18) Mode:1 Active:1
00:00:07[C] -> 2-18 -> vector 0xb9 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19) Mode:1 Active:1
00:00:07[D] -> 2-19 -> vector 0xc1 -> IRQ 19
Pin 2-19 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-17 already programmed
IOAPIC[1]: Set PCI routing entry (3-3 -> 0xc9 -> IRQ 27) Mode:1 Active:1
00:02:08[A] -> 3-3 -> vector 0xc9 -> IRQ 27
IOAPIC[1]: Set PCI routing entry (3-0 -> 0xd1 -> IRQ 24) Mode:1 Active:1
00:02:08[B] -> 3-0 -> vector 0xd1 -> IRQ 24
IOAPIC[1]: Set PCI routing entry (3-1 -> 0xd9 -> IRQ 25) Mode:1 Active:1
00:02:08[C] -> 3-1 -> vector 0xd9 -> IRQ 25
IOAPIC[1]: Set PCI routing entry (3-2 -> 0xe1 -> IRQ 26) Mode:1 Active:1
00:02:08[D] -> 3-2 -> vector 0xe1 -> IRQ 26
Pin 3-2 already programmed
Pin 3-3 already programmed
Pin 3-0 already programmed
Pin 3-1 already programmed
Pin 3-0 already programmed
Pin 3-1 already programmed
Pin 3-0 already programmed
Pin 3-1 already programmed
IOAPIC[2]: Set PCI routing entry (4-0 -> 0xe9 -> IRQ 28) Mode:1 Active:1
00:01:03[A] -> 4-0 -> vector 0xe9 -> IRQ 28
IOAPIC[2]: Set PCI routing entry (4-1 -> 0x32 -> IRQ 29) Mode:1 Active:1
00:01:03[B] -> 4-1 -> vector 0x32 -> IRQ 29
IOAPIC[2]: Set PCI routing entry (4-2 -> 0x3a -> IRQ 30) Mode:1 Active:1
00:01:03[C] -> 4-2 -> vector 0x3a -> IRQ 30
IOAPIC[2]: Set PCI routing entry (4-3 -> 0x42 -> IRQ 31) Mode:1 Active:1
00:01:03[D] -> 4-3 -> vector 0x42 -> IRQ 31
Pin 4-1 already programmed
Pin 4-2 already programmed
Pin 4-3 already programmed
Pin 4-0 already programmed
Pin 4-1 already programmed
Pin 4-2 already programmed
Pin 4-3 already programmed
Pin 4-0 already programmed
Pin 4-2 already programmed
Pin 4-3 already programmed
Pin 4-0 already programmed
Pin 4-1 already programmed
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 3852M
agpgart: no supported devices found.
PCI-DMA: Disabling IOMMU.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
IA32 emulation $Id: sys_ia32.c,v 1.62 2003/09/22 04:25:53 ak Exp $
initialize_kbd: Keyboard reset failed, no ACK
Detected PS/2 Mouse Port.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 00:07.1
AMD8111: chipset revision 3
AMD8111: not 100% native mode: will probe irqs later
AMD_IDE: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03) UDMA100 controller
on pci00:07.1
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
hdb: LITE-ON LTR-52327S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 16384 buckets, 256Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
3ware Storage Controller device driver for Linux v1.02.00.036.
scsi0 : Found a 3ware Storage Controller at 0xac00, IRQ: 26, P-chip: 1.3
scsi0 : 3ware Storage Controller
blk: queue 0000010037f10030, no I/O memory limit
Vendor: 3ware Model: Logical Disk 0 Rev: 1.0
Type: Direct-Access ANSI SCSI revision: 00
blk: queue 00000100f9fade30, no I/O memory limit
Vendor: 3ware Model: Logical Disk 6 Rev: 1.0
Type: Direct-Access ANSI SCSI revision: 00
blk: queue 00000100f9fadc30, no I/O memory limit
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi disk sdb at scsi0, channel 0, id 6, lun 0
SCSI device sda: 1953599360 512-byte hdwr sectors (1000243 MB)
Partition check:
sda: sda1
SCSI device sdb: 234439600 512-byte hdwr sectors (120033 MB)
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 >
libata version 0.81 loaded.
sata_promise version 0.87
ata1: SATA max UDMA/133 cmd 0xFFFFFF000001A200 ctl 0xFFFFFF000001A238 bmdma
0x0 irq 17
ata2: SATA max UDMA/133 cmd 0xFFFFFF000001A280 ctl 0xFFFFFF000001A2B8 bmdma
0x0 irq 17
ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 72303840 sectors (lba48)
ata1: dev 0 configured for UDMA/133
ata2: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 72303840 sectors (lba48)
ata2: dev 0 configured for UDMA/133
scsi1 : sata_promise
scsi2 : sata_promise
Vendor: ATA Model: WDC WD360GD-00FN Rev: 0.81
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD360GD-00FN Rev: 0.81
Type: Direct-Access ANSI SCSI revision: 05
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 >
libata version 0.81 loaded.
sata_promise version 0.87
ata1: SATA max UDMA/133 cmd 0xFFFFFF000001A200 ctl 0xFFFFFF000001A238 bmdma
0x0 irq 17
ata2: SATA max UDMA/133 cmd 0xFFFFFF000001A280 ctl 0xFFFFFF000001A2B8 bmdma
0x0 irq 17
ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 72303840 sectors (lba48)
ata1: dev 0 configured for UDMA/133
ata2: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 72303840 sectors (lba48)
ata2: dev 0 configured for UDMA/133
scsi1 : sata_promise
scsi2 : sata_promise
Vendor: ATA Model: WDC WD360GD-00FN Rev: 0.81
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: WDC WD360GD-00FN Rev: 0.81
Type: Direct-Access ANSI SCSI revision: 05
Attached scsi disk sdc at scsi1, channel 0, id 0, lun 0
Attached scsi disk sdd at scsi2, channel 0, id 0, lun 0
SCSI device sdc: 72303840 512-byte hdwr sectors (37020 MB)
sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 >
SCSI device sdd: 72303840 512-byte hdwr sectors (37020 MB)
sdd: sdd1 sdd2 sdd3 sdd4 < sdd5 sdd6 sdd7 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 160k freed
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
ACPI: Processor [CPU2] (supports C1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xffffff000001c000, IRQ 19
usb-ohci.c: usb-03:00.0, Advanced Micro Devices [AMD] AMD-8111 USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xffffff000001e000, IRQ 19
usb-ohci.c: usb-03:00.1, Advanced Micro Devices [AMD] AMD-8111 USB (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech(a)suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,19), internal journal
Adding Swap: 8385920k swap-space (priority -1)
hub.c: new USB device 03:00.0-2, assigned address 2
input: USB HID v1.10 Keyboard [HEWLETT PACKARD USB Keyboard ] on usb1:2.0
input,hiddev0: USB HID v1.10 Device [HEWLETT PACKARD USB Keyboard ] on usb1:2.1
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,21), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,22), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,23), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hdb: attached ide-scsi driver.
scsi3 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: LITE-ON Model: LTR-52327S Rev: QS03
Type: CD-ROM ANSI SCSI revision: 02
</snip>
--
Ken Snider