SATA optical drives
by David Fletcher
I'm currently running FC5, will probably upgrade to F7 in a couple of months.
Unfortunately my CD/DVD rewriter appears to have died, before it's
even seen a dual layer disk :'(
SATA hard drives run without problems for me, but now that SATA
optical drives are starting to appear in the shops, would it be OK to
buy one of these and get rid of another wide ribbon cable?
Is anybody already running them with Fedora?
Thanks for any advice/experiences.
Dave F
3 months, 1 week
Changing date with procmail
by Michael A. Peters
Anyone know of a procmail recipe to change the date on incoming
messages?
If the date is in the future by more than 24 hours - I'd like to just
change it to the current date.
If the date is in the past by more than two weeks - I'd like to just
change it to the current date.
I'd like to do it in procmail - if someone knows how.
I've done some searching, still have some to do.
Found some stuff on extracting the date, but not on modifying it if
necessary.
1 year, 3 months
VPN options
by Keith Lofstrom
I am planning on running a Virtual Private Network from my Fedora
firewall out to a UML virtual colo (running RH9) at another site.
That site will be the place I present services to the world;
httpd, ssh, sftp, smtp. This is to comply with the "no servers"
and dynamic ip restrictions on my Comcast connection to the net;
if my firewall always drives an outbound connection to the
colocation site, I am not worried about changes of ip address,
and I am not opening any inbound ports.
There are a number of options for the VPN - the most attractive
are cipe ( http://sites.inka.de/sites/bigred/devel/cipe.html )
and FreeSwan ( http://www.freeswan.org/ ), though I am told that
one can do all this through an ssh tunnel. I would rather have
simple and secure than super-duper; I have plenty of bandwidth,
and will send outbound http and smtp from the firewall, so the
main bandwidth user will be incoming spam/b/b/b/b mail.
Anyone have some experiences to share about setting up VPN? Is
there anything about either cipe or FreeSwan that is likely to
break with FC1 or FC2?
Keith
--
Keith Lofstrom keithl(a)ieee.org Voice (503)-520-1993
KLIC --- Keith Lofstrom Integrated Circuits --- "Your Ideas in Silicon"
Design Contracting in Bipolar and CMOS - Analog, Digital, and Scan ICs
3 years, 10 months
Problems with 3COM 3C900Combo
by Christian Moller
Hi all Fedora users,
I have just joined this list. I am running the latest Fedora but I can't get
my 3C900Combo networking card to work. I can see that the card is installed
but no IP-address is asigned to it and I can't set it. So I think that there
is a bug in that driver. Any other user out there who have a solution for
this?
Best regards and thanks,
Christian
8 years, 4 months
RAGE XL Framebuffer
by Yanick Quirion
Hi all
I know that is not a specific question about Fedora, but I can't find answer on the kernel mailing list.
Is somebody having server with integrated ATI RAGE XL video card? Is it possible to patch the kernel to support this video card? If I add VGA=791 in my grub.conf, I will have a resolution of 1024x768 which is good, but the display is very slow (especially when the screen is scrolling). If I use I this: "video=aty128fb:1024x768@70" it will not work. I'm using kernel 2.4.22 but I will try 2.6.0-test11 today.
If somebody has a patch, a link or anything else that can help me, it will be appreciated.
Thanks for your help.
Regards,
-----------
Yanick Quirion
Administrateur Réseau/Network Manager
NEOKIMIA INC.
Institut de Pharmacologie de Sherbrooke
3e étage (Édifice Z5)
3001 12e avenue Nord
Sherbrooke, Québec
CANADA
J1H 5N4
Tél.: +1 819 820-6040
Direct: +1 819 820-6855
Fax.: +1 819 820-6841
email: Yanick.Quirion(a)neokimia.com
8 years, 4 months
Soundblaster
by Antonio Montagnani
I have two similar PC (old Pentium but workin fine)
In Pc no.1 I upgraded from RH8 to Fedora and it went fine: Soundblaster
is working fine
In Pc no.2 I made a fresh installation but in redhat-sound-config Fedora
doesn't see any card, that was working on Redhat 9 after soundconfig...
Where is the trick?? I assume that my Sounblaster is an old 16...but
fine on a router/firewall.
Tnx
Antonio
8 years, 4 months
Linux software for Motorola Razor phone?
by William W. Austin
This may have been answered before, but scanning the archives, I
haven't found it (sorry...).
My wife recently surprised me with a new gsm phone, a Motorola Razor.
I already had the USB cable which works with it (use it with my
camcorder), but a web search for Linux software to use the phone with
one of my Linux boxen didn't turn up anything. Basically I want to
synchronize the calendar and phonebooks, and be able to back up files
from the phone to the computer (and restore). I'm running both FC4 and
FC5 here so anything which would work with either of those would be
great - and much apprecited.
Thanks in advance,
--
william w. austin waustin(a)speakeasy.net
"life is just another phase i'm going through. this time, anyway ..."
13 years, 9 months
Network problems on new FC4 box - please help.
by William W. Austin
I had to replace a disk (the one with all of the home directories on
it) on an FC3 box, and so I bought a new drive (particulars
unimportant).
To make a long story short, I decided to put FC4 on this box, and so I
installed the new drive and put the root filesystem on it. I still
have the old FC3 root drive and can boot to either for comparison...
Under FC3, I have no network problems that I can detect; however, under
FC4 there are two distinct (related? no idea) problems which have
eluded me. I have tried looking up both of these in the archives, but
have had no luck (some similar issues, but nothing exactly like either
of these unless I missed them).
Problem 1: network card goes to sleep.
This machine has 2 network cards, both on-board. The 1GB card L(Intel
82540EM) goes to the smartswitch to tolk to the local network, and does
not show any problems.
The other card (nVidia nForce2) is a 100MB card and talks to the DSL
modem. Periodically I cannot connect to the internet at all - or even
ping the DSL modem. This happens irregularly but about 5-10 times/day.
If I reboot back to FC3, the problem does not occur. Network
configurations between the two (FC3/FC4) are as identical as I can make
them. The first few times the problem occurs, sometimes retarting
networking works, but eventually a full sys reboot is the only thing
which works.
Problem 2: slow local network.
Under FC3 throughput on the LOCAL network (1GB lan) is very fast.
Under FC4, the best I have seen is ONE transfer of about 1.2 MB/s - and
throughput drops to as low as 50-75KB/s at times. Again, this does not
occur under FC3 but does under FC4. Again the same setup as nearly as
I can make it. No workaround found so far.
Any suggestions would be greatly appreciated.
--
william w. austin waustin(a)speakeasy.net
"life is just another phase i'm going through. this time, anyway ..."
13 years, 9 months
X and Intel 965
by Jeffrey Ross
so far the installation of FC6 has gone relatively smoothly albeit some
additional learning and bumps due to the 64 bit architecture of this
machine.
The mother board is an Intel DG965RYCK which uses Intel's 965 express
chipset. Based upon what I've been able to find on the web, Intel has
released the drivers for this chipset to OSS, although there have been
issues as to what Intel actually released and how complete they might be.
Regardless I unable to run mplayer (or Realplayer) for that matter
without the display first freezing then going black followed by garbage
along the bottom of the screen. A Control-Alt-Backspace does not stop X
from running. The only way to recover the machine from this point is to
reboot the system. I am still able to connect from a remote system, its
just the display that has become unstable.
lspci -v shows the following for the graphics adapter
00:02.0 VGA compatible controller: Intel Corporation Integrated
Graphics Controller (rev 02) (prog-if 00 [VGA])
Subsystem: Intel Corporation Unknown device 514d
Flags: bus master, fast devsel, latency 0, IRQ 177
Memory at 50200000 (32-bit, non-prefetchable) [size=1M]
Memory at 40000000 (64-bit, prefetchable) [size=256M]
I/O ports at 3110 [size=8]
Capabilities: [90] Message Signalled Interrupts: 64bit-
Queue=0/0 Enable-
Capabilities: [d0] Power Management version 2
suggestions would be appreciated.
Thanks
14 years, 11 months
vstpd.conf
by dhottinger＠harrisonburg.k12.va.us
Im having a devil of a time getting vsftpd configured for auth. with
an ldap backend on Fedora Core 5. I keep getting a 530 530 Login
incorrect.
Unable to make a connection. Please try again.
The server has a username incorrect message.
Anonymous works fine. I have standard vsftpd.conf here is the snippet:
anonymous_enable=No
#
# Uncomment this to allow local users to log in.
local_enable=YES
#
# Uncomment this to enable any form of FTP write command.
write_enable=YES
#
# Default umask for local users is 077. You may wish to change this to 022,
# if your users expect that (022 is used by most other ftpd's)
local_umask=022
#
# Uncomment this to allow the anonymous FTP user to upload files. This only
# has an effect if the above global write enable is activated. Also, you will
# obviously need to create a directory writable by the FTP user.
#anon_upload_enable=YES
#
# Uncomment this if you want the anonymous FTP user to be able to create
# new directories.
#anon_mkdir_write_enable=YES
#
# Activate directory messages - messages given to remote users when they
# go into a certain directory.
dirmessage_enable=YES
#
# Activate logging of uploads/downloads.
xferlog_enable=YES
ascii_upload_enable=YES
ascii_download_enable=YES
#
# You may fully customise the login banner string:
#ftpd_banner=Welcome to blah FTP service.
#
# You may specify a file of disallowed anonymous e-mail addresses. Apparently
# useful for combatting certain DoS attacks.
#deny_email_enable=YES
# (default follows)
#banned_email_file=/etc/vsftpd.banned_emails
#
# You may specify an explicit list of local users to chroot() to their home
# directory. If chroot_local_user is YES, then this list becomes a list of
# users to NOT chroot().
chroot_local_user=YES
#chroot_list_enable=YES
# (default follows)
#chroot_list_file=/etc/vsftpd.chroot_list
#
# You may activate the "-R" option to the builtin ls. This is disabled by
# default to avoid remote users being able to cause excessive I/O on large
# sites. However, some broken FTP clients such as "ncftp" and "mirror" assume
# the presence of the "-R" option, so there is a strong case for enabling it.
ls_recurse_enable=YES
pam_service_name=vsftp
userlist_enable=YES
#enable for standalone mode
listen=YES
tcp_wrappers=YES
User authentication is against an ldap server. That seems to be
working fine. AFP users can connect ok. I read about an issue with
the pam module, but that doesnt seem to be the case. I keep beating
this thing around and around with no joy so far.
--
Dwayne Hottinger
Network Administrator
Harrisonburg City Public Schools
15 years, 2 months
