Re: failed to ..
by Patrick Dupre
Hello,
I tried to set relabel by using system-config-selinux,
but nothing happens I have to keep selinux=0 to be able to boot!
>
> On Sat, 28 Dec 2013 16:28:33 +0100, Patrick Dupre wrote:
>
> > (I did not have a rsync command on the gparted live distribution that I have)
>
> Does its "cp" command copy SELinux file contexts?
>
> > And I get always the same behavior:
> > failed to start .......
> > create static device modes in /dev
> > journal service
> > open pack file: permission denied
>
> Is this with SELinux enforcing or permissive or disabled?
> --
> users mailing list
> users(a)lists.fedoraproject.org
> To unsubscribe or change subscription options:
> https://admin.fedoraproject.org/mailman/listinfo/users
> Fedora Code of Conduct: http://fedoraproject.org/code-of-conduct
> Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
> Have a question? Ask away: http://ask.fedoraproject.org
===========================================================================
Patrick DUPRÉ | | email: pdupre(a)gmx.com
Laboratoire de Physico-Chimie de l'Atmosphère | |
Université du Littoral-Côte d'Opale | |
Tel. (33)-(0)3 28 23 76 12 | | Fax: 03 28 65 82 44
189A, avenue Maurice Schumann | | 59140 Dunkerque, France
===========================================================================
5 years, 5 months
Fedora 20 Problems on Dell XPS 41z
by Dave Cross
A couple of weeks ago, I posted a really happy email about how well
the upgrade from F19 to F20 had gone on my laptop. Now, I'm not so
happy. There are two problems that are close to being deal-breakers
for me.
1/ The laptop doesn't wake from suspension
I close my laptop and it goes to sleep. When I open it, I expect it to
wake up again. This has worked well on every laptop I've owned on
every version of Fedora, until now. Now when I open the laptop, I'm
just presented with a small Fedora logo in the middle of the screen.
And all I can do is restart the laptop.
2/ Wifi is really flaky
Wifi has become a bit of a lottery. It's just not solid enough to rely
on. Every so often it just stops working. The icon in the notification
bar doesn't change, I just lose all connectivity. The only solution
I've found is to turn the wireless off and back on again. But it can
take five or six attempts for the wifi to reconnect. And when it does
reconnect, half of the time it will drop again within minutes. The
rest of the time I'll get a pretty solid connection that will work for
a few hours before it drops and I have to go though the same cycle
again.
This was starting to be a problem before I upgraded. But Fedora 20 has
made it far worse. Booting the laptop into Windows gives me a
rock-solid connection. And my desktop (also connecting wirelessly and
running Fedora 20) seems far more reliable. It's just the wifi driver
in the laptop that's a problem.
I realise that I haven't given you enough to go on here, but these
kinds of problems are well outside my Linux experience. Tell me what
diagnostics will we helpful and I'll provide them.
Cheers,
Dave...
--
Dave Cross :: dave(a)dave.org.uk
http://dave.org.uk/
@davorg
5 years, 5 months
upgrade fedora 19 to fedora 20 issue with GPG key
by Rafnews
Hi,
before posting on this forum, i checked on internet for this issue and
found several cause and solutions.
i tried several of them but till now none of them worked.
when i try to update fedora 19 to fedora 20 (/fedup --network 20/) i get
the following error message:
/finding updates 100%
[=======================================================================================================================================]//
//verify local files 100%
[====================================================================================================================================]//
//warning:
/var/tmp/system-upgrade/rpmfusion-free/packages/rpmfusion-free-release-20-1.noarch.rpm:
Header V3 RSA/SHA256 Signature, key ID ae688223: NOKEY//
//Importing GPG key 0xAE688223://
// Userid : "RPM Fusion free repository for Fedora (20)
<rpmfusion-buildsys(a)lists.rpmfusion.org>"//
// Fingerprint: 0017 ddfe fd13 2929 9d55 b1d3 963a 8848 ae68 8223//
// Package : rpmfusion-free-release-19-1.noarch (installed)//
// From : /etc/pki/rpm-gpg/RPM-GPG-KEY-rpmfusion-free-fedora-20//
//
//Downloading failed: Didn't install any keys/
i tried:
1. yum --enablerepo=updates-testing update fedup
but it didn't help
2. rpm --import /etc/pki/rpm-gpg/RPM-GPG-KEY-rpmfusion-nonfree-fedora-20
but it didn't help
3. fedup-cli --network 20 --nogpgcheck
install things and reboot with error. After complete restart, uname -a
still shows fedora 19 as version of fedora :(
4. rpm -qi fedup
it returns:
/Name : fedup//
//Version : 0.8.0//
//Release : 3.fc19//
//Architecture: noarch//
//Signature : RSA/SHA256, jeu. 12 déc. 2013 16:22:34 CET, Key ID
07477e65fb4b18e6//
//Source RPM : fedup-0.8.0-3.fc19.src.rpm//
////
/so it is the latest version of fedup according to documentation.
therefore what is wrong ?
thx.
5 years, 5 months
GNOME questions on fc20
by Alex
Hi, I have fc20 installed successfully on my desktop.
How can I configure the clock at the top to show the date? Why would
it be so difficult to do such a simple thing? I googled a bit, and saw
a reference to editing dateMenu.js, but the suggestions didn't work. I
can't believe I'd have to edit a text file to adjust the clock?!
I get the whole thing with not being able to (easily) minimize
applications. I know I can also switch between them with alt-tab. I
also know I can select them from "Activities", but that's an extra two
steps. Is there any way to "dock" apps like we used to be able to, so
I can select them with the mouse to choose between them?
Thanks,
Alex
5 years, 5 months
Weird USB interactions?
by Tom Horsley
When I use my AVRISPmkII programmer to fool with the
microcode on my 3D printer motherboard, my mouse and
keyboard apparently get reset. All the settings I made
with xinput disappear and I have to re-apply them.
The ISP is running through the same powered hub as the
keyboard and mouse, maybe something is resetting more
of the USB tree than it should?
Should I report this as a kernel bug? Should I try to
find more information to gather? What is going on here?
5 years, 5 months
3G dongle getting detected as USB disk on Fedora 18
by Soham Chakraborty
Afternoon folks,
I know that Fedora 18 is kinda obsolete but for a number of reasons, I have
to stick to it for the time being. However, I am quite sure that this
problem/behavior isn't restricted to F18. But since I am using that, ought
to say that.
So, here is the problem.
I have a ZTE K3800 dongle which I use for wireless/3G connection, provided
by Vodafone. When I plugin the device, it prompts to connect and works.
Problem is, as soon as I connect, systemd sends a signal 15 to
network-manager and the applet disappears from system tray. Therefore, if I
try to configure VPN, I find no option. Note that, I am only trying to
configure from the nm-applet.
lsusb shows me this
Bus 001 Device 005: ID 19d2:0117 ZTE WCDMA Technologies MSM
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x19d2 ZTE WCDMA Technologies MSM
idProduct 0x0117
bcdDevice 0.00
iManufacturer 3 ZTE,Incorporated
iProduct 2 ZTE WCDMA Technologies MSM
iSerial 4 MF6560ZTED010000
Now, when I insert the device, I get this.
Jan 1 18:50:52 blah kernel: [22130.542240] usb 1-1.2: new high-speed USB
device number 8 using ehci-pci
Jan 1 18:50:52 blah kernel: [22130.564586] nouveau W[
PFIFO][0000:01:00.0] INTR 0x00000100: 0x00000011
Jan 1 18:50:52 blah kernel: [22130.629979] usb 1-1.2: New USB device
found, idVendor=19d2, idProduct=0154
Jan 1 18:50:52 blah kernel: [22130.629986] usb 1-1.2: New USB device
strings: Mfr=3, Product=2, SerialNumber=4
Jan 1 18:50:52 blah kernel: [22130.629990] usb 1-1.2: Product: ZTE WCDMA
Technologies MSM
Jan 1 18:50:52 blah kernel: [22130.629994] usb 1-1.2: Manufacturer:
ZTE,Incorporated
Jan 1 18:50:52 blah kernel: [22130.629997] usb 1-1.2: SerialNumber:
MF6560ZTED010000
Jan 1 18:50:52 blah kernel: [22130.631836] usb-storage 1-1.2:1.0: USB Mass
Storage device detected
Jan 1 18:50:52 blah kernel: [22130.631937] scsi10 : usb-storage 1-1.2:1.0
Jan 1 18:50:52 blah mtp-probe[12945]: checking bus 1, device 8:
"/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2"
Jan 1 18:50:52 blah mtp-probe[12945]: bus: 1, device: 8 was not an MTP
device
Jan 1 18:50:52 blah kernel: [22130.689135] nouveau W[
PFIFO][0000:01:00.0] INTR 0x00000100: 0x00000011
Jan 1 18:50:52 blah kernel: [22130.813677] nouveau W[
PFIFO][0000:01:00.0] INTR 0x00000100: 0x00000011
Jan 1 18:50:53 blah kernel: [22130.938233] nouveau W[
PFIFO][0000:01:00.0] INTR 0x00000100: 0x00000011
Jan 1 18:50:53 blah kernel: [22131.062770] nouveau W[
PFIFO][0000:01:00.0] INTR 0x00000100: 0x00000011
Jan 1 18:50:53 blah logger: usb_modeswitch: using overriding config file
/etc/usb_modeswitch.d/19d2:0154; make sure this is intended
Jan 1 18:50:53 blah logger: usb_modeswitch: please report any new or
corrected settings; otherwise, check for outdated files
Jan 1 18:50:53 blah kernel: [22131.187307] nouveau W[
PFIFO][0000:01:00.0] INTR 0x00000100: 0x00000011
Jan 1 18:50:53 blah kernel: [22131.311846] nouveau W[
PFIFO][0000:01:00.0] INTR 0x00000100: 0x00000011
Jan 1 18:50:53 blah usb_modeswitch: switching device 19d2:0154 on 001/008
Note that it switches to 19d2:0154 which is
# cat /etc/usb_modeswitch.d/19d2\:0154
# ZTE MF190 (Variant) and others
TargetVendor= 0x19d2
TargetProductList="0017,0117"
MessageContent="5553424312345678000000000000061e000000000000000000000000000000"
MessageContent2="5553424312345679000000000000061b000000020000000000000000000000"
NeedResponse=1
I checked in /lib/udev/rules.d/ to see whether I can find anything but not
much success.
BTW, this article gives some clues but I don't have the configPack.tar.gz
file to clone.
http://simko.home.cern.ch/simko/usb-3g-modem.html
Any help will be appreciated. Also, if any other information is required,
do shout and I will provide.
Thanks,
Soham
5 years, 5 months
screen brightness
by Patrick Dupre
Hello,
I did not find a way to control the screen brightness of a laptop in live.
xbacklight -set 90
does not work!
Thank.
===========================================================================
Patrick DUPRÉ | | email: pdupre(a)gmx.com
Laboratoire de Physico-Chimie de l'Atmosphère | |
Université du Littoral-Côte d'Opale | |
Tel. (33)-(0)3 28 23 76 12 | | Fax: 03 28 65 82 44
189A, avenue Maurice Schumann | | 59140 Dunkerque, France
===========================================================================
5 years, 5 months
blueman/bluez in F20
by Ranjan Maitra
Hi,
I have been using blueman intermittently (as needed) for the past few
Fedora distributions but now it appears that that has been obsoleted
for F20. I was wondering what the best way for getting this to work is?
Is there any resource where I can turn to for some help?
I tried bluetooth-wizard and got it to recognize (only) some bluetooth
devices but how do I get to connect to those after that was not at all
clear to me. There used to be something called blueman-manager or
something like that. Is there something equivalent to that?
Many thanks and best wishes,
Ranjan
--
Important Notice: This mailbox is ignored: e-mails are set to be
deleted on receipt. Please respond to the mailing list if appropriate.
For those needing to send personal or professional e-mail, please use
appropriate addresses.
____________________________________________________________
GET FREE SMILEYS FOR YOUR IM & EMAIL - Learn more at http://www.inbox.com/smileys
Works with AIM®, MSN® Messenger, Yahoo!® Messenger, ICQ®, Google Talk™ and most webmails
5 years, 5 months
Used fedup . What happened?
by dave peters
I attempted to upgrade from F19 to F20. I used a dvd of F20 (x64) and
ran:
fedup --device
All appeared to go as I would expect. However, uname now gives me:
Linux localhost.localdomain 3.12.5-200.fc19.x86_64 #1 SMP Tue Dec 17
22:21:14 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux.
What have I done? What should I do next? I can restore the previous F19
(I hope)
Thanks
5 years, 5 months
