Re: WUSB54G firmware

[Jim]

I forgot to tell you that in menuconfig

<M> Prism54 USB Support    (So it is enabled in Kernel)

On 06/01/2009 12:15 PM, Jim wrote:
> On 05/31/2009 01:36 PM, Suvayu Ali wrote:
> > Jim wrote:
> > > On 05/31/2009 02:21 AM, Paulo Cavalcanti wrote:
> > > > On Sat, May 30, 2009 at 10:47 PM, Jim <[e-mail] 
> > > > > wrote:
> > > > FC10/Kde
> > > >
> > > > I'm trying to setup a Linksys WUSB54G and I get this error message
> > > > from DMESG.
> > > >
> > > > usb 2-2: firmware: requesting l3886usb
> > > >
> > > > usb 2-2: (p54usb) cannot find firmware (isl3886usb)
> > > >
> > > > usb 2-2: firmware: requesting isl3890usb
> > > >
> > > > p54usb: probe of 2-2:1.0 failed with error -2
> > > > usbcore: registered new interface driver p54usb
> > > >
> > > >
> > > > I have googled isl3886USB and can't find the firmware, does anyone
> > > > know where this firmware
> > > > is.
> > > >
> > > >
> > > > I am pretty sure I used one of those on F8, and it worked out of 
> > > > the box.
> > > >
> > > > Anyway, take a look at
> > > >
> > > > http://markmail.org/message/oqgtvzwxholc5dsl
> > > >
> > > > which will take you to:
> > > >
> > > > http://wireless.kernel.org/en/users/Drivers/p54
> > > >
> > > > -- 
> > > > Paulo Roma Cavalcanti
> > > > LCG - UFRJ
> > >
> > > I should have told you that I'm trying install on a X86_64 box.
> > >
> > > I did install the 2.13.24.0.lm86(2).arm and it is in /lib/firmware, 
> > > it would not install in
> > > /lib64/firmware.
> > >
> > > I think I need to install the ndiswrapper for i386, I have 
> > > ndiswrapper.X86_64 installed.
> > >
> > > The ndiswrapper.i386 doesn't show up in FC10 X86_64 fedora repo how 
> > > do I change the repo's to read the i386 files ?
> >
> > I think you missed a crucial step. Although right now I am using a 
> > D-Link USB wifi receiver, I did try a Linksys for a few days after I 
> > had set it up for the D-Link, and it worked right out of the box. So 
> > the procedure should be the same. Here is how I did it for the D-Link.
> > I put the firmware in /lib/firmware/
> > Renamed it to 'isl3890usb'
> > in /lib/modules/`uname -r`/build/ ran "make menuconfig" as root,
> >
> > enabled the relevant kernel module. then did a "modprobe <driver>". 
> > Here <driver> is p54.
> >
> > I believe you missed the renaming the firmware part.
> >
> > HTH
> >
> > PS: I am on x86_64 too
> > $uname -r
> > 2.6.27.24-170.2.68.fc10.x86_64
>
> I did as you suggested, but I'm still having problems.
> Do you know what this means?
>
> p54usb: probe of 2-2:1.0 failed with error -110
>
> Here is my dmesg and lsmod
>
> Dmesg
>
> usb 2-2: (p54usb) cannot find firmware (isl3886usb)
> usb 2-2: firmware: requesting isl3890usb
> phy0: p54 detected a LM86 firmware
> p54: rx_mtu reduced from 3240 to 2392
> phy0: FW rev 2.13.24.0 - Softmac protocol 5.9
> phy0: cryptographic accelerator WEP:YES, TKIP:YES, CCMP:YES
>
> p54usb: probe of 2-2:1.0 failed with error -110
> usbcore: registered new interface driver p54usb
>
> Modules that are loading
>
> p54usb                 14208  0
> p54common              20452  1 p54usb
> mac80211              194224  2 p54usb,p54common