Re: liveusb-creator

[Lawrence E Graves]

On 09/25/2016 01:54 PM, jd1008 wrote:
> On 09/25/2016 01:41 PM, Lawrence E Graves wrote:
> > On 09/25/2016 01:38 PM, jd1008 wrote:
> > > On 09/25/2016 01:14 PM, Lawrence E Graves wrote:
> > > > On 09/25/2016 01:01 PM, jd1008 wrote:
> > > > > On 09/25/2016 12:50 PM, Lawrence E Graves wrote:
> > > > > > On 09/25/2016 12:45 PM, Ahmad Samir wrote:
> > > > > > > On 25 September 2016 at 18:06, Lawrence E Graves 
> > > > > > >  wrote:
> > > > > > >> This the results of what you just told me. Hope it makes sense 
> > > > > > >> to you.
> > > > > > >>
> > > > > > >> [root@Jehovah ~]# /usr/bin/liveusb-creator
> > > > > > >> file:///usr/lib64/qt5/qml/QtQuick/Controls/ComboBox.qml:560:5: 
> > > > > > >> QML Menu:
> > > > > > >> Binding loop detected for property "__selectedIndex"
> > > > > > >> QOpenGLShaderProgram: could not create shader program
> > > > > > >> QOpenGLShader: could not create shader
> > > > > > >> QOpenGLShader: could not create shader
> > > > > > >> shader compilation failed:
> > > > > > >>
> > > > > > >> QOpenGLShaderProgram::uniformLocation( matrix ): shader program 
> > > > > > >> is not
> > > > > > >> linked
> > > > > > >> QOpenGLShaderProgram::uniformLocation( opacity ): shader 
> > > > > > >> program is not
> > > > > > >> linked
> > > > > > >> QOpenGLShaderProgram: could not create shader program
> > > > > > >> QOpenGLShader: could not create shader
> > > > > > >> QOpenGLShader: could not create shader
> > > > > > >> shader compilation failed:""
> > > > > > >>
> > > > > > > A shot in the dark, try running it as user, not root:
> > > > > > > liveusb-creator_polkit
> > > > > > >
> > > > > > > this should show a polkit dialogue where you have to type your root
> > > > > > > password to authenticate.
> > > > > > > _______________________________________________
> > > > > > > users mailing list -- [e-mail]
> > > > > > > To unsubscribe send an email to [e-mail]
> > > > > > This is what happen when I did what you asked.
> > > > > >
> > > > > > file:///usr/lib64/qt5/qml/QtQuick/Controls/ComboBox.qml:560:5: 
> > > > > > QML Menu: Binding loop detected for property "__selectedIndex"
> > > > > > QOpenGLShaderProgram: could not create shader program
> > > > > > QOpenGLShader: could not create shader
> > > > > > QOpenGLShader: could not create shader
> > > > > > shader compilation failed:
> > > > > > ...
> > > > >
> > > > > When I run liveusb-creator as root:
> > > > >
> > > > > # liveusb-creator
> > > > > Qt: Session management error: None of the authentication protocols 
> > > > > specified are supported
> > > > > /org/freedesktop/UDisks2/block_devices/sdb
> > > > >
> > > > > and the GUI interface pops up
> > > > > and it works.
> > > > > _______________________________________________
> > > > > users mailing list -- [e-mail]
> > > > > To unsubscribe send an email to [e-mail]
> > > >
> > > > I get the same results. It doesn't make sense to me. I have never 
> > > > had any trouble with it before.
> > >
> > > I think the problem might be that liveusb-creator
> > > is trying to communicate with /bin/dbus-daemon
> > > and fails.
> > > _______________________________________________
> > > users mailing list -- [e-mail]
> > > To unsubscribe send an email to [e-mail]
> >
> > Is there a way to fix that or will I have to wait until they fix it 
> > with an update?
>
> I should have also asked: are you at liberty to say in more detail 
> what you want to put on the USB?
> For example, is it an iso file? a directory of software including the 
> boot sector, ...etc
> _______________________________________________
> users mailing list -- [e-mail]
> To unsubscribe send an email to [e-mail]

Yes, I was trying to load a usb drive with Fedora 25 Alpha to try it out.