I'm looking for a document scanner that works well with F9. Any suggestion?
Thanks.
Dave Feustel writes:
I'm looking for a document scanner that works well with F9. Any suggestion?
www.sane-project.org has a convenient list of compatible scanners.
I, personally, use the Cannon MF-4270. I had to hack some bugs out of sane's pixma driver, but once I did that, it worked fine. The fixes went upstream, they should be in the next version of sane, so until then you'll have to pull them out of CVS and temporarily build your own driver.
The MF-4270 is really a multifunction scanner/copier/printer/fax machine. AFAIK, there is no support for the printer part of it, in CUPS, but I don't need the printer+fax functionality. It works fine for me as a scanner+copier. Supports both the flatbed and the document feeder, for scanning.
On Wed, 05 Nov 2008 18:35:02 -0500 Sam Varshavchik mrsam@courier-mta.com wrote:
www.sane-project.org has a convenient list of compatible scanners.
Virtually all of which are for hardware that is no longer made, but you might find on e-bay :-(.
I keep looking for a scanner that goes on the network and will deposit scanned documents directly in a network share so it can be totally OS independent, but I haven't found any such beast.
The commercial (but reasonably priced) vuescan software (from http://www.hamrick.com/) supports a much wider variety of actually available hardware, but only operates as a GUI, and I really like the ability to script things with the sane command line tools, so I haven't actually tried vuescan (but may someday get desperate enough to use the X11 XTEST extension to turn the vuescan GUI into a command line tool :-).
On Wed, 5 Nov 2008 19:36:30 -0500 Tom Horsley tom.horsley@att.net wrote:
On Wed, 05 Nov 2008 18:35:02 -0500 Sam Varshavchik mrsam@courier-mta.com wrote:
www.sane-project.org has a convenient list of compatible scanners.
Virtually all of which are for hardware that is no longer made, but you might find on e-bay :-(.
I keep looking for a scanner that goes on the network and will deposit scanned documents directly in a network share so it can be totally OS independent, but I haven't found any such beast.
Dell 3115cn is a scanner, printer, copier which speaks SMB and can also email you documents. It also does fax but that only works remotely in windows, while the rest works fine in Linux including the management web interface.
On Wed, Nov 05, 2008 at 06:35:02PM -0500, Sam Varshavchik wrote:
Dave Feustel writes:
I'm looking for a document scanner that works well with F9. Any suggestion?
www.sane-project.org has a convenient list of compatible scanners.
I, personally, use the Cannon MF-4270. I had to hack some bugs out of sane's pixma driver, but once I did that, it worked fine. The fixes went upstream, they should be in the next version of sane, so until then you'll have to pull them out of CVS and temporarily build your own driver.
The MF-4270 is really a multifunction scanner/copier/printer/fax machine. AFAIK, there is no support for the printer part of it, in CUPS, but I don't need the printer+fax functionality. It works fine for me as a scanner+copier. Supports both the flatbed and the document feeder, for scanning.
Thanks for the link! What kind of SCSI adaptor is needed for these scanners? Is OCR any good with them yet?
Sam Varshavchik wrote, On 11/05/2008 06:35 PM:
I, personally, use the Cannon MF-4270. I had to hack some bugs out of sane's pixma driver, but once I did that, it worked fine. The fixes went upstream, they should be in the next version of sane, so until then you'll have to pull them out of CVS and temporarily build your own driver.
The MF-4270 is really a multifunction scanner/copier/printer/fax machine. AFAIK, there is no support for the printer part of it, in CUPS, but I don't need the printer+fax functionality. It works fine for me as a scanner+copier. Supports both the flatbed and the document feeder, for scanning.
The actual printer _device_ driver for CUPS is often gutenprint[1]. I have seen a far amount of traffic on the gutenprint list[2] where some folks are trying to support some of the cannon equipment. And as you don't seem to be adverse to working out of a dev repository, perhaps you might want to take a look and see if your multifunction device is already supported or if you could give them the few needed pointers to get it supported.
[1] http://gimp-print.sourceforge.net/
[2] https://lists.sourceforge.net/lists/listinfo/gimp-print-devel
On Thu, Nov 06, 2008 at 09:13:16AM -0500, Todd Denniston wrote:
Sam Varshavchik wrote, On 11/05/2008 06:35 PM:
I, personally, use the Cannon MF-4270. I had to hack some bugs out of sane's pixma driver, but once I did that, it worked fine. The fixes went upstream, they should be in the next version of sane, so until then you'll have to pull them out of CVS and temporarily build your own driver.
The MF-4270 is really a multifunction scanner/copier/printer/fax machine. AFAIK, there is no support for the printer part of it, in CUPS, but I don't need the printer+fax functionality. It works fine for me as a scanner+copier. Supports both the flatbed and the document feeder, for scanning.
The actual printer _device_ driver for CUPS is often gutenprint[1]. I have seen a far amount of traffic on the gutenprint list[2] where some folks are trying to support some of the cannon equipment. And as you don't seem to be adverse to working out of a dev repository, perhaps you might want to take a look and see if your multifunction device is already supported or if you could give them the few needed pointers to get it supported.
[1] http://gimp-print.sourceforge.net/
[2] https://lists.sourceforge.net/lists/listinfo/gimp-print-devel
I am the OP for this thread. I am looking for a high resolution document scanner only, (no printer, no copier (I have a laser printer already) functions) with a usb or scsi interface. Years ago I had an HP C2 scanner which worked very well but it was big and slow. Plus I only had windows drivers for it.
Dave Feustel wrote, On 11/06/2008 11:50 AM:
I am the OP for this thread. I am looking for a high resolution document scanner only, (no printer, no copier (I have a laser printer already) functions) with a usb or scsi interface. Years ago I had an HP C2 scanner which worked very well but it was big and slow. Plus I only had windows drivers for it.
Sorry for kind of hijacking your thread.
To kind of get back on subject, I think for most of us you would need to define what you mean by: "high resolution document scanner". The reason you need to define it is that for me, scanning text (~8-12 point Helvetica|Arial|TimesNewRoman|Palatino) anything at or over 150DPI is going to be considered "high resolution", which almost every scanner today can do. If on the other hand you were scanning the dead sea scrolls (granted scanning with the light sources that scanners today use would probably destroy them), no one would be happy if you did not scan at > 3600DPI.
What kind of resolution did the C2 have?
The best luck I have had with picking out scanners is, go to http://www.sane-project.org/cgi-bin/driver.pl pick a bus you like http://www.sane-project.org/cgi-bin/driver.pl?manu=&model=&bus=usb&a... and look at the "Status" column and find manufacturers that seem to have a large percentage of their products that are listed as "complete" and "good". These manufactures have been either feeding the developers data on how to talk to their devices, or have been keeping a reasonably stable interface to the device, so even if none of the listed devices are currently available for new purchase they have a reasonable _likelihood_ of working especially if the new device is in the same "family".
Dave Feustel wrote:
On Thu, Nov 06, 2008 at 09:13:16AM -0500, Todd Denniston wrote:
Sam Varshavchik wrote, On 11/05/2008 06:35 PM:
[1] http://gimp-print.sourceforge.net/
[2] https://lists.sourceforge.net/lists/listinfo/gimp-print-devel
I am the OP for this thread. I am looking for a high resolution document scanner only, (no printer, no copier (I have a laser printer already) functions) with a usb or scsi interface. Years ago I had an HP C2 scanner which worked very well but it was big and slow. Plus I only had windows drivers for it.
We have an Epson V750 scanner that has been used on Ubuntu. It is nice for print, pictures and transparencies.
There is a driver that can be downloaded from the net.
Todd Denniston writes:
Sam Varshavchik wrote, On 11/05/2008 06:35 PM:
I, personally, use the Cannon MF-4270. I had to hack some bugs out of sane's pixma driver, but once I did that, it worked fine. The fixes went upstream, they should be in the next version of sane, so until then you'll have to pull them out of CVS and temporarily build your own driver.
The MF-4270 is really a multifunction scanner/copier/printer/fax machine. AFAIK, there is no support for the printer part of it, in CUPS, but I don't need the printer+fax functionality. It works fine for me as a scanner+copier. Supports both the flatbed and the document feeder, for scanning.
The actual printer _device_ driver for CUPS is often gutenprint[1].
I already have gutenprint installed. I'm not sure how gutenprint is supposed to interface with CUPS, but when I try to select the printer, this Canon model is not listed.
I have seen a far amount of traffic on the gutenprint list[2] where some folks are trying to support some of the cannon equipment. And as you don't seem to be adverse to working out of a dev repository, perhaps you might want to take a look and see if your multifunction device is already supported or if you could give them the few needed pointers to get it supported.
Well, I still don't see this Canon model listed as supported in the documentation in the latest, a fairly recent, release.
The only reason I could hack sane is because its supported for the scanner was already there, it just had some bugs. A complete absence of support for the entire printer is quite a different beast.
Sam Varshavchik wrote, On 11/06/2008 06:29 PM:
Todd Denniston writes:
<SNIP>
The actual printer _device_ driver for CUPS is often gutenprint[1].
I already have gutenprint installed. I'm not sure how gutenprint is supposed to interface with CUPS, but when I try to select the printer, this Canon model is not listed.
Often times the driver is supported by a similar models driver so you could either pick one that seems similar and try it, or you could ask on the list https://lists.sourceforge.net/lists/listinfo/gimp-print-devel
<SNIP>
Well, I still don't see this Canon model listed as supported in the documentation in the latest, a fairly recent, release.
Although you are correct in that gutenprint does not seem to support the device... <go rummaging for Linux printer information> ... http://www.linuxfoundation.org/en/OpenPrinting indicates: http://www.openprinting.org/show_printer.cgi?recnum=Canon-MF4270 there is a binary driver for it on one of canon's websites
Sorry to confuse you, by trying to lead you towards getting an Open Source driver going.
The only reason I could hack sane is because its supported for the scanner was already there, it just had some bugs. A complete absence of support for the entire printer is quite a different beast.
again, printer families often use the same or similar control protocol, and a similar driver might at least 'work' but not give nice results, and knowing that would help the devs know what they would need to change. however for this device there is a working (closed source) solution from the manufacturer, at least until Fedora upgrades to a point where it can't find a old library.
It is too bad so few folks know about the nice databases that have been put together for devices that work with Unix: http://www.linuxfoundation.org/en/OpenPrinting/Database/DatabaseIntro http://www.openprinting.org/printer_list.cgi http://www.sane-project.org/sane-supported-devices.html http://www.sane-project.org/cgi-bin/driver.pl
On Thu, 2008-11-06 at 21:06 -0500, Todd Denniston wrote:
Sam Varshavchik wrote, On 11/06/2008 06:29 PM:
Todd Denniston writes:
<SNIP> >> The actual printer _device_ driver for CUPS is often gutenprint[1]. > > I already have gutenprint installed. I'm not sure how gutenprint is > supposed to interface with CUPS, but when I try to select the printer, > this Canon model is not listed. >
Often times the driver is supported by a similar models driver so you could either pick one that seems similar and try it, or you could ask on the list https://lists.sourceforge.net/lists/listinfo/gimp-print-devel
<SNIP> > > Well, I still don't see this Canon model listed as supported in the > documentation in the latest, a fairly recent, release. Although you are correct in that gutenprint does not seem to support the device... <go rummaging for Linux printer information> ... http://www.linuxfoundation.org/en/OpenPrinting indicates: http://www.openprinting.org/show_printer.cgi?recnum=Canon-MF4270 there is a binary driver for it on one of canon's websites
Sorry to confuse you, by trying to lead you towards getting an Open Source driver going.
The only reason I could hack sane is because its supported for the scanner was already there, it just had some bugs. A complete absence of support for the entire printer is quite a different beast.
again, printer families often use the same or similar control protocol, and a similar driver might at least 'work' but not give nice results, and knowing that would help the devs know what they would need to change. however for this device there is a working (closed source) solution from the manufacturer, at least until Fedora upgrades to a point where it can't find a old library.
It is too bad so few folks know about the nice databases that have been put together for devices that work with Unix: http://www.linuxfoundation.org/en/OpenPrinting/Database/DatabaseIntro http://www.openprinting.org/printer_list.cgi http://www.sane-project.org/sane-supported-devices.html http://www.sane-project.org/cgi-bin/driver.pl
This is great information. I do not know if my question fits this thread or not, but, I have an issue where I have been able to install and access an HP parallel OfficeJet printer via the "root" sign on but I am not able to access the printer via a local user sign on. Any suggestions would be much appreciated.
thanks.
-- Todd Denniston Crane Division, Naval Surface Warfare Center (NSWC Crane) Harnessing the Power of Technology for the Warfighter
Jeff Maxwell wrote, On 11/07/2008 10:51 AM:
This is great information. I do not know if my question fits this thread or not, but,
It would probably be best to start another thread, with a fully new (not reply to this one) message.
I have an issue where I have been able to install and access an HP parallel OfficeJet printer via the "root" sign on but I am not able to access the printer via a local user sign on. Any suggestions would be much appreciated.
take a look in /var/log/cups/ at page_log, error_log and access_log and see if there is something that make sense there, before starting your new thread.
If there is no info there, then you may have to (backup first and) edit /etc/cups/cupsd.conf to set LogLevel to debug instead of info, then `service restart cups`. (hopefully a restorecon /etc/cups/cupsd.conf will not be needed) try a few prints and check the logs again.
On Fri, 2008-11-07 at 11:15 -0500, Todd Denniston wrote:
take a look in /var/log/cups/ at page_log, error_log and access_log and see if there is something that make sense there, before starting your new thread.
If there is no info there, then you may have to (backup first and) edit /etc/cups/cupsd.conf to set LogLevel to debug instead of info, then `service restart cups`. (hopefully a restorecon /etc/cups/cupsd.conf will not be needed) try a few prints and check the logs again.
It would be much easier to just run the printing troubleshooter, System->Administration->Printing, then Help->Troubleshoot. It automates log capture and can even diagnose some simple problems. If it fails to identify the problem, you can see the diagnostic output including the relevant portions of the log files. If the diagnostic output is too cryptic to understand but you think there is a bug in the software, file a bug report about your problem and attach the troubleshoot.txt file.
Tim. */
On Fri, 2008-11-07 at 11:15 -0500, Todd Denniston wrote:
Jeff Maxwell wrote, On 11/07/2008 10:51 AM:
This is great information. I do not know if my question fits this thread or not, but,
It would probably be best to start another thread, with a fully new (not reply to this one) message.
I have an issue where I have been able to install and access an HP parallel OfficeJet printer via the "root" sign on but I am not able to access the printer via a local user sign on. Any suggestions would be much appreciated.
take a look in /var/log/cups/ at page_log, error_log and access_log and see if there is something that make sense there, before starting your new thread.
If there is no info there, then you may have to (backup first and) edit /etc/cups/cupsd.conf to set LogLevel to debug instead of info, then `service restart cups`. (hopefully a restorecon /etc/cups/cupsd.conf will not be needed) try a few prints and check the logs again.
Thanks for the advice. I've been busy with other issues and finally found time to look further into this.
I did find the following in the cupsd.conf and I am wondering if the SystemGroup is causing my problem as I appear to be able to access my printer/scanner when logged in as "root" but not as a local user.
MaxLogSize 0 LogLevel info SystemGroup sys root
Thoughts?
-- Todd Denniston Crane Division, Naval Surface Warfare Center (NSWC Crane) Harnessing the Power of Technology for the Warfighter
On Tue, 2008-11-25 at 20:56 -0500, Jeff Maxwell wrote:
I did find the following in the cupsd.conf and I am wondering if the SystemGroup is causing my problem as I appear to be able to access my printer/scanner when logged in as "root" but not as a local user.
MaxLogSize 0 LogLevel info SystemGroup sys root
I should hope not. That allows you to define who's a system user who's allowed to configure things. Compared to the rest of the users who're just allowed to use them.
On Wed, 2008-11-26 at 12:41 +1030, Tim wrote:
On Tue, 2008-11-25 at 20:56 -0500, Jeff Maxwell wrote:
I did find the following in the cupsd.conf and I am wondering if the SystemGroup is causing my problem as I appear to be able to access my printer/scanner when logged in as "root" but not as a local user.
MaxLogSize 0 LogLevel info SystemGroup sys root
I should hope not. That allows you to define who's a system user who's allowed to configure things. Compared to the rest of the users who're just allowed to use them.
Well I am very confused. I decided to delete all printer definitions and start from scratch using the cups web administration process to add a printer. Once added, I went to the HP Device Manager and it had an icon for the printer but said that it could not be connected. I then switched users to "root" and using the HP device Manager it showed the printer connected with icons for options to scan, print or fax. One thing that I did find peculiar is that it asked for a user id/password when adding the printer. I tried to use my local user id/password but it would not accept it. It seemed to be in a loop and kept popping up asking for user id /password. I finally entered root and password which it accepted.
-- [tim@localhost ~]$ uname -r 2.6.27.5-41.fc9.i686
Don't send private replies to my address, the mailbox is ignored. I read messages from the public lists.
On Tue, 2008-11-25 at 21:32 -0500, Jeff Maxwell wrote:
On Wed, 2008-11-26 at 12:41 +1030, Tim wrote:
On Tue, 2008-11-25 at 20:56 -0500, Jeff Maxwell wrote:
I did find the following in the cupsd.conf and I am wondering if the SystemGroup is causing my problem as I appear to be able to access my printer/scanner when logged in as "root" but not as a local user.
MaxLogSize 0 LogLevel info SystemGroup sys root
I should hope not. That allows you to define who's a system user who's allowed to configure things. Compared to the rest of the users who're just allowed to use them.
Well I am very confused. I decided to delete all printer definitions and start from scratch using the cups web administration process to add a printer. Once added, I went to the HP Device Manager and it had an icon for the printer but said that it could not be connected. I then switched users to "root" and using the HP device Manager it showed the printer connected with icons for options to scan, print or fax. One thing that I did find peculiar is that it asked for a user id/password when adding the printer. I tried to use my local user id/password but it would not accept it. It seemed to be in a loop and kept popping up asking for user id /password. I finally entered root and password which it accepted.
It is standard to need to login with root and root passwd to be able to add a printer.
-- [tim@localhost ~]$ uname -r 2.6.27.5-41.fc9.i686
Don't send private replies to my address, the mailbox is ignored. I read messages from the public lists.
-- ======================================================================= Has anyone ever tasted an "end"? Are they really bitter? ======================================================================= Aaron Konstam telephone: (210) 656-0355 e-mail: akonstam@sbcglobal.net
On Wed, 2008-11-26 at 09:13 -0600, Aaron Konstam wrote:
On Tue, 2008-11-25 at 21:32 -0500, Jeff Maxwell wrote:
On Wed, 2008-11-26 at 12:41 +1030, Tim wrote:
On Tue, 2008-11-25 at 20:56 -0500, Jeff Maxwell wrote:
I did find the following in the cupsd.conf and I am wondering if the SystemGroup is causing my problem as I appear to be able to access my printer/scanner when logged in as "root" but not as a local user.
MaxLogSize 0 LogLevel info SystemGroup sys root
I should hope not. That allows you to define who's a system user who's allowed to configure things. Compared to the rest of the users who're just allowed to use them.
Well I am very confused. I decided to delete all printer definitions and start from scratch using the cups web administration process to add a printer. Once added, I went to the HP Device Manager and it had an icon for the printer but said that it could not be connected. I then switched users to "root" and using the HP device Manager it showed the printer connected with icons for options to scan, print or fax. One thing that I did find peculiar is that it asked for a user id/password when adding the printer. I tried to use my local user id/password but it would not accept it. It seemed to be in a loop and kept popping up asking for user id /password. I finally entered root and password which it accepted.
It is standard to need to login with root and root passwd to be able to add a printer.
Ok. I can understand the reasoning for that. But, why would I only have access to the printer/scanner when signed on as root and not as a local user? This is the problem that I am running into. Every time I wish to use the scanner, I need to switch users to root.
-- [tim@localhost ~]$ uname -r 2.6.27.5-41.fc9.i686
Don't send private replies to my address, the mailbox is ignored. I read messages from the public lists.
--
Has anyone ever tasted an "end"? Are they really bitter?
Aaron Konstam telephone: (210) 656-0355 e-mail: akonstam@sbcglobal.net
On Wed, 2008-11-26 at 16:14 -0500, Jeff Maxwell wrote:
On Wed, 2008-11-26 at 09:13 -0600, Aaron Konstam wrote:
On Tue, 2008-11-25 at 21:32 -0500, Jeff Maxwell wrote:
On Wed, 2008-11-26 at 12:41 +1030, Tim wrote:
On Tue, 2008-11-25 at 20:56 -0500, Jeff Maxwell wrote:
I did find the following in the cupsd.conf and I am wondering if the SystemGroup is causing my problem as I appear to be able to access my printer/scanner when logged in as "root" but not as a local user.
MaxLogSize 0 LogLevel info SystemGroup sys root
I should hope not. That allows you to define who's a system user who's allowed to configure things. Compared to the rest of the users who're just allowed to use them.
Well I am very confused. I decided to delete all printer definitions and start from scratch using the cups web administration process to add a printer. Once added, I went to the HP Device Manager and it had an icon for the printer but said that it could not be connected. I then switched users to "root" and using the HP device Manager it showed the printer connected with icons for options to scan, print or fax. One thing that I did find peculiar is that it asked for a user id/password when adding the printer. I tried to use my local user id/password but it would not accept it. It seemed to be in a loop and kept popping up asking for user id /password. I finally entered root and password which it accepted.
It is standard to need to login with root and root passwd to be able to add a printer.
Ok. I can understand the reasoning for that. But, why would I only have access to the printer/scanner when signed on as root and not as a local user? This is the problem that I am running into. Every time I wish to use the scanner, I need to switch users to root.
Well I would guess it is an incorrectly configured /etc/cups/cupsd.conf file. If you search that file you will find there are number of clauses that set policies and restrictions on users. So I would: 1. Look at the documentation for this file accessible through the cups interface. 2. Search the file for the word root and user.
root should appear only once in the SystemmGroup line. user appears in the various policies and restriction clauses.. These must be checked to change your restricted situation. -- ======================================================================= Walk softly and carry a megawatt laser. ======================================================================= Aaron Konstam telephone: (210) 656-0355 e-mail: akonstam@sbcglobal.net
Jeff Maxwell wrote, On 11/26/2008 04:14 PM:
Ok. I can understand the reasoning for that. But, why would I only have access to the printer/scanner when signed on as root and not as a local user? This is the problem that I am running into. Every time I wish to use the scanner, I need to switch users to root.
Jeff, try Tim Waugh's suggestion (I think he is taking you through the gnome menue to the troubleshooter): "System->Administration->Printing, then Help->Troubleshoot. It automates log capture and can even diagnose some simple problems. If it fails to identify the problem, you can see the diagnostic output including the relevant portions of the log files. If the diagnostic output is too cryptic to understand but you think there is a bug in the software, file a bug report about your problem and attach the troubleshoot.txt file."
If the menus don't get you the application, I think you could run system-config-printer in a terminal, and then select Help->Troubleshoot to get where Tim was pointing.
However I am expecting you to need to look at /var/log/cups/ files access_log & error_log to figure this out, ... because it WORKS as ROOT but not as NONROOT users. But do try the Troubleshoot first, as it might just cover this case, and if it does not then file the bug Tim mentioned and file another one against the system-config-printer Help->Troubleshoot to cover your case (so future folks might figure it out easier.
On Fri, 2008-11-07 at 10:51 -0500, Jeff Maxwell wrote:
This is great information. I do not know if my question fits this thread or not, but, I have an issue where I have been able to install and access an HP parallel OfficeJet printer via the "root" sign on but I am not able to access the printer via a local user sign on. Any suggestions would be much appreciated.
thanks.
--
When you go to web address: localhost:631 as a normal user do you see any Printers under the Printers tab? I assume you see them as root when you go to the same address. -- ======================================================================= Perfect day for scrubbing the floor and other exciting things. ======================================================================= Aaron Konstam telephone: (210) 656-0355 e-mail: akonstam@sbcglobal.net
On Fri, 2008-11-07 at 15:23 -0600, Aaron Konstam wrote:
On Fri, 2008-11-07 at 10:51 -0500, Jeff Maxwell wrote:
This is great information. I do not know if my question fits this thread or not, but, I have an issue where I have been able to install and access an HP parallel OfficeJet printer via the "root" sign on but I am not able to access the printer via a local user sign on. Any suggestions would be much appreciated.
thanks.
--
When you go to web address: localhost:631 as a normal user do you see any Printers under the Printers tab? I assume you see them as root when you go to the same address. --
When I go to Administration/printing, I have 2 printers listed under Local Printers.
They are: OfficeJet-Series-600 and OfficeJet_600.
OfficeJet-Series-600 has listed under the Settings Tab/Device URI: parallel:/dev/lp0
The other has hp:/par/OfficeJet_Series_600?device=/dev/parport0
Thanks.
======================================================================= Perfect day for scrubbing the floor and other exciting things. ======================================================================= Aaron Konstam telephone: (210) 656-0355 e-mail: akonstam@sbcglobal.net
On Wed, Nov 5, 2008 at 5:18 PM, Dave Feustel dfeustel@mindspring.comwrote:
I'm looking for a document scanner that works well with F9. Any suggestion?
Thanks.
-- fedora-list mailing list fedora-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list Guidelines: http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
One detail you left out of you question... What kind of scan quality are you looking for? If a multi-function printer/scanner/copier is good enough, check out hplip[1] and see which printers have scanner functionality working. I ran across the Photosmart C5580 when can be had for $99 at www.newegg.com[2] and most of the functions work line printing, scanning, even the flash card reader (however, no PC initiated fax, copy, or color calibration).
[1] http://hplipopensource.com/hplip-web/models/photosmart/photosmart_c5500_seri... [2] http://www.newegg.com/Product/Product.aspx?Item=N82E16828115252&Tpk=c558...
Richard
Dave Feustel wrote:
I'm looking for a document scanner that works well with F9. Any suggestion?
Thanks.
Epson CX7400 printer and scanner work with FC6, using the driver from the vendor. As of FC8 or early FC9 the driver wasn't updated. Since I can keep FC6 running safely behind a firewall, as a device controller, I can live with that, although I would like to upgrade o/s at some point.
Bill Davidsen wrote, On 11/15/2008 09:35 PM:
Dave Feustel wrote:
I'm looking for a document scanner that works well with F9. Any suggestion?
Thanks.
Epson CX7400 printer and scanner work with FC6, using the driver from the vendor. As of FC8 or early FC9 the driver wasn't updated. Since I can keep FC6 running safely behind a firewall, as a device controller, I can live with that, although I would like to upgrade o/s at some point.
http://www.openprinting.org/show_printer.cgi?recnum=Epson-Stylus_CX7400 http://www.sane-project.org/cgi-bin/driver.pl?manu=epson&model=cx7400&am...
looks like you need: gutenprint 5.something sane epkowa 2.12.0
not sure which versions are in F10 but it looks like at least the printing functions may be supported in F9, and I have never investigated how hard it is to use an updated sane back-end with fedora.
BTW there are nice databases that have been put together for devices that work with Unix: http://www.linuxfoundation.org/en/OpenPrinting/Database/DatabaseIntro http://www.openprinting.org/printer_list.cgi http://www.sane-project.org/sane-supported-devices.html http://www.sane-project.org/cgi-bin/driver.pl
-
Aaron Konstam -
Alan Cox -
Bill Davidsen -
Dave Feustel -
Jeff Maxwell -
Richard Shaw -
Robin Laing -
Sam Varshavchik -
Tim -
Tim Waugh -
Todd Denniston -
Tom Horsley