All,
I am running FC6 (with latest update, 64-bit) on AMD Dual Core with 1GB RAM. It contains a SATA hard disk. I am experience sluggishness when files are opened or closed (saved). I suspect that i have slow SATA performance even though i am not sure. I have following stats.
# hdparm -Tt /dev/sda
/dev/sda: Timing cached reads: 2452 MB in 2.00 seconds = 1226.48 MB/sec Timing buffered disk reads: 86 MB in 3.03 seconds = 28.35 MB/sec
I am concerned about 28.35 MB/Sec speed here.
# hdparm -i /dev/sda
/dev/sda: HDIO_GET_IDENTITY failed: Inappropriate ioctl for device
# dmesg | grep -i sata sata_nv 0000:00:0e.0: version 3.2 ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0xE000 irq 21 ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE082 bmdma 0xE008 irq 21 scsi0 : sata_nv ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300)
# lsmod | grep -i sata sata_nv 29509 4 libata 120553 1 sata_nv
Kernel Boot Parameter kernel /vmlinuz-2.6.20-1.2933.fc6 ro root=LABEL=/1 noquiet combined_mode=libata
Any suggestions/recommendations/comments are welcome.
Thanks
Srikanth
Srikanth Konjarla wrote:
All,
I am running FC6 (with latest update, 64-bit) on AMD Dual Core with 1GB RAM. It contains a SATA hard disk. I am experience sluggishness when files are opened or closed (saved). I suspect that i have slow SATA performance even though i am not sure. I have following stats.
# hdparm -Tt /dev/sda
/dev/sda: Timing cached reads: 2452 MB in 2.00 seconds = 1226.48 MB/sec Timing buffered disk reads: 86 MB in 3.03 seconds = 28.35 MB/sec
I am concerned about 28.35 MB/Sec speed here.
# hdparm -i /dev/sda
/dev/sda: HDIO_GET_IDENTITY failed: Inappropriate ioctl for device
# dmesg | grep -i sata sata_nv 0000:00:0e.0: version 3.2 ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0xE000 irq 21 ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE082 bmdma 0xE008 irq 21 scsi0 : sata_nv ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300)
# lsmod | grep -i sata sata_nv 29509 4 libata 120553 1 sata_nv
Kernel Boot Parameter kernel /vmlinuz-2.6.20-1.2933.fc6 ro root=LABEL=/1 noquiet combined_mode=libata
Any suggestions/recommendations/comments are welcome.
Thanks
Srikanth
You may want to check for other activity on the system. I normally try to do a couple of tests at different times to see if they are the same. Just after a system is booted is probably the worst time to check.
From the hdparm man page:
For meaningful results, this operation should be repeated 2-3 times on an otherwise inactive system (no other active processes) with at least a couple of megabytes of free memory.
Mikkel
Mikkel L. Ellertson wrote:
Srikanth Konjarla wrote:
All,
I am running FC6 (with latest update, 64-bit) on AMD Dual Core with 1GB RAM. It contains a SATA hard disk. I am experience sluggishness when files are opened or closed (saved). I suspect that i have slow SATA performance even though i am not sure. I have following stats.
# hdparm -Tt /dev/sda
/dev/sda: Timing cached reads: 2452 MB in 2.00 seconds = 1226.48 MB/sec Timing buffered disk reads: 86 MB in 3.03 seconds = 28.35 MB/sec
I am concerned about 28.35 MB/Sec speed here.
# hdparm -i /dev/sda
/dev/sda: HDIO_GET_IDENTITY failed: Inappropriate ioctl for device
# dmesg | grep -i sata sata_nv 0000:00:0e.0: version 3.2 ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0xE000 irq 21 ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE082 bmdma 0xE008 irq 21 scsi0 : sata_nv ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300)
# lsmod | grep -i sata sata_nv 29509 4 libata 120553 1 sata_nv
Kernel Boot Parameter kernel /vmlinuz-2.6.20-1.2933.fc6 ro root=LABEL=/1 noquiet combined_mode=libata
Any suggestions/recommendations/comments are welcome.
Thanks
Srikanth
You may want to check for other activity on the system. I normally try to do a couple of tests at different times to see if they are the same. Just after a system is booted is probably the worst time to check.
From the hdparm man page:
For meaningful results, this operation should be repeated 2-3 times on an otherwise inactive system (no other active processes) with at least a couple of megabytes of free memory.
Thanks for the response. My tests qualify to those conditions.
Srikanth
Mikkel
-
Mikkel -
Srikanth Konjarla