I just tried burning a DVD (authored by DeVeDe) and both K3b and GnomeBaker fail to start writing. Clean boot doesn't help, neither does lowering the write speed to 4x. Anyone else having this problem?
kernel: 2.6.31.9-174.fc12.i686
dmesg: cdrom: This disc doesn't have any tracks I recognize! sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current] sr 1:0:0:0: [sr0] Add. Sense: Logical block address out of range end_request: I/O error, dev sr0, sector 0 Buffer I/O error on device sr0, logical block 0 ... warning: `growisofs' uses 32-bit capabilities (legacy support in use) ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata2.00: cmd a0/01:00:00:00:80/00:00:00:00:00/a0 tag 0 dma 32768 out cdb 2a 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 res 40/00:02:00:18:00/00:00:00:00:00/a0 Emask 0x4 (timeout) ata2.00: status: { DRDY } ata2: link is slow to respond, please be patient (ready=0) ata2: device not ready (errno=-16), forcing hardreset ata2: soft resetting link ata2.00: configured for UDMA/33 ata2: EH complete
Konstantin Svist wrote:
I just tried burning a DVD (authored by DeVeDe) and both K3b and GnomeBaker fail to start writing. Clean boot doesn't help, neither does lowering the write speed to 4x. Anyone else having this problem?
That's because the message says "device not ready" and no change in parameters will make it work until you address that. Bad media, bad cable, bad burner, I can't tell. It's likely to be hardware, but I don't normally use the frontends for the tools, so you may have made a mistake in starting the run.
kernel: 2.6.31.9-174.fc12.i686
dmesg: cdrom: This disc doesn't have any tracks I recognize! sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current] sr 1:0:0:0: [sr0] Add. Sense: Logical block address out of range end_request: I/O error, dev sr0, sector 0 Buffer I/O error on device sr0, logical block 0 ... warning: `growisofs' uses 32-bit capabilities (legacy support in use) ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata2.00: cmd a0/01:00:00:00:80/00:00:00:00:00/a0 tag 0 dma 32768 out cdb 2a 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 res 40/00:02:00:18:00/00:00:00:00:00/a0 Emask 0x4 (timeout) ata2.00: status: { DRDY } ata2: link is slow to respond, please be patient (ready=0) ata2: device not ready (errno=-16), forcing hardreset ata2: soft resetting link ata2.00: configured for UDMA/33 ata2: EH complete
On 12/31/2009 04:52 PM, Bill Davidsen wrote:
Konstantin Svist wrote:
I just tried burning a DVD (authored by DeVeDe) and both K3b and GnomeBaker fail to start writing. Clean boot doesn't help, neither does lowering the write speed to 4x. Anyone else having this problem?
That's because the message says "device not ready" and no change in parameters will make it work until you address that. Bad media, bad cable, bad burner, I can't tell. It's likely to be hardware, but I don't normally use the frontends for the tools, so you may have made a mistake in starting the run.
Not at all, CDs burn just fine. It's only the DVDs that don't burn. I've seen a similar problem many times with fresh kernels. It comes and goes.. and annoys the hell out of me.
-
Bill Davidsen -
Konstantin Svist