5:23 p.m.
Hello, Ankush
Even before I sent my last message to this list, I was completely up to date.
I am running the latest stable kernel update: kernel-2.6.10-1.760_FC3
I am also running the latest stable update of hotplug: hotplug-2004_04_01-8.1
As I mentioned, I was running both of these when I sent my last message.
Also, my problem is that my devices dissappear, not that they are not
detected. If I unplug a device that has "dissappeared" and plug it into a
different USB2 port, it is immediately detected. Also, if I unplug a device
and plug it back into the same port (I've only tried that after waiting a few
minutes), the device magically reappears. I can't remember though if the
device is actually functional. Also, I am now running a PCI USB2 card, and
I've been using the burner successfully ever since. I just tried to use our
scanner while it was plugged into that PCI USB2 card, and I ended up having
to reboot about five times. When I plugged it back into one of the front
USB2 ports on our machine (this port is connected directly to the mainboard
instead of being a PCI card) the strangest thing happened: I could finally
scan without the scanner hanging. I hate to do it, but I think I will take
the scanner to a machine that I have access to that runs Windows XP. I will
see how it behaves...
If there is a development or testing kernel or hotplug RPM that you think I
should try, please let me know.
Again, our devices get detected and re-detected just fine, the problem is that
they just dissappear....
Steven P. Ulrick
Just to throw my 2 cents into this discussion.
I installed FC3 kernel 2.6.10-1.741 onto my gateway 7200x system.
When i plugged in my usb braille display, it sometimes detects and other times it
doesn't.
I ran yum to get fully up to date, and still have the problem.
I just unplugged and re-plugged the display into one of the usb ports on the back of the
pc, the /var/logs/messages file shows the following info:
Feb 16 09:08:02 oasis brltty[623]: USB URB status error 84: Invalid or incomplete
multibyte or wide character.
Feb 16 09:08:02 oasis brltty[623]: USB configuration set error 71: Protocol error.
Feb 16 09:08:02 oasis kernel: usb 2-1: USB disconnect, address 38
Feb 16 09:08:02 oasis kernel: usb 2-1.1: USB disconnect, address 39
Feb 16 09:08:07 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 40
Feb 16 09:08:07 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:07 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:08 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 41
Feb 16 09:08:10 oasis kernel: usb 2-1: USB disconnect, address 40
Feb 16 09:08:10 oasis kernel: usb 2-1.1: USB disconnect, address 41
Feb 16 09:08:10 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 42
Feb 16 09:08:10 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:10 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:11 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 43
Feb 16 09:08:11 oasis kernel: usb 2-1.1: config index 0 descriptor too short (expected 32,
got 8)
Feb 16 09:08:11 oasis kernel: usb 2-1.1: config 1 has 0 interfaces, different from the
descriptor's value: 1
Feb 16 09:08:12 oasis brltty[623]: USB interface claim error 2: No such file or
directory.
Feb 16 09:08:17 oasis brltty[623]: USB interface claim error 2: No such file or
directory.
Feb 16 09:08:18 oasis kernel: usb 2-1: USB disconnect, address 42
Feb 16 09:08:18 oasis kernel: usb 2-1.1: USB disconnect, address 43
Feb 16 09:08:20 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 44
Feb 16 09:08:20 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:20 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:21 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 45
Feb 16 09:08:23 oasis brltty[623]: Alva driver, version 2.2
my /proc/bus/usb/device file contains the following info:
T: Bus=02 Lev=02 Prnt=44 Port=00 Cnt=01 Dev#= 45 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=06b0 ProdID=0001 Rev=20.02
S: Manufacturer=ALVA B.V.
S: Product=ALVA 544 Satellite
S: SerialNumber=54400015
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbfs
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=20ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 8 Ivl=0ms
As a side note, I have greater success if iI disable haldaemon.
--
This is an email sent via the webforum on http://fcp.homelinux.org
10:10 p.m.
New subject: usb storage devices
hey,
did you update usbutilits and udev rpms also.For the problem you are
facing i will definitely look for some solution.
Regards
Ankush
On Thu, 17 Feb 2005 00:23:09 +0100, Donald Raikes (draikes)
<no-reply-gw(a)fcp.homelinux.org> wrote:
Hello, Ankush
Even before I sent my last message to this list, I was completely up to date.
I am running the latest stable kernel update: kernel-2.6.10-1.760_FC3
I am also running the latest stable update of hotplug: hotplug-2004_04_01-8.1
As I mentioned, I was running both of these when I sent my last message.
Also, my problem is that my devices dissappear, not that they are not
detected. If I unplug a device that has "dissappeared" and plug it into a
different USB2 port, it is immediately detected. Also, if I unplug a device
and plug it back into the same port (I've only tried that after waiting a few
minutes), the device magically reappears. I can't remember though if the
device is actually functional. Also, I am now running a PCI USB2 card, and
I've been using the burner successfully ever since. I just tried to use our
scanner while it was plugged into that PCI USB2 card, and I ended up having
to reboot about five times. When I plugged it back into one of the front
USB2 ports on our machine (this port is connected directly to the mainboard
instead of being a PCI card) the strangest thing happened: I could finally
scan without the scanner hanging. I hate to do it, but I think I will take
the scanner to a machine that I have access to that runs Windows XP. I will
see how it behaves...
If there is a development or testing kernel or hotplug RPM that you think I
should try, please let me know.
Again, our devices get detected and re-detected just fine, the problem is that
they just dissappear....
Steven P. Ulrick
Just to throw my 2 cents into this discussion.
I installed FC3 kernel 2.6.10-1.741 onto my gateway 7200x system.
When i plugged in my usb braille display, it sometimes detects and other times it
doesn't.
I ran yum to get fully up to date, and still have the problem.
I just unplugged and re-plugged the display into one of the usb ports on the back of the
pc, the /var/logs/messages file shows the following info:
Feb 16 09:08:02 oasis brltty[623]: USB URB status error 84: Invalid or incomplete
multibyte or wide character.
Feb 16 09:08:02 oasis brltty[623]: USB configuration set error 71: Protocol error.
Feb 16 09:08:02 oasis kernel: usb 2-1: USB disconnect, address 38
Feb 16 09:08:02 oasis kernel: usb 2-1.1: USB disconnect, address 39
Feb 16 09:08:07 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 40
Feb 16 09:08:07 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:07 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:08 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 41
Feb 16 09:08:10 oasis kernel: usb 2-1: USB disconnect, address 40
Feb 16 09:08:10 oasis kernel: usb 2-1.1: USB disconnect, address 41
Feb 16 09:08:10 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 42
Feb 16 09:08:10 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:10 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:11 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 43
Feb 16 09:08:11 oasis kernel: usb 2-1.1: config index 0 descriptor too short (expected
32, got 8)
Feb 16 09:08:11 oasis kernel: usb 2-1.1: config 1 has 0 interfaces, different from the
descriptor's value: 1
Feb 16 09:08:12 oasis brltty[623]: USB interface claim error 2: No such file or
directory.
Feb 16 09:08:17 oasis brltty[623]: USB interface claim error 2: No such file or
directory.
Feb 16 09:08:18 oasis kernel: usb 2-1: USB disconnect, address 42
Feb 16 09:08:18 oasis kernel: usb 2-1.1: USB disconnect, address 43
Feb 16 09:08:20 oasis kernel: usb 2-1: new full speed USB device using uhci_hcd and
address 44
Feb 16 09:08:20 oasis kernel: hub 2-1:1.0: USB hub found
Feb 16 09:08:20 oasis kernel: hub 2-1:1.0: 3 ports detected
Feb 16 09:08:21 oasis kernel: usb 2-1.1: new full speed USB device using uhci_hcd and
address 45
Feb 16 09:08:23 oasis brltty[623]: Alva driver, version 2.2
my /proc/bus/usb/device file contains the following info:
T: Bus=02 Lev=02 Prnt=44 Port=00 Cnt=01 Dev#= 45 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=06b0 ProdID=0001 Rev=20.02
S: Manufacturer=ALVA B.V.
S: Product=ALVA 544 Satellite
S: SerialNumber=54400015
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=00(>ifc ) Sub=00 Prot=00 Driver=usbfs
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=20ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 8 Ivl=0ms
As a side note, I have greater success if iI disable haldaemon.
--
This is an email sent via the webforum on http://fcp.homelinux.org
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
12:10 a.m.
New subject: usb storage devices
On Wednesday 16 February 2005 10:10 pm, Ankush Grover wrote:
hey,
did you update usbutilits and udev rpms also.For the problem you are
facing i will definitely look for some solution.
Regards
Ankush
Hello, Donald :)
I had EXACTLY the same thing happen to me. Anksuh advised me to update those
items just like he suggested to you. Like you, I had all the stable updates
installed. But, I had gotten so tired of rebooting to get rid of zombie
processes, and get full functionality back on our USB2 devices, that I
thought I would update those RPM's from Rawhide. Guess what? My devices
have not dissappeared since! All is now well here :)
I even tried an experiment: I plugged our scanner into one of our six USB2
ports, and scanned a 600dpi image. No problem. I unplugged it and
IMMEDIATELY replugged it into another USB2 port and scanned the same image at
the same dpi. Again, success. I repeated this test four times, four
different ports, no problems. Most of the time my devices would dissappear,
but I also experienced functionality issues with our two devices. Now I have
even burned quite a few cd's over a week or so, and all is well!
I would update the RPM's (from Rawhide) that Ankush said to update. I will
tell you all of the ones that I updated, but try what he said first, and see
how things go:
I updated:
hotplug
usbutils
udev
kernel
initscripts (I thought I would update that as well, since I would be running
FC3 with a Rawhide kernel. Our system booted fine Without updating
initscripts, but on the other hand, it has been running beautifully ever
since, With initscripts from Rawhide. YMMV.)
Our uptime looks like this:
00:02:40 up 5 days, 16:57, 4 users, load average: 2.87, 2.40, 1.40
That is a big deal for me, because I had to reboot every time that full
functionality was not restored after plugging a device in a different port.
I did reboot everytime that a zombie process got started because of running a
command related to a device that had dissappeared, but of course, all of that
is in the past now.
Also, check out my message to this list on this same thread, that I sent after
everything started working perfectly again:
https://www.redhat.com/archives/fedora-list/2005-February/msg03565.html
Have a Great Day,
Steven P. Ulrick
6:20 p.m.
New subject: usb storage devices
I have another piece of this puzzle. From the GUI menu System:
Tools/Network Device Control, then click on "configure", the USB
devices are immediately detected.
I don't understand... but at least it works... now why won't my
printer work? Sorry... need a new thread.
On Thu, 17 Feb 2005 00:10:35 -0600, Steven P. Ulrick
<ulrick2(a)faith4miracle.org> wrote:
On Wednesday 16 February 2005 10:10 pm, Ankush Grover wrote:
> hey,
>
> did you update usbutilits and udev rpms also.For the problem you are
> facing i will definitely look for some solution.
>
> Regards
>
> Ankush
Hello, Donald :)
I had EXACTLY the same thing happen to me. Anksuh advised me to update those
items just like he suggested to you. Like you, I had all the stable updates
installed. But, I had gotten so tired of rebooting to get rid of zombie
processes, and get full functionality back on our USB2 devices, that I
thought I would update those RPM's from Rawhide. Guess what? My devices
have not dissappeared since! All is now well here :)
I even tried an experiment: I plugged our scanner into one of our six USB2
ports, and scanned a 600dpi image. No problem. I unplugged it and
IMMEDIATELY replugged it into another USB2 port and scanned the same image at
the same dpi. Again, success. I repeated this test four times, four
different ports, no problems. Most of the time my devices would dissappear,
but I also experienced functionality issues with our two devices. Now I have
even burned quite a few cd's over a week or so, and all is well!
I would update the RPM's (from Rawhide) that Ankush said to update. I will
tell you all of the ones that I updated, but try what he said first, and see
how things go:
I updated:
hotplug
usbutils
udev
kernel
initscripts (I thought I would update that as well, since I would be running
FC3 with a Rawhide kernel. Our system booted fine Without updating
initscripts, but on the other hand, it has been running beautifully ever
since, With initscripts from Rawhide. YMMV.)
Our uptime looks like this:
00:02:40 up 5 days, 16:57, 4 users, load average: 2.87, 2.40, 1.40
That is a big deal for me, because I had to reboot every time that full
functionality was not restored after plugging a device in a different port.
I did reboot everytime that a zombie process got started because of running a
command related to a device that had dissappeared, but of course, all of that
is in the past now.
Also, check out my message to this list on this same thread, that I sent after
everything started working perfectly again:
https://www.redhat.com/archives/fedora-list/2005-February/msg03565.html
Have a Great Day,
Steven P. Ulrick
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
7:29 p.m.
New subject: usb storage devices
Ican't imagine why your having a problem. I have since Red Hat 9 had
zero problems with USB ports or devices connected theron. I even have a
thing I got from Best Buy that stays connected and when I push in my
digital camera memory stick, it becomes just another hard drive to
Linux. I have Bluetooth and all the other stuff turned on and it works
fine in my Core 2.
Dale Raby wrote:
I have another piece of this puzzle. From the GUI menu System:
Tools/Network Device Control, then click on "configure", the USB
devices are immediately detected.
I don't understand... but at least it works... now why won't my
printer work? Sorry... need a new thread.
On Thu, 17 Feb 2005 00:10:35 -0600, Steven P. Ulrick
<ulrick2(a)faith4miracle.org> wrote:
>On Wednesday 16 February 2005 10:10 pm, Ankush Grover wrote:
>
>
>>hey,
>>
>>did you update usbutilits and udev rpms also.For the problem you are
>>facing i will definitely look for some solution.
>>
>>Regards
>>
>>Ankush
>>
>>
>Hello, Donald :)
>I had EXACTLY the same thing happen to me. Anksuh advised me to update those
>items just like he suggested to you. Like you, I had all the stable updates
>installed. But, I had gotten so tired of rebooting to get rid of zombie
>processes, and get full functionality back on our USB2 devices, that I
>thought I would update those RPM's from Rawhide. Guess what? My devices
>have not dissappeared since! All is now well here :)
>I even tried an experiment: I plugged our scanner into one of our six USB2
>ports, and scanned a 600dpi image. No problem. I unplugged it and
>IMMEDIATELY replugged it into another USB2 port and scanned the same image at
>the same dpi. Again, success. I repeated this test four times, four
>different ports, no problems. Most of the time my devices would dissappear,
>but I also experienced functionality issues with our two devices. Now I have
>even burned quite a few cd's over a week or so, and all is well!
>I would update the RPM's (from Rawhide) that Ankush said to update. I will
>tell you all of the ones that I updated, but try what he said first, and see
>how things go:
>I updated:
> hotplug
> usbutils
> udev
> kernel
> initscripts (I thought I would update that as well, since I would be running
>FC3 with a Rawhide kernel. Our system booted fine Without updating
>initscripts, but on the other hand, it has been running beautifully ever
>since, With initscripts from Rawhide. YMMV.)
>
>Our uptime looks like this:
> 00:02:40 up 5 days, 16:57, 4 users, load average: 2.87, 2.40, 1.40
>That is a big deal for me, because I had to reboot every time that full
>functionality was not restored after plugging a device in a different port.
>I did reboot everytime that a zombie process got started because of running a
>command related to a device that had dissappeared, but of course, all of that
>is in the past now.
>Also, check out my message to this list on this same thread, that I sent after
>everything started working perfectly again:
>https://www.redhat.com/archives/fedora-list/2005-February/msg03565.html
>
>Have a Great Day,
>Steven P. Ulrick
>
>--
>fedora-list mailing list
>fedora-list(a)redhat.com
>To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
>
>
>
6983
days inactive
7007
days old
4 comments
5 participants
participants (5)
-
Ankush Grover -
Dale A. Raby -
jery_wang -
Karl Larsen -
Steven P. Ulrick