2:04 p.m.
I am trying to install a Sprint Mobile Broadband USB Modem (Novatel Ovation U720) cellular
USB phone on a Dell laptop running FC7 test4. I found a variety of instructions on getting
it to work with FC6 and applied it to my install and it works..sort of.
I have the laptop set to dual boot with XP. I first made sure it worked under XP. It does
and it extremely fast. I then did the install on FC7. After issuing "/sbin/modprobe
usbserial vendor=0×1410 product=0×2110". Once that was done, the modem appeared as
/dev/ttyUSB0 and /dev/ttyUSB1 (someone said they think the latter is a management and
diagnostic interface; the former is used for the PPP connection). I was then able to use
KPPP to set up a dialer connection. I started the dialer and bam it connected. Once
connected I see this:
# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3249 errors:0 dropped:0 overruns:0 frame:0
TX packets:3249 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13067764 (12.4 MiB) TX bytes:13067764 (12.4 MiB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:xx.11.222.aa P-t-P:yy.28.249.bb Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:3850 errors:0 dropped:0 overruns:0 frame:0
TX packets:3463 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:3681723 (3.5 MiB) TX bytes:532348 (519.8 KiB)
The only problem is that it is slow as glue. When I click on a website, it takes 30 to 90
seconds to respond. Once it actually starts pulling data, it seems a little quicker but
then bogs down when trying to go to the next website. I manually changed the
"serial" bit rate in the configuration files to the same way it was set in XP
(230400 bps) but that did not help.
In XP, the IP is set as follows:
Connected to NDIS:
Intel(R) PRO/100 VE Network Connection - Packet Scheduler Miniport
GUID: TRUCK4FC-E323-407D-B802-9D7F4412345
MAC Address: 00-14-3F-F5-1F-CB
Type: Ethernet Adapter
IPAddresses: 0.0.0.0
Gateway Addresses:
DHCP Enabled.
Lease Obtained Sun Aug 06 23:28:58 2006
Lease Expires Sun Aug 06 23:28:58 2006
DHCP Server Addresses: 192.168.1.1
WINS Disabled.
WAN (PPP/SLIP) Interface
GUID: 1234FAEE-F7D6-49F8-A71E-E9666BB54321
MAC Address: 00-53-45-00-00-00
Type: PPP Adapter
IPAddresses: YY.243.236.BB
Gateway Addresses: YY.243.236.BB
DHCP Disabled.
WINS Disabled.
Does anyone have any ideas?
Arch
3:42 p.m.
Arch Willingham wrote:
I am trying to install a Sprint Mobile Broadband USB Modem (Novatel
Ovation U720) cellular USB phone on a Dell laptop running FC7 test4. I found a variety of
instructions on getting it to work with FC6 and applied it to my install and it
works..sort of.
I have the laptop set to dual boot with XP. I first made sure it worked under XP. It does
and it extremely fast. I then did the install on FC7. After issuing "/sbin/modprobe
usbserial vendor=0×1410 product=0×2110". Once that was done, the modem appeared as
/dev/ttyUSB0 and /dev/ttyUSB1 (someone said they think the latter is a management and
diagnostic interface; the former is used for the PPP connection). I was then able to use
KPPP to set up a dialer connection. I started the dialer and bam it connected. Once
connected I see this:
# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3249 errors:0 dropped:0 overruns:0 frame:0
TX packets:3249 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13067764 (12.4 MiB) TX bytes:13067764 (12.4 MiB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:xx.11.222.aa P-t-P:yy.28.249.bb Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:3850 errors:0 dropped:0 overruns:0 frame:0
TX packets:3463 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:3681723 (3.5 MiB) TX bytes:532348 (519.8 KiB)
The only problem is that it is slow as glue. When I click on a website, it takes 30 to 90
seconds to respond. Once it actually starts pulling data, it seems a little quicker but
then bogs down when trying to go to the next website. I manually changed the
"serial" bit rate in the configuration files to the same way it was set in XP
(230400 bps) but that did not help.
In XP, the IP is set as follows:
Connected to NDIS:
Intel(R) PRO/100 VE Network Connection - Packet Scheduler Miniport
GUID: TRUCK4FC-E323-407D-B802-9D7F4412345
MAC Address: 00-14-3F-F5-1F-CB
Type: Ethernet Adapter
IPAddresses: 0.0.0.0
Gateway Addresses:
DHCP Enabled.
Lease Obtained Sun Aug 06 23:28:58 2006
Lease Expires Sun Aug 06 23:28:58 2006
DHCP Server Addresses: 192.168.1.1
WINS Disabled.
WAN (PPP/SLIP) Interface
GUID: 1234FAEE-F7D6-49F8-A71E-E9666BB54321
MAC Address: 00-53-45-00-00-00
Type: PPP Adapter
IPAddresses: YY.243.236.BB
Gateway Addresses: YY.243.236.BB
DHCP Disabled.
WINS Disabled.
Does anyone have any ideas?
Arch
That is an IPV6 address.
Can we see your: /etc/wvdial.conf ?
It is usually a matter of the 'correct' initialize/dial strings.
4:08 p.m.
Would it be called something else? There is no /etc/wvdial.conf file on my system. Since I
was firing it off with kpp, here is the config file (I'm making a huge guess here):
/mycomputer/.kde/share/config/kppprc
pppdArguments=
[Account0]
AccountingEnabled=0
AccountingFile=
Authentication=4
AutoDNS=1
AutoName=0
BeforeConnect=
BeforeDisconnect=
CallbackPhone=
CallbackType=0
Command=
DNS=
DefaultRoute=1
DisconnectCommand=
Domain=
ExDNSDisabled=0
Gateway=0.0.0.0
IPAddr=0.0.0.0
Name=Sprint
Password=vzw
Phonenumber=#777
ScriptArguments=
ScriptCommands=
StorePassword=1
SubnetMask=0.0.0.0
Username=auburn(a)tigers.COM
VolumeAccountingEnabled=0
pppdArguments=
[General]
DefaultAccount=Sprint
DefaultModem=Sprint
NumberOfAccounts=1
NumberOfModems=1
PPPDebug=0
ShowLogWindow=1
[Graph]
Background=255,255,255
Enabled=true
InBytes=0,0,255
OutBytes=255,0,0
Text=0,0,0
[Modem0]
BusyWait=0
Device=/dev/ttyUSB0
Enter=CR
FlowControl=Hardware [CRTSCTS]
Name=Sprint
Speed=230400
Timeout=60
UseLockFile=1
Volume=1
WaitForDialTone=1
[WindowPosition]
WindowPositionConWinX=351
WindowPositionConWinY=328
WindowPositionStatWinX=326
WindowPositionStatWinY=175
Arch
-----Original Message-----
From: fedora-list-bounces(a)redhat.com
[mailto:fedora-list-bounces@redhat.com]On Behalf Of Phil Meyer
Sent: Thursday, May 24, 2007 4:43 PM
To: For users of Fedora
Subject: Re: Sprint Novatel Ovation U720 USB phone very slow on Fedora
Arch Willingham wrote:
I am trying to install a Sprint Mobile Broadband USB Modem (Novatel
Ovation U720) cellular USB phone on a Dell laptop running FC7 test4. I found a variety of
instructions on getting it to work with FC6 and applied it to my install and it
works..sort of.
I have the laptop set to dual boot with XP. I first made sure it worked under XP. It does
and it extremely fast. I then did the install on FC7. After issuing "/sbin/modprobe
usbserial vendor=0×1410 product=0×2110". Once that was done, the modem appeared as
/dev/ttyUSB0 and /dev/ttyUSB1 (someone said they think the latter is a management and
diagnostic interface; the former is used for the PPP connection). I was then able to use
KPPP to set up a dialer connection. I started the dialer and bam it connected. Once
connected I see this:
# ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3249 errors:0 dropped:0 overruns:0 frame:0
TX packets:3249 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13067764 (12.4 MiB) TX bytes:13067764 (12.4 MiB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:xx.11.222.aa P-t-P:yy.28.249.bb Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:3850 errors:0 dropped:0 overruns:0 frame:0
TX packets:3463 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:3681723 (3.5 MiB) TX bytes:532348 (519.8 KiB)
The only problem is that it is slow as glue. When I click on a website, it takes 30 to 90
seconds to respond. Once it actually starts pulling data, it seems a little quicker but
then bogs down when trying to go to the next website. I manually changed the
"serial" bit rate in the configuration files to the same way it was set in XP
(230400 bps) but that did not help.
In XP, the IP is set as follows:
Connected to NDIS:
Intel(R) PRO/100 VE Network Connection - Packet Scheduler Miniport
GUID: TRUCK4FC-E323-407D-B802-9D7F4412345
MAC Address: 00-14-3F-F5-1F-CB
Type: Ethernet Adapter
IPAddresses: 0.0.0.0
Gateway Addresses:
DHCP Enabled.
Lease Obtained Sun Aug 06 23:28:58 2006
Lease Expires Sun Aug 06 23:28:58 2006
DHCP Server Addresses: 192.168.1.1
WINS Disabled.
WAN (PPP/SLIP) Interface
GUID: 1234FAEE-F7D6-49F8-A71E-E9666BB54321
MAC Address: 00-53-45-00-00-00
Type: PPP Adapter
IPAddresses: YY.243.236.BB
Gateway Addresses: YY.243.236.BB
DHCP Disabled.
WINS Disabled.
Does anyone have any ideas?
Arch
That is an IPV6 address.
Can we see your: /etc/wvdial.conf ?
It is usually a matter of the 'correct' initialize/dial strings.
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
6:12 p.m.
Arch Willingham wrote:
Would it be called something else? There is no /etc/wvdial.conf file
on my system. Since I was firing it off with kpp, here is the config file (I'm making
a huge guess here):
/mycomputer/.kde/share/config/kppprc
pppdArguments=
[Account0]
AccountingEnabled=0
AccountingFile=
Authentication=4
AutoDNS=1
AutoName=0
BeforeConnect=
BeforeDisconnect=
CallbackPhone=
CallbackType=0
Command=
DNS=
DefaultRoute=1
DisconnectCommand=
Domain=
ExDNSDisabled=0
Gateway=0.0.0.0
IPAddr=0.0.0.0
Name=Sprint
Password=vzw
Phonenumber=#777
ScriptArguments=
ScriptCommands=
StorePassword=1
SubnetMask=0.0.0.0
Username=auburn(a)tigers.COM
VolumeAccountingEnabled=0
pppdArguments=
[General]
DefaultAccount=Sprint
DefaultModem=Sprint
NumberOfAccounts=1
NumberOfModems=1
PPPDebug=0
ShowLogWindow=1
[Graph]
Background=255,255,255
Enabled=true
InBytes=0,0,255
OutBytes=255,0,0
Text=0,0,0
[Modem0]
BusyWait=0
Device=/dev/ttyUSB0
Enter=CR
FlowControl=Hardware [CRTSCTS]
Name=Sprint
Speed=230400
Timeout=60
UseLockFile=1
Volume=1
WaitForDialTone=1
[WindowPosition]
WindowPositionConWinX=351
WindowPositionConWinY=328
WindowPositionStatWinX=326
WindowPositionStatWinY=175
Arch
-----Original Message-----
From: fedora-list-bounces(a)redhat.com
[mailto:fedora-list-bounces@redhat.com]On Behalf Of Phil Meyer
Sent: Thursday, May 24, 2007 4:43 PM
To: For users of Fedora
Subject: Re: Sprint Novatel Ovation U720 USB phone very slow on Fedora
Arch Willingham wrote:
> I am trying to install a Sprint Mobile Broadband USB Modem (Novatel Ovation U720)
cellular USB phone on a Dell laptop running FC7 test4. I found a variety of instructions
on getting it to work with FC6 and applied it to my install and it works..sort of.
>
> I have the laptop set to dual boot with XP. I first made sure it worked under XP. It
does and it extremely fast. I then did the install on FC7. After issuing
"/sbin/modprobe usbserial vendor=0×1410 product=0×2110". Once that was done, the
modem appeared as /dev/ttyUSB0 and /dev/ttyUSB1 (someone said they think the latter is a
management and diagnostic interface; the former is used for the PPP connection). I was
then able to use KPPP to set up a dialer connection. I started the dialer and bam it
connected. Once connected I see this:
>
> # ifconfig
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:3249 errors:0 dropped:0 overruns:0 frame:0
> TX packets:3249 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:13067764 (12.4 MiB) TX bytes:13067764 (12.4 MiB)
>
> ppp0 Link encap:Point-to-Point Protocol
> inet addr:xx.11.222.aa P-t-P:yy.28.249.bb Mask:255.255.255.255
> UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
> RX packets:3850 errors:0 dropped:0 overruns:0 frame:0
> TX packets:3463 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:3
> RX bytes:3681723 (3.5 MiB) TX bytes:532348 (519.8 KiB)
>
> The only problem is that it is slow as glue. When I click on a website, it takes 30
to 90 seconds to respond. Once it actually starts pulling data, it seems a little quicker
but then bogs down when trying to go to the next website. I manually changed the
"serial" bit rate in the configuration files to the same way it was set in XP
(230400 bps) but that did not help.
>
> In XP, the IP is set as follows:
>
> Connected to NDIS:
> Intel(R) PRO/100 VE Network Connection - Packet Scheduler Miniport
> GUID: TRUCK4FC-E323-407D-B802-9D7F4412345
> MAC Address: 00-14-3F-F5-1F-CB
> Type: Ethernet Adapter
> IPAddresses: 0.0.0.0
> Gateway Addresses:
> DHCP Enabled.
> Lease Obtained Sun Aug 06 23:28:58 2006
> Lease Expires Sun Aug 06 23:28:58 2006
> DHCP Server Addresses: 192.168.1.1
> WINS Disabled.
>
>
> WAN (PPP/SLIP) Interface
> GUID: 1234FAEE-F7D6-49F8-A71E-E9666BB54321
> MAC Address: 00-53-45-00-00-00
> Type: PPP Adapter
> IPAddresses: YY.243.236.BB
> Gateway Addresses: YY.243.236.BB
> DHCP Disabled.
> WINS Disabled.
>
> Does anyone have any ideas?
>
> Arch
>
>
>
That is an IPV6 address.
Can we see your: /etc/wvdial.conf ?
It is usually a matter of the 'correct' initialize/dial strings.
No K bashing intended here:
wvdial is a package and required for dial up networking done with
system-config-network
However, none of that matters to the argument at hand, its just easier
for me to explain how to watch things.
With syslog set to debug you should be able to see the entire handshake
and any error messages or unexpected results.
We use both EVDO and GSM based cards on trucks. The computer on the
trucks run FC6. :)
----X----
#!/bin/sh
# add debug to syslog
ed << _EOF /etc/syslog.conf
/local7/
a
# Debug
*.debug /var/log/debug
.
w
q
_EOF
touch /var/log/debug
chmod 644 /var/log/debug
service syslog restart
----X----
Now you can:
% tail -f /var/log/debug
and watch the entire conversation during a dial up.
What you are looking for are the strings that begin with sending the
modem 'AT'.
At the least you should see 'ATZ' and or 'ATM0' or something like:
'ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0'
These are all sort of generic initialization strings.
Unfortunately for use we cannot see what Windows driver is sending to
the modem, but it will contain something like these.
This forum expresses similar issues as you are having ...
http://www.evdoforums.com/thread3308.html
The speed issue is explained here:
http://samat.org/weblog/20070127-high-speed-cellular-wireless-modems-in-u...
"Switching from 1xRTT to EVDO is not automatic (though I believe EVDO to
1xRTT is). On Windows, I believe this is done manually by the connection
manager software…"
This means that a dial up initialization string (AT command) needs to be
added, or that a command has to be sent on the command channel (ttyUSB1)
to set the mode.
Using the above degug data you should see a response from Sprint as to
which mode is established when connecting.
The PCMCIA versions of similar cards default to EVDO mode (thankfully),
but this one may not.
Beyond this, its not clear to me yet how to change the mode.
Hope this helps a little.
Good Luck!
12:04 p.m.
I finally got a chance to try this and used the wvdial thing vs. kpp. It works great! It
was pretty dang fast.
Now I have one more dumb question. I have it set as a network interface. So, in order to
get to it, they have to click system > network > administration > network and
then they activate the interface. When they do that, it asks for the root password. Is
there no way to activate that without supplying the root password?
The guy was taking the laptop out of town. I did not notice the problem until 3 minutes
before he left and did not have time to dig into the answer.
Any ideas?
Arch
-----Original Message-----
From: fedora-list-bounces(a)redhat.com
[mailto:fedora-list-bounces@redhat.com]On Behalf Of Phil Meyer
Sent: Thursday, May 24, 2007 7:13 PM
To: For users of Fedora
Subject: Re: Sprint Novatel Ovation U720 USB phone very slow on Fedora
Arch Willingham wrote:
Would it be called something else? There is no /etc/wvdial.conf file
on my system. Since I was firing it off with kpp, here is the config file (I'm making
a huge guess here):
/mycomputer/.kde/share/config/kppprc
pppdArguments=
[Account0]
AccountingEnabled=0
AccountingFile=
Authentication=4
AutoDNS=1
AutoName=0
BeforeConnect=
BeforeDisconnect=
CallbackPhone=
CallbackType=0
Command=
DNS=
DefaultRoute=1
DisconnectCommand=
Domain=
ExDNSDisabled=0
Gateway=0.0.0.0
IPAddr=0.0.0.0
Name=Sprint
Password=vzw
Phonenumber=#777
ScriptArguments=
ScriptCommands=
StorePassword=1
SubnetMask=0.0.0.0
Username=auburn(a)tigers.COM
VolumeAccountingEnabled=0
pppdArguments=
[General]
DefaultAccount=Sprint
DefaultModem=Sprint
NumberOfAccounts=1
NumberOfModems=1
PPPDebug=0
ShowLogWindow=1
[Graph]
Background=255,255,255
Enabled=true
InBytes=0,0,255
OutBytes=255,0,0
Text=0,0,0
[Modem0]
BusyWait=0
Device=/dev/ttyUSB0
Enter=CR
FlowControl=Hardware [CRTSCTS]
Name=Sprint
Speed=230400
Timeout=60
UseLockFile=1
Volume=1
WaitForDialTone=1
[WindowPosition]
WindowPositionConWinX=351
WindowPositionConWinY=328
WindowPositionStatWinX=326
WindowPositionStatWinY=175
Arch
-----Original Message-----
From: fedora-list-bounces(a)redhat.com
[mailto:fedora-list-bounces@redhat.com]On Behalf Of Phil Meyer
Sent: Thursday, May 24, 2007 4:43 PM
To: For users of Fedora
Subject: Re: Sprint Novatel Ovation U720 USB phone very slow on Fedora
Arch Willingham wrote:
> I am trying to install a Sprint Mobile Broadband USB Modem (Novatel Ovation U720)
cellular USB phone on a Dell laptop running FC7 test4. I found a variety of instructions
on getting it to work with FC6 and applied it to my install and it works..sort of.
>
> I have the laptop set to dual boot with XP. I first made sure it worked under XP. It
does and it extremely fast. I then did the install on FC7. After issuing
"/sbin/modprobe usbserial vendor=0×1410 product=0×2110". Once that was done, the
modem appeared as /dev/ttyUSB0 and /dev/ttyUSB1 (someone said they think the latter is a
management and diagnostic interface; the former is used for the PPP connection). I was
then able to use KPPP to set up a dialer connection. I started the dialer and bam it
connected. Once connected I see this:
>
> # ifconfig
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:3249 errors:0 dropped:0 overruns:0 frame:0
> TX packets:3249 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:13067764 (12.4 MiB) TX bytes:13067764 (12.4 MiB)
>
> ppp0 Link encap:Point-to-Point Protocol
> inet addr:xx.11.222.aa P-t-P:yy.28.249.bb Mask:255.255.255.255
> UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
> RX packets:3850 errors:0 dropped:0 overruns:0 frame:0
> TX packets:3463 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:3
> RX bytes:3681723 (3.5 MiB) TX bytes:532348 (519.8 KiB)
>
> The only problem is that it is slow as glue. When I click on a website, it takes 30
to 90 seconds to respond. Once it actually starts pulling data, it seems a little quicker
but then bogs down when trying to go to the next website. I manually changed the
"serial" bit rate in the configuration files to the same way it was set in XP
(230400 bps) but that did not help.
>
> In XP, the IP is set as follows:
>
> Connected to NDIS:
> Intel(R) PRO/100 VE Network Connection - Packet Scheduler Miniport
> GUID: TRUCK4FC-E323-407D-B802-9D7F4412345
> MAC Address: 00-14-3F-F5-1F-CB
> Type: Ethernet Adapter
> IPAddresses: 0.0.0.0
> Gateway Addresses:
> DHCP Enabled.
> Lease Obtained Sun Aug 06 23:28:58 2006
> Lease Expires Sun Aug 06 23:28:58 2006
> DHCP Server Addresses: 192.168.1.1
> WINS Disabled.
>
>
> WAN (PPP/SLIP) Interface
> GUID: 1234FAEE-F7D6-49F8-A71E-E9666BB54321
> MAC Address: 00-53-45-00-00-00
> Type: PPP Adapter
> IPAddresses: YY.243.236.BB
> Gateway Addresses: YY.243.236.BB
> DHCP Disabled.
> WINS Disabled.
>
> Does anyone have any ideas?
>
> Arch
>
>
>
That is an IPV6 address.
Can we see your: /etc/wvdial.conf ?
It is usually a matter of the 'correct' initialize/dial strings.
No K bashing intended here:
wvdial is a package and required for dial up networking done with
system-config-network
However, none of that matters to the argument at hand, its just easier
for me to explain how to watch things.
With syslog set to debug you should be able to see the entire handshake
and any error messages or unexpected results.
We use both EVDO and GSM based cards on trucks. The computer on the
trucks run FC6. :)
----X----
#!/bin/sh
# add debug to syslog
ed << _EOF /etc/syslog.conf
/local7/
a
# Debug
*.debug /var/log/debug
.
w
q
_EOF
touch /var/log/debug
chmod 644 /var/log/debug
service syslog restart
----X----
Now you can:
% tail -f /var/log/debug
and watch the entire conversation during a dial up.
What you are looking for are the strings that begin with sending the
modem 'AT'.
At the least you should see 'ATZ' and or 'ATM0' or something like:
'ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0'
These are all sort of generic initialization strings.
Unfortunately for use we cannot see what Windows driver is sending to
the modem, but it will contain something like these.
This forum expresses similar issues as you are having ...
http://www.evdoforums.com/thread3308.html
The speed issue is explained here:
http://samat.org/weblog/20070127-high-speed-cellular-wireless-modems-in-u...
"Switching from 1xRTT to EVDO is not automatic (though I believe EVDO to
1xRTT is). On Windows, I believe this is done manually by the connection
manager software…"
This means that a dial up initialization string (AT command) needs to be
added, or that a command has to be sent on the command channel (ttyUSB1)
to set the mode.
Using the above degug data you should see a response from Sprint as to
which mode is established when connecting.
The PCMCIA versions of similar cards default to EVDO mode (thankfully),
but this one may not.
Beyond this, its not clear to me yet how to change the mode.
Hope this helps a little.
Good Luck!
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
12:51 a.m.
On Fri, 2007-06-01 at 13:04 -0400, Arch Willingham wrote:
I finally got a chance to try this and used the wvdial thing vs.
kpp.
It works great! It was pretty dang fast.
Now I have one more dumb question. I have it set as a network
interface. So, in order to get to it, they have to click system >
network > administration > network and then they activate the
interface. When they do that, it asks for the root password. Is there
no way to activate that without supplying the root password?
The guy was taking the laptop out of town. I did not notice the
problem until 3 minutes before he left and did not have time to dig
into the answer.
Command line: ifup ppp0
(or whatever interface you want to bring up, instead of ppp0).
GUI: modemlights panel applet, or "network device control" in the
applications, system tools menu.
You only need the root password to configure the network. While
configuring it, there's an option to let any user bring that interface
up and down.
--
(This box runs FC6, my others run FC4 & FC5, in case that's
important to the thread.)
Don't send private replies to my address, the mailbox is ignored.
I read messages from the public lists.
6182
days inactive
6191
days old
5 comments
3 participants
participants (3)
-
Arch Willingham -
Phil Meyer -
Tim