[PATCH] Add patch set for AM33xx BeagleBones
Peter Robinson
pbrobinson at gmail.com
Mon Dec 2 00:41:28 UTC 2013
Hi Josh,
The is essentially a rebase of what we have in 3.11. I've split it
into two patches, the first I know has landed upstream for 3.13 and
the later either hasn't or I've not had time to look. There's one
outstanding issue that the network interface seems to have a crash and
I need to look at that some more, on the plus side both usb and hdmi
work. Even with the network issue (which I think we saw in initial
3.11 support, kyle might remember) I think it's worth landing this.
Peter
---
arm-am33xx-arm-soc-upstream.patch | 2468 +++++++++++++++++++++++++++++++++++++
arm-am33xx-bblack.patch | 610 +++++++++
config-armv7 | 5 +-
kernel.spec | 15 +-
4 files changed, 3095 insertions(+), 3 deletions(-)
create mode 100644 arm-am33xx-arm-soc-upstream.patch
create mode 100644 arm-am33xx-bblack.patch
diff --git a/arm-am33xx-arm-soc-upstream.patch
b/arm-am33xx-arm-soc-upstream.patch
new file mode 100644
index 0000000..3129c1a
--- /dev/null
+++ b/arm-am33xx-arm-soc-upstream.patch
@@ -0,0 +1,2468 @@
+Bugzilla: 1012025
+Upstream-status: Landed in 3.13-rc1
+
+From 9096ef3ab805b2e9fda732f3128a761810c1dea4 Mon Sep 17 00:00:00 2001
+From: Alexandre Belloni <alexandre.belloni at free-electrons.com>
+Date: Sat, 3 Aug 2013 20:00:54 +0200
+Subject: [PATCH 01/15] ARM: dts: AM33XX: Add PMU support
+
+ARM Performance Monitor Units are available on the am33xx,
+add the support in the dtsi.
+
+Tested with perf and oprofile on a regular beaglebone.
+
+Signed-off-by: Alexandre Belloni <alexandre.belloni at free-electrons.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am33xx.dtsi | 5 +++++
+ 1 file changed, 5 insertions(+)
+
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index f9c5da9..4d1c632 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -57,6 +57,11 @@
+ };
+ };
+
++ pmu {
++ compatible = "arm,cortex-a8-pmu";
++ interrupts = <3>;
++ };
++
+ /*
+ * The soc node represents the soc top level view. It is uses for IPs
+ * that are not memory mapped in the MPU view or for the MPU itself.
+--
+1.8.4.rc3
+
+From 41bae5a6301ff1cd48fd0c4ff32146059b8e1b73 Mon Sep 17 00:00:00 2001
+From: Lars Poeschel <poeschel at lemonage.de>
+Date: Wed, 7 Aug 2013 13:06:32 +0200
+Subject: [PATCH 02/15] ARM: dts: AM33xx: Correct gpio #interrupt-cells
+ property
+
+Following commit ff5c9059 and therefore other omap platforms using
+the gpio-omap driver correct the #interrupt-cells property on am33xx
+too. The omap gpio binding documentaion also states that
+the #interrupt-cells property should be 2.
+
+Signed-off-by: Lars Poeschel <poeschel at lemonage.de>
+Reviewed-by: Javier Martinez Canillas <javier at dowhile0.org>
+Acked-by: Mark Rutland <mark.rutland at arm.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am33xx.dtsi | 8 ++++----
+ 1 file changed, 4 insertions(+), 4 deletions(-)
+
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index 4d1c632..a7731ea 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -111,7 +111,7 @@
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+- #interrupt-cells = <1>;
++ #interrupt-cells = <2>;
+ reg = <0x44e07000 0x1000>;
+ interrupts = <96>;
+ };
+@@ -122,7 +122,7 @@
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+- #interrupt-cells = <1>;
++ #interrupt-cells = <2>;
+ reg = <0x4804c000 0x1000>;
+ interrupts = <98>;
+ };
+@@ -133,7 +133,7 @@
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+- #interrupt-cells = <1>;
++ #interrupt-cells = <2>;
+ reg = <0x481ac000 0x1000>;
+ interrupts = <32>;
+ };
+@@ -144,7 +144,7 @@
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+- #interrupt-cells = <1>;
++ #interrupt-cells = <2>;
+ reg = <0x481ae000 0x1000>;
+ interrupts = <62>;
+ };
+--
+1.8.4.rc3
+
+From 200835d6072367d401cc6eb76b05fef2a2919291 Mon Sep 17 00:00:00 2001
+From: Matt Porter <mdp at ti.com>
+Date: Tue, 10 Sep 2013 14:24:37 -0500
+Subject: [PATCH 03/15] ARM: dts: AM33XX: Add EDMA support
+
+Adds AM33XX EDMA support to the am33xx.dtsi as documented in
+Documentation/devicetree/bindings/dma/ti-edma.txt
+
+[Joel Fernandes <joelf at ti.com>]
+Drop DT entries that are non-hardware-description as discussed in [1]
+
+[1] https://patchwork.kernel.org/patch/2226761/
+
+Signed-off-by: Matt Porter <mporter at ti.com>
+Signed-off-by: Joel A Fernandes <joelagnel at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am33xx.dtsi | 12 ++++++++++++
+ 1 file changed, 12 insertions(+)
+
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index a7731ea..7a53e07 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -105,6 +105,18 @@
+ reg = <0x48200000 0x1000>;
+ };
+
++ edma: edma at 49000000 {
++ compatible = "ti,edma3";
++ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
++ reg = <0x49000000 0x10000>,
++ <0x44e10f90 0x10>;
++ interrupts = <12 13 14>;
++ #dma-cells = <1>;
++ dma-channels = <64>;
++ ti,edma-regions = <4>;
++ ti,edma-slots = <256>;
++ };
++
+ gpio0: gpio at 44e07000 {
+ compatible = "ti,omap4-gpio";
+ ti,hwmods = "gpio1";
+--
+1.8.4.rc3
+
+From 62ca70c0e2dfc1a4e9225b801cd769fd92f6de7c Mon Sep 17 00:00:00 2001
+From: Matt Porter <mporter at ti.com>
+Date: Tue, 10 Sep 2013 14:24:38 -0500
+Subject: [PATCH 04/15] ARM: dts: AM33XX: Add SPI DMA support
+
+Adds DMA resources to the AM33XX SPI nodes.
+
+Signed-off-by: Matt Porter <mporter at ti.com>
+Signed-off-by: Joel A Fernandes <joelagnel at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am33xx.dtsi | 10 ++++++++++
+ 1 file changed, 10 insertions(+)
+
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index 7a53e07..9cd60bf 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -340,6 +340,11 @@
+ interrupts = <65>;
+ ti,spi-num-cs = <2>;
+ ti,hwmods = "spi0";
++ dmas = <&edma 16
++ &edma 17
++ &edma 18
++ &edma 19>;
++ dma-names = "tx0", "rx0", "tx1", "rx1";
+ status = "disabled";
+ };
+
+@@ -351,6 +356,11 @@
+ interrupts = <125>;
+ ti,spi-num-cs = <2>;
+ ti,hwmods = "spi1";
++ dmas = <&edma 42
++ &edma 43
++ &edma 44
++ &edma 45>;
++ dma-names = "tx0", "rx0", "tx1", "rx1";
+ status = "disabled";
+ };
+
+--
+1.8.4.rc3
+
+From de80038efb2254fd72e77f848eb867fc193b5a74 Mon Sep 17 00:00:00 2001
+From: Matt Porter <mporter at ti.com>
+Date: Tue, 10 Sep 2013 14:24:39 -0500
+Subject: [PATCH 05/15] ARM: dts: AM33XX: Add MMC support and documentation
+
+Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.
+
+Also added is the DMA binding definitions based on the generic DMA request
+binding.
+
+Additional changes made to DTS:
+* Interrupt, reg and compatible properties added
+* ti,needs-special-hs-handling added
+
+Signed-off-by: Matt Porter <mporter at ti.com>
+Acked-by: Tony Lindgren <tony at atomide.com>
+Signed-off-by: Joel Fernandes <joelf at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ .../devicetree/bindings/mmc/ti-omap-hsmmc.txt | 26 ++++++++++++++-
+ arch/arm/boot/dts/am335x-bone.dts | 11 +++++++
+ arch/arm/boot/dts/am335x-evm.dts | 7 ++++
+ arch/arm/boot/dts/am335x-evmsk.dts | 7 ++++
+ arch/arm/boot/dts/am33xx.dtsi | 38 ++++++++++++++++++++++
+ 5 files changed, 88 insertions(+), 1 deletion(-)
+
+diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+index ed271fc..8c8908a 100644
+--- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
++++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+@@ -20,8 +20,29 @@ ti,dual-volt: boolean, supports dual voltage cards
+ ti,non-removable: non-removable slot (like eMMC)
+ ti,needs-special-reset: Requires a special softreset sequence
+ ti,needs-special-hs-handling: HSMMC IP needs special setting for
handling High Speed
++dmas: List of DMA specifiers with the controller specific format
++as described in the generic DMA client binding. A tx and rx
++specifier is required.
++dma-names: List of DMA request names. These strings correspond
++1:1 with the DMA specifiers listed in dmas. The string naming is
++to be "rx" and "tx" for RX and TX DMA requests, respectively.
++
++Examples:
++
++[hwmod populated DMA resources]
++
++ mmc1: mmc at 0x4809c000 {
++ compatible = "ti,omap4-hsmmc";
++ reg = <0x4809c000 0x400>;
++ ti,hwmods = "mmc1";
++ ti,dual-volt;
++ bus-width = <4>;
++ vmmc-supply = <&vmmc>; /* phandle to regulator node */
++ ti,non-removable;
++ };
++
++[generic DMA request binding]
+
+-Example:
+ mmc1: mmc at 0x4809c000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x4809c000 0x400>;
+@@ -30,4 +51,7 @@ Example:
+ bus-width = <4>;
+ vmmc-supply = <&vmmc>; /* phandle to regulator node */
+ ti,non-removable;
++ dmas = <&edma 24
++ &edma 25>;
++ dma-names = "tx", "rx";
+ };
+diff --git a/arch/arm/boot/dts/am335x-bone.dts
b/arch/arm/boot/dts/am335x-bone.dts
+index 7993c48..d5f43fe 100644
+--- a/arch/arm/boot/dts/am335x-bone.dts
++++ b/arch/arm/boot/dts/am335x-bone.dts
+@@ -9,3 +9,14 @@
+
+ #include "am33xx.dtsi"
+ #include "am335x-bone-common.dtsi"
++
++&ldo3_reg {
++ regulator-min-microvolt = <1800000>;
++ regulator-max-microvolt = <3300000>;
++ regulator-always-on;
++};
++
++&mmc1 {
++ status = "okay";
++ vmmc-supply = <&ldo3_reg>;
++};
+diff --git a/arch/arm/boot/dts/am335x-evm.dts
b/arch/arm/boot/dts/am335x-evm.dts
+index e8ec875..bc4a69d 100644
+--- a/arch/arm/boot/dts/am335x-evm.dts
++++ b/arch/arm/boot/dts/am335x-evm.dts
+@@ -477,6 +477,8 @@
+ };
+
+ vmmc_reg: regulator at 12 {
++ regulator-min-microvolt = <1800000>;
++ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+@@ -517,3 +519,8 @@
+ ti,adc-channels = <4 5 6 7>;
+ };
+ };
++
++&mmc1 {
++ status = "okay";
++ vmmc-supply = <&vmmc_reg>;
++};
+diff --git a/arch/arm/boot/dts/am335x-evmsk.dts
b/arch/arm/boot/dts/am335x-evmsk.dts
+index 4f339fa..55fd194 100644
+--- a/arch/arm/boot/dts/am335x-evmsk.dts
++++ b/arch/arm/boot/dts/am335x-evmsk.dts
+@@ -393,6 +393,8 @@
+ };
+
+ vmmc_reg: regulator at 12 {
++ regulator-min-microvolt = <1800000>;
++ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+@@ -419,3 +421,8 @@
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "rgmii-txid";
+ };
++
++&mmc1 {
++ status = "okay";
++ vmmc-supply = <&vmmc_reg>;
++};
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index 9cd60bf..553adc6 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -245,6 +245,44 @@
+ status = "disabled";
+ };
+
++ mmc1: mmc at 48060000 {
++ compatible = "ti,omap4-hsmmc";
++ ti,hwmods = "mmc1";
++ ti,dual-volt;
++ ti,needs-special-reset;
++ ti,needs-special-hs-handling;
++ dmas = <&edma 24
++ &edma 25>;
++ dma-names = "tx", "rx";
++ interrupts = <64>;
++ interrupt-parent = <&intc>;
++ reg = <0x48060000 0x1000>;
++ status = "disabled";
++ };
++
++ mmc2: mmc at 481d8000 {
++ compatible = "ti,omap4-hsmmc";
++ ti,hwmods = "mmc2";
++ ti,needs-special-reset;
++ dmas = <&edma 2
++ &edma 3>;
++ dma-names = "tx", "rx";
++ interrupts = <28>;
++ interrupt-parent = <&intc>;
++ reg = <0x481d8000 0x1000>;
++ status = "disabled";
++ };
++
++ mmc3: mmc at 47810000 {
++ compatible = "ti,omap4-hsmmc";
++ ti,hwmods = "mmc3";
++ ti,needs-special-reset;
++ interrupts = <29>;
++ interrupt-parent = <&intc>;
++ reg = <0x47810000 0x1000>;
++ status = "disabled";
++ };
++
+ wdt2: wdt at 44e35000 {
+ compatible = "ti,omap3-wdt";
+ ti,hwmods = "wd_timer2";
+--
+1.8.4.rc3
+
+From 889d5b18a88681d7d1e5a1d1b5d2ffda07c506df Mon Sep 17 00:00:00 2001
+From: Alexander Holler <holler at ahsoftware.de>
+Date: Thu, 12 Sep 2013 20:35:32 +0200
+Subject: [PATCH 06/15] ARM: dts: am335x-bone: add CD for mmc1
+
+This enables the use of MMC cards even when no card was inserted at boot.
+
+Signed-off-by: Alexander Holler <holler at ahsoftware.de>
+Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
+Tested-by: Kevin Hilman <khilman at linaro.org>
+Reviewed-by: Nishanth Menon <nm at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 14 ++++++++++++++
+ arch/arm/boot/dts/am335x-bone.dts | 1 -
+ 2 files changed, 14 insertions(+), 1 deletion(-)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index 2f66ded..0d95d54 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -107,6 +107,12 @@
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
++
++ mmc1_pins: pinmux_mmc1_pins {
++ pinctrl-single,pins = <
++ 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
++ >;
++ };
+ };
+
+ ocp {
+@@ -260,3 +266,11 @@
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ };
++
++&mmc1 {
++ status = "okay";
++ pinctrl-names = "default";
++ pinctrl-0 = <&mmc1_pins>;
++ cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
++ cd-inverted;
++};
+diff --git a/arch/arm/boot/dts/am335x-bone.dts
b/arch/arm/boot/dts/am335x-bone.dts
+index d5f43fe..0d63348 100644
+--- a/arch/arm/boot/dts/am335x-bone.dts
++++ b/arch/arm/boot/dts/am335x-bone.dts
+@@ -17,6 +17,5 @@
+ };
+
+ &mmc1 {
+- status = "okay";
+ vmmc-supply = <&ldo3_reg>;
+ };
+--
+1.8.4.rc3
+
+From 7e60fa2391c2e89f07452c2037209235dee67aee Mon Sep 17 00:00:00 2001
+From: Koen Kooi <koen at dominion.thruhere.net>
+Date: Thu, 12 Sep 2013 20:35:33 +0200
+Subject: [PATCH 07/15] ARM: dts: am335x-boneblack: add eMMC DT entry
+
+The pinmux is specified in am335x-bone-common.dtsi to be
+reused by the eMMC cape.
+
+Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
+Tested-by: Kevin Hilman <khilman at linaro.org>
+Reviewed-by: Nishanth Menon <nm at ti.com>
+[bcousson at baylibre.com: Fix traling spaces and useless comments]
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 22 ++++++++++++++++++++++
+ arch/arm/boot/dts/am335x-boneblack.dts | 13 +++++++++++++
+ 2 files changed, 35 insertions(+)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index 0d95d54..c560cb7 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -113,6 +113,21 @@
+ 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
+ >;
+ };
++
++ emmc_pins: pinmux_emmc_pins {
++ pinctrl-single,pins = <
++ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
++ 0x84 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_csn2.mmc1_cmd */
++ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
++ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
++ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
++ 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
++ 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
++ 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
++ 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
++ 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
++ >;
++ };
+ };
+
+ ocp {
+@@ -242,6 +257,13 @@
+ regulator-always-on;
+ };
+ };
++
++ vmmcsd_fixed: fixedregulator at 0 {
++ compatible = "regulator-fixed";
++ regulator-name = "vmmcsd_fixed";
++ regulator-min-microvolt = <3300000>;
++ regulator-max-microvolt = <3300000>;
++ };
+ };
+
+ &cpsw_emac0 {
+diff --git a/arch/arm/boot/dts/am335x-boneblack.dts
b/arch/arm/boot/dts/am335x-boneblack.dts
+index 197cadf..16b3bea 100644
+--- a/arch/arm/boot/dts/am335x-boneblack.dts
++++ b/arch/arm/boot/dts/am335x-boneblack.dts
+@@ -15,3 +15,16 @@
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
++
++&mmc1 {
++ vmmc-supply = <&vmmcsd_fixed>;
++};
++
++&mmc2 {
++ vmmc-supply = <&vmmcsd_fixed>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&emmc_pins>;
++ bus-width = <8>;
++ status = "okay";
++ ti,vcc-aux-disable-is-sleep;
++};
+--
+1.8.4.rc3
+
+From 2b3a35fea12469734e2216a06c7fea6d5cb0d4d8 Mon Sep 17 00:00:00 2001
+From: Koen Kooi <koen at dominion.thruhere.net>
+Date: Thu, 12 Sep 2013 20:35:34 +0200
+Subject: [PATCH 08/15] ARM: dts: am335x-bone-common: switch mmc1 to 4-bit mode
+
+The micro-SD slot hooks up all four data pins so lets' use them.
+
+Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
+Tested-by: Kevin Hilman <khilman at linaro.org>
+Reviewed-by: Nishanth Menon <nm at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 1 +
+ 1 file changed, 1 insertion(+)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index c560cb7..fbb11dd 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -291,6 +291,7 @@
+
+ &mmc1 {
+ status = "okay";
++ bus-width = <0x4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+--
+1.8.4.rc3
+
+From 387d315741b4126f228ee788094f9a00ecf8fde0 Mon Sep 17 00:00:00 2001
+From: Koen Kooi <koen at dominion.thruhere.net>
+Date: Thu, 12 Sep 2013 20:35:35 +0200
+Subject: [PATCH 09/15] ARM: dts: am335x-bone-common: add cpu0 and mmc1
+ triggers
+
+This matches the vendor 3.8.x configuration that is shipping
+with the boards.
+
+The LED layout is now:
+ USR0: heartbeat
+ USR1: mmc0 (micro-SD slot)
+ USR2: cpu0
+ USR3: mmc1 (eMMC)
+
+The cpu0 triggers was put in between the mmc triggers to make
+is easier to see where the disk activity is.
+
+Signed-off-by: Koen Kooi <koen at dominion.thruhere.net>
+Tested-by: Kevin Hilman <khilman at linaro.org>
+Reviewed-by: Nishanth Menon <nm at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 2 ++
+ 1 file changed, 2 insertions(+)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index fbb11dd..56361ce 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -204,12 +204,14 @@
+ led at 4 {
+ label = "beaglebone:green:usr2";
+ gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
++ linux,default-trigger = "cpu0";
+ default-state = "off";
+ };
+
+ led at 5 {
+ label = "beaglebone:green:usr3";
+ gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
++ linux,default-trigger = "mmc1";
+ default-state = "off";
+ };
+ };
+--
+1.8.4.rc3
+
+From 28d36734db6d9682208ced9032de9ebda568da96 Mon Sep 17 00:00:00 2001
+From: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
+Date: Fri, 20 Sep 2013 17:00:00 +0200
+Subject: [PATCH 10/15] ARM: dts: AM33XX: use pinmux node defined in included
+ file
+
+am33xx boards DTS include the am33xx.dtsi Device Tree
+source file that already define a pinmux device node for
+the AM33XX SoC Pin Multiplex.
+
+Redefining this for each board makes the Device Tree files
+harder to modify and maintain so let's just use what is
+already defined in the included .dtsi file.
+
+Signed-off-by: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 218 ++++++++++++-------------
+ arch/arm/boot/dts/am335x-evm.dts | 254 ++++++++++++++---------------
+ arch/arm/boot/dts/am335x-evmsk.dts | 258 +++++++++++++++---------------
+ 3 files changed, 365 insertions(+), 365 deletions(-)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index 56361ce..29799ac 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -21,115 +21,6 @@
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+- am33xx_pinmux: pinmux at 44e10800 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&clkout2_pin>;
+-
+- user_leds_s0: user_leds_s0 {
+- pinctrl-single,pins = <
+- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_a5.gpio1_21 */
+- 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
+- 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_a7.gpio1_23 */
+- 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
+- >;
+- };
+-
+- i2c0_pins: pinmux_i2c0_pins {
+- pinctrl-single,pins = <
+- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /*
i2c0_sda.i2c0_sda */
+- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /*
i2c0_scl.i2c0_scl */
+- >;
+- };
+-
+- uart0_pins: pinmux_uart0_pins {
+- pinctrl-single,pins = <
+- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /*
uart0_rxd.uart0_rxd */
+- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
uart0_txd.uart0_txd */
+- >;
+- };
+-
+- clkout2_pin: pinmux_clkout2_pin {
+- pinctrl-single,pins = <
+- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /*
xdma_event_intr1.clkout2 */
+- >;
+- };
+-
+- cpsw_default: cpsw_default {
+- pinctrl-single,pins = <
+- /* Slave 1 */
+- 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxerr.mii1_rxerr */
+- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txen.mii1_txen */
+- 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxdv.mii1_rxdv */
+- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd3.mii1_txd3 */
+- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd2.mii1_txd2 */
+- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd1.mii1_txd1 */
+- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd0.mii1_txd0 */
+- 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_txclk.mii1_txclk */
+- 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxclk.mii1_rxclk */
+- 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxd3.mii1_rxd3 */
+- 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxd2.mii1_rxd2 */
+- 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxd1.mii1_rxd1 */
+- 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxd0.mii1_rxd0 */
+- >;
+- };
+-
+- cpsw_sleep: cpsw_sleep {
+- pinctrl-single,pins = <
+- /* Slave 1 reset value */
+- 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- >;
+- };
+-
+- davinci_mdio_default: davinci_mdio_default {
+- pinctrl-single,pins = <
+- /* MDIO */
+- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
/* mdio_data.mdio_data */
+- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /*
mdio_clk.mdio_clk */
+- >;
+- };
+-
+- davinci_mdio_sleep: davinci_mdio_sleep {
+- pinctrl-single,pins = <
+- /* MDIO reset value */
+- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- >;
+- };
+-
+- mmc1_pins: pinmux_mmc1_pins {
+- pinctrl-single,pins = <
+- 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
+- >;
+- };
+-
+- emmc_pins: pinmux_emmc_pins {
+- pinctrl-single,pins = <
+- 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+- 0x84 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_csn2.mmc1_cmd */
+- 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+- 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+- 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+- 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+- 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
+- 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
+- 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
+- 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
+- >;
+- };
+- };
+-
+ ocp {
+ uart0: serial at 44e09000 {
+ pinctrl-names = "default";
+@@ -217,6 +108,115 @@
+ };
+ };
+
++&am33xx_pinmux {
++ pinctrl-names = "default";
++ pinctrl-0 = <&clkout2_pin>;
++
++ user_leds_s0: user_leds_s0 {
++ pinctrl-single,pins = <
++ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
++ 0x58 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a6.gpio1_22 */
++ 0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a7.gpio1_23 */
++ 0x60 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_a8.gpio1_24 */
++ >;
++ };
++
++ i2c0_pins: pinmux_i2c0_pins {
++ pinctrl-single,pins = <
++ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
++ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
++ >;
++ };
++
++ uart0_pins: pinmux_uart0_pins {
++ pinctrl-single,pins = <
++ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
++ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
uart0_txd.uart0_txd */
++ >;
++ };
++
++ clkout2_pin: pinmux_clkout2_pin {
++ pinctrl-single,pins = <
++ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /*
xdma_event_intr1.clkout2 */
++ >;
++ };
++
++ cpsw_default: cpsw_default {
++ pinctrl-single,pins = <
++ /* Slave 1 */
++ 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxerr.mii1_rxerr */
++ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txen.mii1_txen */
++ 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxdv.mii1_rxdv */
++ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd3.mii1_txd3 */
++ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd2.mii1_txd2 */
++ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd1.mii1_txd1 */
++ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
mii1_txd0.mii1_txd0 */
++ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_txclk.mii1_txclk */
++ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /*
mii1_rxclk.mii1_rxclk */
++ 0x134 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd3.mii1_rxd3 */
++ 0x138 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd2.mii1_rxd2 */
++ 0x13c (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd1.mii1_rxd1 */
++ 0x140 (PIN_INPUT_PULLUP | MUX_MODE0) /* mii1_rxd0.mii1_rxd0 */
++ >;
++ };
++
++ cpsw_sleep: cpsw_sleep {
++ pinctrl-single,pins = <
++ /* Slave 1 reset value */
++ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ >;
++ };
++
++ davinci_mdio_default: davinci_mdio_default {
++ pinctrl-single,pins = <
++ /* MDIO */
++ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
/* mdio_data.mdio_data */
++ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /*
mdio_clk.mdio_clk */
++ >;
++ };
++
++ davinci_mdio_sleep: davinci_mdio_sleep {
++ pinctrl-single,pins = <
++ /* MDIO reset value */
++ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ >;
++ };
++
++ mmc1_pins: pinmux_mmc1_pins {
++ pinctrl-single,pins = <
++ 0x160 (PIN_INPUT | MUX_MODE7) /* GPIO0_6 */
++ >;
++ };
++
++ emmc_pins: pinmux_emmc_pins {
++ pinctrl-single,pins = <
++ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
++ 0x84 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_csn2.mmc1_cmd */
++ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
++ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
++ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
++ 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
++ 0x10 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad4.mmc1_dat4 */
++ 0x14 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad5.mmc1_dat5 */
++ 0x18 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad6.mmc1_dat6 */
++ 0x1c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad7.mmc1_dat7 */
++ >;
++ };
++};
++
+ /include/ "tps65217.dtsi"
+
+ &tps {
+diff --git a/arch/arm/boot/dts/am335x-evm.dts
b/arch/arm/boot/dts/am335x-evm.dts
+index bc4a69d..1525cd6 100644
+--- a/arch/arm/boot/dts/am335x-evm.dts
++++ b/arch/arm/boot/dts/am335x-evm.dts
+@@ -24,133 +24,6 @@
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+- am33xx_pinmux: pinmux at 44e10800 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
+-
+- matrix_keypad_s0: matrix_keypad_s0 {
+- pinctrl-single,pins = <
+- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_a5.gpio1_21 */
+- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_a6.gpio1_22 */
+- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_a9.gpio1_25 */
+- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_a10.gpio1_26 */
+- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_a11.gpio1_27 */
+- >;
+- };
+-
+- volume_keys_s0: volume_keys_s0 {
+- pinctrl-single,pins = <
+- 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
spi0_sclk.gpio0_2 */
+- 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
spi0_d0.gpio0_3 */
+- >;
+- };
+-
+- i2c0_pins: pinmux_i2c0_pins {
+- pinctrl-single,pins = <
+- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /*
i2c0_sda.i2c0_sda */
+- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /*
i2c0_scl.i2c0_scl */
+- >;
+- };
+-
+- i2c1_pins: pinmux_i2c1_pins {
+- pinctrl-single,pins = <
+- 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
+- 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /*
spi0_cs0.i2c1_scl */
+- >;
+- };
+-
+- uart0_pins: pinmux_uart0_pins {
+- pinctrl-single,pins = <
+- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /*
uart0_rxd.uart0_rxd */
+- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
uart0_txd.uart0_txd */
+- >;
+- };
+-
+- clkout2_pin: pinmux_clkout2_pin {
+- pinctrl-single,pins = <
+- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /*
xdma_event_intr1.clkout2 */
+- >;
+- };
+-
+- nandflash_pins_s0: nandflash_pins_s0 {
+- pinctrl-single,pins = <
+- 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
+- 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
+- 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
+- 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
+- 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
+- 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
+- 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
+- 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
+- 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /*
gpmc_wait0.gpmc_wait0 */
+- 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
+- 0x7c (PIN_OUTPUT | MUX_MODE0) /*
gpmc_csn0.gpmc_csn0 */
+- 0x90 (PIN_OUTPUT | MUX_MODE0) /*
gpmc_advn_ale.gpmc_advn_ale */
+- 0x94 (PIN_OUTPUT | MUX_MODE0) /*
gpmc_oen_ren.gpmc_oen_ren */
+- 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
+- 0x9c (PIN_OUTPUT | MUX_MODE0) /*
gpmc_be0n_cle.gpmc_be0n_cle */
+- >;
+- };
+-
+- ecap0_pins: backlight_pins {
+- pinctrl-single,pins = <
+- 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+- >;
+- };
+-
+- cpsw_default: cpsw_default {
+- pinctrl-single,pins = <
+- /* Slave 1 */
+- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txen.rgmii1_tctl */
+- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxdv.rgmii1_rctl */
+- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd3.rgmii1_td3 */
+- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd2.rgmii1_td2 */
+- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd1.rgmii1_td1 */
+- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd0.rgmii1_td0 */
+- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txclk.rgmii1_tclk */
+- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxclk.rgmii1_rclk */
+- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd3.rgmii1_rd3 */
+- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd2.rgmii1_rd2 */
+- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd1.rgmii1_rd1 */
+- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd0.rgmii1_rd0 */
+- >;
+- };
+-
+- cpsw_sleep: cpsw_sleep {
+- pinctrl-single,pins = <
+- /* Slave 1 reset value */
+- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- >;
+- };
+-
+- davinci_mdio_default: davinci_mdio_default {
+- pinctrl-single,pins = <
+- /* MDIO */
+- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
/* mdio_data.mdio_data */
+- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /*
mdio_clk.mdio_clk */
+- >;
+- };
+-
+- davinci_mdio_sleep: davinci_mdio_sleep {
+- pinctrl-single,pins = <
+- /* MDIO reset value */
+- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- >;
+- };
+- };
+-
+ ocp {
+ uart0: serial at 44e09000 {
+ pinctrl-names = "default";
+@@ -405,6 +278,133 @@
+ };
+ };
+
++&am33xx_pinmux {
++ pinctrl-names = "default";
++ pinctrl-0 = <&matrix_keypad_s0 &volume_keys_s0 &clkout2_pin>;
++
++ matrix_keypad_s0: matrix_keypad_s0 {
++ pinctrl-single,pins = <
++ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a5.gpio1_21 */
++ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a6.gpio1_22 */
++ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a9.gpio1_25 */
++ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a10.gpio1_26 */
++ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_a11.gpio1_27 */
++ >;
++ };
++
++ volume_keys_s0: volume_keys_s0 {
++ pinctrl-single,pins = <
++ 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_sclk.gpio0_2 */
++ 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* spi0_d0.gpio0_3 */
++ >;
++ };
++
++ i2c0_pins: pinmux_i2c0_pins {
++ pinctrl-single,pins = <
++ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
++ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
++ >;
++ };
++
++ i2c1_pins: pinmux_i2c1_pins {
++ pinctrl-single,pins = <
++ 0x158 (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_d1.i2c1_sda */
++ 0x15c (PIN_INPUT_PULLUP | MUX_MODE2) /* spi0_cs0.i2c1_scl */
++ >;
++ };
++
++ uart0_pins: pinmux_uart0_pins {
++ pinctrl-single,pins = <
++ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
++ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
uart0_txd.uart0_txd */
++ >;
++ };
++
++ clkout2_pin: pinmux_clkout2_pin {
++ pinctrl-single,pins = <
++ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /*
xdma_event_intr1.clkout2 */
++ >;
++ };
++
++ nandflash_pins_s0: nandflash_pins_s0 {
++ pinctrl-single,pins = <
++ 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
++ 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
++ 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
++ 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
++ 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
++ 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
++ 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
++ 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
++ 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
++ 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_30 */
++ 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
++ 0x90 (PIN_OUTPUT | MUX_MODE0) /*
gpmc_advn_ale.gpmc_advn_ale */
++ 0x94 (PIN_OUTPUT | MUX_MODE0) /*
gpmc_oen_ren.gpmc_oen_ren */
++ 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
++ 0x9c (PIN_OUTPUT | MUX_MODE0) /*
gpmc_be0n_cle.gpmc_be0n_cle */
++ >;
++ };
++
++ ecap0_pins: backlight_pins {
++ pinctrl-single,pins = <
++ 0x164 0x0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
++ >;
++ };
++
++ cpsw_default: cpsw_default {
++ pinctrl-single,pins = <
++ /* Slave 1 */
++ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txen.rgmii1_tctl */
++ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxdv.rgmii1_rctl */
++ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd3.rgmii1_td3 */
++ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd2.rgmii1_td2 */
++ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd1.rgmii1_td1 */
++ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd0.rgmii1_td0 */
++ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txclk.rgmii1_tclk */
++ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxclk.rgmii1_rclk */
++ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd3.rgmii1_rd3 */
++ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd2.rgmii1_rd2 */
++ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd1.rgmii1_rd1 */
++ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd0.rgmii1_rd0 */
++ >;
++ };
++
++ cpsw_sleep: cpsw_sleep {
++ pinctrl-single,pins = <
++ /* Slave 1 reset value */
++ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ >;
++ };
++
++ davinci_mdio_default: davinci_mdio_default {
++ pinctrl-single,pins = <
++ /* MDIO */
++ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
/* mdio_data.mdio_data */
++ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /*
mdio_clk.mdio_clk */
++ >;
++ };
++
++ davinci_mdio_sleep: davinci_mdio_sleep {
++ pinctrl-single,pins = <
++ /* MDIO reset value */
++ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ >;
++ };
++};
++
+ #include "tps65910.dtsi"
+
+ &tps {
+diff --git a/arch/arm/boot/dts/am335x-evmsk.dts
b/arch/arm/boot/dts/am335x-evmsk.dts
+index 55fd194..f0066fe 100644
+--- a/arch/arm/boot/dts/am335x-evmsk.dts
++++ b/arch/arm/boot/dts/am335x-evmsk.dts
+@@ -31,135 +31,6 @@
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+- am33xx_pinmux: pinmux at 44e10800 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
+-
+- user_leds_s0: user_leds_s0 {
+- pinctrl-single,pins = <
+- 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_ad4.gpio1_4 */
+- 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_ad5.gpio1_5 */
+- 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_ad6.gpio1_6 */
+- 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /*
gpmc_ad7.gpio1_7 */
+- >;
+- };
+-
+- gpio_keys_s0: gpio_keys_s0 {
+- pinctrl-single,pins = <
+- 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_oen_ren.gpio2_3 */
+- 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_advn_ale.gpio2_2 */
+- 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_wait0.gpio0_30 */
+- 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_ben0_cle.gpio2_5 */
+- >;
+- };
+-
+- i2c0_pins: pinmux_i2c0_pins {
+- pinctrl-single,pins = <
+- 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /*
i2c0_sda.i2c0_sda */
+- 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /*
i2c0_scl.i2c0_scl */
+- >;
+- };
+-
+- uart0_pins: pinmux_uart0_pins {
+- pinctrl-single,pins = <
+- 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /*
uart0_rxd.uart0_rxd */
+- 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
uart0_txd.uart0_txd */
+- >;
+- };
+-
+- clkout2_pin: pinmux_clkout2_pin {
+- pinctrl-single,pins = <
+- 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /*
xdma_event_intr1.clkout2 */
+- >;
+- };
+-
+- ecap2_pins: backlight_pins {
+- pinctrl-single,pins = <
+- 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
+- >;
+- };
+-
+- cpsw_default: cpsw_default {
+- pinctrl-single,pins = <
+- /* Slave 1 */
+- 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txen.rgmii1_tctl */
+- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxdv.rgmii1_rctl */
+- 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd3.rgmii1_td3 */
+- 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd2.rgmii1_td2 */
+- 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd1.rgmii1_td1 */
+- 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd0.rgmii1_td0 */
+- 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txclk.rgmii1_tclk */
+- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxclk.rgmii1_rclk */
+- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd3.rgmii1_rd3 */
+- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd2.rgmii1_rd2 */
+- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd1.rgmii1_rd1 */
+- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd0.rgmii1_rd0 */
+-
+- /* Slave 2 */
+- 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a0.rgmii2_tctl */
+- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a1.rgmii2_rctl */
+- 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a2.rgmii2_td3 */
+- 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a3.rgmii2_td2 */
+- 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a4.rgmii2_td1 */
+- 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a5.rgmii2_td0 */
+- 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a6.rgmii2_tclk */
+- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a7.rgmii2_rclk */
+- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a8.rgmii2_rd3 */
+- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a9.rgmii2_rd2 */
+- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a10.rgmii2_rd1 */
+- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a11.rgmii2_rd0 */
+- >;
+- };
+-
+- cpsw_sleep: cpsw_sleep {
+- pinctrl-single,pins = <
+- /* Slave 1 reset value */
+- 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+-
+- /* Slave 2 reset value*/
+- 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- >;
+- };
+-
+- davinci_mdio_default: davinci_mdio_default {
+- pinctrl-single,pins = <
+- /* MDIO */
+- 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
/* mdio_data.mdio_data */
+- 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /*
mdio_clk.mdio_clk */
+- >;
+- };
+-
+- davinci_mdio_sleep: davinci_mdio_sleep {
+- pinctrl-single,pins = <
+- /* MDIO reset value */
+- 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+- >;
+- };
+- };
+-
+ ocp {
+ uart0: serial at 44e09000 {
+ pinctrl-names = "default";
+@@ -321,6 +192,135 @@
+ };
+ };
+
++&am33xx_pinmux {
++ pinctrl-names = "default";
++ pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>;
++
++ user_leds_s0: user_leds_s0 {
++ pinctrl-single,pins = <
++ 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */
++ 0x14 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad5.gpio1_5 */
++ 0x18 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad6.gpio1_6 */
++ 0x1c (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad7.gpio1_7 */
++ >;
++ };
++
++ gpio_keys_s0: gpio_keys_s0 {
++ pinctrl-single,pins = <
++ 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_oen_ren.gpio2_3 */
++ 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_advn_ale.gpio2_2 */
++ 0x70 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_wait0.gpio0_30 */
++ 0x9c (PIN_INPUT_PULLDOWN | MUX_MODE7) /*
gpmc_ben0_cle.gpio2_5 */
++ >;
++ };
++
++ i2c0_pins: pinmux_i2c0_pins {
++ pinctrl-single,pins = <
++ 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
++ 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
++ >;
++ };
++
++ uart0_pins: pinmux_uart0_pins {
++ pinctrl-single,pins = <
++ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
++ 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /*
uart0_txd.uart0_txd */
++ >;
++ };
++
++ clkout2_pin: pinmux_clkout2_pin {
++ pinctrl-single,pins = <
++ 0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /*
xdma_event_intr1.clkout2 */
++ >;
++ };
++
++ ecap2_pins: backlight_pins {
++ pinctrl-single,pins = <
++ 0x19c 0x4 /* mcasp0_ahclkr.ecap2_in_pwm2_out MODE4 */
++ >;
++ };
++
++ cpsw_default: cpsw_default {
++ pinctrl-single,pins = <
++ /* Slave 1 */
++ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txen.rgmii1_tctl */
++ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxdv.rgmii1_rctl */
++ 0x11c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd3.rgmii1_td3 */
++ 0x120 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd2.rgmii1_td2 */
++ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd1.rgmii1_td1 */
++ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txd0.rgmii1_td0 */
++ 0x12c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
mii1_txclk.rgmii1_tclk */
++ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxclk.rgmii1_rclk */
++ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd3.rgmii1_rd3 */
++ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd2.rgmii1_rd2 */
++ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd1.rgmii1_rd1 */
++ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE2) /*
mii1_rxd0.rgmii1_rd0 */
++
++ /* Slave 2 */
++ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a0.rgmii2_tctl */
++ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a1.rgmii2_rctl */
++ 0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a2.rgmii2_td3 */
++ 0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a3.rgmii2_td2 */
++ 0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a4.rgmii2_td1 */
++ 0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /* gpmc_a5.rgmii2_td0 */
++ 0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2) /*
gpmc_a6.rgmii2_tclk */
++ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a7.rgmii2_rclk */
++ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a8.rgmii2_rd3 */
++ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a9.rgmii2_rd2 */
++ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a10.rgmii2_rd1 */
++ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2) /* gpmc_a11.rgmii2_rd0 */
++ >;
++ };
++
++ cpsw_sleep: cpsw_sleep {
++ pinctrl-single,pins = <
++ /* Slave 1 reset value */
++ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x11c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x120 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x12c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x130 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x134 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x138 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++
++ /* Slave 2 reset value*/
++ 0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ >;
++ };
++
++ davinci_mdio_default: davinci_mdio_default {
++ pinctrl-single,pins = <
++ /* MDIO */
++ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)
/* mdio_data.mdio_data */
++ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /*
mdio_clk.mdio_clk */
++ >;
++ };
++
++ davinci_mdio_sleep: davinci_mdio_sleep {
++ pinctrl-single,pins = <
++ /* MDIO reset value */
++ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
++ >;
++ };
++};
++
+ #include "tps65910.dtsi"
+
+ &tps {
+--
+1.8.4.rc3
+
+From ff7a46710ffc245a5c8e32cf1843aa3fea7aa1ff Mon Sep 17 00:00:00 2001
+From: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
+Date: Fri, 20 Sep 2013 17:42:19 +0200
+Subject: [PATCH 11/15] ARM: dts: AM33XX: don't redefine OCP bus and device
+ nodes
+
+The On Chip Peripherals (OCP) device node is a simplified
+representation of the AM33XX SoC interconnect. An OCP dev
+node is already defined in the am33xx.dtsi Device Tree
+source file included by am33xx based boards so there is
+no need to redefine this on each board DT file.
+
+Also, the OCP and IP modules directly connected to it are SoC
+internal details that is better to keep outside of board files.
+
+Signed-off-by: Javier Martinez Canillas <javier.martinez at collabora.co.uk>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 100 ++++----
+ arch/arm/boot/dts/am335x-evm.dts | 380 +++++++++++++++---------------
+ arch/arm/boot/dts/am335x-evmsk.dts | 148 ++++++------
+ 3 files changed, 311 insertions(+), 317 deletions(-)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index 29799ac..ff5c3ca 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -21,57 +21,6 @@
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+- ocp {
+- uart0: serial at 44e09000 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&uart0_pins>;
+-
+- status = "okay";
+- };
+-
+- musb: usb at 47400000 {
+- status = "okay";
+-
+- control at 44e10000 {
+- status = "okay";
+- };
+-
+- usb-phy at 47401300 {
+- status = "okay";
+- };
+-
+- usb-phy at 47401b00 {
+- status = "okay";
+- };
+-
+- usb at 47401000 {
+- status = "okay";
+- };
+-
+- usb at 47401800 {
+- status = "okay";
+- dr_mode = "host";
+- };
+-
+- dma-controller at 07402000 {
+- status = "okay";
+- };
+- };
+-
+- i2c0: i2c at 44e0b000 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&i2c0_pins>;
+-
+- status = "okay";
+- clock-frequency = <400000>;
+-
+- tps: tps at 24 {
+- reg = <0x24>;
+- };
+-
+- };
+- };
+-
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&user_leds_s0>;
+@@ -217,6 +166,55 @@
+ };
+ };
+
++&uart0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart0_pins>;
++
++ status = "okay";
++};
++
++&usb {
++ status = "okay";
++
++ control at 44e10000 {
++ status = "okay";
++ };
++
++ usb-phy at 47401300 {
++ status = "okay";
++ };
++
++ usb-phy at 47401b00 {
++ status = "okay";
++ };
++
++ usb at 47401000 {
++ status = "okay";
++ };
++
++ usb at 47401800 {
++ status = "okay";
++ dr_mode = "host";
++ };
++
++ dma-controller at 07402000 {
++ status = "okay";
++ };
++};
++
++&i2c0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c0_pins>;
++
++ status = "okay";
++ clock-frequency = <400000>;
++
++ tps: tps at 24 {
++ reg = <0x24>;
++ };
++
++};
++
+ /include/ "tps65217.dtsi"
+
+ &tps {
+diff --git a/arch/arm/boot/dts/am335x-evm.dts
b/arch/arm/boot/dts/am335x-evm.dts
+index 1525cd6..23b0a3e 100644
+--- a/arch/arm/boot/dts/am335x-evm.dts
++++ b/arch/arm/boot/dts/am335x-evm.dts
+@@ -24,197 +24,6 @@
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+- ocp {
+- uart0: serial at 44e09000 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&uart0_pins>;
+-
+- status = "okay";
+- };
+-
+- i2c0: i2c at 44e0b000 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&i2c0_pins>;
+-
+- status = "okay";
+- clock-frequency = <400000>;
+-
+- tps: tps at 2d {
+- reg = <0x2d>;
+- };
+- };
+-
+- musb: usb at 47400000 {
+- status = "okay";
+-
+- control at 44e10000 {
+- status = "okay";
+- };
+-
+- usb-phy at 47401300 {
+- status = "okay";
+- };
+-
+- usb-phy at 47401b00 {
+- status = "okay";
+- };
+-
+- usb at 47401000 {
+- status = "okay";
+- };
+-
+- usb at 47401800 {
+- status = "okay";
+- dr_mode = "host";
+- };
+-
+- dma-controller at 07402000 {
+- status = "okay";
+- };
+- };
+-
+- i2c1: i2c at 4802a000 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&i2c1_pins>;
+-
+- status = "okay";
+- clock-frequency = <100000>;
+-
+- lis331dlh: lis331dlh at 18 {
+- compatible = "st,lis331dlh", "st,lis3lv02d";
+- reg = <0x18>;
+- Vdd-supply = <&lis3_reg>;
+- Vdd_IO-supply = <&lis3_reg>;
+-
+- st,click-single-x;
+- st,click-single-y;
+- st,click-single-z;
+- st,click-thresh-x = <10>;
+- st,click-thresh-y = <10>;
+- st,click-thresh-z = <10>;
+- st,irq1-click;
+- st,irq2-click;
+- st,wakeup-x-lo;
+- st,wakeup-x-hi;
+- st,wakeup-y-lo;
+- st,wakeup-y-hi;
+- st,wakeup-z-lo;
+- st,wakeup-z-hi;
+- st,min-limit-x = <120>;
+- st,min-limit-y = <120>;
+- st,min-limit-z = <140>;
+- st,max-limit-x = <550>;
+- st,max-limit-y = <550>;
+- st,max-limit-z = <750>;
+- };
+-
+- tsl2550: tsl2550 at 39 {
+- compatible = "taos,tsl2550";
+- reg = <0x39>;
+- };
+-
+- tmp275: tmp275 at 48 {
+- compatible = "ti,tmp275";
+- reg = <0x48>;
+- };
+- };
+-
+- elm: elm at 48080000 {
+- status = "okay";
+- };
+-
+- epwmss0: epwmss at 48300000 {
+- status = "okay";
+-
+- ecap0: ecap at 48300100 {
+- status = "okay";
+- pinctrl-names = "default";
+- pinctrl-0 = <&ecap0_pins>;
+- };
+- };
+-
+- gpmc: gpmc at 50000000 {
+- status = "okay";
+- pinctrl-names = "default";
+- pinctrl-0 = <&nandflash_pins_s0>;
+- ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
+- nand at 0,0 {
+- reg = <0 0 0>; /* CS0, offset 0 */
+- nand-bus-width = <8>;
+- ti,nand-ecc-opt = "bch8";
+- gpmc,device-nand = "true";
+- gpmc,device-width = <1>;
+- gpmc,sync-clk-ps = <0>;
+- gpmc,cs-on-ns = <0>;
+- gpmc,cs-rd-off-ns = <44>;
+- gpmc,cs-wr-off-ns = <44>;
+- gpmc,adv-on-ns = <6>;
+- gpmc,adv-rd-off-ns = <34>;
+- gpmc,adv-wr-off-ns = <44>;
+- gpmc,we-on-ns = <0>;
+- gpmc,we-off-ns = <40>;
+- gpmc,oe-on-ns = <0>;
+- gpmc,oe-off-ns = <54>;
+- gpmc,access-ns = <64>;
+- gpmc,rd-cycle-ns = <82>;
+- gpmc,wr-cycle-ns = <82>;
+- gpmc,wait-on-read = "true";
+- gpmc,wait-on-write = "true";
+- gpmc,bus-turnaround-ns = <0>;
+- gpmc,cycle2cycle-delay-ns = <0>;
+- gpmc,clk-activation-ns = <0>;
+- gpmc,wait-monitoring-ns = <0>;
+- gpmc,wr-access-ns = <40>;
+- gpmc,wr-data-mux-bus-ns = <0>;
+-
+- #address-cells = <1>;
+- #size-cells = <1>;
+- elm_id = <&elm>;
+-
+- /* MTD partition table */
+- partition at 0 {
+- label = "SPL1";
+- reg = <0x00000000 0x000020000>;
+- };
+-
+- partition at 1 {
+- label = "SPL2";
+- reg = <0x00020000 0x00020000>;
+- };
+-
+- partition at 2 {
+- label = "SPL3";
+- reg = <0x00040000 0x00020000>;
+- };
+-
+- partition at 3 {
+- label = "SPL4";
+- reg = <0x00060000 0x00020000>;
+- };
+-
+- partition at 4 {
+- label = "U-boot";
+- reg = <0x00080000 0x001e0000>;
+- };
+-
+- partition at 5 {
+- label = "environment";
+- reg = <0x00260000 0x00020000>;
+- };
+-
+- partition at 6 {
+- label = "Kernel";
+- reg = <0x00280000 0x00500000>;
+- };
+-
+- partition at 7 {
+- label = "File-System";
+- reg = <0x00780000 0x0F880000>;
+- };
+- };
+- };
+- };
+-
+ vbat: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+@@ -405,6 +214,195 @@
+ };
+ };
+
++&uart0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart0_pins>;
++
++ status = "okay";
++};
++
++&i2c0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c0_pins>;
++
++ status = "okay";
++ clock-frequency = <400000>;
++
++ tps: tps at 2d {
++ reg = <0x2d>;
++ };
++};
++
++&usb {
++ status = "okay";
++
++ control at 44e10000 {
++ status = "okay";
++ };
++
++ usb-phy at 47401300 {
++ status = "okay";
++ };
++
++ usb-phy at 47401b00 {
++ status = "okay";
++ };
++
++ usb at 47401000 {
++ status = "okay";
++ };
++
++ usb at 47401800 {
++ status = "okay";
++ dr_mode = "host";
++ };
++
++ dma-controller at 07402000 {
++ status = "okay";
++ };
++};
++
++&i2c1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c1_pins>;
++
++ status = "okay";
++ clock-frequency = <100000>;
++
++ lis331dlh: lis331dlh at 18 {
++ compatible = "st,lis331dlh", "st,lis3lv02d";
++ reg = <0x18>;
++ Vdd-supply = <&lis3_reg>;
++ Vdd_IO-supply = <&lis3_reg>;
++
++ st,click-single-x;
++ st,click-single-y;
++ st,click-single-z;
++ st,click-thresh-x = <10>;
++ st,click-thresh-y = <10>;
++ st,click-thresh-z = <10>;
++ st,irq1-click;
++ st,irq2-click;
++ st,wakeup-x-lo;
++ st,wakeup-x-hi;
++ st,wakeup-y-lo;
++ st,wakeup-y-hi;
++ st,wakeup-z-lo;
++ st,wakeup-z-hi;
++ st,min-limit-x = <120>;
++ st,min-limit-y = <120>;
++ st,min-limit-z = <140>;
++ st,max-limit-x = <550>;
++ st,max-limit-y = <550>;
++ st,max-limit-z = <750>;
++ };
++
++ tsl2550: tsl2550 at 39 {
++ compatible = "taos,tsl2550";
++ reg = <0x39>;
++ };
++
++ tmp275: tmp275 at 48 {
++ compatible = "ti,tmp275";
++ reg = <0x48>;
++ };
++};
++
++&elm {
++ status = "okay";
++};
++
++&epwmss0 {
++ status = "okay";
++
++ ecap0: ecap at 48300100 {
++ status = "okay";
++ pinctrl-names = "default";
++ pinctrl-0 = <&ecap0_pins>;
++ };
++};
++
++&gpmc {
++ status = "okay";
++ pinctrl-names = "default";
++ pinctrl-0 = <&nandflash_pins_s0>;
++ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
++ nand at 0,0 {
++ reg = <0 0 0>; /* CS0, offset 0 */
++ nand-bus-width = <8>;
++ ti,nand-ecc-opt = "bch8";
++ gpmc,device-nand = "true";
++ gpmc,device-width = <1>;
++ gpmc,sync-clk-ps = <0>;
++ gpmc,cs-on-ns = <0>;
++ gpmc,cs-rd-off-ns = <44>;
++ gpmc,cs-wr-off-ns = <44>;
++ gpmc,adv-on-ns = <6>;
++ gpmc,adv-rd-off-ns = <34>;
++ gpmc,adv-wr-off-ns = <44>;
++ gpmc,we-on-ns = <0>;
++ gpmc,we-off-ns = <40>;
++ gpmc,oe-on-ns = <0>;
++ gpmc,oe-off-ns = <54>;
++ gpmc,access-ns = <64>;
++ gpmc,rd-cycle-ns = <82>;
++ gpmc,wr-cycle-ns = <82>;
++ gpmc,wait-on-read = "true";
++ gpmc,wait-on-write = "true";
++ gpmc,bus-turnaround-ns = <0>;
++ gpmc,cycle2cycle-delay-ns = <0>;
++ gpmc,clk-activation-ns = <0>;
++ gpmc,wait-monitoring-ns = <0>;
++ gpmc,wr-access-ns = <40>;
++ gpmc,wr-data-mux-bus-ns = <0>;
++
++ #address-cells = <1>;
++ #size-cells = <1>;
++ elm_id = <&elm>;
++
++ /* MTD partition table */
++ partition at 0 {
++ label = "SPL1";
++ reg = <0x00000000 0x000020000>;
++ };
++
++ partition at 1 {
++ label = "SPL2";
++ reg = <0x00020000 0x00020000>;
++ };
++
++ partition at 2 {
++ label = "SPL3";
++ reg = <0x00040000 0x00020000>;
++ };
++
++ partition at 3 {
++ label = "SPL4";
++ reg = <0x00060000 0x00020000>;
++ };
++
++ partition at 4 {
++ label = "U-boot";
++ reg = <0x00080000 0x001e0000>;
++ };
++
++ partition at 5 {
++ label = "environment";
++ reg = <0x00260000 0x00020000>;
++ };
++
++ partition at 6 {
++ label = "Kernel";
++ reg = <0x00280000 0x00500000>;
++ };
++
++ partition at 7 {
++ label = "File-System";
++ reg = <0x00780000 0x0F880000>;
++ };
++ };
++};
++
+ #include "tps65910.dtsi"
+
+ &tps {
+diff --git a/arch/arm/boot/dts/am335x-evmsk.dts
b/arch/arm/boot/dts/am335x-evmsk.dts
+index f0066fe..bc93895 100644
+--- a/arch/arm/boot/dts/am335x-evmsk.dts
++++ b/arch/arm/boot/dts/am335x-evmsk.dts
+@@ -31,81 +31,6 @@
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+- ocp {
+- uart0: serial at 44e09000 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&uart0_pins>;
+-
+- status = "okay";
+- };
+-
+- i2c0: i2c at 44e0b000 {
+- pinctrl-names = "default";
+- pinctrl-0 = <&i2c0_pins>;
+-
+- status = "okay";
+- clock-frequency = <400000>;
+-
+- tps: tps at 2d {
+- reg = <0x2d>;
+- };
+-
+- lis331dlh: lis331dlh at 18 {
+- compatible = "st,lis331dlh", "st,lis3lv02d";
+- reg = <0x18>;
+- Vdd-supply = <&lis3_reg>;
+- Vdd_IO-supply = <&lis3_reg>;
+-
+- st,click-single-x;
+- st,click-single-y;
+- st,click-single-z;
+- st,click-thresh-x = <10>;
+- st,click-thresh-y = <10>;
+- st,click-thresh-z = <10>;
+- st,irq1-click;
+- st,irq2-click;
+- st,wakeup-x-lo;
+- st,wakeup-x-hi;
+- st,wakeup-y-lo;
+- st,wakeup-y-hi;
+- st,wakeup-z-lo;
+- st,wakeup-z-hi;
+- st,min-limit-x = <120>;
+- st,min-limit-y = <120>;
+- st,min-limit-z = <140>;
+- st,max-limit-x = <550>;
+- st,max-limit-y = <550>;
+- st,max-limit-z = <750>;
+- };
+- };
+-
+- musb: usb at 47400000 {
+- status = "okay";
+-
+- control at 44e10000 {
+- status = "okay";
+- };
+-
+- usb-phy at 47401300 {
+- status = "okay";
+- };
+-
+- usb at 47401000 {
+- status = "okay";
+- };
+- };
+-
+- epwmss2: epwmss at 48304000 {
+- status = "okay";
+-
+- ecap2: ecap at 48304100 {
+- status = "okay";
+- pinctrl-names = "default";
+- pinctrl-0 = <&ecap2_pins>;
+- };
+- };
+- };
+-
+ vbat: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+@@ -321,6 +246,79 @@
+ };
+ };
+
++&uart0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart0_pins>;
++
++ status = "okay";
++};
++
++&i2c0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c0_pins>;
++
++ status = "okay";
++ clock-frequency = <400000>;
++
++ tps: tps at 2d {
++ reg = <0x2d>;
++ };
++
++ lis331dlh: lis331dlh at 18 {
++ compatible = "st,lis331dlh", "st,lis3lv02d";
++ reg = <0x18>;
++ Vdd-supply = <&lis3_reg>;
++ Vdd_IO-supply = <&lis3_reg>;
++
++ st,click-single-x;
++ st,click-single-y;
++ st,click-single-z;
++ st,click-thresh-x = <10>;
++ st,click-thresh-y = <10>;
++ st,click-thresh-z = <10>;
++ st,irq1-click;
++ st,irq2-click;
++ st,wakeup-x-lo;
++ st,wakeup-x-hi;
++ st,wakeup-y-lo;
++ st,wakeup-y-hi;
++ st,wakeup-z-lo;
++ st,wakeup-z-hi;
++ st,min-limit-x = <120>;
++ st,min-limit-y = <120>;
++ st,min-limit-z = <140>;
++ st,max-limit-x = <550>;
++ st,max-limit-y = <550>;
++ st,max-limit-z = <750>;
++ };
++};
++
++&usb {
++ status = "okay";
++
++ control at 44e10000 {
++ status = "okay";
++ };
++
++ usb-phy at 47401300 {
++ status = "okay";
++ };
++
++ usb at 47401000 {
++ status = "okay";
++ };
++};
++
++&epwmss2 {
++ status = "okay";
++
++ ecap2: ecap at 48304100 {
++ status = "okay";
++ pinctrl-names = "default";
++ pinctrl-0 = <&ecap2_pins>;
++ };
++};
++
+ #include "tps65910.dtsi"
+
+ &tps {
+--
+1.8.4.rc3
+
+From a9a966a91ca0304de63c03ef5131c08b1d19f60d Mon Sep 17 00:00:00 2001
+From: Dan Murphy <dmurphy at ti.com>
+Date: Wed, 2 Oct 2013 12:58:33 -0500
+Subject: [PATCH 12/15] ARM: dts: AM33XX: add ethernet alias's for am33xx
+
+Set the alias for ethernet0 and ethernet1 so that uBoot
+can set the MAC address appropriately.
+
+Currently u-boot cannot find the alias and there for does
+not set the MAC address.
+
+Signed-off-by: Dan Murphy <dmurphy at ti.com>
+Tested-by: Mugunthan V N <mugunthanvnm at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am33xx.dtsi | 2 ++
+ 1 file changed, 2 insertions(+)
+
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index 553adc6..8aabaa0 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -30,6 +30,8 @@
+ usb1 = &usb1;
+ phy0 = &usb0_phy;
+ phy1 = &usb1_phy;
++ ethernet0 = &cpsw_emac0;
++ ethernet1 = &cpsw_emac1;
+ };
+
+ cpus {
+--
+1.8.4.rc3
+
+From 5339e0ba31b312715a5542a53c6a46c3e9a5f53b Mon Sep 17 00:00:00 2001
+From: Nishanth Menon <nm at ti.com>
+Date: Mon, 30 Sep 2013 09:40:16 -0500
+Subject: [PATCH 13/15] ARM: dts: am335x-boneblack: move fixed regulator to
+ board level
+
+3.3V fixed regulator does not belong to TPS node - as a result
+the fixed regulator is never probed and MMC is continually deferred
+due to lack of regulator.
+
+Move the fixed regulator to be at root of platform.
+
+Cc: Joel Fernandes <joelf at ti.com>
+Cc: Sekhar Nori <nsekhar at ti.com>
+Cc: Koen Kooi <koen at dominion.thruhere.net>
+Signed-off-by: Nishanth Menon <nm at ti.com>
+Tested-by: Felipe Balbi <balbi at ti.com>
+Tested-by: Balaji T K <balajitk at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 14 +++++++-------
+ 1 file changed, 7 insertions(+), 7 deletions(-)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index ff5c3ca..b3e6fcf 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -55,6 +55,13 @@
+ default-state = "off";
+ };
+ };
++
++ vmmcsd_fixed: fixedregulator at 0 {
++ compatible = "regulator-fixed";
++ regulator-name = "vmmcsd_fixed";
++ regulator-min-microvolt = <3300000>;
++ regulator-max-microvolt = <3300000>;
++ };
+ };
+
+ &am33xx_pinmux {
+@@ -257,13 +264,6 @@
+ regulator-always-on;
+ };
+ };
+-
+- vmmcsd_fixed: fixedregulator at 0 {
+- compatible = "regulator-fixed";
+- regulator-name = "vmmcsd_fixed";
+- regulator-min-microvolt = <3300000>;
+- regulator-max-microvolt = <3300000>;
+- };
+ };
+
+ &cpsw_emac0 {
+--
+1.8.4.rc3
+
+From 085e4e139ae508aab69c568d6bf2a6860a0bd607 Mon Sep 17 00:00:00 2001
+From: Balaji T K <balajitk at ti.com>
+Date: Fri, 27 Sep 2013 17:05:09 +0530
+Subject: [PATCH 14/15] ARM: dts: am335x-bone-common: correct mux mode for cmd
+ line
+
+Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
+to detect eMMC on BBB and BBW + eMMC cape.
+
+Signed-off-by: Balaji T K <balajitk at ti.com>
+Tested-by: Felipe Balbi <balbi at ti.com>
+Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index b3e6fcf..e3f27ec 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -160,7 +160,7 @@
+ emmc_pins: pinmux_emmc_pins {
+ pinctrl-single,pins = <
+ 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+- 0x84 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_csn2.mmc1_cmd */
++ 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+ 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+ 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+ 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+--
+1.8.4.rc3
+
+commit d6cfc1e266d34d5b1f8a26bb272d2d2c466d89b8
+Author: Benoit Parrot <bparrot at ti.com>
+Date: Thu Aug 8 18:28:14 2013 -0500
+
+ ARM: dts: AM33XX: Add LCDC info into am335x-evm
+
+ Add LCDC device node in DT for am33xx
+ Add LCDC and Panel info in DT for am335x-evm
+
+ Changes:
+ - remove redundant/unnecessary SoC specific setting in the board dts
+ - resolved conflicts on for_3.13/dts
+
+ Signed-off-by: Benoit Parrot <bparrot at ti.com>
+ Signed-off-by: Joel Fernandes <joelf at ti.com>
+ Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+
+diff --git a/arch/arm/boot/dts/am335x-evm.dts
b/arch/arm/boot/dts/am335x-evm.dts
+index ff834ad..eabacf9 100644
+--- a/arch/arm/boot/dts/am335x-evm.dts
++++ b/arch/arm/boot/dts/am335x-evm.dts
+@@ -85,6 +85,40 @@
+ brightness-levels = <0 51 53 56 62 75 101 152 255>;
+ default-brightness-level = <8>;
+ };
++
++ panel {
++ compatible = "ti,tilcdc,panel";
++ status = "okay";
++ pinctrl-names = "default";
++ pinctrl-0 = <&lcd_pins_s0>;
++ panel-info {
++ ac-bias = <255>;
++ ac-bias-intrpt = <0>;
++ dma-burst-sz = <16>;
++ bpp = <32>;
++ fdd = <0x80>;
++ sync-edge = <0>;
++ sync-ctrl = <1>;
++ raster-order = <0>;
++ fifo-th = <0>;
++ };
++
++ display-timings {
++ 800x480p62 {
++ clock-frequency = <30000000>;
++ hactive = <800>;
++ vactive = <480>;
++ hfront-porch = <39>;
++ hback-porch = <39>;
++ hsync-len = <47>;
++ vback-porch = <29>;
++ vfront-porch = <13>;
++ vsync-len = <2>;
++ hsync-active = <1>;
++ vsync-active = <1>;
++ };
++ };
++ };
+ };
+
+ &am33xx_pinmux {
+@@ -212,6 +246,39 @@
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
++
++ lcd_pins_s0: lcd_pins_s0 {
++ pinctrl-single,pins = <
++ 0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
++ 0x24 0x01 /* gpmc_ad9.lcd_data17, OUTPUT | MODE1 */
++ 0x28 0x01 /* gpmc_ad10.lcd_data18, OUTPUT | MODE1 */
++ 0x2c 0x01 /* gpmc_ad11.lcd_data19, OUTPUT | MODE1 */
++ 0x30 0x01 /* gpmc_ad12.lcd_data20, OUTPUT | MODE1 */
++ 0x34 0x01 /* gpmc_ad13.lcd_data21, OUTPUT | MODE1 */
++ 0x38 0x01 /* gpmc_ad14.lcd_data22, OUTPUT | MODE1 */
++ 0x3c 0x01 /* gpmc_ad15.lcd_data23, OUTPUT | MODE1 */
++ 0xa0 0x00 /* lcd_data0.lcd_data0, OUTPUT | MODE0 */
++ 0xa4 0x00 /* lcd_data1.lcd_data1, OUTPUT | MODE0 */
++ 0xa8 0x00 /* lcd_data2.lcd_data2, OUTPUT | MODE0 */
++ 0xac 0x00 /* lcd_data3.lcd_data3, OUTPUT | MODE0 */
++ 0xb0 0x00 /* lcd_data4.lcd_data4, OUTPUT | MODE0 */
++ 0xb4 0x00 /* lcd_data5.lcd_data5, OUTPUT | MODE0 */
++ 0xb8 0x00 /* lcd_data6.lcd_data6, OUTPUT | MODE0 */
++ 0xbc 0x00 /* lcd_data7.lcd_data7, OUTPUT | MODE0 */
++ 0xc0 0x00 /* lcd_data8.lcd_data8, OUTPUT | MODE0 */
++ 0xc4 0x00 /* lcd_data9.lcd_data9, OUTPUT | MODE0 */
++ 0xc8 0x00 /* lcd_data10.lcd_data10, OUTPUT | MODE0 */
++ 0xcc 0x00 /* lcd_data11.lcd_data11, OUTPUT | MODE0 */
++ 0xd0 0x00 /* lcd_data12.lcd_data12, OUTPUT | MODE0 */
++ 0xd4 0x00 /* lcd_data13.lcd_data13, OUTPUT | MODE0 */
++ 0xd8 0x00 /* lcd_data14.lcd_data14, OUTPUT | MODE0 */
++ 0xdc 0x00 /* lcd_data15.lcd_data15, OUTPUT | MODE0 */
++ 0xe0 0x00 /* lcd_vsync.lcd_vsync, OUTPUT | MODE0 */
++ 0xe4 0x00 /* lcd_hsync.lcd_hsync, OUTPUT | MODE0 */
++ 0xe8 0x00 /* lcd_pclk.lcd_pclk, OUTPUT | MODE0 */
++ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
++ >;
++ };
+ };
+
+ &uart0 {
+@@ -308,6 +375,10 @@
+ };
+ };
+
++&lcdc {
++ status = "okay";
++};
++
+ &elm {
+ status = "okay";
+ };
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index c87bf4b..7db3c81 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -684,6 +684,15 @@
+ status = "disabled";
+ };
+
++ lcdc: lcdc at 4830e000 {
++ compatible = "ti,am33xx-tilcdc";
++ reg = <0x4830e000 0x1000>;
++ interrupt-parent = <&intc>;
++ interrupts = <36>;
++ ti,hwmods = "lcdc";
++ status = "disabled";
++ };
++
+ tscadc: tscadc at 44e0d000 {
+ compatible = "ti,am3359-tscadc";
+ reg = <0x44e0d000 0x1000>;
+commit 559a08e89350e269a4bba93629f39da5dd8e4fef
+Author: Darren Etheridge <detheridge at ti.com>
+Date: Fri Sep 20 15:01:42 2013 -0500
+
+ ARM: dts: AM33XX beagle black: add pinmux and hdmi node to enable display
+
+ Enable the hdmi output and the LCD Controller on BeagleBone
+ Black. Also configure the correct pinmux for output of
+ video data from the SoC to the HDMI encoder.
+
+ Signed-off-by: Darren Etheridge <detheridge at ti.com>
+ Signed-off-by: Joel Fernandes <joelf at ti.com>
+ Signed-off-by: Benoit Cousson <bcousson at baylibre.com>
+
+diff --git a/arch/arm/boot/dts/am335x-boneblack.dts
b/arch/arm/boot/dts/am335x-boneblack.dts
+index 16b3bea..6b71ad9 100644
+--- a/arch/arm/boot/dts/am335x-boneblack.dts
++++ b/arch/arm/boot/dts/am335x-boneblack.dts
+@@ -28,3 +28,51 @@
+ status = "okay";
+ ti,vcc-aux-disable-is-sleep;
+ };
++
++&am33xx_pinmux {
++ nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
++ pinctrl-single,pins = <
++ 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 |
AM33XX_PIN_OUTPUT */
++ 0xa0 0x08 /* lcd_data0.lcd_data0, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xa4 0x08 /* lcd_data1.lcd_data1, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xa8 0x08 /* lcd_data2.lcd_data2, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xac 0x08 /* lcd_data3.lcd_data3, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xb0 0x08 /* lcd_data4.lcd_data4, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xb4 0x08 /* lcd_data5.lcd_data5, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xb8 0x08 /* lcd_data6.lcd_data6, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xbc 0x08 /* lcd_data7.lcd_data7, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xc0 0x08 /* lcd_data8.lcd_data8, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xc4 0x08 /* lcd_data9.lcd_data9, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xc8 0x08 /* lcd_data10.lcd_data10, OMAP_MUX_MODE0
| AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xcc 0x08 /* lcd_data11.lcd_data11, OMAP_MUX_MODE0
| AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xd0 0x08 /* lcd_data12.lcd_data12, OMAP_MUX_MODE0
| AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xd4 0x08 /* lcd_data13.lcd_data13, OMAP_MUX_MODE0
| AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xd8 0x08 /* lcd_data14.lcd_data14, OMAP_MUX_MODE0
| AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xdc 0x08 /* lcd_data15.lcd_data15, OMAP_MUX_MODE0
| AM33XX_PIN_OUTPUT | AM33XX_PULL_DISA */
++ 0xe0 0x00 /* lcd_vsync.lcd_vsync, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT */
++ 0xe4 0x00 /* lcd_hsync.lcd_hsync, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT */
++ 0xe8 0x00 /* lcd_pclk.lcd_pclk, OMAP_MUX_MODE0 |
AM33XX_PIN_OUTPUT */
++ 0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en,
OMAP_MUX_MODE0 | AM33XX_PIN_OUTPUT */
++ >;
++ };
++ nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
++ pinctrl-single,pins = <
++ 0x1b0 0x03 /* xdma_event_intr0, OMAP_MUX_MODE3 |
AM33XX_PIN_OUTPUT */
++ >;
++ };
++};
++
++&lcdc {
++ status = "okay";
++};
++
++/ {
++ hdmi {
++ compatible = "ti,tilcdc,slave";
++ i2c = <&i2c0>;
++ pinctrl-names = "default", "off";
++ pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
++ pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
++ status = "okay";
++ };
++};
+commit d4cbe80db468dcfaa058f9f00a332784e5dff316
+Author: Suman Anna <s-anna at ti.com>
+Date: Thu Oct 10 16:15:35 2013 -0500
+
+ ARM: dts: AM33XX: Add hwspinlock node
+
+ Add the hwspinlock device tree node for AM33xx family
+ of SoCs.
+
+ Signed-off-by: Suman Anna <s-anna at ti.com>
+ Signed-off-by: Tony Lindgren <tony at atomide.com>
+
+diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
+index 0ca13ad..9ae258e 100644
+--- a/arch/arm/boot/dts/am33xx.dtsi
++++ b/arch/arm/boot/dts/am33xx.dtsi
+@@ -288,6 +288,12 @@
+ status = "disabled";
+ };
+
++ hwspinlock: spinlock at 480ca000 {
++ compatible = "ti,omap4-hwspinlock";
++ reg = <0x480ca000 0x1000>;
++ ti,hwmods = "spinlock";
++ };
++
+ wdt2: wdt at 44e35000 {
+ compatible = "ti,omap3-wdt";
+ ti,hwmods = "wd_timer2";
diff --git a/arm-am33xx-bblack.patch b/arm-am33xx-bblack.patch
new file mode 100644
index 0000000..4f62c9d
--- /dev/null
+++ b/arm-am33xx-bblack.patch
@@ -0,0 +1,610 @@
+Bugzilla: 1012025
+Upstream-status: In beagle github repository
https://github.com/beagleboard/kernel
+
+From 82fe302f565e00cfde3e96c6132df93b39525e7b Mon Sep 17 00:00:00 2001
+From: Philipp Zabel <p.zabel at pengutronix.de>
+Date: Tue, 28 May 2013 17:06:15 +0200
+Subject: [PATCH] reset: Add driver for gpio-controlled reset pins
+
+This driver implements a reset controller device that toggle a gpio
+connected to a reset pin of a peripheral IC. The delay between assertion
+and de-assertion of the reset signal can be configured via device tree.
+
+Signed-off-by: Philipp Zabel <p.zabel at pengutronix.de>
+Reviewed-by: Stephen Warren <swarren at nvidia.com>
+---
+ .../devicetree/bindings/reset/gpio-reset.txt | 35 +++++
+ drivers/reset/Kconfig | 11 ++
+ drivers/reset/Makefile | 1 +
+ drivers/reset/gpio-reset.c | 169 +++++++++++++++++++++
+ 4 files changed, 216 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/reset/gpio-reset.txt
+ create mode 100644 drivers/reset/gpio-reset.c
+
+diff --git a/Documentation/devicetree/bindings/reset/gpio-reset.txt
b/Documentation/devicetree/bindings/reset/gpio-reset.txt
+new file mode 100644
+index 0000000..bca5348
+--- /dev/null
++++ b/Documentation/devicetree/bindings/reset/gpio-reset.txt
+@@ -0,0 +1,35 @@
++GPIO reset controller
++=====================
++
++A GPIO reset controller controls a single GPIO that is connected to the reset
++pin of a peripheral IC. Please also refer to reset.txt in this directory for
++common reset controller binding usage.
++
++Required properties:
++- compatible: Should be "gpio-reset"
++- reset-gpios: A gpio used as reset line. The gpio specifier for this property
++ depends on the gpio controller that provides the gpio.
++- #reset-cells: 0, see below
++
++Optional properties:
++- reset-delay-us: delay in microseconds. The gpio reset line will be
asserted for
++ this duration to reset.
++- initially-in-reset: boolean. If not set, the initial state should be a
++ deasserted reset line. If this property exists, the
++ reset line should be kept in reset.
++
++example:
++
++sii902x_reset: gpio-reset {
++ compatible = "gpio-reset";
++ reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
++ reset-delay-us = <10000>;
++ initially-in-reset;
++ #reset-cells = <0>;
++};
++
++/* Device with nRESET pin connected to GPIO5_0 */
++sii902x at 39 {
++ /* ... */
++ resets = <&sii902x_reset>; /* active-low GPIO5_0, 10 ms delay */
++};
+diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
+index c9d04f7..1a862df 100644
+--- a/drivers/reset/Kconfig
++++ b/drivers/reset/Kconfig
+@@ -11,3 +11,14 @@ menuconfig RESET_CONTROLLER
+ via GPIOs or SoC-internal reset controller modules.
+
+ If unsure, say no.
++
++if RESET_CONTROLLER
++
++config RESET_GPIO
++ tristate "GPIO reset controller support"
++ depends on GPIOLIB && OF
++ help
++ This driver provides support for reset lines that are controlled
++ directly by GPIOs.
++
++endif
+diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
+index 1e2d83f..b854f20 100644
+--- a/drivers/reset/Makefile
++++ b/drivers/reset/Makefile
+@@ -1 +1,2 @@
+ obj-$(CONFIG_RESET_CONTROLLER) += core.o
++obj-$(CONFIG_RESET_GPIO) += gpio-reset.o
+diff --git a/drivers/reset/gpio-reset.c b/drivers/reset/gpio-reset.c
+new file mode 100644
+index 0000000..acc1076
+--- /dev/null
++++ b/drivers/reset/gpio-reset.c
+@@ -0,0 +1,169 @@
++/*
++ * GPIO Reset Controller driver
++ *
++ * Copyright 2013 Philipp Zabel, Pengutronix
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ */
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/gpio.h>
++#include <linux/module.h>
++#include <linux/of_gpio.h>
++#include <linux/platform_device.h>
++#include <linux/reset-controller.h>
++
++struct gpio_reset_data {
++ struct reset_controller_dev rcdev;
++ unsigned int gpio;
++ bool active_low;
++ u32 delay_us;
++};
++
++static void __gpio_reset_set(struct reset_controller_dev *rcdev, int asserted)
++{
++ struct gpio_reset_data *drvdata = container_of(rcdev,
++ struct gpio_reset_data, rcdev);
++ int value = asserted;
++
++ if (drvdata->active_low)
++ value = !value;
++
++ gpio_set_value(drvdata->gpio, value);
++}
++
++static int gpio_reset(struct reset_controller_dev *rcdev, unsigned long id)
++{
++ struct gpio_reset_data *drvdata = container_of(rcdev,
++ struct gpio_reset_data, rcdev);
++
++ if (drvdata->delay_us < 0)
++ return -ENOSYS;
++
++ __gpio_reset_set(rcdev, 1);
++ udelay(drvdata->delay_us);
++ __gpio_reset_set(rcdev, 0);
++
++ return 0;
++}
++
++static int gpio_reset_assert(struct reset_controller_dev *rcdev,
++ unsigned long id)
++{
++ __gpio_reset_set(rcdev, 1);
++
++ return 0;
++}
++
++static int gpio_reset_deassert(struct reset_controller_dev *rcdev,
++ unsigned long id)
++{
++ __gpio_reset_set(rcdev, 0);
++
++ return 0;
++}
++
++static struct reset_control_ops gpio_reset_ops = {
++ .reset = gpio_reset,
++ .assert = gpio_reset_assert,
++ .deassert = gpio_reset_deassert,
++};
++
++static int of_gpio_reset_xlate(struct reset_controller_dev *rcdev,
++ const struct of_phandle_args *reset_spec)
++{
++ if (WARN_ON(reset_spec->args_count != 0))
++ return -EINVAL;
++
++ return 0;
++}
++
++static int gpio_reset_probe(struct platform_device *pdev)
++{
++ struct device_node *np = pdev->dev.of_node;
++ struct gpio_reset_data *drvdata;
++ enum of_gpio_flags flags;
++ unsigned long gpio_flags;
++ bool initially_in_reset;
++ int ret;
++
++ drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
++ if (drvdata == NULL)
++ return -ENOMEM;
++
++ if (of_gpio_named_count(np, "reset-gpios") != 1)
++ return -EINVAL;
++
++ drvdata->gpio = of_get_named_gpio_flags(np, "reset-gpios", 0, &flags);
++ if (drvdata->gpio == -EPROBE_DEFER) {
++ return drvdata->gpio;
++ } else if (!gpio_is_valid(drvdata->gpio)) {
++ dev_err(&pdev->dev, "invalid reset gpio: %d\n", drvdata->gpio);
++ return drvdata->gpio;
++ }
++
++ drvdata->active_low = flags & OF_GPIO_ACTIVE_LOW;
++
++ ret = of_property_read_u32(np, "reset-delay-us", &drvdata->delay_us);
++ if (ret < 0)
++ return ret;
++
++ initially_in_reset = of_property_read_bool(np, "initially-in-reset");
++ if (drvdata->active_low ^ initially_in_reset)
++ gpio_flags = GPIOF_OUT_INIT_HIGH;
++ else
++ gpio_flags = GPIOF_OUT_INIT_LOW;
++
++ ret = devm_gpio_request_one(&pdev->dev, drvdata->gpio, gpio_flags, NULL);
++ if (ret < 0) {
++ dev_err(&pdev->dev, "failed to request gpio %d: %d\n",
++ drvdata->gpio, ret);
++ return ret;
++ }
++
++ drvdata->rcdev.of_node = np;
++ drvdata->rcdev.owner = THIS_MODULE;
++ drvdata->rcdev.nr_resets = 1;
++ drvdata->rcdev.ops = &gpio_reset_ops;
++ drvdata->rcdev.of_xlate = of_gpio_reset_xlate;
++ reset_controller_register(&drvdata->rcdev);
++
++ platform_set_drvdata(pdev, drvdata);
++
++ return 0;
++}
++
++static int gpio_reset_remove(struct platform_device *pdev)
++{
++ struct gpio_reset_data *drvdata = platform_get_drvdata(pdev);
++
++ reset_controller_unregister(&drvdata->rcdev);
++
++ return 0;
++}
++
++static struct of_device_id gpio_reset_dt_ids[] = {
++ { .compatible = "gpio-reset" },
++ { }
++};
++
++static struct platform_driver gpio_reset_driver = {
++ .probe = gpio_reset_probe,
++ .remove = gpio_reset_remove,
++ .driver = {
++ .name = "gpio-reset",
++ .owner = THIS_MODULE,
++ .of_match_table = of_match_ptr(gpio_reset_dt_ids),
++ },
++};
++
++module_platform_driver(gpio_reset_driver);
++
++MODULE_AUTHOR("Philipp Zabel <p.zabel at pengutronix.de>");
++MODULE_DESCRIPTION("gpio reset controller");
++MODULE_LICENSE("GPL");
++MODULE_ALIAS("platform:gpio-reset");
++MODULE_DEVICE_TABLE(of, gpio_reset_dt_ids);
+--
+1.8.2.1
+
+From 03664ac63b20b55af9522449bbad048476d259d5 Mon Sep 17 00:00:00 2001
+From: Joel Fernandes <joelf at ti.com>
+Date: Wed, 3 Jul 2013 17:29:44 -0500
+Subject: [PATCH 2/2] sound: soc: soc-dmaengine-pcm: Add support for new
+ DMAEngine request API
+
+Formerly these resources were coming HWMOD on OMAP-like SoCs. With the
+impending removal of HWMOD data, drivers are being converted to use the
+"of-dma" method of requesting DMA channels which from DT and can be obtained
+using the dma_request_slave_channel API. Add support to the soc-dmaengine-pcm
+helpers so that we can fetch and open channels using this method.
+
+Signed-off-by: Joel Fernandes <joelf at ti.com>
+---
+ sound/core/pcm_dmaengine.c | 22 ++++++++++++++++++++++
+ 1 file changed, 22 insertions(+)
+
+diff --git a/sound/core/pcm_dmaengine.c b/sound/core/pcm_dmaengine.c
+index aa924d9..461fe4f 100644
+--- a/sound/core/pcm_dmaengine.c
++++ b/sound/core/pcm_dmaengine.c
+@@ -276,6 +276,16 @@ struct dma_chan
*snd_dmaengine_pcm_request_channel(dma_filter_fn filter_fn,
+ }
+ EXPORT_SYMBOL_GPL(snd_dmaengine_pcm_request_channel);
+
++struct dma_chan *snd_dmaengine_pcm_request_slave_channel(
++ struct snd_pcm_substream *substream, char *name)
++{
++ struct snd_soc_pcm_runtime *rtd = substream->private_data;
++ struct device *dev = snd_soc_dai_get_drvdata(rtd->cpu_dai);
++
++ return dma_request_slave_channel(dev, name);
++}
++EXPORT_SYMBOL_GPL(snd_dmaengine_pcm_request_slave_channel);
++
+ /**
+ * snd_dmaengine_pcm_open - Open a dmaengine based PCM substream
+ * @substream: PCM substream
+@@ -334,6 +344,18 @@ int snd_dmaengine_pcm_open_request_chan(struct
snd_pcm_substream *substream,
+ }
+ EXPORT_SYMBOL_GPL(snd_dmaengine_pcm_open_request_chan);
+
++int snd_dmaengine_pcm_open_request_slave_chan(struct
snd_pcm_substream *substream, char *name)
++{
++ if(substream->stream == SNDRV_PCM_STREAM_PLAYBACK) {
++ return snd_dmaengine_pcm_open(substream,
++ snd_dmaengine_pcm_request_slave_channel(substream, "tx"));
++ } else {
++ return snd_dmaengine_pcm_open(substream,
++ snd_dmaengine_pcm_request_slave_channel(substream, "rx"));
++ }
++}
++EXPORT_SYMBOL_GPL(snd_dmaengine_pcm_open_request_slave_chan);
++
+ /**
+ * snd_dmaengine_pcm_close - Close a dmaengine based PCM substream
+ * @substream: PCM substream
+--
+1.8.4.rc3
+
+From ae38683badc8c80b29ccc8aa4e059f900b603551 Mon Sep 17 00:00:00 2001
+From: Pantelis Antoniou <panto at antoniou-consulting.com>
+Date: Fri, 26 Oct 2012 15:48:00 +0300
+Subject: [PATCH 1/2] omap-hsmmc: Correct usage of of_find_node_by_name
+
+of_find_node_by_name expect to have the parent node reference taken.
+---
+ drivers/mmc/host/omap_hsmmc.c | 10 ++++++++++
+ 1 file changed, 10 insertions(+)
+
+diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
+index 6ac63df..f5b660c 100644
+--- a/drivers/mmc/host/omap_hsmmc.c
++++ b/drivers/mmc/host/omap_hsmmc.c
+@@ -1893,6 +1893,16 @@ static int omap_hsmmc_probe(struct
platform_device *pdev)
+ * as we want. */
+ mmc->max_segs = 1024;
+
++ /* Eventually we should get our max_segs limitation for EDMA by
++ * querying the dmaengine API */
++ if (pdev->dev.of_node) {
++ struct device_node *parent = of_node_get(pdev->dev.of_node->parent);
++ struct device_node *node;
++ node = of_find_node_by_name(parent, "edma");
++ if (node)
++ mmc->max_segs = 16;
++ }
++
+ mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
+ mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
+ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+--
+1.8.2.1
+
+From 5d93a65cfc4ff6aaf78ab49f71daa2a644ea2ace Mon Sep 17 00:00:00 2001
+From: Pantelis Antoniou <panto at antoniou-consulting.com>
+Date: Fri, 30 Nov 2012 12:18:16 +0200
+Subject: [PATCH 2/2] omap_hsmmc: Add reset gpio
+
+Add a gpio property for controlling reset of the mmc device.
+eMMC on the beaglebone black requires it.
+
+Signed-off-by: Pantelis Antoniou <panto at antoniou-consulting.com>
+---
+ drivers/mmc/host/omap_hsmmc.c | 40 +++++++++++++++++++++++++++++++++-
+ include/linux/platform_data/mmc-omap.h | 3 +++
+ 2 files changed, 42 insertions(+), 1 deletion(-)
+
+diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
+index f5b660c..1bdb90f 100644
+--- a/drivers/mmc/host/omap_hsmmc.c
++++ b/drivers/mmc/host/omap_hsmmc.c
+@@ -41,6 +41,8 @@
+ #include <linux/pinctrl/consumer.h>
+ #include <linux/pm_runtime.h>
+ #include <linux/platform_data/mmc-omap.h>
++#include <linux/pinctrl/consumer.h>
++#include <linux/err.h>
+
+ /* OMAP HSMMC Host Controller Registers */
+ #define OMAP_HSMMC_SYSSTATUS 0x0014
+@@ -392,6 +394,7 @@ static inline int omap_hsmmc_have_reg(void)
+ static int omap_hsmmc_gpio_init(struct omap_mmc_platform_data *pdata)
+ {
+ int ret;
++ unsigned long flags;
+
+ if (gpio_is_valid(pdata->slots[0].switch_pin)) {
+ if (pdata->slots[0].cover)
+@@ -421,6 +424,24 @@ static int omap_hsmmc_gpio_init(struct
omap_mmc_platform_data *pdata)
+ } else
+ pdata->slots[0].gpio_wp = -EINVAL;
+
++ if (gpio_is_valid(pdata->slots[0].gpio_reset)) {
++ flags = pdata->slots[0].gpio_reset_active_low ?
++ GPIOF_OUT_INIT_LOW : GPIOF_OUT_INIT_HIGH;
++ ret = gpio_request_one(pdata->slots[0].gpio_reset, flags,
++ "mmc_reset");
++ if (ret)
++ goto err_free_wp;
++
++ /* hold reset */
++ udelay(pdata->slots[0].gpio_reset_hold_us);
++
++ gpio_set_value(pdata->slots[0].gpio_reset,
++ !pdata->slots[0].gpio_reset_active_low);
++
++ } else
++ pdata->slots[0].gpio_reset = -EINVAL;
++
++
+ return 0;
+
+ err_free_wp:
+@@ -434,6 +455,8 @@ err_free_sp:
+
+ static void omap_hsmmc_gpio_free(struct omap_mmc_platform_data *pdata)
+ {
++ if (gpio_is_valid(pdata->slots[0].gpio_reset))
++ gpio_free(pdata->slots[0].gpio_reset);
+ if (gpio_is_valid(pdata->slots[0].gpio_wp))
+ gpio_free(pdata->slots[0].gpio_wp);
+ if (gpio_is_valid(pdata->slots[0].switch_pin))
+@@ -788,7 +811,7 @@ omap_hsmmc_start_command(struct omap_hsmmc_host
*host, struct mmc_command *cmd,
+ * ac, bc, adtc, bcr. Only commands ending an open ended transfer need
+ * a val of 0x3, rest 0x0.
+ */
+- if (cmd == host->mrq->stop)
++ if (host->mrq && cmd == host->mrq->stop)
+ cmdtype = 0x3;
+
+ cmdreg = (cmd->opcode << 24) | (resptype << 16) | (cmdtype << 22);
+@@ -830,6 +853,8 @@ static void omap_hsmmc_request_done(struct
omap_hsmmc_host *host, struct mmc_req
+ int dma_ch;
+ unsigned long flags;
+
++ BUG_ON(mrq == NULL);
++
+ spin_lock_irqsave(&host->irq_lock, flags);
+ host->req_in_progress = 0;
+ dma_ch = host->dma_ch;
+@@ -1720,6 +1745,7 @@ static struct omap_mmc_platform_data
*of_get_hsmmc_pdata(struct device *dev)
+ struct device_node *np = dev->of_node;
+ u32 bus_width, max_freq;
+ int cd_gpio, wp_gpio;
++ enum of_gpio_flags reset_flags;
+
+ cd_gpio = of_get_named_gpio(np, "cd-gpios", 0);
+ wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
+@@ -1737,6 +1763,14 @@ static struct omap_mmc_platform_data
*of_get_hsmmc_pdata(struct device *dev)
+ pdata->nr_slots = 1;
+ pdata->slots[0].switch_pin = cd_gpio;
+ pdata->slots[0].gpio_wp = wp_gpio;
++ reset_flags = 0;
++ pdata->slots[0].gpio_reset = of_get_named_gpio_flags(np,
++ "reset-gpios", 0, &reset_flags);
++ pdata->slots[0].gpio_reset_active_low =
++ (reset_flags & OF_GPIO_ACTIVE_LOW) != 0;
++ pdata->slots[0].gpio_reset_hold_us = 100; /* default */
++ of_property_read_u32(np, "reset-gpio-hold-us",
++ &pdata->slots[0].gpio_reset_hold_us);
+
+ if (of_find_property(np, "ti,non-removable", NULL)) {
+ pdata->slots[0].nonremovable = true;
+@@ -1802,6 +1836,10 @@ static int omap_hsmmc_probe(struct
platform_device *pdev)
+ return -ENXIO;
+ }
+
++ pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
++ if (IS_ERR(pinctrl))
++ dev_warn(&pdev->dev, "unable to select pin group\n");
++
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(pdev, 0);
+ if (res == NULL || irq < 0)
+diff --git a/include/linux/platform_data/mmc-omap.h
b/include/linux/platform_data/mmc-omap.h
+index 2bf1b30..d548994 100644
+--- a/include/linux/platform_data/mmc-omap.h
++++ b/include/linux/platform_data/mmc-omap.h
+@@ -115,6 +115,9 @@ struct omap_mmc_platform_data {
+
+ int switch_pin; /* gpio (card detect) */
+ int gpio_wp; /* gpio (write protect) */
++ int gpio_reset; /* gpio (reset) */
++ int gpio_reset_active_low; /* 1 if reset is active low */
++ u32 gpio_reset_hold_us; /* time to hold in us */
+
+ int (*set_bus_mode)(struct device *dev, int slot, int bus_mode);
+ int (*set_power)(struct device *dev, int slot,
+--
+1.8.2.1
+
+From b45e4df71f07f2178db133db540e3f15e0b4ec05 Mon Sep 17 00:00:00 2001
+From: Pantelis Antoniou <panto at antoniou-consulting.com>
+Date: Sat, 15 Sep 2012 12:00:41 +0300
+Subject: [PATCH] pinctrl: pinctrl-single must be initialized early.
+
+When using pinctrl-single to handle i2c initialization, it has
+to be done early. Whether this is the best way to do so, is an
+exercise left to the reader.
+---
+ drivers/pinctrl/pinctrl-single.c | 12 +++++++++++-
+ 1 file changed, 11 insertions(+), 1 deletion(-)
+
+diff --git a/drivers/pinctrl/pinctrl-single.c
b/drivers/pinctrl/pinctrl-single.c
+index a82ace4..aeef35d 100644
+--- a/drivers/pinctrl/pinctrl-single.c
++++ b/drivers/pinctrl/pinctrl-single.c
+@@ -1673,7 +1673,17 @@ static struct platform_driver pcs_driver = {
+ #endif
+ };
+
+-module_platform_driver(pcs_driver);
++static int __init pcs_init(void)
++{
++ return platform_driver_register(&pcs_driver);
++}
++postcore_initcall(pcs_init);
++
++static void __exit pcs_exit(void)
++{
++ platform_driver_unregister(&pcs_driver);
++}
++module_exit(pcs_exit);
+
+ MODULE_AUTHOR("Tony Lindgren <tony at atomide.com>");
+ MODULE_DESCRIPTION("One-register-per-pin type device tree based
pinctrl driver");
+--
+1.8.2.1
+
+From e5e7abd2de7d8d4c74b5a1ccc6d47988250bd17d Mon Sep 17 00:00:00 2001
+From: Pantelis Antoniou <panto at antoniou-consulting.com>
+Date: Fri, 28 Jun 2013 18:39:55 +0300
+Subject: [PATCH 1/4] dts: beaglebone: Add I2C definitions for EEPROMs & capes
+
+Add the I2C definitions for the EEPROM devices on the baseboard
+and on the possibly connected capes.
+
+Signed-off-by: Pantelis Antoniou <panto at antoniou-consulting.com>
+---
+ arch/arm/boot/dts/am335x-bone-common.dtsi | 39 +++++++++++++++++++++++++++++++
+ 1 file changed, 39 insertions(+)
+
+diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi
b/arch/arm/boot/dts/am335x-bone-common.dtsi
+index e3f27ec..2d12775 100644
+--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
++++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
+@@ -84,6 +84,13 @@
+ >;
+ };
+
++ i2c2_pins: pinmux_i2c2_pins {
++ pinctrl-single,pins = <
++ 0x178 0x73 /* uart1_ctsn.i2c2_sda, SLEWCTRL_SLOW |
INPUT_PULLUP | MODE3 */
++ 0x17c 0x73 /* uart1_rtsn.i2c2_scl, SLEWCTRL_SLOW |
INPUT_PULLUP | MODE3 */
++ >;
++ };
++
+ uart0_pins: pinmux_uart0_pins {
+ pinctrl-single,pins = <
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */
+@@ -220,6 +227,38 @@
+ reg = <0x24>;
+ };
+
++ baseboard_eeprom: baseboard_eeprom at 50 {
++ compatible = "at,24c256";
++ reg = <0x50>;
++ };
++};
++
++&i2c2 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c2_pins>;
++
++ status = "okay";
++ clock-frequency = <100000>;
++
++ cape_eeprom0: cape_eeprom0 at 54 {
++ compatible = "at,24c256";
++ reg = <0x54>;
++ };
++
++ cape_eeprom1: cape_eeprom1 at 55 {
++ compatible = "at,24c256";
++ reg = <0x55>;
++ };
++
++ cape_eeprom2: cape_eeprom2 at 56 {
++ compatible = "at,24c256";
++ reg = <0x56>;
++ };
++
++ cape_eeprom3: cape_eeprom3 at 57 {
++ compatible = "at,24c256";
++ reg = <0x57>;
++ };
+ };
+
+ /include/ "tps65217.dtsi"
+--
+1.8.4.rc3
diff --git a/config-armv7 b/config-armv7
index b964812..910f749 100644
--- a/config-armv7
+++ b/config-armv7
@@ -304,7 +304,6 @@ CONFIG_SOC_AM43XX=y
CONFIG_AM335X_CONTROL_USB=m
CONFIG_AM335X_PHY_USB=m
CONFIG_USB_MUSB_AM335X_CHILD=y
-CONFIG_USB_TI_CPPI41_DMA=y
CONFIG_MFD_TI_AM335X_TSCADC=m
CONFIG_TI_ST=m
CONFIG_TI_DAC7512=m
@@ -319,7 +318,9 @@ CONFIG_SPI_DAVINCI=m
CONFIG_REGULATOR_TI_ABB=m
CONFIG_TI_PRIV_EDMA=y
CONFIG_TI_EDMA=y
-CONFIG_TI_CPPI41=m
+# Terribly unstable so disable for now
+# CONFIG_USB_TI_CPPI41_DMA is not set
+# CONFIG_TI_CPPI41 is not set
CONFIG_MFD_TI_AM335X_TSCADC=m
CONFIG_CHARGER_BQ24190=m
CONFIG_TI_ADC081C=m
diff --git a/kernel.spec b/kernel.spec
index 65c045e..590a7fe 100644
--- a/kernel.spec
+++ b/kernel.spec
@@ -686,7 +686,14 @@ Patch21020: arm-tegra-usb-no-reset-linux33.patch
# ARM i.MX6
# http://www.spinics.net/lists/devicetree/msg08276.html
-Patch21030: arm-imx6-utilite.patch
+Patch21025: arm-imx6-utilite.patch
+
+# am33xx (BeagleBone)
+# https://github.com/beagleboard/kernel
+# Pulled primarily from the above git repo. First patch is all in arm-soc
+# scheduled for 3.13. The others should be landing via other trees
+Patch21030: arm-am33xx-arm-soc-upstream.patch
+Patch21031: arm-am33xx-bblack.patch
#rhbz 754518
Patch21235: scsi-sd_revalidate_disk-prevent-NULL-ptr-deref.patch
@@ -1320,6 +1327,9 @@ ApplyPatch arm-omap-load-tfp410.patch
ApplyPatch arm-tegra-usb-no-reset-linux33.patch
ApplyPatch arm-imx6-utilite.patch
+ApplyPatch arm-am33xx-arm-soc-upstream.patch
+ApplyPatch arm-am33xx-bblack.patch
+
#
# bugfixes to drivers and filesystems
#
@@ -2301,6 +2311,9 @@ fi
# ||----w |
# || ||
%changelog
+* Sun Dec 1 2013 Peter Robinson <pbrobinson at fedoraproject.org>
+- Add patch set for AM33xx BeagleBones
+
* Sat Nov 30 2013 Josh Boyer <jwboyer at fedoraproject.org>
- Fix mdadm soft lockup and crash (rhbz 1033971)
- CVE-2013-6405 net: leak of uninited mem to userspace via recv
syscalls (rhbz 1035875 1035887)
--
1.8.4.2
More information about the kernel
mailing list