After I get the ipw2200 up...

[Justin Conover]

On 1/17/06, Alexander Sukhodolsky <umdsasha at gmail.com> wrote:
>
> Looks like a little troubleshooting has determined there's nothing wrong
> with the setup--I disabled the key and it works!  But the last thing I want
> is an unsecured wireless connection.  Basically, I have a WEP 64-bit hex key
> for my wireless net. Any ideas?
>
> Thanks,
> Alex
>
> PS Thanks for the help



Is your wireless router have the WEP setup correctly and turned on?


On 1/17/06, Alexander Sukhodolsky <umdsasha at gmail.com> wrote:
> >
> > not really sure--but my eth0 (wired ethernet) is disconnected anyway.  I
> > tried to down eth0 and eth1 and the up eth1, but with no luck.
> >
> > Alex
> >
> > On 1/17/06, Justin Conover <justin.conover at gmail.com> wrote:
> > >
> > >
> > >
> > > On 1/17/06, Alexander Sukhodolsky < umdsasha at gmail.com> wrote:
> > > >
> > > > I wish I could tell you it worked, but even though I followed what
> > > > you said and created wireless.sh and so on, still nothing--it runs
> > > > and shows up in iwconfig as connected to that, but still can't ping.  Also,
> > > > just for info, Network Configuration gets stuck on trying to get IP and then
> > > > says it's unable to connect--any ideas?
> > > >
> > > > Thanks,
> > > > Alex
> > >
> > >
> > >
> > > Does ifconfig eth1 get an ip?  Does eth0 still have an ip too?  If
> > > both of those are true, you might disable eth0
> > >
> > > /sbin/ifconfig eth0 down
> > >
> > > On 1/17/06, Justin Conover < justin.conover at gmail.com> wrote:
> > > > >
> > > > >
> > > > >
> > > > > On 1/17/06, Justin Conover < justin.conover at gmail.com> wrote:
> > > > > >
> > > > > >
> > > > > >
> > > > > > On 1/17/06, Alexander Sukhodolsky < umdsasha at gmail.com> wrote:
> > > > > > >
> > > > > > > So I followed Justin Conover's ipw2200 how-to (very easy) and
> > > > > > > got my
> > > > > > > wireless adapter to be recognized under the new fc5 test2 (i
> > > > > > > used the
> > > > > > > newest firmware, though).  But now I'm having problems
> > > > > > > actually
> > > > > > > connecting.  Basically, I went with what I know--kwifimanager
> > > > > > > and also
> > > > > > > system-config-network.  The system-config-network shows my
> > > > > > > wireless card
> > > > > > > and I try to set up a connection but nothing.  Now with
> > > > > > > kwifimanager, it
> > > > > > > shows all the ssid's of networks around and I set up in the
> > > > > > > configuration my network, and its corresponding password, and
> > > > > > > it does
> > > > > > > connect, but firefox shows nothing.  Any ideas?
> > > > > > >
> > > > > > > Also--I tried networkmanager, including running the services
> > > > > > > (serviceconf) and running it, but to no avail--/usr/bin doesnt
> > > > > > > seem to
> > > > > > > have NetworkManagerInfo or something.  Any ideas?  Anyone else
> > > > > > > have
> > > > > > > these problems in the new fc5 test2?
> > > > > > >
> > > > > > > Thanks,
> > > > > > > Alex
> > > > > > >
> > > > > > > --
> > > > > > > fedora-test-list mailing list
> > > > > > > fedora-test-list at redhat.com
> > > > > > > To unsubscribe:
> > > > > > > https://www.redhat.com/mailman/listinfo/fedora-test-list
> > > > > >
> > > > > >
> > > > > >
> > > > > > If you see the device from /sbin/iwconfig
> > > > > >
> > > > > > /sbin/iwconfig
> > > > > > lo        no wireless extensions.
> > > > > >
> > > > > > eth0      no wireless extensions.
> > > > > >
> > > > > > eth1      unassociated  ESSID:off/any
> > > > > >           Mode:Managed  Channel=0  Access Point:
> > > > > > 00:00:00:00:00:00
> > > > > >           Bit Rate=0 kb/s   Tx-Power=20 dBm
> > > > > >           Retry limit:7   RTS thr:off   Fragment thr:off
> > > > > >           Power Management:off
> > > > > >           Link Quality:0  Signal level:0  Noise level:0
> > > > > >           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid
> > > > > > frag:0
> > > > > >           Tx excessive retries:0  Invalid misc:0   Missed
> > > > > > beacon:0
> > > > > >
> > > > > > For example I just have a little script in my users $HOME
> > > > > >
> > > > > > $ cat wireless.sh
> > > > > > #!/bin/bash
> > > > > > /bin/su -c "/sbin/iwconfig eth1 essid YOURACCESSPOINT key
> > > > > > YOURKEY && /sbin/dhclient eth1 && /sbin/ifconfig eth1"
> > > > > >
> > > > > > just chmod +x and sh wireless.sh as your user and should be up.
> > > > > >
> > > > >
> > > > >
> > > > > Just realized I should test out NetworkManager when I get home
> > > > > tonight :)
> > > > >
> > > > >
> > > > >
> > > >
> > >
> >
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.fedoraproject.org/pipermail/test/attachments/20060117/34a2e99e/attachment.html