devel install woes (was FC6 T3 install woes)

[Jay Cliburn]

listman wrote:
[snip]
> <6>ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> <6>ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
> <6>ata1.00: ata1: dev 0 multi count 16
> <6>ata1.00: configured for UDMA/133
> <6>scsi1 : sata_nv
> <7>PM: Adding info for No Bus:host1
> <6>ata2: SATA link down (SStatus 0 SControl 300)
> <7>PM: Adding info for No Bus:target0:0:0
> <5>  Vendor: ATA       Model: ST3250620AS       Rev: 3.AA
> <5>  Type:   Direct-Access                      ANSI SCSI revision: 05
> <7>PM: Adding info for scsi:0:0:0:0
> <5>SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
> <5>sda: Write Protect is off
> <7>sda: Mode Sense: 00 3a 00 00
> <5>SCSI device sda: drive cache: write back
> <5>SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
> <5>sda: Write Protect is off
> <7>sda: Mode Sense: 00 3a 00 00
> <5>SCSI device sda: drive cache: write back
> <6> sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
> <5>sd 0:0:0:0: Attached scsi disk sda
[snip]
> <6>md: raid0 personality registered for level 0
> <6>md: raid1 personality registered for level 1
> <6>raid5: automatically using best checksumming function: generic_sse
> <4>   generic_sse:  7070.000 MB/sec
> <4>raid5: using function: generic_sse (7070.000 MB/sec)
> <4>raid6: int64x1   1592 MB/s
> <4>raid6: int64x2   2180 MB/s
> <4>raid6: int64x4   1751 MB/s
> <4>raid6: int64x8   1979 MB/s
> <4>raid6: sse2x1    2566 MB/s
> <4>raid6: sse2x2    3583 MB/s
> <4>raid6: sse2x4    3932 MB/s
> <4>raid6: using algorithm sse2x4 (3932 MB/s)
> <6>md: raid6 personality registered for level 6
> <6>md: raid5 personality registered for level 5
> <6>md: raid4 personality registered for level 4
> <4>GFS2 (built Sep  6 2006 16:09:57) installed
> <6>Lock_Nolock (built Sep  6 2006 16:10:14) installed
> <6>JFS: nTxBlock = 8192, nTxLock = 65536
> <6>SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
> <6>SGI XFS Quota Management subsystem
> <6>device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel at redhat.com
> <6>device-mapper: multipath: version 1.0.4 loaded
> <6>device-mapper: multipath round-robin: version 1.0.0 loaded
> <6>device-mapper: multipath emc: version 0.0.3 loaded
> <5>audit(1158518905.881:3): audit_pid=788 old=0 by auid=4294967295 subj=system_u:system_r:anaconda_t:s0
> <5>ReiserFS: sda7: found reiserfs format "3.6" with standard journal
> <5>ReiserFS: sda7: using ordered data mode
> <5>ReiserFS: sda7: journal params: device sda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
> <5>ReiserFS: sda7: checking transaction log (sda7)
> <5>ReiserFS: sda7: Using r5 hash to sort names
> <6>SELinux: initialized (dev sda7, type reiserfs), uses genfs_contexts

I'm curious: What was installed on this drive before you began the FC6T3 
installation?