Help needed with SanDisk CRUZER memory stick
Le Hong Boi
Le.Hong.Boi at sg.netnam.vn
Wed Dec 24 02:48:25 UTC 2003
The key problem here is
Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed
I also saw the similar problem with my USB CompactFlash reader. My FC1
can only recognize the CF Reader the 1st time it is connected; after
mounting the drive, unmounting it, disconnecting, reconnecting it, FC1
cannot recognize it with the same message as above.
Vào ngày Th 4 , 24/12/2003 lúc 02:41, 1072208461 viết rằng:
> I just got a SanDisk CRUZER 256MB USB memory thingy. It no workey!
>
> The USB is on a VIA 8235 chip if that matters.
>
> Could some of you gurus take a look at these messages and give me a
> clue about what I need to do to get this device working. I suspect
> that I'm missing a module, but I can't figure out what I need.
>
> Sorry about the size of this messages. I've trimmed out all the stuff
> that seemed irrelevant, but I didn't want to lose something
> important.
>
>
> Thanks,
>
> John
>
>
>
> Dec 22 20:11:21 localhost kernel: usb.c: registered new driver
> usbdevfs
> Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hub
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: $Revision: 1.275 $ time
> 16:47:59
> Dec 21 2003
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: High bandwidth mode
> enabled
> Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 11 for device 00:10.0
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xd400,
> IRQ 11
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports
> Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
> assigned bus
> number 1
> Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
> Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected
> Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 3 for device 00:10.1
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xd800,
> IRQ 3
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports
> Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
> assigned bus
> number 2
> Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
> Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected
> Dec 22 20:11:21 localhost kernel: PCI: Found IRQ 5 for device 00:10.2
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: USB UHCI at I/O 0xdc00,
> IRQ 5
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: Detected 2 ports
> Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
> assigned bus
> number 3
> Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
> Dec 22 20:11:21 localhost kernel: hub.c: 2 ports detected
> Dec 22 20:11:21 localhost kernel: usb-uhci.c: v1.275:USB Universal
> Host
> Controller Interface driver
> Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: PCI device
> 1106:3104
> Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: irq 10, pci mem
> e1bba000
> Dec 22 20:11:21 localhost kernel: usb.c: new USB bus registered,
> assigned bus
> number 4
> Dec 22 20:11:21 localhost kernel: ehci_hcd 00:10.3: USB 2.0 enabled,
> EHCI
> 1.00, driver 2003-Jun-19/2.4
> Dec 22 20:11:21 localhost kernel: hub.c: USB hub found
> Dec 22 20:11:21 localhost kernel: hub.c: 6 ports detected
> Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hiddev
> Dec 22 20:11:21 localhost kernel: usb.c: registered new driver hid
> Dec 22 20:11:21 localhost kernel: hid-core.c: v1.8.1 Andreas Gal,
> Vojtech
> Pavlik <vojtech at suse.cz>
> Dec 22 20:11:21 localhost kernel: hid-core.c: USB HID support drivers
> Dec 22 20:11:21 localhost kernel: hub.c: connect-debounce failed, port
> 2
> disabled
> Dec 22 20:11:21 localhost kernel: hub.c: new USB device 00:10.3-2,
> assigned
> address 2
> Dec 22 20:11:21 localhost kernel: usb.c: USB device 2 (vend/prod
> 0x781/0x8185)
> is not claimed by any active driver.
> Dec 22 20:11:21 localhost kernel: hub.c: new USB device 00:10.2-1,
> assigned
> address 2
> Dec 22 20:11:21 localhost kernel: usb.c: USB device 2 (vend/prod
> 0xaec/0x3050)
> is not claimed by any active driver.
> Dec 22 20:11:21 localhost kernel: Initializing USB Mass Storage
> driver...
> Dec 22 20:11:21 localhost kernel: usb.c: registered new driver
> usb-storage
> Dec 22 20:11:21 localhost kernel: scsi1 : SCSI emulation for USB Mass
> Storage
> devices
> Dec 22 20:11:21 localhost kernel: Vendor: Generic Model: STORAGE
> DEVICE
> Rev: 1.25
> Dec 22 20:11:21 localhost kernel: Type: Direct-Access
> ANSI SCSI revision: 02
> Dec 22 20:11:21 localhost kernel: scsi2 : SCSI emulation for USB Mass
> Storage
> devices
> Dec 22 20:11:21 localhost kernel: Vendor: SOYO Model: USB
> Storage-CFC
> Rev: 0208
> Dec 22 20:11:21 localhost kernel: Type: Direct-Access
> ANSI SCSI revision: 02
> Dec 22 20:11:21 localhost kernel: USB Mass Storage support registered.
> Dec 22 20:11:21 localhost kernel: Attached scsi removable disk sda at
> scsi1,
> channel 0, id 0, lun 0
> Dec 22 20:11:21 localhost kernel: Attached scsi removable disk sdb at
> scsi2,
> channel 0, id 0, lun 0
> Dec 22 20:11:21 localhost kernel: SCSI device sda: 512000 512-byte
> hdwr
> sectors (262 MB)
> Dec 22 20:11:21 localhost kernel: sda: Write Protect is off
> Dec 22 20:11:21 localhost kernel: sda: sda1
> Dec 22 20:11:21 localhost kernel: sdb: Unit Not Ready, sense:
> Dec 22 20:11:21 localhost kernel: Current 00:00: sns = 70 2
> Dec 22 20:11:21 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed.
> Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host
> = 0,
> driver = 08
> Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2
> Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512
> bytes,
> disk size 1GB.
> Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0
> Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0
> Dec 22 20:11:22 localhost kernel: unable to read partition table
> Dec 22 20:11:22 localhost kernel: sdb: Unit Not Ready, sense:
> Dec 22 20:11:22 localhost kernel: Current 00:00: sns = 70 2
> Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed.
> Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host
> = 0,
> driver = 08
> Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2
> Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512
> bytes,
> disk size 1GB.
> Dec 22 20:11:22 localhost kernel: sdb: Write Protect is off
> Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0
> Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0
> Dec 22 20:11:22 localhost kernel: unable to read partition table
> Dec 22 20:11:22 localhost kernel: Device not ready. Make sure there
> is a disc
> in the drive.
> Dec 22 20:11:22 localhost kernel: sdb: Unit Not Ready, sense:
> Dec 22 20:11:22 localhost kernel: Current 00:00: sns = 70 2
> Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:11:22 localhost kernel: sdb : READ CAPACITY failed.
> Dec 22 20:11:22 localhost kernel: sdb : status = 1, message = 00, host
> = 0,
> driver = 08
> Dec 22 20:11:22 localhost kernel: Current sd00:00: sns = 70 2
> Dec 22 20:11:22 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:11:22 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:11:22 localhost kernel: sdb : block size assumed to be 512
> bytes,
> disk size 1GB.
> Dec 22 20:11:22 localhost kernel: sdb: Write Protect is off
> Dec 22 20:11:22 localhost kernel: sdb: I/O error: dev 08:10, sector 0
> Dec 22 20:11:22 localhost kernel: I/O error: dev 08:10, sector 0
> Dec 22 20:11:22 localhost kernel: unable to read partition table
> Dec 22 20:11:22 localhost kernel: Device not ready. Make sure there
> is a disc
> in the drive.
> Dec 22 20:11:22 localhost kernel: usb.c: registered new driver usblp
> Dec 22 20:11:22 localhost kernel: printer.c: v0.11: USB Printer Device
> Class
> driver
> Dec 22 20:12:24 localhost kernel: hub.c: USB device not accepting new
> address
> (error=-71)
> Dec 22 20:12:24 localhost kernel: usb.c: USB disconnect on device
> 00:10.3-2
> address 2
> Dec 22 20:12:24 localhost kernel: hub.c: new USB device 00:10.3-2,
> assigned
> address 3
> Dec 22 20:12:27 localhost usb.agent[3564]: missing kernel or user mode
> driver
> usb-storage
> Dec 22 20:12:29 localhost kernel: usb-storage: host_reset() requested
> but not
> implemented
> Dec 22 20:12:39 localhost kernel: scsi: device set offline - command
> error
> recover failed: host 1 channel 0 id 0 lun 0
> Dec 22 20:12:39 localhost kernel: sdb: Unit Not Ready, sense:
> Dec 22 20:12:39 localhost kernel: Current 00:00: sns = 70 2
> Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:12:39 localhost kernel: sdb : READ CAPACITY failed.
> Dec 22 20:12:39 localhost kernel: sdb : status = 1, message = 00, host
> = 0,
> driver = 08
> Dec 22 20:12:39 localhost kernel: Current sd00:00: sns = 70 2
> Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:12:39 localhost kernel: sdb : block size assumed to be 512
> bytes,
> disk size 1GB.
> Dec 22 20:12:39 localhost kernel: sdb: Write Protect is off
> Dec 22 20:12:39 localhost kernel: sdb: I/O error: dev 08:10, sector 0
> Dec 22 20:12:39 localhost kernel: I/O error: dev 08:10, sector 0
> Dec 22 20:12:39 localhost kernel: unable to read partition table
> Dec 22 20:12:39 localhost kernel: Device not ready. Make sure there
> is a disc
> in the drive.
> Dec 22 20:12:39 localhost kernel: sdb: Unit Not Ready, sense:
> Dec 22 20:12:39 localhost kernel: Current 00:00: sns = 70 2
> Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:12:39 localhost kernel: sdb : READ CAPACITY failed.
> Dec 22 20:12:39 localhost kernel: sdb : status = 1, message = 00, host
> = 0,
> driver = 08
> Dec 22 20:12:39 localhost kernel: Current sd00:00: sns = 70 2
> Dec 22 20:12:39 localhost kernel: ASC=3a ASCQ= 0
> Dec 22 20:12:39 localhost kernel: Raw sense data:0x70 0x00 0x02 0x00
> 0x00 0x00
> 0x00 0x0a 0x00 0x00 0x00 0x00 0x3a 0x00 0x00 0x00 0x00 0x00
> Dec 22 20:12:39 localhost kernel: sdb : block size assumed to be 512
> bytes,
> disk size 1GB.
> Dec 22 20:12:39 localhost kernel: sdb: Write Protect is off
> Dec 22 20:12:39 localhost kernel: sdb: I/O error: dev 08:10, sector 0
> Dec 22 20:12:39 localhost kernel: I/O error: dev 08:10, sector 0
> Dec 22 20:12:39 localhost kernel: unable to read partition table
>
>
> --
> fedora-list mailing list
> fedora-list at redhat.com
> To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
Lê Hồng Bội
le.hong.boi at sg.netnam.vn
Phone: +84 91 3715235
http://lhboi.tripod.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.fedoraproject.org/pipermail/users/attachments/20031224/9044ae5b/attachment-0002.html
More information about the users
mailing list