IT8212

[Alexandre Cavalcante Alencar]

Hi,

I've a GA-7N400 Pro and a GA-7N400 Pro 2 that have this same controller,
but I can't compile the driver modules. I receive lots of erros, missing
headers, missing declarations, etc...

I've get the v.145 driver...

How do you make it compile?

ATS,


-- 
Alexandre Cavalcante Alencar (Skarmeth)
alexandre at debian-ce.org skarmeth at debian-ce.org
http://people.debian-ce.org/skarmeth/

Grupo de Usuários GNU/Linux e de Software Livre do Ceará - Debian-CE
http://www.debian-ce.org
http://listas.cipsga.org.br/cgi-bin/mailman/listinfo/debian-ce
       
Projeto Software Livre Ceará - PSL-CE
http://psl-ce.softwarelivre.org
http://listas.softwarelivre.org/mailman/listinfo/psl-ce

Linux Registred User....: 260571    ICQ Instant Message.....: 87355854
Yahoo Instant Message...: Skarmeth  Skype IP Telephony......: Skarmeth

On Sat, 2004-11-13 at 07:02, Mile Davidovic wrote:
> Hi Folks
> 
> Is anyone succedd to use ITE8212 Raid controler (on Gigabyte boards called
> GigaRaid) on FC3? 
> I have some problem with building modules but dmesg shows:
> 	Found Controller: IT8212 UDMA/ATA133 RAID Controller
> 	FindDevices: device 0 is IDE
> 	FindDevices: device 1 is IDE
> 	Channel[0] BM-DMA at 0xA400-0xA407
> 	Channel[1] BM-DMA at 0xA408-0xA40F
> 	scsi2 : ITE RAIDExpress133
> 	  Vendor: ITE       Model: IT8212F           Rev: 1.3
> 	  Type:   Direct-Access                      ANSI SCSI revision: 00
> 	SCSI device sdb: 488397166 512-byte hdwr sectors (250059 MB)
> 	sdb: asking for cache data failed
> 	sdb: assuming drive cache: write through
> 	 sdb: sdb1
> 	Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
> 	  Vendor: ITE       Model: IT8212F           Rev: 1.3
> 	  Type:   Direct-Access                      ANSI SCSI revision: 00
> 	SCSI device sdc: 488397166 512-byte hdwr sectors (250059 MB)
> 	sdc: asking for cache data failed
> 	sdc: assuming drive cache: write through
> 	 sdc:<4>atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
> isa0060/serio0).
> 	atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
> 	atkbd.c: Unknown key pressed (translated set 2, code 0x0 on
> isa0060/serio0).
> 	atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
> 	 sdc1
> 	Attached scsi disk sdc at scsi2, channel 0, id 1, lun 0
> 
> [root at beowulf scsi]# mount /dev/sdb1 /mnt/
> atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
> atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
> ...
> atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
> atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
> kjournald starting.  Commit interval 5 seconds
> atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
> atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
> EXT3 FS on sdb1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> atkbd.c: Unknown key pressed (translated set 2, code 0x0 on isa0060/serio0).
> atkbd.c: Use 'setkeycodes 00 <keycode>' to make it known.
> 
> Best regards
> Mile Davidovic, B.Sc.
> --
> Mile.Davidovic at micronasnit.com
> MicronasNIT LLC.
> http://www.micronasnit.com
> Fruskogorska 11a, 21000 Novi Sad, Serbia & Montenegro
> Phone (1) : +381 (0)21 475 00 24 (ext. 111)
> Phone (2) : +381 (0)21 475 00 28 (ext. 112)
> Fax           : +381 (0)21 450 721
>