(no subject)

[John L. Pierce]

Pete, forgive the delay I work the majority of my shifts over the
weekend.

I tried the boot with the modprobe.conf file below and still no
driver loaded at boot.

<<
alias eth0 via-rhine
alias snd-card-1 snd-au8810
#install snd-au8810 /sbin/modprobe --ignore-install snd-au8810
&& /usr/sbin/alsactl restore >/dev/null 2>&1 || :
remove snd-au8810 { /usr/sbin/alsactl store >/dev/null 2>&1
|| : ; }; /sbin/modprobe -r --ignore-remove snd-au8810
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
# bttv
alias char-major-81 bttv
options bttv card=10 radio=0 tuner=39
>>

I have gone as far as removing the card and allowing the system to
reboot, kudzu checks for new hardware and informs me that the following
device has been removed from my system

Brooktree Corporation bt878 video capture card

I have then re-installed the card and kudzu tells me that the following 
device has been added to my system.

First Screen

Brooktree Corporation bt878 video capture device
        audio capture device

Second Screen

Brooktree Corporation bt878 video capture device
        video capture device

On both screens I elect to configure the device.

I am running a stock fedora kernel, output of uname -a

<<
Linux ns2.local.net 2.6.10-1.770_FC3 #1 Thu Feb 24 14:00:06 EST 2005
i686 athlon i386 GNU/Linux
>>

If I modprobe bttv this is the tail of dmesg:

Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:00:09.0, irq: 3, latency: 32, mmio:
0xd8141000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is
0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
bttv0: Hauppauge eeprom: model=29440, tuner=LG TPI8PSB01D (28), radio=no
bttv0: using tuner=39
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips:
tda9840,tda9873h,tda9874h/a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951),ta8874z
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 39 (LG NTSC (newer TAPC series)) by bt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: SCERR @ 0ecf0014,bits: HSYNC FBUS SCERR*
bttv0: PLL can sleep, using XTAL (28636363).

I am just about to go by a WinTV PVR150 MCE and switch to the ivtv
driver.

I am at a complete loss.

John
--