FC5 : Failed to allocate memory resource

[alan]

On Wed, 5 Apr 2006, Dan wrote:

> Gavin Li wrote:
>> 
>> I just installed FC5 on my brandnew PC, It prompts the following message 
>> when booting up:
>>
>> 
>> Uncompressing liux kernel  OK
>> 
>> PCI: Failed to allocate memory resource #6 : 20000:50000000 for 0:01:00.0
>>
>> 
>> I did a lspci after bootup:
>> 
>> # uname -r
>> 
>> 2.6.15-1.2054_FC5smp
>> 
>> # lspci
>> 
>> 00:00.0 Host bridge: Intel Corporation 945G/P Memory Controller Hub
>> 
>> 00:01.0 PCI bridge: Intel Corporation 945G/P PCI Express Graphics Port
>> 
>> 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High 
>> Definition Audio Controller (rev 01)
>> 
>> 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
>> 1 (rev 01)
>> 
>> 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
>> 3 (rev 01)
>> 
>> 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 
>> 4 (rev 01)
>> 
>> 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 
>> (rev 01)
>> 
>> 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 
>> (rev 01)
>> 
>> 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 
>> (rev 01)
>> 
>> 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 
>> (rev 01)
>> 
>> 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI 
>> Controller (rev 01)
>> 
>> 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
>> 
>> 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC 
>> Interface Bridge (rev 01)
>> 
>> 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE 
>> Controller (rev 01)
>> 
>> 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial 
>> ATA Storage Controllers cc=IDE (rev 01)
>> 
>> 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 
>> 01)
>> 
>> 01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600] 
>> (rev a2)
>> 
>> 05:02.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 
>> Controller (PHY/Link)
>> 
>> 05:08.0 Ethernet controller: Intel Corporation 82801G (ICH7 Family) LAN 
>> Controller (rev 01)
>> 
>> #
>>
>> 
>> Is this mean the "01:00.0 VGA compatible controller: nVidia Corporation 
>> NV43 [GeForce 6600] (rev a2)" is bad?
>>
>>
>> 
>> Gavin
>> 
> Does it boot? If it does, I wouldn't worry too much about it; I get this for 
> both the old and new video card in my desktop, and Doom 3 and Quake 4 still 
> run excellently.

I also see this on my HP zv5200 AMD64 laptop, but it is refering to the 
cardbus slot.

PCI: Failed to allocate mem resource #10:2000000 at e2000000 for 0000:01:04.0
PCI: Failed to allocate mem resource #10:2000000 at e2000000 for 0000:01:04.1
PCI: Bus 2, cardbus bridge: 0000:01:04.0
   IO window: 00003000-000030ff
   IO window: 00003400-000034ff
   PREFETCH window: 50000000-51ffffff
PCI: Bus 6, cardbus bridge: 0000:01:04.1
   IO window: 00003800-000038ff
   IO window: 00003c00-00003cff
   PREFETCH window: 52000000-53ffffff
PCI: Bridge: 0000:00:0a.0
   IO window: 3000-7fff
   MEM window: e0100000-e17fffff
   PREFETCH window: 50000000-53ffffff
PCI: Bridge: 0000:00:0b.0
   IO window: disabled.
   MEM window: e2000000-e2ffffff
   PREFETCH window: f0000000-f80fffff


01:04.0 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 
01)
01:04.1 CardBus bridge: Texas Instruments PCI1620 PC Card Controller (rev 
01)


-- 
"Remember there is a big difference between kneeling down and bending over." - Frank Zappa