2.6.22-41 and bcm43xx
Jesus Jr M Salvo
jesus.m.salvo at gmail.com
Sun Aug 12 02:44:01 UTC 2007
With the new kernel ( 2.6.22.1-41 x86_64 ), I started getting these
error messages during bootup ( which I did not receive in previous
kernels such as 2.6.21-1.3228:
bcm43xx-phy0 debug: Adding Interface type 2
ssb: Switching to PCI-E core, index 3
ssb: Switching to IEEE 802.11 core, index 1
bcm43xx-phy0 debug: Loading firmware version 371.1061 (2006-10-04 21:02:04)
ssb: Switching to ChipCommon core, index 0
ssb: Switching to IEEE 802.11 core, index 1
bcm43xx-phy0 debug: Radio turned on
bcm43xx-phy0 debug: Radio enabled by hardware
bcm43xx-phy0 debug: bbatt(11) >= size of LO array
Call Trace:
[<ffffffff881f2abf>] :bcm43xx_mac80211:bcm43xx_get_lo_g_ctl+0x65/0xa8
[<ffffffff881f2b38>] :bcm43xx_mac80211:bcm43xx_lo_g_ctl_current+0x36/0x3b
[<ffffffff881f2c1c>] :bcm43xx_mac80211:bcm43xx_lo_g_adjust+0x9/0x15
[<ffffffff881ed25f>] :bcm43xx_mac80211:bcm43xx_phy_init_pctl+0x338/0x6a6
[<ffffffff881e7af4>] :bcm43xx_mac80211:bcm43xx_phy_read+0x5c/0x63
[<ffffffff881f052c>] :bcm43xx_mac80211:bcm43xx_phy_initg+0xc85/0xd0a
[<ffffffff881f0d5f>] :bcm43xx_mac80211:bcm43xx_phy_init+0x582/0x5a7
[<ffffffff881e4cce>] :bcm43xx_mac80211:bcm43xx_chip_init+0x68c/0x9a3
[<ffffffff881e526d>] :bcm43xx_mac80211:bcm43xx_wireless_core_init+0x288/0x73e
[<ffffffff881e62bb>] :bcm43xx_mac80211:bcm43xx_add_interface+0x5f/0xf4
[<ffffffff881b16e4>] :mac80211:ieee80211_open+0x21d/0x34d
[<ffffffff8124354d>] wext_handle_ioctl+0x354/0x39d
[<ffffffff811df4af>] dev_open+0x2f/0x6e
[<ffffffff811dd677>] dev_change_flags+0x5a/0x118
[<ffffffff8122180f>] devinet_ioctl+0x235/0x597
[<ffffffff8124adde>] do_page_fault+0x476/0x7b4
[<ffffffff811d3053>] sock_ioctl+0x1c8/0x1e5
[<ffffffff8109e807>] do_ioctl+0x2b/0xb6
[<ffffffff8109ead5>] vfs_ioctl+0x243/0x25c
[<ffffffff8109eb47>] sys_ioctl+0x59/0x7a
[<ffffffff81009cd5>] tracesys+0xd5/0xda
bcm43xx-phy0 debug: Chip initialized
bcm43xx-phy0 debug: 32-bit DMA initialized
bcm43xx-phy0 debug: Wireless interface started
ADDRCONF(NETDEV_UP): wlan0: link is not ready
Any ideas ?
More information about the users
mailing list