NTP fails synchronization with server at startup

[Paul Smith]

On Dec 5, 2007 11:40 PM, Paul Smith <phhs80 at gmail.com> wrote:
> > > > > > Another thing. Are you sure that ntp isn't doing it's stuff, even
> > > > > > though the bootup shows a fail. Before you do the ntpd restart, run
> > > > > > the following as user.
> > > > > >
> > > > > > /usr/sbin/ntpq
> > > > > > then type pe, which will give you some info on which servers ntp is
> > > > > > trying to connect to, and how successfull it is being. You can keep
> > > > > > typing pe at intervals, which will show ntp's progress at reaching a
> > > > > > point where a time server is being used as a "sys peer". The server
> > > > > > being used will be prefixed by a "*". Other useable servers will be
> > > > > > prefixed by a "+" "candidat". To quit ntpq type q.
> > > > >
> > > > > Thanks, Nigel. In fact,
> > > > > # /usr/sbin/ntpq
> > > > > ntpq> pe
> > > > > No association ID's returned
> > > > > ntpq> pe
> > > > >      remote           refid      st t when poll reach   delay   offset
> > > > > jitter
> > > > > =======================================================================
> > > > >==== === clock-a.develoo 192.12.19.20     2 u   28   64    3  190.143
> > > > > 438.261 9.311 ntpq>
> > > >
> > > > Well it appears to have a connection to the timeserver here, and often
> > > > takes a while before the timeserver is accepted as a system peer. Then an
> > > > "*" will appear before clock-a.develoo. Your reach is showing as 3, and
> > > > will gradually progress until it reaches 377, but this can take some
> > > > time.
> > > >
> > > > > i.e., when I run pe after a while, I get the above, but the first time
> > > > > I run pe, I get
> > > > >
> > > > > 'No association ID's returned'
> > > >
> > > > That usually indicates that ntp cannot contact the timeserver, no network
> > > > connection, or the timeserver is not accessable.
> > > >
> > > > > Can I be sure that ntp is running now and synchronizing with a ntp
> > > > > server?
> > > >
> > > > It appears to be running, but I think you have a problem in only having
> > > > one timeserver available.
> > > >
> > > > > Paul
> > > >
> > > > Paul. I'd still suggest that you add more timeservers to your
> > > > /etc/ntp.conf. Try the 3 that I am using. I know they are not the closest
> > > > to you, but they have been reliable for me. As I mentioned earlier, make
> > > > sure that everything in /etc/ntp.conf is commented out, except the
> > > > driftfile line, comment out also your present server, and add the ones
> > > > I've listed below. Save the changes, restart the ntp daemon, and rerun
> > > > /usr/sbin/ntpq. Type pe every minute or so, and see how it progresses.
> > > >
> > > > server ntp.obspm.fr
> > > > server ntp.kamino.fr
> > > > server ntp2.belbone.be
> > > >
> > > > Is this just the one machine you have connected to the Internet, or are
> > > > you on a LAN with other machines that are also using ntp to get their
> > > > time from Internet timeservers?
> > >
> > > Thanks again, Nigel. Does it seem that it is working now?
> > >
> > > # /usr/sbin/ntpq
> > > ntpq> pe
> > >      remote           refid      st t when poll reach   delay   offset
> > > jitter
> > > ===========================================================================
> > >=== *syrte8.obspm.fr 134.157.254.19   2 u   27   64  377   62.413  132.612
> > > 16.037 +ns1.kamino.fr   193.52.184.106   2 u   20   64  377   85.748
> > > 119.231  10.125 +ntp2.belbone.be 195.13.23.6      2 u   54   64  377
> > > 69.566  104.344  12.046 ntpq>
> > >
> > > No, I am directly connected to the Internet, with no LAN in between.
> > >
> > > Paul
> >
> > That looks fine, and just what I'd expect to see.
>
> I have just noticed that at booting, the Network Manager daemon is
> loaded after the ntp one. This may be the cause of the problem.

How can I configure my computer in order to have ntp being launched
after the network manager daemon?

Paul