FC7 Atheros wireless card
antonio montagnani
antonio.montagnani at gmail.com
Thu Jun 14 12:44:52 UTC 2007
2007/6/14, Manuel Arostegui Ramirez <manuel at todo-linux.com>:
> On Thursday 14 June 2007 13:48:28 antonio montagnani wrote:
> > I am running a D-Link G-650 that was o.k on FC6.
> > I made afresh installation, I installed madwifi from freshrpms, then I
> > rebooted. Now if I open the Network administration page I do not see the
> > wifi-card (no ath0, no wifi0), but
> > the output of lspi is:
> >
> > 03:00.0 Ethernet controller: Atheros Communications, Inc. AR5212
> > 802.11abg NIC (rev 01)
> >
> > the output of lsmod is:
> > Module Size Used by
> > wlan_tkip 15872 0
> > wlan_ccmp 11776 0
> > wlan_scan_sta 16512 1
> > ath_pci 92832 0
> > ath_rate_sample 15744 1
> > wlan 186052 6
> > wlan_tkip,wlan_ccmp,wlan_scan_sta,ath_rate_sample,ath_pci
> > ath_hal 195408 3 ath_rate_sample,ath_pci
> >
> > so all necessary modules are loaded...
> >
> > If I issue an ipconfig I get:
> >
> > ifconfig
> > ath0 Link encap:Ethernet HWaddr 00:15:E9:2F:EE:A7
> > UP BROADCAST MULTICAST MTU:1500 Metric:1
> > RX packets:14 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:76 errors:1 dropped:1 overruns:0 carrier:0
> > collisions:0 txqueuelen:0
> > RX bytes:2145 (2.0 KiB) TX bytes:15878 (15.5 KiB)
> >
> > eth0 Link encap:Ethernet HWaddr 00:03:0D:04:A3:10
> > inet addr:192.168.0.20 Bcast:192.168.0.255 Mask:255.255.255.0
> > inet6 addr: fe80::203:dff:fe04:a310/64 Scope:Link
> > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > RX packets:1571 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:1549 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:1000
> > RX bytes:1155014 (1.1 MiB) TX bytes:430040 (419.9 KiB)
> > Interrupt:16 Base address:0x2000
> >
> > lo Link encap:Local Loopback
> > inet addr:127.0.0.1 Mask:255.0.0.0
> > inet6 addr: ::1/128 Scope:Host
> > UP LOOPBACK RUNNING MTU:16436 Metric:1
> > RX packets:14 errors:0 dropped:0 overruns:0 frame:0
> > TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
> > collisions:0 txqueuelen:0
> > RX bytes:1036 (1.0 KiB) TX bytes:1036 (1.0 KiB)
> >
> > wifi0 Link encap:UNSPEC HWaddr
> > 00-15-E9-2F-EE-A7-78-19-00-00-00-00-00-00-00-00
> > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> > RX packets:20649 errors:0 dropped:0 overruns:0 frame:11548
> > TX packets:687 errors:0 dropped:1 overruns:0 carrier:0
> > collisions:0 txqueuelen:199
> > RX bytes:2750101 (2.6 MiB) TX bytes:52867 (51.6 KiB)
> > Interrupt:16
> >
> >
> > How can I have an wifi0 or ath0 that I do not see in the Network
> > configuration window????
> >
> > Tnx for help
> >
>
> What happen if you try to configure your wireless network using iwconfig, I
> mean, from the CLI?
> Does it work?
>
>
> --
> Manuel Arostegui Ramirez.
>
> Electronic Mail is not secure, may not be read every day, and should not
> be used for urgent or sensitive issues.
>
> --
> fedora-list mailing list
> fedora-list at redhat.com
> To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
>
what do you mean??? In any case I made another trial to create a
ifgc-atho file but id didn't work... The real question is why I see an
ath0 in ifconfig but I do not see it in my Network configuration
window :-(
--
Antonio Montagnani
Skype : antoniomontag
More information about the users
mailing list