Printer problem Samsung CLX-3170

[Jim]

On 11/23/2011 02:47 PM, mike cloaked wrote:
> On Wed, Nov 23, 2011 at 5:23 PM, Jim<binarynut at comcast.net>  wrote:
>> On 11/23/2011 09:34 AM, mike cloaked wrote:
>>> On Tue, Nov 22, 2011 at 12:17 PM, Jim<binarynut at comcast.net>    wrote:
>>>
>>>>> I can't tell from the messages output you posted if your machine is
>>>>> x86_64 or not but I had a very very similar issue with a Samsung
>>>>> scx4500w when I installed f16.
>>>>>
>>>>> It turned out that the copy of the file "rastertosamsungspl" was a 32
>>>>> bit version and I had installed a 64 bit system - worth checking ?
>>>>>
>>>>> Also I notice that the name of your file is "rastertosamsungsplc"
>>>>> whereas it should be "rastertosamsungspl" i.e. you have an additional
>>>>> letter "c" at the end of the filename - if your file is really ending
>>>>> in a "c" then check whether you have the correct 32 or 64 bit file -
>>>>> if not then make sure that where you defined the file in the printer
>>>>> setup is correct - if not then redefine it with the correct filename.
>>>> I have a 32 bit box,
>>>> How do I determine wether the rastertosamungsplc is 32 or  64 bit?
>>>> In usr/lib/cups/filter/ there is a rastertosamsungsplc and a
>>>> rastertosamsungspl .
>>>> This is the same driver that I used Fedora 14 and 15 .
>>> OK - the answer as to which of 32 or 64 bit is where you got the file
>>> from?  Presumably it is from the unified driver set from Samsung - in
>>> which case that will have difference directories for the 32bit and 64
>>> bit file sets - one thing you can do is go back there and check the
>>> total file size - the 32 and 64 bit raster files are different sizes -
>>> which does yours match?
>>>
>>> Secondly you did not answer the question about using the correct name
>>> for the file when you defined the printer in Fedora - unless you
>>> changed the name of the actual file then the fail message indicated
>>> that you had the wrong filename - if course if you define it and point
>>> to a non-existent file then it is bound to fail!  Check that again and
>>> see if that is the source of the problem.
>>>
>>>
>> THe unifiedLinuxDriver is the one I,m using ,it is the SAME driver that
>> I have installed on  32 bit boxes in Fedora 14 an 15 for this CLX3175FN
>> printer and now a 32 bit box in Fedora 16.
>>
>> The only thing I put into the setup was:
>>
>> URL: lpd://192.168.000.005         (this is the IP in the Router for
>> this printer, the same IP used on F14, F15)
>>
>> The rest was done in the setup.
>>
>> THanks Mike for your help on this problem.
> Can you try to print again - and send the error exactly as it appears please -
>
>
ov 23 17:05:35 BigOne dbus[915]: [system] Activating service 
name='org.opensuse.CupsPkHelper.Mechanism' (using servicehelper)
Nov 23 17:05:35 BigOne dbus-daemon[915]: dbus[915]: [system] Activating 
service name='org.opensuse.CupsPkHelper.Mechanism' (using servicehelper)
Nov 23 17:05:35 BigOne dbus[915]: [system] Successfully activated 
service 'org.opensuse.CupsPkHelper.Mechanism'
Nov 23 17:05:35 BigOne dbus-daemon[915]: dbus[915]: [system] 
Successfully activated service 'org.opensuse.CupsPkHelper.Mechanism'
Nov 23 17:05:36 BigOne kernel: [  241.033635] rastertosamsung[1707] 
general protection ip:4e8ab700 sp:bfe0d7e4 error:0 in 
libc-2.14.90.so[4e771000+1a5000]
Nov 23 17:05:36 BigOne abrtd: Directory 'ccpp-2011-11-23-17:05:36-1707' 
creation detected
Nov 23 17:05:36 BigOne abrt[1716]: Saved core dump of pid 1707 
(/usr/lib/cups/filter/rastertosamsungsplc) to 
/var/spool/abrt/ccpp-2011-11-23-17:05:36-1707 (1323008 bytes)
Nov 23 17:05:37 BigOne abrtd: Executable 
'/usr/lib/cups/filter/rastertosamsungsplc' doesn't belong to any package
Nov 23 17:05:37 BigOne abrtd: Corrupted or bad dump 
/var/spool/abrt/ccpp-2011-11-23-17:05:36-1707 (res:2), deleting