[fedora-arm] Cubietruck failure with Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)

Fri Oct 23 20:34:44 UTC 2015

Sunday/monday I will try another card.  I have used this card many times 
in the past, using your script to lay down the image on the card.

On 10/23/2015 01:54 PM, Paul Whalen wrote:
>
> ----- Original Message -----
>> It has been a while since I tried any Fedora-23 builds what with a
>> number of things going on.  So seeing the go/nogo, I figured I better
>> run a test and as you can see it failed (and I tried booting twice with
>> this image and got the same results):
> The image is working Ok here(tested on the Banana Pi Pro), I've found the
> Cubietruck to be a little picky with mSD's and Ive seen the same error
> when using anything but Silicon Power branded cards. YMMV..
>
> Thanks for testing Robert!
>
> Paul
>
>
>>
>> U-Boot SPL 2015.07 (Sep 12 2015 - 10:46:32)
>> DRAM: 2048 MiB
>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
>>
>>
>> U-Boot 2015.07 (Sep 12 2015 - 10:46:32 +0000) Allwinner Technology
>>
>> CPU:   Allwinner A20 (SUN7I)
>> I2C:   ready
>> DRAM:  2 GiB
>> MMC:   SUNXI SD/MMC: 0
>> *** Warning - bad CRC, using default environment
>>
>> Setting up a 1024x768 vga console
>> In:    serial
>> Out:   vga
>> Err:   vga
>> SCSI:  SUNXI SCSI INIT
>> SATA link 0 timeout.
>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
>> flags: ncq stag pm led clo only pmp pio slum part ccc apst
>> Net:   eth0: ethernet at 01c50000
>> starting USB...
>> USB0:   USB EHCI 1.00
>> USB1:   USB OHCI 1.0
>> USB2:   USB EHCI 1.00
>> USB3:   USB OHCI 1.0
>> scanning bus 0 for devices... 1 USB Device(s) found
>> scanning bus 2 for devices... 1 USB Device(s) found
>> scanning bus 1 for devices... unable to get device descriptor (error=-1)
>> 1 USB Device(s) found
>> scanning bus 3 for devices... 1 USB Device(s) found
>> Hit any key to stop autoboot:  0
>> switch to partitions #0, OK
>> mmc0 is current device
>> Scanning mmc 0:1...
>> Found /extlinux/extlinux.conf
>> Retrieving file: /extlinux/extlinux.conf
>> 494 bytes read in 127 ms (2.9 KiB/s)
>> Ignoring unknown command: ui
>> Ignoring malformed menu command:  autoboot
>> Ignoring malformed menu command:  hidden
>> Ignoring unknown command: totaltimeout
>> Fedora-Xfce-armhfp-23-3 Boot Options.
>> 1:    Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
>> Enter choice: 1:    Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl)
>> Retrieving file: /initramfs-4.2.3-300.fc23.armv7hl.img
>>    ** ext4fs_devread read error - block
>> Skipping Fedora-Xfce-armhfp-23-3 (4.2.3-300.fc23.armv7hl) for failure
>> retrieving
>>    initrd
>> SCRIPT FAILED: continuing...
>> ** Can't read partition table on 0:0 **
>> ** Invalid partition 1 **
>> ** Can't read partition table on 0:0 **
>> ** Invalid partition 1 **
>> ** Can't read partition table on 0:0 **
>> ** Invalid partition 1 **
>> ** Can't read partition table on 0:0 **
>> ** Invalid partition 1 **
>> ** Can't read partition table on 0:0 **
>> ** Invalid partition 1 **
>> scanning bus for devices...
>> Found 0 device(s).
>>
>> SCSI device 0:
>>       Device 0: not available
>>
>> USB device 0: unknown device
>> ethernet at 01c50000 Waiting for PHY auto negotiation to complete.... done
>> Speed: 100, full duplex
>> BOOTP broadcast 1
>> BOOTP broadcast 2
>> BOOTP broadcast 3
>> BOOTP broadcast 4
>> BOOTP broadcast 5
>> BOOTP broadcast 6
>> DHCP client bound to address 192.168.160.23 (5805 ms)
>> *** Warning: no boot file name; using 'C0A8A017.img'
>> Using ethernet at 01c50000 device
>> TFTP from server 0.0.0.0; our IP address is 192.168.160.23; sending
>> through gate
>> way 192.168.160.1
>> Filename 'C0A8A017.img'.
>> Load address: 0x42000000
>> Loading: T T T T T T T T T T
>> Retry count exceeded; starting again
>> missing environment variable: pxeuuid
>> Retrieving file: /extlinux/pxelinux.cfg/01-02-c1-08-81-e2-d7
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C0A8A017
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C0A8A01
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C0A8A0
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C0A8A
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C0A8
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C0A
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C0
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/C
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/default-arm-sunxi
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/default-arm
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Retrieving file: /extlinux/pxelinux.cfg/default
>> Speed: 100, full duplex
>> *** ERROR: `serverip' not set
>> Config file not found
>> Speed: 100, full duplex
>> BOOTP broadcast 1
>> DHCP client bound to address 192.168.160.23 (11 ms)
>> Using ethernet at 01c50000 device
>> TFTP from server 0.0.0.0; our IP address is 192.168.160.23; sending
>> through gate
>> way 192.168.160.1
>> Filename 'boot.scr.uimg'.
>> Load address: 0x43100000
>> Loading: T T T T T T T T T T
>> Retry count exceeded; starting again
>> sunxi#
>>
>> _______________________________________________
>> arm mailing list
>> arm at lists.fedoraproject.org
>> https://admin.fedoraproject.org/mailman/listinfo/arm