Am 04.05.21 um 16:58 schrieb Peter Robinson:
U-Boot 2021.04 (Apr 28 2021 - 00:00:00)
U-Boot TPL 2021.04 (Apr 21 2021 - 00:00:00) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM...
U-Boot SPL 2021.04 (Apr 21 2021 - 00:00:00 +0000) Trying to boot from MMC2
U-Boot 2020.10-1 (Oct 14 2020 - 10:43:46 +0000) Manjaro ARM
Yep, so you probably need to disable the EMMC because it's loading it from the EMMC for some reason.
If it loads to Fedora you can also run "dd if=/dev/zero of=/dev/mmcblkX bs=1M count=10" (update the mmcblkX to the right one) to zero out the beginning of the EMMC if you don't care about the contents of it. _______________________________________________ arm mailing list -- arm@lists.fedoraproject.org To unsubscribe send an email to arm-leave@lists.fedoraproject.org Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@lists.fedoraproject.org Do not reply to spam on the list, report it: https://pagure.io/fedora-infrastructure
After "dd if=/dev/zero of=/dev/mmcblkX bs=1M count=10" I want to boot with Fedora-Everything-netinst-aarch64-34-1.2.iso
How to boot from USB?
Message
U-Boot TPL 2021.04 (Apr 21 2021 - 00:00:00) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM...
U-Boot SPL 2021.04 (Apr 21 2021 - 00:00:00 +0000) Trying to boot from MMC2 mmc_load_image_raw_sector: mmc block read error Trying to boot from SPI
U-Boot 2021.04 (Apr 21 2021 - 00:00:00 +0000)
SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 Pinebook Pro DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPIFlash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment
In: serial Out: vidconsole Err: vidconsole Model: Pine64 Pinebook Pro Net: No ethernet found. starting USB... Bus usb@fe380000: USB EHCI 1.00 Bus usb@fe3a0000: USB OHCI 1.0 Bus usb@fe3c0000: USB EHCI 1.00 Bus usb@fe3e0000: USB OHCI 1.0 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus dwc3: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fe380000 for devices... 1 USB Device(s) found scanning bus usb@fe3a0000 for devices... 2 USB Device(s) found scanning bus usb@fe3c0000 for devices... 4 USB Device(s) found scanning bus usb@fe3e0000 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning bus dwc3 for devices... 1 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0(part 0) is current device ** No partition table - mmc 0 ** Card did not respond to voltage select! : -110
Device 0: Vendor: 0x15b7 Rev: 211070WD Prod: 2018FV440610 Type: Hard Disk Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) ... is now current device ** No partition table - nvme 0 **
Device 0: Vendor: Verbatim Rev: PMAP Prod: STORE N GO Type: Removable Hard Disk Capacity: 14808.0 MB = 14.4 GB (30326784 x 512) ... is now current device Scanning usb 0:1... No ethernet found. missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-rk3399-pinebook-pro-rk3399 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-rk3399 No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm No ethernet found. missing environment variable: bootfile Retrieving file: pxelinux.cfg/default No ethernet found. Config file not found No ethernet found. No ethernet found. SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB dhcp - boot image via network using DHCP/TFTP protocol
Usage: dhcp [loadAddress] [[hostIPaddr:]bootfilename] ## Executing script at 00500000 Wrong image format for "source" command SCRIPT FAILED: continuing... =>