Hard Freezes with F20 on Lenovo ThinkPad T430

[Oliver Ruebenacker]

     Hello,

  I'm having multiple hard freezes a day with Fedora 20 on a Lenovo
ThinkPad T430. Display stops moving, even mouse cursor, with no previous
warning. I have the problem since Fedora 19.

  Any ideas?

  I'm copying a few lines from /var/log/messages showing lines from some
time before the crash until the restart (see below).

  Thanks!

     Best,
     Oliver

-- 
Oliver Ruebenacker
Founder at Relomics Consulting <http://www.relomics.com>
Be always grateful, but never satisfied.

Feb 27 13:19:01 localhost kernel: [    9.397141] thinkpad_acpi: ThinkPad
BIOS G1ET73WW (2.09 ), EC unknown
Feb 27 13:19:01 localhost kernel: [    9.397141] thinkpad_acpi: Lenovo
ThinkPad T430, model 2342CTO
Feb 27 13:19:01 localhost kernel: [    9.397474] thinkpad_acpi: Unsupported
brightness interface, please contact ibm-acpi-devel(a)lists.sourceforge.net
Feb 27 13:19:01 localhost kernel: [    9.397582] thinkpad_acpi: radio
switch found; radios are enabled
Feb 27 13:19:01 localhost kernel: [    9.397591] thinkpad_acpi: This
ThinkPad has standard ACPI backlight brightness control, supported by the
ACPI video driver
Feb 27 13:19:01 localhost kernel: [    9.397592] thinkpad_acpi: Disabling
thinkpad-acpi brightness events by default...
Feb 27 13:19:01 localhost kernel: [    9.398576] thinkpad_acpi: Console
audio control enabled, mode: monitor (read only)
Feb 27 13:19:01 localhost kernel: [    9.401050] input: ThinkPad Extra
Buttons as /devices/platform/thinkpad_acpi/input/input9
Feb 27 13:19:01 localhost kernel: [    9.406826] input: HDA Intel PCH Dock
Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
Feb 27 13:19:01 localhost kernel: [    9.406908] input: HDA Intel PCH
Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
Feb 27 13:19:01 localhost kernel: [    9.406956] input: HDA Intel PCH Dock
Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
Feb 27 13:19:01 localhost kernel: [    9.407002] input: HDA Intel PCH Mic
as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
Feb 27 13:19:01 localhost kernel: [    9.407830] i801_smbus 0000:00:1f.3:
SMBus using PCI Interrupt
Feb 27 13:19:01 localhost kernel: [    9.407917] ACPI Warning:
0x0000000000000428-0x000000000000042f SystemIO conflicts with Region
\_SB_.PCI0.LPC_.PMIO 1 (20131115/utaddress-251)
Feb 27 13:19:01 localhost kernel: [    9.407922] ACPI: If an ACPI driver is
available for this device, you should use it instead of the native driver
Feb 27 13:19:01 localhost kernel: [    9.407929] ACPI Warning:
0x0000000000000530-0x000000000000053f SystemIO conflicts with Region
\_SB_.PCI0.LPC_.LPIO 1 (20131115/utaddress-251)
Feb 27 13:19:01 localhost kernel: [    9.407932] ACPI: If an ACPI driver is
available for this device, you should use it instead of the native driver
Feb 27 13:19:01 localhost kernel: [    9.407933] ACPI Warning:
0x0000000000000500-0x000000000000052f SystemIO conflicts with Region
\_SB_.PCI0.LPC_.LPIO 1 (20131115/utaddress-251)
Feb 27 13:19:01 localhost kernel: [    9.407936] ACPI: If an ACPI driver is
available for this device, you should use it instead of the native driver
Feb 27 13:19:01 localhost kernel: [    9.407938] lpc_ich: Resource
conflict(s) found affecting gpio_ich
Feb 27 13:19:01 localhost kernel: [    9.426112] e1000e: Intel(R) PRO/1000
Network Driver - 2.3.2-k
Feb 27 13:19:01 localhost kernel: [    9.426115] e1000e: Copyright(c) 1999
- 2013 Intel Corporation.
Feb 27 13:19:01 localhost kernel: [    9.426266] e1000e 0000:00:19.0:
Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
Feb 27 13:19:01 localhost kernel: [    9.491571] cfg80211: Calling CRDA to
update world regulatory domain
Feb 27 13:19:01 localhost kernel: [    9.494409] tpm_tis 00:09: 1.2 TPM
(device-id 0x0, rev-id 78)
Feb 27 13:19:01 localhost kernel: [    9.495129] Intel(R) Wireless WiFi
driver for Linux, in-tree:d
Feb 27 13:19:01 localhost kernel: [    9.495131] Copyright(c) 2003-2013
Intel Corporation
Feb 27 13:19:01 localhost kernel: [    9.495242] iwlwifi 0000:03:00.0:
can't disable ASPM; OS doesn't have ASPM control
Feb 27 13:19:01 localhost kernel: [    9.566436] tpm_tis 00:09: TPM is
disabled/deactivated (0x6)
Feb 27 13:19:01 localhost kernel: [    9.584966] microcode: CPU0
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.621757] microcode: CPU0
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.622352] microcode: CPU0 updated to
revision 0x19, date = 2013-06-13
Feb 27 13:19:01 localhost kernel: [    9.622358] microcode: CPU1
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.622384] microcode: CPU1
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.622684] microcode: CPU1 updated to
revision 0x19, date = 2013-06-13
Feb 27 13:19:01 localhost kernel: [    9.622699] microcode: CPU2
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.622727] microcode: CPU2
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.623022] microcode: CPU2 updated to
revision 0x19, date = 2013-06-13
Feb 27 13:19:01 localhost kernel: [    9.623028] microcode: CPU3
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.623045] microcode: CPU3
sig=0x306a9, pf=0x10, revision=0x15
Feb 27 13:19:01 localhost kernel: [    9.623349] microcode: CPU3 updated to
revision 0x19, date = 2013-06-13
Feb 27 13:19:01 localhost kernel: [    9.623387] microcode: Microcode
Update Driver: v2.00 <tigran(a)aivazian.fsnet.co.uk&gt;, Peter Oruba
Feb 27 13:19:01 localhost kernel: [    9.641057] alg: No test for crc32
(crc32-pclmul)
Feb 27 13:19:01 localhost kernel: [    9.684579] e1000e 0000:00:19.0 eth0:
registered PHC clock
Feb 27 13:19:01 localhost kernel: [    9.684582] e1000e 0000:00:19.0 eth0:
(PCI Express:2.5GT/s:Width x1) 00:21:cc:d1:0a:db
Feb 27 13:19:01 localhost kernel: [    9.684583] e1000e 0000:00:19.0 eth0:
Intel(R) PRO/1000 Network Connection
Feb 27 13:19:01 localhost kernel: [    9.684634] e1000e 0000:00:19.0 eth0:
MAC: 10, PHY: 11, PBA No: 1000FF-0FF
Feb 27 13:19:01 localhost kernel: [    9.746259] media: Linux media
interface: v0.10
Feb 27 13:19:01 localhost kernel: [    9.748869] Linux video capture
interface: v2.00
Feb 27 13:19:01 localhost kernel: [    9.753457] uvcvideo: Found UVC 1.00
device Integrated Camera (5986:02d5)
Feb 27 13:19:01 localhost kernel: [    9.755783] input: Integrated Camera
as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input14
Feb 27 13:19:01 localhost kernel: [    9.755851] usbcore: registered new
interface driver uvcvideo
Feb 27 13:19:01 localhost kernel: [    9.755853] USB Video Class driver
(1.1.1)
Feb 27 13:19:01 localhost kernel: [    9.827418] iwlwifi 0000:03:00.0:
loaded firmware version 18.168.6.1 op_mode iwldvm
Feb 27 13:19:01 localhost kernel: [   10.139575] iTCO_vendor_support:
vendor-support=0
Feb 27 13:19:01 localhost kernel: [   10.140807] iTCO_wdt: Intel TCO
WatchDog Timer Driver v1.10
Feb 27 13:19:01 localhost kernel: [   10.140841] iTCO_wdt: Found a Panther
Point TCO device (Version=2, TCOBASE=0x0460)
Feb 27 13:19:01 localhost kernel: [   10.141157] iTCO_wdt: initialized.
heartbeat=30 sec (nowayout=0)
Feb 27 13:19:01 localhost kernel: [   10.281856] iwlwifi 0000:03:00.0:
CONFIG_IWLWIFI_DEBUG enabled
Feb 27 13:19:01 localhost kernel: [   10.281859] iwlwifi 0000:03:00.0:
CONFIG_IWLWIFI_DEBUGFS enabled
Feb 27 13:19:01 localhost kernel: [   10.281860] iwlwifi 0000:03:00.0:
CONFIG_IWLWIFI_DEVICE_TRACING disabled
Feb 27 13:19:01 localhost kernel: [   10.281862] iwlwifi 0000:03:00.0:
Detected Intel(R) Centrino(R) Wireless-N 2200 BGN, REV=0x104
Feb 27 13:19:01 localhost kernel: [   10.281968] iwlwifi 0000:03:00.0: L1
Enabled; Disabling L0S
Feb 27 13:19:01 localhost kernel: [   10.415140] cfg80211: World regulatory
domain updated:
Feb 27 13:19:01 localhost kernel: [   10.415144] cfg80211:   (start_freq -
end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Feb 27 13:19:01 localhost kernel: [   10.415145] cfg80211:   (2402000 KHz -
2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Feb 27 13:19:01 localhost kernel: [   10.415147] cfg80211:   (2457000 KHz -
2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Feb 27 13:19:01 localhost kernel: [   10.415148] cfg80211:   (2474000 KHz -
2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Feb 27 13:19:01 localhost kernel: [   10.415149] cfg80211:   (5170000 KHz -
5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Feb 27 13:19:01 localhost kernel: [   10.415150] cfg80211:   (5735000 KHz -
5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Feb 27 13:19:01 localhost kernel: [   10.415151] cfg80211:   (57240000 KHz
- 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
Feb 27 13:19:01 localhost kernel: [   10.919018] thinkpad_acpi: EC reports
that Thermal Table has changed
Feb 27 13:19:01 localhost kernel: [   11.302142] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.302158] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
Feb 27 13:19:01 localhost kernel: [   11.302160] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.302161] Sense Key : Illegal
Request [current]
Feb 27 13:19:01 localhost kernel: [   11.302164] ILI
Feb 27 13:19:01 localhost kernel: [   11.302165] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.302168] Add. Sense: Illegal mode
for this track
Feb 27 13:19:01 localhost kernel: [   11.302169] sr 1:0:0:0: [sr0] CDB:
Feb 27 13:19:01 localhost kernel: [   11.302171] Read(10): 28 00 00 00 80
00 00 00 02 00
Feb 27 13:19:01 localhost kernel: [   11.302177] end_request: I/O error,
dev sr0, sector 131072
Feb 27 13:19:01 localhost kernel: [   11.302179] Buffer I/O error on device
sr0, logical block 16384
Feb 27 13:19:01 localhost kernel: [   11.392937] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.392942] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
Feb 27 13:19:01 localhost kernel: [   11.392944] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.392945] Sense Key : Illegal
Request [current]
Feb 27 13:19:01 localhost kernel: [   11.392947] ILI
Feb 27 13:19:01 localhost kernel: [   11.392949] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.392952] Add. Sense: Illegal mode
for this track
Feb 27 13:19:01 localhost kernel: [   11.392953] sr 1:0:0:0: [sr0] CDB:
Feb 27 13:19:01 localhost kernel: [   11.392954] Read(10): 28 00 00 00 80
00 00 00 02 00
Feb 27 13:19:01 localhost kernel: [   11.392960] end_request: I/O error,
dev sr0, sector 131072
Feb 27 13:19:01 localhost kernel: [   11.392964] Buffer I/O error on device
sr0, logical block 16384
Feb 27 13:19:01 localhost kernel: [   11.619848] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.619853] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
Feb 27 13:19:01 localhost kernel: [   11.619855] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.619857] Sense Key : Illegal
Request [current]
Feb 27 13:19:01 localhost kernel: [   11.619859] ILI
Feb 27 13:19:01 localhost kernel: [   11.619860] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.619863] Add. Sense: Illegal mode
for this track
Feb 27 13:19:01 localhost kernel: [   11.619865] sr 1:0:0:0: [sr0] CDB:
Feb 27 13:19:01 localhost kernel: [   11.619866] Read(10): 28 00 00 00 04
00 00 00 02 00
Feb 27 13:19:01 localhost kernel: [   11.619872] end_request: I/O error,
dev sr0, sector 4096
Feb 27 13:19:01 localhost kernel: [   11.619875] Buffer I/O error on device
sr0, logical block 512
Feb 27 13:19:01 localhost kernel: [   11.753129] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.753143] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
Feb 27 13:19:01 localhost kernel: [   11.753145] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.753147] Sense Key : Illegal
Request [current]
Feb 27 13:19:01 localhost kernel: [   11.753149] ILI
Feb 27 13:19:01 localhost kernel: [   11.753151] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   11.753153] Add. Sense: Illegal mode
for this track
Feb 27 13:19:01 localhost kernel: [   11.753155] sr 1:0:0:0: [sr0] CDB:
Feb 27 13:19:01 localhost kernel: [   11.753156] Read(10): 28 00 00 00 04
00 00 00 02 00
Feb 27 13:19:01 localhost kernel: [   11.753162] end_request: I/O error,
dev sr0, sector 4096
Feb 27 13:19:01 localhost kernel: [   11.753165] Buffer I/O error on device
sr0, logical block 512
Feb 27 13:19:01 localhost kernel: [   12.015268] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   12.015271] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
Feb 27 13:19:01 localhost kernel: [   12.015273] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   12.015274] Sense Key : Illegal
Request [current]
Feb 27 13:19:01 localhost kernel: [   12.015277] ILI
Feb 27 13:19:01 localhost kernel: [   12.015278] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   12.015281] Add. Sense: Illegal mode
for this track
Feb 27 13:19:01 localhost kernel: [   12.015282] sr 1:0:0:0: [sr0] CDB:
Feb 27 13:19:01 localhost kernel: [   12.015283] Read(10): 28 00 00 02 28
08 00 00 02 00
Feb 27 13:19:01 localhost kernel: [   12.015288] end_request: I/O error,
dev sr0, sector 565280
Feb 27 13:19:01 localhost kernel: [   12.015291] Buffer I/O error on device
sr0, logical block 70660
Feb 27 13:19:01 localhost kernel: [   12.082135] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   12.082139] Result: hostbyte=DID_OK
driverbyte=DRIVER_SENSE
Feb 27 13:19:01 localhost kernel: [   12.082140] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   12.082142] Sense Key : Illegal
Request [current]
Feb 27 13:19:01 localhost kernel: [   12.082144] ILI
Feb 27 13:19:01 localhost kernel: [   12.082145] sr 1:0:0:0: [sr0]
Feb 27 13:19:01 localhost kernel: [   12.082148] Add. Sense: Illegal mode
for this track
Feb 27 13:19:01 localhost kernel: [   12.082149] sr 1:0:0:0: [sr0] CDB:
Feb 27 13:19:01 localhost kernel: [   12.082150] Read(10): 28 00 00 02 28
08 00 00 02 00
Feb 27 13:19:01 localhost kernel: [   12.082156] end_request: I/O error,
dev sr0, sector 565280
Feb 27 13:19:01 localhost kernel: [   12.082159] Buffer I/O error on device
sr0, logical block 70660
Feb 27 13:19:01 localhost kernel: [   12.588974] Adding 8011772k swap on
/dev/mapper/fedora-swap.  Priority:-1 extents:1 across:8011772k FS
Feb 27 13:19:01 localhost kernel: [   14.221619] EXT4-fs (sda3): mounted
filesystem with ordered data mode. Opts: (null)
Feb 27 13:19:01 localhost kernel: [   16.733691] ACPI Warning:
\_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI
requires [Package] (20131115/nsarguments-95)
Feb 27 13:19:01 localhost kernel: [   16.734449] ACPI Warning:
\_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI
requires [Package] (20131115/nsarguments-95)
Feb 27 13:19:01 localhost kernel: [   17.283820] thinkpad_acpi: EC reports
that Thermal Table has changed
Feb 27 13:19:01 localhost kernel: [   17.381523] EXT4-fs (dm-2): mounted
filesystem with ordered data mode. Opts: (null)
Feb 27 13:19:01 localhost kernel: [   17.587060] type=1305
audit(1393525115.660:4): audit_pid=651 old=0 auid=4294967295 ses=4294967295
subj=system_u:system_r:auditd_t:s0 res=1
Feb 27 13:19:01 localhost kernel: [   18.388818] nf_conntrack version 0.5.0
(16384 buckets, 65536 max)
Feb 27 13:19:01 localhost kernel: [   18.400216] ip6_tables: (C) 2000-2006
Netfilter Core Team
Feb 27 13:19:01 localhost kernel: [   18.423757] Ebtables v2.0 registered
Feb 27 13:19:01 localhost kernel: [   19.401434] Bridge firewalling
registered
Feb 27 13:19:01 localhost kernel: [   22.105142] thinkpad_acpi: EC reports
that Thermal Table has changed
Feb 27 13:19:01 localhost kernel: [   22.968887] IPv6: ADDRCONF(NETDEV_UP):
em1: link is not ready
Feb 27 13:19:01 localhost kernel: [   22.970787] iwlwifi 0000:03:00.0: L1
Enabled; Disabling L0S
Feb 27 13:19:01 localhost kernel: [   22.978560] iwlwifi 0000:03:00.0:
Radio type=0x2-0x0-0x0
Feb 27 13:19:01 localhost kernel: [   23.217153] iwlwifi 0000:03:00.0: L1
Enabled; Disabling L0S
Feb 27 13:19:01 localhost kernel: [   23.224900] iwlwifi 0000:03:00.0:
Radio type=0x2-0x0-0x0
Feb 27 13:19:01 localhost kernel: [   23.285311] IPv6: ADDRCONF(NETDEV_UP):
wlp3s0: link is not ready
Feb 27 13:19:01 localhost kernel: [   23.961697] Bluetooth: Core ver 2.17
Feb 27 13:19:01 localhost kernel: [   23.961781] NET: Registered protocol
family 31
Feb 27 13:19:01 localhost kernel: [   23.961783] Bluetooth: HCI device and
connection manager initialized
Feb 27 13:19:01 localhost kernel: [   23.961791] Bluetooth: HCI socket
layer initialized
Feb 27 13:19:01 localhost kernel: [   23.961802] Bluetooth: L2CAP socket
layer initialized
Feb 27 13:19:01 localhost kernel: [   23.961808] Bluetooth: SCO socket
layer initialized
Feb 27 13:19:01 localhost kernel: [   24.319328] Bluetooth: BNEP (Ethernet
Emulation) ver 1.3
Feb 27 13:19:01 localhost kernel: [   24.319331] Bluetooth: BNEP filters:
protocol multicast
Feb 27 13:19:01 localhost kernel: [   24.319340] Bluetooth: BNEP socket
layer initialized
Feb 27 13:19:01 localhost kernel: [   37.749497] ACPI Warning:
\_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI
requires [Package] (20131115/nsarguments-95)
Feb 27 13:19:01 localhost kernel: [   37.750518] ACPI Warning:
\_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI
requires [Package] (20131115/nsarguments-95)
Feb 27 13:19:01 localhost kernel: [   38.549896] thinkpad_acpi: EC reports
that Thermal Table has changed
Feb 27 13:19:01 localhost rsyslogd-2027: imjournal: fscanf on state file
`/var/lib/rsyslog/imjournal.state' failed
 [try http://www.rsyslog.com/e/2027 ]
Feb 27 13:19:07 localhost kernel: [   49.799571] wlp3s0: authenticate with
24:de:c6:5b:49:70
Feb 27 13:19:07 localhost kernel: [   49.805327] wlp3s0: send auth to
24:de:c6:5b:49:70 (try 1/3)
Feb 27 13:19:07 localhost kernel: [   49.809693] wlp3s0: authenticated
Feb 27 13:19:07 localhost kernel: [   49.810071] wlp3s0: associate with
24:de:c6:5b:49:70 (try 1/3)
Feb 27 13:19:07 localhost kernel: [   49.815602] wlp3s0: RX AssocResp from
24:de:c6:5b:49:70 (capab=0x421 status=0 aid=1)
Feb 27 13:19:07 localhost kernel: [   49.838824] wlp3s0: associated
Feb 27 13:19:07 localhost kernel: [   49.838872] IPv6:
ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
Feb 27 13:19:09 localhost kernel: [   51.299031] thinkpad_acpi: EC reports
that Thermal Table has changed
Feb 27 13:19:24 localhost kernel: [   67.014352] ACPI Warning:
\_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI
requires [Package] (20131115/nsarguments-95)
Feb 27 13:19:24 localhost kernel: [   67.014983] ACPI Warning:
\_SB_.PCI0.PEG_.VID_._DSM: Argument #4 type mismatch - Found [Buffer], ACPI
requires [Package] (20131115/nsarguments-95)
Feb 27 13:19:25 localhost kernel: [   67.791524] thinkpad_acpi: EC reports
that Thermal Table has changed
Feb 27 13:19:33 localhost kernel: [   75.293764] fuse init (API version
7.22)
Feb 27 13:21:35 localhost rsyslogd: [origin software="rsyslogd"
swVersion="7.4.2" x-pid="693"
x-info="http://www.rsyslog.com"] start

[kevin martin]

On 02/27/2014 12:50 PM, Oliver Ruebenacker wrote:
>  
>       Hello,
>  
>    I'm having multiple hard freezes a day with Fedora 20 on a Lenovo ThinkPad T430.
> Display stops moving, even mouse cursor, with no
>  previous warning. I have the problem since Fedora 19.
>  
>    Any ideas?
>  
>    I'm copying a few lines from /var/log/messages showing lines from some time before
> the crash until the restart (see below).
>  
>    Thanks!
>  
>       Best,
>       Oliver
>  
>  -- 
>  Oliver Ruebenacker
>  Founder at Relomics Consulting <http://www.relomics.com>
>  Be always grateful, but never satisfied.
>  
>  Feb 27 13:19:01 localhost kernel: [    9.397141] thinkpad_acpi: ThinkPad BIOS G1ET73WW
> (2.09 ), EC unknown
>  Feb 27 13:19:01 localhost kernel: [    9.397141] thinkpad_acpi: Lenovo ThinkPad T430,
> model 2342CTO
>  Feb 27 13:19:01 localhost kernel: [    9.397474] thinkpad_acpi: Unsupported brightness
> interface, please contact
>  ibm-acpi-devel(a)lists.sourceforge.net <mailto:[e-mail]>
>  Feb 27 13:19:01 localhost kernel: [    9.397582] thinkpad_acpi: radio switch found;
> radios are enabled
>  Feb 27 13:19:01 localhost kernel: [    9.397591] thinkpad_acpi: This ThinkPad has
> standard ACPI backlight brightness control,
>  supported by the ACPI video driver
>  Feb 27 13:19:01 localhost kernel: [    9.397592] thinkpad_acpi: Disabling thinkpad-acpi
> brightness events by default...
>  Feb 27 13:19:01 localhost kernel: [    9.398576] thinkpad_acpi: Console audio control
> enabled, mode: monitor (read only)
>  Feb 27 13:19:01 localhost kernel: [    9.401050] input: ThinkPad Extra Buttons as
> /devices/platform/thinkpad_acpi/input/input9
>  Feb 27 13:19:01 localhost kernel: [    9.406826] input: HDA Intel PCH Dock Headphone as
>  /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
>  Feb 27 13:19:01 localhost kernel: [    9.406908] input: HDA Intel PCH Headphone as
> /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
>  Feb 27 13:19:01 localhost kernel: [    9.406956] input: HDA Intel PCH Dock Mic as
> /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
>  Feb 27 13:19:01 localhost kernel: [    9.407002] input: HDA Intel PCH Mic as
> /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
>  Feb 27 13:19:01 localhost kernel: [    9.407830] i801_smbus 0000:00:1f.3: SMBus using PCI
> Interrupt
>  Feb 27 13:19:01 localhost kernel: [    9.407917] ACPI Warning:
> 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region
>  \_SB_.PCI0.LPC_.PMIO 1 (20131115/utaddress-251)
>  Feb 27 13:19:01 localhost kernel: [    9.407922] ACPI: If an ACPI driver is available for
> this device, you should use it instead of
>  the native driver
>  Feb 27 13:19:01 localhost kernel: [    9.407929] ACPI Warning:
> 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region
>  \_SB_.PCI0.LPC_.LPIO 1 (20131115/utaddress-251)
>  Feb 27 13:19:01 localhost kernel: [    9.407932] ACPI: If an ACPI driver is available for
> this device, you should use it instead of
>  the native driver
>  Feb 27 13:19:01 localhost kernel: [    9.407933] ACPI Warning:
> 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region
>  \_SB_.PCI0.LPC_.LPIO 1 (20131115/utaddress-251)
>  Feb 27 13:19:01 localhost kernel: [    9.407936] ACPI: If an ACPI driver is available for
> this device, you should use it instead of
>  the native driver
>  Feb 27 13:19:01 localhost kernel: [    9.407938] lpc_ich: Resource conflict(s) found
> affecting gpio_ich
>  Feb 27 13:19:01 localhost kernel: [    9.426112] e1000e: Intel(R) PRO/1000 Network Driver
> - 2.3.2-k
>  Feb 27 13:19:01 localhost kernel: [    9.426115] e1000e: Copyright(c) 1999 - 2013 Intel
> Corporation.
>  Feb 27 13:19:01 localhost kernel: [    9.426266] e1000e 0000:00:19.0: Interrupt
> Throttling Rate (ints/sec) set to dynamic
>  conservative mode
>  Feb 27 13:19:01 localhost kernel: [    9.491571] cfg80211: Calling CRDA to update world
> regulatory domain
>  Feb 27 13:19:01 localhost kernel: [    9.494409] tpm_tis 00:09: 1.2 TPM (device-id 0x0,
> rev-id 78)
>  Feb 27 13:19:01 localhost kernel: [    9.495129] Intel(R) Wireless WiFi driver for Linux,
> in-tree:d
>  Feb 27 13:19:01 localhost kernel: [    9.495131] Copyright(c) 2003-2013 Intel
> Corporation
>  Feb 27 13:19:01 localhost kernel: [    9.495242] iwlwifi 0000:03:00.0: can't disable
> ASPM; OS doesn't have ASPM control
>  Feb 27 13:19:01 localhost kernel: [    9.566436] tpm_tis 00:09: TPM is
> disabled/deactivated (0x6)
>  Feb 27 13:19:01 localhost kernel: [    9.584966] microcode: CPU0 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.621757] microcode: CPU0 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.622352] microcode: CPU0 updated to revision
> 0x19, date = 2013-06-13
>  Feb 27 13:19:01 localhost kernel: [    9.622358] microcode: CPU1 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.622384] microcode: CPU1 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.622684] microcode: CPU1 updated to revision
> 0x19, date = 2013-06-13
>  Feb 27 13:19:01 localhost kernel: [    9.622699] microcode: CPU2 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.622727] microcode: CPU2 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.623022] microcode: CPU2 updated to revision
> 0x19, date = 2013-06-13
>  Feb 27 13:19:01 localhost kernel: [    9.623028] microcode: CPU3 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.623045] microcode: CPU3 sig=0x306a9, pf=0x10,
> revision=0x15
>  Feb 27 13:19:01 localhost kernel: [    9.623349] microcode: CPU3 updated to revision
> 0x19, date = 2013-06-13
>  Feb 27 13:19:01 localhost kernel: [    9.623387] microcode: Microcode Update Driver:
> v2.00 <tigran(a)aivazian.fsnet.co.uk
>  <mailto:[e-mail]>>, Peter Oruba
>  Feb 27 13:19:01 localhost kernel: [    9.641057] alg: No test for crc32 (crc32-pclmul)
>  Feb 27 13:19:01 localhost kernel: [    9.684579] e1000e 0000:00:19.0 eth0: registered PHC
> clock
>  Feb 27 13:19:01 localhost kernel: [    9.684582] e1000e 0000:00:19.0 eth0: (PCI
> Express:2.5GT/s:Width x1) 00:21:cc:d1:0a:db
>  Feb 27 13:19:01 localhost kernel: [    9.684583] e1000e 0000:00:19.0 eth0: Intel(R)
> PRO/1000 Network Connection
>  Feb 27 13:19:01 localhost kernel: [    9.684634] e1000e 0000:00:19.0 eth0: MAC: 10, PHY:
> 11, PBA No: 1000FF-0FF
>  Feb 27 13:19:01 localhost kernel: [    9.746259] media: Linux media interface: v0.10
>  Feb 27 13:19:01 localhost kernel: [    9.748869] Linux video capture interface: v2.00
>  Feb 27 13:19:01 localhost kernel: [    9.753457] uvcvideo: Found UVC 1.00 device
> Integrated Camera (5986:02d5)
>  Feb 27 13:19:01 localhost kernel: [    9.755783] input: Integrated Camera as
>  /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input14
>  Feb 27 13:19:01 localhost kernel: [    9.755851] usbcore: registered new interface driver
> uvcvideo
>  Feb 27 13:19:01 localhost kernel: [    9.755853] USB Video Class driver (1.1.1)
>  Feb 27 13:19:01 localhost kernel: [    9.827418] iwlwifi 0000:03:00.0: loaded firmware
> version 18.168.6.1 op_mode iwldvm
>  Feb 27 13:19:01 localhost kernel: [   10.139575] iTCO_vendor_support: vendor-support=0
>  Feb 27 13:19:01 localhost kernel: [   10.140807] iTCO_wdt: Intel TCO WatchDog Timer
> Driver v1.10
>  Feb 27 13:19:01 localhost kernel: [   10.140841] iTCO_wdt: Found a Panther Point TCO
> device (Version=2, TCOBASE=0x0460)
>  Feb 27 13:19:01 localhost kernel: [   10.141157] iTCO_wdt: initialized. heartbeat=30 sec
> (nowayout=0)
>  Feb 27 13:19:01 localhost kernel: [   10.281856] iwlwifi 0000:03:00.0:
> CONFIG_IWLWIFI_DEBUG enabled
>  Feb 27 13:19:01 localhost kernel: [   10.281859] iwlwifi 0000:03:00.0:
> CONFIG_IWLWIFI_DEBUGFS enabled
>  Feb 27 13:19:01 localhost kernel: [   10.281860] iwlwifi 0000:03:00.0:
> CONFIG_IWLWIFI_DEVICE_TRACING disabled
>  Feb 27 13:19:01 localhost kernel: [   10.281862] iwlwifi 0000:03:00.0: Detected Intel(R)
> Centrino(R) Wireless-N 2200 BGN, REV=0x104
>  Feb 27 13:19:01 localhost kernel: [   10.281968] iwlwifi 0000:03:00.0: L1 Enabled;
> Disabling L0S
>  Feb 27 13:19:01 localhost kernel: [   10.415140] cfg80211: World regulatory domain
> updated:
>  Feb 27 13:19:01 localhost kernel: [   10.415144] cfg80211:   (start_freq - end_freq @
> bandwidth), (max_antenna_gain, max_eirp)
>  Feb 27 13:19:01 localhost kernel: [   10.415145] cfg80211:   (2402000 KHz - 2472000 KHz @
> 40000 KHz), (N/A, 2000 mBm)
>  Feb 27 13:19:01 localhost kernel: [   10.415147] cfg80211:   (2457000 KHz - 2482000 KHz @
> 40000 KHz), (N/A, 2000 mBm)
>  Feb 27 13:19:01 localhost kernel: [   10.415148] cfg80211:   (2474000 KHz - 2494000 KHz @
> 20000 KHz), (N/A, 2000 mBm)
>  Feb 27 13:19:01 localhost kernel: [   10.415149] cfg80211:   (5170000 KHz - 5250000 KHz @
> 80000 KHz), (N/A, 2000 mBm)
>  Feb 27 13:19:01 localhost kernel: [   10.415150] cfg80211:   (5735000 KHz - 5835000 KHz @
> 80000 KHz), (N/A, 2000 mBm)
>  Feb 27 13:19:01 localhost kernel: [   10.415151] cfg80211:   (57240000 KHz - 63720000 KHz
> @ 2160000 KHz), (N/A, 0 mBm)
>  Feb 27 13:19:01 localhost kernel: [   10.919018] thinkpad_acpi: EC reports that Thermal
> Table has changed
>  Feb 27 13:19:01 localhost kernel: [   11.302142] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.302158] Result: hostbyte=DID_OK
> driverbyte=DRIVER_SENSE
>  Feb 27 13:19:01 localhost kernel: [   11.302160] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.302161] Sense Key : Illegal Request [current]
>  Feb 27 13:19:01 localhost kernel: [   11.302164] ILI
>  Feb 27 13:19:01 localhost kernel: [   11.302165] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.302168] Add. Sense: Illegal mode for this track
>  Feb 27 13:19:01 localhost kernel: [   11.302169] sr 1:0:0:0: [sr0] CDB:
>  Feb 27 13:19:01 localhost kernel: [   11.302171] Read(10): 28 00 00 00 80 00 00 00 02 00
>  Feb 27 13:19:01 localhost kernel: [   11.302177] end_request: I/O error, dev sr0, sector
> 131072
>  Feb 27 13:19:01 localhost kernel: [   11.302179] Buffer I/O error on device sr0, logical
> block 16384
>  Feb 27 13:19:01 localhost kernel: [   11.392937] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.392942] Result: hostbyte=DID_OK
> driverbyte=DRIVER_SENSE
>  Feb 27 13:19:01 localhost kernel: [   11.392944] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.392945] Sense Key : Illegal Request [current]
>  Feb 27 13:19:01 localhost kernel: [   11.392947] ILI
>  Feb 27 13:19:01 localhost kernel: [   11.392949] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.392952] Add. Sense: Illegal mode for this track
>  Feb 27 13:19:01 localhost kernel: [   11.392953] sr 1:0:0:0: [sr0] CDB:
>  Feb 27 13:19:01 localhost kernel: [   11.392954] Read(10): 28 00 00 00 80 00 00 00 02 00
>  Feb 27 13:19:01 localhost kernel: [   11.392960] end_request: I/O error, dev sr0, sector
> 131072
>  Feb 27 13:19:01 localhost kernel: [   11.392964] Buffer I/O error on device sr0, logical
> block 16384
>  Feb 27 13:19:01 localhost kernel: [   11.619848] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.619853] Result: hostbyte=DID_OK
> driverbyte=DRIVER_SENSE
>  Feb 27 13:19:01 localhost kernel: [   11.619855] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.619857] Sense Key : Illegal Request [current]
>  Feb 27 13:19:01 localhost kernel: [   11.619859] ILI
>  Feb 27 13:19:01 localhost kernel: [   11.619860] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.619863] Add. Sense: Illegal mode for this track
>  Feb 27 13:19:01 localhost kernel: [   11.619865] sr 1:0:0:0: [sr0] CDB:
>  Feb 27 13:19:01 localhost kernel: [   11.619866] Read(10): 28 00 00 00 04 00 00 00 02 00
>  Feb 27 13:19:01 localhost kernel: [   11.619872] end_request: I/O error, dev sr0, sector
> 4096
>  Feb 27 13:19:01 localhost kernel: [   11.619875] Buffer I/O error on device sr0, logical
> block 512
>  Feb 27 13:19:01 localhost kernel: [   11.753129] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.753143] Result: hostbyte=DID_OK
> driverbyte=DRIVER_SENSE
>  Feb 27 13:19:01 localhost kernel: [   11.753145] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.753147] Sense Key : Illegal Request [current]
>  Feb 27 13:19:01 localhost kernel: [   11.753149] ILI
>  Feb 27 13:19:01 localhost kernel: [   11.753151] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   11.753153] Add. Sense: Illegal mode for this track
>  Feb 27 13:19:01 localhost kernel: [   11.753155] sr 1:0:0:0: [sr0] CDB:
>  Feb 27 13:19:01 localhost kernel: [   11.753156] Read(10): 28 00 00 00 04 00 00 00 02 00
>  Feb 27 13:19:01 localhost kernel: [   11.753162] end_request: I/O error, dev sr0, sector
> 4096
>  Feb 27 13:19:01 localhost kernel: [   11.753165] Buffer I/O error on device sr0, logical
> block 512
>  Feb 27 13:19:01 localhost kernel: [   12.015268] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   12.015271] Result: hostbyte=DID_OK
> driverbyte=DRIVER_SENSE
>  Feb 27 13:19:01 localhost kernel: [   12.015273] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   12.015274] Sense Key : Illegal Request [current]
>  Feb 27 13:19:01 localhost kernel: [   12.015277] ILI
>  Feb 27 13:19:01 localhost kernel: [   12.015278] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   12.015281] Add. Sense: Illegal mode for this track
>  Feb 27 13:19:01 localhost kernel: [   12.015282] sr 1:0:0:0: [sr0] CDB:
>  Feb 27 13:19:01 localhost kernel: [   12.015283] Read(10): 28 00 00 02 28 08 00 00 02 00
>  Feb 27 13:19:01 localhost kernel: [   12.015288] end_request: I/O error, dev sr0, sector
> 565280
>  Feb 27 13:19:01 localhost kernel: [   12.015291] Buffer I/O error on device sr0, logical
> block 70660
>  Feb 27 13:19:01 localhost kernel: [   12.082135] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   12.082139] Result: hostbyte=DID_OK
> driverbyte=DRIVER_SENSE
>  Feb 27 13:19:01 localhost kernel: [   12.082140] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   12.082142] Sense Key : Illegal Request [current]
>  Feb 27 13:19:01 localhost kernel: [   12.082144] ILI
>  Feb 27 13:19:01 localhost kernel: [   12.082145] sr 1:0:0:0: [sr0] 
>  Feb 27 13:19:01 localhost kernel: [   12.082148] Add. Sense: Illegal mode for this track
>  Feb 27 13:19:01 localhost kernel: [   12.082149] sr 1:0:0:0: [sr0] CDB:
>  Feb 27 13:19:01 localhost kernel: [   12.082150] Read(10): 28 00 00 02 28 08 00 00 02 00
>  Feb 27 13:19:01 localhost kernel: [   12.082156] end_request: I/O error, dev sr0, sector
> 565280
>  Feb 27 13:19:01 localhost kernel: [   12.082159] Buffer I/O error on device sr0, logical
> block 70660
>  Feb 27 13:19:01 localhost kernel: [   12.588974] Adding 8011772k swap on
> /dev/mapper/fedora-swap.  Priority:-1 extents:1
>  across:8011772k FS
>  Feb 27 13:19:01 localhost kernel: [   14.221619] EXT4-fs (sda3): mounted filesystem with
> ordered data mode. Opts: (null)
>  Feb 27 13:19:01 localhost kernel: [   16.733691] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM:
> Argument #4 type mismatch - Found
>  [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
>  Feb 27 13:19:01 localhost kernel: [   16.734449] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM:
> Argument #4 type mismatch - Found
>  [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
>  Feb 27 13:19:01 localhost kernel: [   17.283820] thinkpad_acpi: EC reports that Thermal
> Table has changed
>  Feb 27 13:19:01 localhost kernel: [   17.381523] EXT4-fs (dm-2): mounted filesystem with
> ordered data mode. Opts: (null)
>  Feb 27 13:19:01 localhost kernel: [   17.587060] type=1305 audit(1393525115.660:4):
> audit_pid=651 old=0 auid=4294967295
>  ses=4294967295 subj=system_u:system_r:auditd_t:s0 res=1
>  Feb 27 13:19:01 localhost kernel: [   18.388818] nf_conntrack version 0.5.0 (16384
> buckets, 65536 max)
>  Feb 27 13:19:01 localhost kernel: [   18.400216] ip6_tables: (C) 2000-2006 Netfilter Core
> Team
>  Feb 27 13:19:01 localhost kernel: [   18.423757] Ebtables v2.0 registered
>  Feb 27 13:19:01 localhost kernel: [   19.401434] Bridge firewalling registered
>  Feb 27 13:19:01 localhost kernel: [   22.105142] thinkpad_acpi: EC reports that Thermal
> Table has changed
>  Feb 27 13:19:01 localhost kernel: [   22.968887] IPv6: ADDRCONF(NETDEV_UP): em1: link is
> not ready
>  Feb 27 13:19:01 localhost kernel: [   22.970787] iwlwifi 0000:03:00.0: L1 Enabled;
> Disabling L0S
>  Feb 27 13:19:01 localhost kernel: [   22.978560] iwlwifi 0000:03:00.0: Radio
> type=0x2-0x0-0x0
>  Feb 27 13:19:01 localhost kernel: [   23.217153] iwlwifi 0000:03:00.0: L1 Enabled;
> Disabling L0S
>  Feb 27 13:19:01 localhost kernel: [   23.224900] iwlwifi 0000:03:00.0: Radio
> type=0x2-0x0-0x0
>  Feb 27 13:19:01 localhost kernel: [   23.285311] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link
> is not ready
>  Feb 27 13:19:01 localhost kernel: [   23.961697] Bluetooth: Core ver 2.17
>  Feb 27 13:19:01 localhost kernel: [   23.961781] NET: Registered protocol family 31
>  Feb 27 13:19:01 localhost kernel: [   23.961783] Bluetooth: HCI device and connection
> manager initialized
>  Feb 27 13:19:01 localhost kernel: [   23.961791] Bluetooth: HCI socket layer initialized
>  Feb 27 13:19:01 localhost kernel: [   23.961802] Bluetooth: L2CAP socket layer
> initialized
>  Feb 27 13:19:01 localhost kernel: [   23.961808] Bluetooth: SCO socket layer initialized
>  Feb 27 13:19:01 localhost kernel: [   24.319328] Bluetooth: BNEP (Ethernet Emulation) ver
> 1.3
>  Feb 27 13:19:01 localhost kernel: [   24.319331] Bluetooth: BNEP filters: protocol
> multicast
>  Feb 27 13:19:01 localhost kernel: [   24.319340] Bluetooth: BNEP socket layer
> initialized
>  Feb 27 13:19:01 localhost kernel: [   37.749497] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM:
> Argument #4 type mismatch - Found
>  [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
>  Feb 27 13:19:01 localhost kernel: [   37.750518] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM:
> Argument #4 type mismatch - Found
>  [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
>  Feb 27 13:19:01 localhost kernel: [   38.549896] thinkpad_acpi: EC reports that Thermal
> Table has changed
>  Feb 27 13:19:01 localhost rsyslogd-2027: imjournal: fscanf on state file
> `/var/lib/rsyslog/imjournal.state' failed
>   [try http://www.rsyslog.com/e/2027 ]
>  Feb 27 13:19:07 localhost kernel: [   49.799571] wlp3s0: authenticate with
> 24:de:c6:5b:49:70
>  Feb 27 13:19:07 localhost kernel: [   49.805327] wlp3s0: send auth to 24:de:c6:5b:49:70
> (try 1/3)
>  Feb 27 13:19:07 localhost kernel: [   49.809693] wlp3s0: authenticated
>  Feb 27 13:19:07 localhost kernel: [   49.810071] wlp3s0: associate with 24:de:c6:5b:49:70
> (try 1/3)
>  Feb 27 13:19:07 localhost kernel: [   49.815602] wlp3s0: RX AssocResp from
> 24:de:c6:5b:49:70 (capab=0x421 status=0 aid=1)
>  Feb 27 13:19:07 localhost kernel: [   49.838824] wlp3s0: associated
>  Feb 27 13:19:07 localhost kernel: [   49.838872] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0:
> link becomes ready
>  Feb 27 13:19:09 localhost kernel: [   51.299031] thinkpad_acpi: EC reports that Thermal
> Table has changed
>  Feb 27 13:19:24 localhost kernel: [   67.014352] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM:
> Argument #4 type mismatch - Found
>  [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
>  Feb 27 13:19:24 localhost kernel: [   67.014983] ACPI Warning: \_SB_.PCI0.PEG_.VID_._DSM:
> Argument #4 type mismatch - Found
>  [Buffer], ACPI requires [Package] (20131115/nsarguments-95)
>  Feb 27 13:19:25 localhost kernel: [   67.791524] thinkpad_acpi: EC reports that Thermal
> Table has changed
>  Feb 27 13:19:33 localhost kernel: [   75.293764] fuse init (API version 7.22)
>  Feb 27 13:21:35 localhost rsyslogd: [origin software="rsyslogd"
> swVersion="7.4.2" x-pid="693"
> x-info="http://www.rsyslog.com"] start
>  
>  
>   
What is your video driver and does your Xorg.0.log show anything?

I find that I can't run with acceleration turned on with the nouveau driver at all and
I've been loathe to try the nVidia driver
again since I update the kernel fairly often using rawhide and rpmfusion doesn't tend
to keep up.

Kevin

[Joe Zeff]

On 02/27/2014 11:32 AM, Kevin Martin wrote:
>  I find that I can't run with acceleration turned on with the
> nouveau driver at all and I've been loathe to try the nVidia driver
>  again since I update the kernel fairly often using rawhide and rpmfusion doesn't tend
> to keep up. 
Just install akmod-nvidia and it will build a new kmod as needed.

[kevin martin]

On 02/27/2014 02:40 PM, Joe Zeff wrote:
>  On 02/27/2014 11:32 AM, Kevin Martin wrote:
> > I find that I can't run with acceleration turned on with the nouveau driver at
> all and I've been loathe to try the nVidia driver
> > again since I update the kernel fairly often using rawhide and rpmfusion doesn't
> tend to keep up.
>  
>  Just install akmod-nvidia and it will build a new kmod as needed. 
Sometimes
that's true, sometimes it's not. It's not true when kernel versions change
(say from 3.12 to 3.13) and either nVidia
hasn't updated their code to compile for it or rpmfusion hasn't loaded the latest
nVidia drivers.  Then I'm stuck having to go back
to nouveau, blah blah blah...It becomes quite a hassle..Sigh...guess that's what's
meant by bleeding edge!

Kevin

[Joe Zeff]

On 02/27/2014 01:15 PM, Kevin Martin wrote:
>  On 02/27/2014 02:40 PM, Joe Zeff wrote:
> > On 02/27/2014 11:32 AM, Kevin Martin wrote:
> >> I find that I can't run with acceleration turned on with the nouveau driver
> at all and I've been loathe to try the nVidia driver
> >> again since I update the kernel fairly often using rawhide and rpmfusion
> doesn't tend to keep up.
> >
> > Just install akmod-nvidia and it will build a new kmod as needed.
>  Sometimes that's true, sometimes it's not. It's not true when kernel versions
> change (say from 3.12 to 3.13) and either nVidia
>  hasn't updated their code to compile for it or rpmfusion hasn't loaded the latest
> nVidia drivers.  Then I'm stuck having to go back
>  to nouveau, blah blah blah...It becomes quite a hassle..Sigh...guess that's
> what's meant by bleeding edge!
>  
I have both kmod and akmod installed.  That way, if the new kernel and 
the kmod come out together, it's taken care of by the update.  If not, 
it's taken care of as soon as I boot into the new kernel.  So far, I've 
never had this combo fail, and I've been doing it for several years.

[kevin martin]

On 02/27/2014 03:18 PM, Joe Zeff wrote:
>  On 02/27/2014 01:15 PM, Kevin Martin wrote:
> > On 02/27/2014 02:40 PM, Joe Zeff wrote:
> >> On 02/27/2014 11:32 AM, Kevin Martin wrote:
> >>> I find that I can't run with acceleration turned on with the nouveau
> driver at all and I've been loathe to try the nVidia driver
> >>> again since I update the kernel fairly often using rawhide and rpmfusion
> doesn't tend to keep up.
> >>
> >> Just install akmod-nvidia and it will build a new kmod as needed.
> > Sometimes that's true, sometimes it's not. It's not true when kernel
> versions change (say from 3.12 to 3.13) and either nVidia
> > hasn't updated their code to compile for it or rpmfusion hasn't loaded the
> latest nVidia drivers.  Then I'm stuck having to go back
> > to nouveau, blah blah blah...It becomes quite a hassle..Sigh...guess that's
> what's meant by bleeding edge!
> >
>  
>  I have both kmod and akmod installed.  That way, if the new kernel and the kmod come out
> together, it's taken care of by the
>  update.  If not, it's taken care of as soon as I boot into the new kernel.  So far,
> I've never had this combo fail, and I've been
>  doing it for several years. 
So I gave your suggestion a try last night and no joy. 
 Installed kmod and akmods for nvidia, it pulled in the requisite x nvidia
packages, and it just wouldn't run at all.  When I looked to see what was up I
realized that the nvidia module hadn't
loaded...strange, thought I!  So I tried to manually load it with modprobe and received
the error "Error: could not insert 'nvidia'
:Exec format error".  Bummer.  So then I downloaded the nvidia package from nvidia
directly and, no joy, won't compile (I did do a
little looking around and saw some information about patches that needed to be applied to
get nvidia to build on 3.13+ kernels and
tried those patches but the build failed in other places).  So I had to fall back to
nouveau.  Bleah!  Ah well, at least I've got a
functioning (albeit not accelerated) system!

I'm running latest updated rawhide (3.14.0-0.rc4.git0.1).
Kevin

[Oliver Ruebenacker]

     Hello,

  Problem continues. Had at least five hard freezes today. Any advice?

  Thanks!

     Best,
     Oliver



On Fri, Feb 28, 2014 at 8:20 AM, Kevin Martin <ktmdms(a)gmail.com&gt; wrote:

>  On 02/27/2014 03:18 PM, Joe Zeff wrote:
>  > On 02/27/2014 01:15 PM, Kevin Martin wrote:
>  >> On 02/27/2014 02:40 PM, Joe Zeff wrote:
>  >>> On 02/27/2014 11:32 AM, Kevin Martin wrote:
>  >>>> I find that I can't run with acceleration turned on with the
> nouveau
>  driver at all and I've been loathe to try the nVidia driver
>  >>>> again since I update the kernel fairly often using rawhide and
>  rpmfusion doesn't tend to keep up.
>  >>>
>  >>> Just install akmod-nvidia and it will build a new kmod as needed.
>  >> Sometimes that's true, sometimes it's not. It's not true when
> kernel
>  versions change (say from 3.12 to 3.13) and either nVidia
>  >> hasn't updated their code to compile for it or rpmfusion hasn't loaded
>  the latest nVidia drivers.  Then I'm stuck having to go back
>  >> to nouveau, blah blah blah...It becomes quite a hassle..Sigh...guess
>  that's what's meant by bleeding edge!
>  >>
>  >
>  > I have both kmod and akmod installed.  That way, if the new kernel and
>  the kmod come out together, it's taken care of by the
>  > update.  If not, it's taken care of as soon as I boot into the new
>  kernel.  So far, I've never had this combo fail, and I've been
>  > doing it for several years.
>  So I gave your suggestion a try last night and no joy.   Installed kmod
>  and akmods for nvidia, it pulled in the requisite x nvidia
>  packages, and it just wouldn't run at all.  When I looked to see what was
>  up I realized that the nvidia module hadn't
>  loaded...strange, thought I!  So I tried to manually load it with modprobe
>  and received the error "Error: could not insert 'nvidia'
>  :Exec format error".  Bummer.  So then I downloaded the nvidia package
>  from nvidia directly and, no joy, won't compile (I did do a
>  little looking around and saw some information about patches that needed
>  to be applied to get nvidia to build on 3.13+ kernels and
>  tried those patches but the build failed in other places).  So I had to
>  fall back to nouveau.  Bleah!  Ah well, at least I've got a
>  functioning (albeit not accelerated) system!
>
>  I'm running latest updated rawhide (3.14.0-0.rc4.git0.1).
>  Kevin
>  --
>  users mailing list
>  users(a)lists.fedoraproject.org
>  To unsubscribe or change subscription options:
>  https://admin.fedoraproject.org/mailman/listinfo/users
>  Fedora Code of Conduct: http://fedoraproject.org/code-of-conduct
>  Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
>  Have a question? Ask away: http://ask.fedoraproject.org
>  


-- 
Oliver Ruebenacker
Founder at Relomics Consulting <http://www.relomics.com>
Be always grateful, but never satisfied.

[Joe Zeff]

On 03/14/2014 12:31 PM, Oliver Ruebenacker wrote:
>     Problem continues. Had at least five hard freezes today. Any advice? 
If you haven't already, activate the Magic Sysrq key and make sure that 
it works.  If nothing else, it can help you get an orderly reboot, 
instead of needing to power-cycle.  Be warned, though, that when my old 
mobo had trouble, the combos would work during testing, but never when I 
needed them.  Still, that helped me work out that the mobo was the problem.

[Rick Stevens]

On 03/14/2014 12:31 PM, Oliver Ruebenacker issued this missive:
>        Hello,
>
>     Problem continues. Had at least five hard freezes today. Any advice?
>
>     Thanks!
>
>        Best,
>        Oliver
>
>
>
>  On Fri, Feb 28, 2014 at 8:20 AM, Kevin Martin <ktmdms(a)gmail.com
>  <mailto:[e-mail]>> wrote:
>
>      On 02/27/2014 03:18 PM, Joe Zeff wrote:
>       > On 02/27/2014 01:15 PM, Kevin Martin wrote:
>       >> On 02/27/2014 02:40 PM, Joe Zeff wrote:
>       >>> On 02/27/2014 11:32 AM, Kevin Martin wrote:
>       >>>> I find that I can't run with acceleration turned on with the
>      nouveau driver at all and I've been loathe to try the nVidia driver
>       >>>> again since I update the kernel fairly often using rawhide and
>      rpmfusion doesn't tend to keep up.
>       >>>
>       >>> Just install akmod-nvidia and it will build a new kmod as needed.
>       >> Sometimes that's true, sometimes it's not. It's not true when
>      kernel versions change (say from 3.12 to 3.13) and either nVidia
>       >> hasn't updated their code to compile for it or rpmfusion hasn't
>      loaded the latest nVidia drivers.  Then I'm stuck having to go back
>       >> to nouveau, blah blah blah...It becomes quite a
>      hassle..Sigh...guess that's what's meant by bleeding edge!
>       >>
>       >
>       > I have both kmod and akmod installed.  That way, if the new
>      kernel and the kmod come out together, it's taken care of by the
>       > update.  If not, it's taken care of as soon as I boot into the
>      new kernel.  So far, I've never had this combo fail, and I've been
>       > doing it for several years.
>      So I gave your suggestion a try last night and no joy.   Installed
>      kmod and akmods for nvidia, it pulled in the requisite x nvidia
>      packages, and it just wouldn't run at all.  When I looked to see
>      what was up I realized that the nvidia module hadn't
>      loaded...strange, thought I!  So I tried to manually load it with
>      modprobe and received the error "Error: could not insert 'nvidia'
>      :Exec format error".  Bummer.  So then I downloaded the nvidia
>      package from nvidia directly and, no joy, won't compile (I did do a
>      little looking around and saw some information about patches that
>      needed to be applied to get nvidia to build on 3.13+ kernels and
>      tried those patches but the build failed in other places).  So I had
>      to fall back to nouveau.  Bleah!  Ah well, at least I've got a
>      functioning (albeit not accelerated) system!
>
>      I'm running latest updated rawhide (3.14.0-0.rc4.git0.1). 
Not to burst your bubble, but this list deals with F19 and F20, not
rawhide. For rawhide stuff, you need to start posting to the developers
list. It is entirely possible that the kernel module you have is NOT
compatible with a rawhide kernel since the rawhide kernel isn't released
yet.

Also note that you should use either kmod-nvidia or akmod-nvidia, not
both. I use kmod-nvidia for my G86 (Quadro NVS 290) Tesla card. I
specifically use the kmod-nvidia-<kernelversion> module.

As far as loading the module, you should back up your
/etc/X11/xorg.conf and replace it with something like:

	Section "Device"
		Identifier  "Videocard0"
		Driver      "nvidia"
	EndSection

and let X load the module when X starts up.
----------------------------------------------------------------------
- Rick Stevens, Systems Engineer, AllDigital    ricks(a)alldigital.com -
- AIM/Skype: therps2        ICQ: 22643734            Yahoo: origrps2 -
-                                                                    -
- "I was contemplating the immortal words of Socrates when he said,  -
- 'I drank WHAT?'"                   -- Val Kilmer in "Real Genius"
 -
----------------------------------------------------------------------

[Joe Zeff]

On 03/14/2014 01:29 PM, Rick Stevens wrote:
>  Also note that you should use either kmod-nvidia or akmod-nvidia, not
>  both. I use kmod-nvidia for my G86 (Quadro NVS 290) Tesla card. I
>  specifically use the kmod-nvidia-<kernelversion> module. 
I've been using both for several years now with no problems.  If the 
kmod is ready when the kernel is, I get it, and the reboot is quick; if 
not, the reboot takes a little longer as the akmod does its job, and the 
kmod updates when it's ready.  No problems.

[Oliver Ruebenacker]

     Hello,

  Rawhide? As far as I know I have F20 installed. Perhaps something went
wrong when I upgraded from F19 to F20?

     Best,
     Oliver



On Fri, Mar 14, 2014 at 4:29 PM, Rick Stevens <ricks(a)alldigital.com&gt; wrote:

>  On 03/14/2014 12:31 PM, Oliver Ruebenacker issued this missive:
>
> >
> >       Hello,
> >
> >    Problem continues. Had at least five hard freezes today. Any advice?
> >
> >    Thanks!
> >
> >       Best,
> >       Oliver
> >
> >
> >
> > On Fri, Feb 28, 2014 at 8:20 AM, Kevin Martin <ktmdms(a)gmail.com
> > <mailto:[e-mail]>> wrote:
> >
> >     On 02/27/2014 03:18 PM, Joe Zeff wrote:
> >      > On 02/27/2014 01:15 PM, Kevin Martin wrote:
> >      >> On 02/27/2014 02:40 PM, Joe Zeff wrote:
> >      >>> On 02/27/2014 11:32 AM, Kevin Martin wrote:
> >      >>>> I find that I can't run with acceleration turned on with
> the
> >     nouveau driver at all and I've been loathe to try the nVidia driver
> >      >>>> again since I update the kernel fairly often using rawhide and
> >     rpmfusion doesn't tend to keep up.
> >      >>>
> >      >>> Just install akmod-nvidia and it will build a new kmod as needed.
> >      >> Sometimes that's true, sometimes it's not. It's not true
> when
> >     kernel versions change (say from 3.12 to 3.13) and either nVidia
> >      >> hasn't updated their code to compile for it or rpmfusion
> hasn't
> >     loaded the latest nVidia drivers.  Then I'm stuck having to go back
> >      >> to nouveau, blah blah blah...It becomes quite a
> >     hassle..Sigh...guess that's what's meant by bleeding edge!
> >      >>
> >      >
> >      > I have both kmod and akmod installed.  That way, if the new
> >     kernel and the kmod come out together, it's taken care of by the
> >      > update.  If not, it's taken care of as soon as I boot into the
> >     new kernel.  So far, I've never had this combo fail, and I've been
> >      > doing it for several years.
> >     So I gave your suggestion a try last night and no joy.   Installed
> >     kmod and akmods for nvidia, it pulled in the requisite x nvidia
> >     packages, and it just wouldn't run at all.  When I looked to see
> >     what was up I realized that the nvidia module hadn't
> >     loaded...strange, thought I!  So I tried to manually load it with
> >     modprobe and received the error "Error: could not insert 'nvidia'
> >     :Exec format error".  Bummer.  So then I downloaded the nvidia
> >     package from nvidia directly and, no joy, won't compile (I did do a
> >     little looking around and saw some information about patches that
> >     needed to be applied to get nvidia to build on 3.13+ kernels and
> >     tried those patches but the build failed in other places).  So I had
> >     to fall back to nouveau.  Bleah!  Ah well, at least I've got a
> >     functioning (albeit not accelerated) system!
> >
> >     I'm running latest updated rawhide (3.14.0-0.rc4.git0.1).
> >
>
>  Not to burst your bubble, but this list deals with F19 and F20, not
>  rawhide. For rawhide stuff, you need to start posting to the developers
>  list. It is entirely possible that the kernel module you have is NOT
>  compatible with a rawhide kernel since the rawhide kernel isn't released
>  yet.
>
>  Also note that you should use either kmod-nvidia or akmod-nvidia, not
>  both. I use kmod-nvidia for my G86 (Quadro NVS 290) Tesla card. I
>  specifically use the kmod-nvidia-<kernelversion> module.
>
>  As far as loading the module, you should back up your
>  /etc/X11/xorg.conf and replace it with something like:
>
>          Section "Device"
>                  Identifier  "Videocard0"
>                  Driver      "nvidia"
>          EndSection
>
>  and let X load the module when X starts up.
>  ----------------------------------------------------------------------
>  - Rick Stevens, Systems Engineer, AllDigital    ricks(a)alldigital.com -
>  - AIM/Skype: therps2        ICQ: 22643734            Yahoo: origrps2 -
>  -                                                                    -
>  - "I was contemplating the immortal words of Socrates when he said,  -
>  - 'I drank WHAT?'"                   -- Val Kilmer in "Real
> Genius"  -
>  ----------------------------------------------------------------------
>
>  --
>  users mailing list
>  users(a)lists.fedoraproject.org
>  To unsubscribe or change subscription options:
>  https://admin.fedoraproject.org/mailman/listinfo/users
>  Fedora Code of Conduct: http://fedoraproject.org/code-of-conduct
>  Guidelines: http://fedoraproject.org/wiki/Mailing_list_guidelines
>  Have a question? Ask away: http://ask.fedoraproject.org
>  


-- 
Oliver Ruebenacker
Founder at Relomics Consulting <http://www.relomics.com>
Be always grateful, but never satisfied.

[John Pilkington]

On 14/03/14 20:44, Oliver Ruebenacker wrote:
>        Hello,
>
>     Rawhide? As far as I know I have F20 installed. Perhaps something
>  went wrong when I upgraded from F19 to F20?
>
>        Best,
>        Oliver 
Not you:  The rawhide ref was from Kevin Martin.