Re: no printout, but no other hint of error. F18.
by William Mattison
> Also, the line:
>
> May 13 16:26:14 c-69-138-198-76 cupsd[625]: p11-kit: couldn't open
>
> config file: /root/.pkcs11/pkcs11.conf: Permission denied
>
> from your lpstat output may not be causing a problem, but you should
> address it anyway because until you do you won't know if it's part
> of the problem or not.
Ummmmmm......
There is no directory "/root/.pkcs11/". The permissions on directory
"/root/" are "dr-xr-x---". I added write permissions for user and
group, then I rebooted the system and turned on the printer. "lpstat -t" now gives:
=============== begin
bash.1[~]: lpstat -t
scheduler is running
no system default destination
device for Xerox_WorkCentre_6015NI: usb://Xerox/WorkCentre%206015NI?serial=BD1580153&interface=1
Xerox_WorkCentre_6015NI accepting requests since Wed 15 May 2013 12:22:30 PM EDT
printer Xerox_WorkCentre_6015NI is idle. enabled since Wed 15 May 2013 12:22:30 PM EDT
bash.2[~]:
=============== end
But there's still no directory "/root/.pkcs11/"!
>>> I couldn't make sense of anything in this directory. Might
>>> something here help?
>>
>> Try this: run tail /var/log/cups/error_log before and after
>> printing, and see if anything new shows up.
>
> Rather than using that command "before and after", you should do:
>
> tail -f /var/log/cups/error_log
>
> before you try to print. it will display all the log lines as it
> goes (stop it when your printing event stops logging). The
> previously suggested commands will only get you the last 10 lines
> (with the lines before you try to print being mostly irrelevant to
> the immediate event), so running it after will miss anything
> relevant that's more than 10 lines back.
I did this:
=============== begin
bash.2[~]: cat -n testprint.txt
1
2 A very short test text file for testing the printer.
3
bash.3[~]: lp testprint.txt -d Xerox_WorkCentre_6015NI
request id is Xerox_WorkCentre_6015NI-19 (1 file(s))
bash.4[~]:
=============== end
The tail -f generated a lot of output:
=============== begin
bash.1[~]: cd /var/log/cups/
bash.2[cups]: tail -f error_log
D [14/May/2013:21:10:44 -0400] [Job 18] printer-state-message="Sending data to printer."
D [14/May/2013:21:10:44 -0400] [Job 18] printer-state-reasons=none
E [14/May/2013:21:15:47 -0400] [Job 18] Stopping unresponsive job!
E [14/May/2013:21:26:34 -0400] Failed to update TXT record for Xerox WorkCentre 6015NI @ c-69-138-198-76.hsd1.md.comcast.net: -2
E [15/May/2013:11:38:09 -0400] Unknown directive JobPrivateAccess on line 88 of /etc/cups/cupsd.conf.
E [15/May/2013:11:38:09 -0400] Unknown directive JobPrivateValues on line 89 of /etc/cups/cupsd.conf.
E [15/May/2013:11:38:09 -0400] Unknown directive SubscriptionPrivateAccess on line 90 of /etc/cups/cupsd.conf.
E [15/May/2013:11:38:09 -0400] Unknown directive SubscriptionPrivateValues on line 91 of /etc/cups/cupsd.conf.
W [15/May/2013:11:38:11 -0400] failed to find device: cups-Xerox_WorkCentre_6015NI
E [15/May/2013:12:22:30 -0400] Failed to update TXT record for Xerox WorkCentre 6015NI @ c-69-138-198-76.hsd1.md.comcast.net: -2
---> {"lp" command issued at this point}
E [15/May/2013:12:28:38 -0400] [Job 19] Job stopped due to filter errors; please consult the error_log file for details.
D [15/May/2013:12:28:38 -0400] [Job 19] The following messages were recorded from 12:28:29 PM to 12:28:37 PM
D [15/May/2013:12:28:38 -0400] [Job 19] Adding start banner page "none".
D [15/May/2013:12:28:38 -0400] [Job 19] Queued on "Xerox_WorkCentre_6015NI" by "root".
D [15/May/2013:12:28:38 -0400] [Job 19] Auto-typing file...
D [15/May/2013:12:28:38 -0400] [Job 19] Request file type is text/plain.
D [15/May/2013:12:28:38 -0400] [Job 19] File of type text/plain queued by "root".
D [15/May/2013:12:28:38 -0400] [Job 19] Adding end banner page "none".
D [15/May/2013:12:28:38 -0400] [Job 19] job-sheets=none,none
D [15/May/2013:12:28:38 -0400] [Job 19] argv[0]="Xerox_WorkCentre_6015NI"
D [15/May/2013:12:28:38 -0400] [Job 19] argv[1]="19"
D [15/May/2013:12:28:38 -0400] [Job 19] argv[2]="root"
D [15/May/2013:12:28:38 -0400] [Job 19] argv[3]="testprint.txt"
D [15/May/2013:12:28:38 -0400] [Job 19] argv[4]="1"
D [15/May/2013:12:28:38 -0400] [Job 19] argv[5]="finishings=3 number-up=1 job-uuid=urn:uuid:b64612fa-9ef2-34b2-5660-d9413ecfd992 job-originating-host-name=localhost time-at-creation=1368635309 time-at-processing=1368635309"
D [15/May/2013:12:28:38 -0400] [Job 19] argv[6]="/var/spool/cups/d00019-001"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[0]="CUPS_CACHEDIR=/var/cache/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[1]="CUPS_DATADIR=/usr/share/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[2]="CUPS_DOCROOT=/usr/share/cups/www"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[3]="CUPS_FONTPATH=/usr/share/cups/fonts"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[4]="CUPS_REQUESTROOT=/var/spool/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[5]="CUPS_SERVERBIN=/usr/lib/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[6]="CUPS_SERVERROOT=/etc/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[7]="CUPS_STATEDIR=/var/run/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[8]="HOME=/var/spool/cups/tmp"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[9]="PATH=/usr/lib/cups/filter:/usr/lib64/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[10]="SERVER_ADMIN=root(a)c-69-138-198-76.hsd1.md.comcast.net"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[11]="SOFTWARE=CUPS/1.5.4"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[12]="TMPDIR=/var/spool/cups/tmp"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[13]="USER=root"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[14]="CUPS_MAX_MESSAGE=2047"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[15]="CUPS_SERVER=/var/run/cups/cups.sock"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[16]="CUPS_ENCRYPTION=IfRequested"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[17]="IPP_PORT=631"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[18]="CHARSET=utf-8"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[19]="LANG=en_US.UTF-8"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[20]="PPD=/etc/cups/ppd/Xerox_WorkCentre_6015NI.ppd"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[21]="RIP_MAX_CACHE=128m"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[22]="CONTENT_TYPE=text/plain"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[23]="DEVICE_URI=usb://Xerox/WorkCentre%206015NI?serial=BD1580153&interface=1"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[24]="PRINTER_INFO=Xerox WorkCentre 6015NI"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[25]="PRINTER_LOCATION=home"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[26]="PRINTER=Xerox_WorkCentre_6015NI"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[27]="PRINTER_STATE_REASONS=none"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[28]="CUPS_FILETYPE=document"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[29]="FINAL_CONTENT_TYPE=printer/Xerox_WorkCentre_6015NI"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[30]="AUTH_I****"
D [15/May/2013:12:28:38 -0400] [Job 19] Started filter /usr/lib/cups/filter/texttopaps (PID 2470)
D [15/May/2013:12:28:38 -0400] [Job 19] Started filter /usr/lib/cups/filter/pstops (PID 2471)
D [15/May/2013:12:28:38 -0400] [Job 19] Started filter /usr/lib/cups/filter/gstoraster (PID 2472)
D [15/May/2013:12:28:38 -0400] [Job 19] Started filter /usr/lib/cups/filter/xrhk2ap (PID 2473)
D [15/May/2013:12:28:38 -0400] [Job 19] Started backend /usr/lib/cups/backend/usb (PID 2474)
D [15/May/2013:12:28:38 -0400] [Job 19] Printing on printer with URI: usb://Xerox/WorkCentre%206015NI?serial=BD1580153&interface=1
D [15/May/2013:12:28:38 -0400] [Job 19] libusb_get_device_list=11
D [15/May/2013:12:28:38 -0400] [Job 19] Page = 612x792; 12,12 to 600,780
D [15/May/2013:12:28:38 -0400] [Job 19] slow_collate=0, slow_duplex=0, slow_order=0
D [15/May/2013:12:28:38 -0400] [Job 19] Before copy_comments - %!PS-Adobe-3.0
D [15/May/2013:12:28:38 -0400] [Job 19] %!PS-Adobe-3.0
D [15/May/2013:12:28:38 -0400] [Job 19] %cupsRotation: 0
D [15/May/2013:12:28:38 -0400] [Job 19] %%Title: testprint.txt
D [15/May/2013:12:28:38 -0400] [Job 19] %%Creator: paps version 0.6.7 by Dov Grobgeld
D [15/May/2013:12:28:38 -0400] [Job 19] %%Pages: (atend)
D [15/May/2013:12:28:38 -0400] [Job 19] %%BoundingBox: 0 0 612 792
D [15/May/2013:12:28:38 -0400] [Job 19] %%For: root
D [15/May/2013:12:28:38 -0400] [Job 19] %%Orientation: Portrait
D [15/May/2013:12:28:38 -0400] [Job 19] %%EndComments
D [15/May/2013:12:28:38 -0400] [Job 19] Before copy_prolog - %%BeginProlog
D [15/May/2013:12:28:38 -0400] [Job 19] Before copy_setup - %%BeginSetup
D [15/May/2013:12:28:38 -0400] [Job 19] Before page loop - %%Page: 1 1
D [15/May/2013:12:28:38 -0400] [Job 19] Copying page 1...
D [15/May/2013:12:28:38 -0400] [Job 19] pagew = 588.8, pagel = 768.8
D [15/May/2013:12:28:38 -0400] [Job 19] bboxx = 0, bboxy = 0, bboxw = 612, bboxl = 792
D [15/May/2013:12:28:38 -0400] [Job 19] PageLeft = 11.6, PageRight = 600.4
D [15/May/2013:12:28:38 -0400] [Job 19] PageTop = 780.4, PageBottom = 11.6
D [15/May/2013:12:28:38 -0400] [Job 19] PageWidth = 612.0, PageLength = 792.0
D [15/May/2013:12:28:38 -0400] [Job 19] Wrote 1 pages...
D [15/May/2013:12:28:38 -0400] [Job 19] PPD uses qualifier 'Gray.Plain.600dpi'
D [15/May/2013:12:28:38 -0400] [Job 19] Calling FindDeviceById(Xerox_WorkCentre_6015NI)
D [15/May/2013:12:28:38 -0400] [Job 19] Failed to send: org.freedesktop.ColorManager.NotFound:device id 'Xerox_WorkCentre_6015NI' does not exists
D [15/May/2013:12:28:38 -0400] [Job 19] Failed to get profile filename!
D [15/May/2013:12:28:38 -0400] [Job 19] no profiles specified in PPD
D [15/May/2013:12:28:38 -0400] [Job 19] Set job-printer-state-message to "no profiles specified in PPD", current level=INFO
D [15/May/2013:12:28:38 -0400] [Job 19] Ghostscript command line: /usr/bin/gs -dQUIET -dPARANOIDSAFER -dNOPAUSE -dBATCH -dNOINTERPOLATE -dNOMEDIAATTRS -sDEVICE=cups -sstdout=%stderr -sOutputFile=%stdout -I/usr/share/cups/fonts -c -f -_
D [15/May/2013:12:28:38 -0400] [Job 19] envp[0]="CUPS_CACHEDIR=/var/cache/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[1]="CUPS_DATADIR=/usr/share/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[2]="CUPS_DOCROOT=/usr/share/cups/www"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[3]="CUPS_FONTPATH=/usr/share/cups/fonts"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[4]="CUPS_REQUESTROOT=/var/spool/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[5]="CUPS_SERVERBIN=/usr/lib/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[6]="CUPS_SERVERROOT=/etc/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[7]="CUPS_STATEDIR=/var/run/cups"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[8]="HOME=/var/spool/cups/tmp"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[9]="PATH=/usr/lib/cups/filter:/usr/lib64/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[10]="SERVER_ADMIN=root(a)c-69-138-198-76.hsd1.md.comcast.net"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[11]="SOFTWARE=CUPS/1.5.4"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[12]="TMPDIR=/var/spool/cups/tmp"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[13]="USER=root"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[14]="CUPS_MAX_MESSAGE=2047"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[15]="CUPS_SERVER=/var/run/cups/cups.sock"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[16]="CUPS_ENCRYPTION=IfRequested"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[17]="IPP_PORT=631"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[18]="CHARSET=utf-8"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[19]="LANG=en_US.UTF-8"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[20]="PPD=/etc/cups/ppd/Xerox_WorkCentre_6015NI.ppd"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[21]="RIP_MAX_CACHE=128m"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[22]="CONTENT_TYPE=text/plain"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[23]="DEVICE_URI=usb://Xerox/WorkCentre%206015NI?serial=BD1580153&interface=1"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[24]="PRINTER_INFO=Xerox WorkCentre 6015NI"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[25]="PRINTER_LOCATION=home"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[26]="PRINTER=Xerox_WorkCentre_6015NI"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[27]="PRINTER_STATE_REASONS=none"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[28]="CUPS_FILETYPE=document"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[29]="FINAL_CONTENT_TYPE=printer/Xerox_WorkCentre_6015NI"
D [15/May/2013:12:28:38 -0400] [Job 19] envp[30]="AUTH_INFO_REQUIRED=none"
D [15/May/2013:12:28:38 -0400] [Job 19] Xerox_WorkCentre_6015NI: error while loading shared libraries: libcups.so.2: cannot open shared object file: No such file or directory
D [15/May/2013:12:28:38 -0400] [Job 19] STATE: +connecting-to-device
D [15/May/2013:12:28:38 -0400] [Job 19] STATE: -connecting-to-device
D [15/May/2013:12:28:38 -0400] [Job 19] Printer found with device ID: MFG:Xerox;CMD:HBPL;MDL:WorkCentre 6015NI;CLS:PRINTER;DES:Xerox WorkCentre 6015NI;STS:L1teYAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAABAAAAAABwAAAAAQAEBP8JBQUJ9wUEAAAAAAAAAAAAAAAA; Device URI: usb://Xerox/WorkCentre%206015NI?serial=BD1580153&interface=1
D [15/May/2013:12:28:38 -0400] [Job 19] Device protocol: 2
D [15/May/2013:12:28:38 -0400] [Job 19] Sending data to printer.
D [15/May/2013:12:28:38 -0400] [Job 19] Sent 0 bytes...
D [15/May/2013:12:28:38 -0400] [Job 19] Start rendering...
D [15/May/2013:12:28:38 -0400] [Job 19] Processing page 1...
D [15/May/2013:12:28:38 -0400] [Job 19] Waiting for read thread to exit...
D [15/May/2013:12:28:38 -0400] [Job 19] Read thread still active, aborting the pending read...
D [15/May/2013:12:28:38 -0400] [Job 19] End of messages
D [15/May/2013:12:28:38 -0400] [Job 19] printer-state=3(idle)
D [15/May/2013:12:28:38 -0400] [Job 19] printer-state-message="Processing page 1..."
D [15/May/2013:12:28:38 -0400] [Job 19] printer-state-reasons=none
E [15/May/2013:12:33:40 -0400] [Job 19] Stopping unresponsive job!
^C
bash.3[cups]:
=============== end
thanks,
Bill.
11 years
combining files and testing results
by Frank Murphy
Having looked at "man join" wasn't sure of it's use here.
Unknown number of files, constant is extension .list
(For testing purposes only using two)
cat *.list >> output.joined | sort -u
How can I test if the output.joined,
is indeed the combined two lists with dupes removed.
--
Regards,
Frank - I check for new mail app. 20min
www.frankly3d.com
11 years
dar is missing from EPEL 6
by MegaBrutal
Hello,
I'm a CentOS user.
I see "dar" is not included in EPEL 6, while it is there in EPEL 5. I
suppose it's left out of EPEL 6 by mistake. Please anyone who has the
authority to do so, fix it!
I also can't find "dar" in other repositories. If I download it from
EPEL 5, I can't install it because of missing depedency
(libcrypto.so.6). Compiling dar from source is Hell. So I really need
an up-to-date "dar" package which is compatible with CentOS 6.4.
Regards,
MegaBrutal
11 years
Can anyone recommend a cheap MP3 player?
by Anthony
I have an old iPod Touch 1st Gen that I really still use quite a bit
(mostly for email and the like). But since I moved all of my computers
to Linux, I can't access the device anymore and can't transfer music to
and from it. I'm not willing to install Windows in any form be it a VM
or the like, So I'm going to get a new MP3 player and just use the Touch
like a handheld for email and podcasts I can stream online.
Can anyone recommend a good, cheap 8gb MP3 player that will work with
Fedora? If possible, I'd like something that simply shows up as a flash
drive or something instead of having the need to install libraries and
other programs to access it.
Thanks!
Anthony Papillion
11 years
Re: no printout, but no other hint of error. F18.
by William Mattison
> Do you see any errors in /var/log/messages pertaining to cups? Does
> "lpstat -t" show the printer and is it enabled?
>
> Kevin
Here's what I have/get, right after re-booting and trying an "lp" command:
[root@c-69-138-198-76 ~]# cd /var/log
[root@c-69-138-198-76 log]# lpstat -t
scheduler is running
no system default destination
device for Xerox_WorkCentre_6015NI: usb://Xerox/WorkCentre%206015NI?serial=BD1580153&interface=1
Xerox_WorkCentre_6015NI accepting requests since Tue 14 May 2013 04:46:41 PM EDT
printer Xerox_WorkCentre_6015NI is idle. enabled since Tue 14 May 2013 04:46:41 PM EDT
Processing page 1...
Xerox_WorkCentre_6015NI-15 root 1024 Tue 14 May 2013 04:46:32 PM EDT
[root@c-69-138-198-76 log]# grep -i cups messages
May 13 16:26:13 c-69-138-198-76 colord: Device added: cups-WorkCentre-6015NI
May 13 16:26:13 c-69-138-198-76 colord: Device added: cups-Xerox_WorkCentre_6015NI
May 13 16:26:14 c-69-138-198-76 cupsd[625]: p11-kit: couldn't open config file: /root/.pkcs11/pkcs11.conf: Permission denied
May 13 22:14:22 c-69-138-198-76 systemd[1]: Stopping CUPS Printing Service...
May 14 05:24:56 c-69-138-198-76 colord: Device added: cups-WorkCentre-6015NI
May 14 05:24:56 c-69-138-198-76 colord: Device added: cups-Xerox_WorkCentre_6015NI
May 14 05:24:57 c-69-138-198-76 cupsd[621]: p11-kit: couldn't open config file: /root/.pkcs11/pkcs11.conf: Permission denied
May 14 09:28:16 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:28:45 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:29:12 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:29:24 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:29:24 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:29:27 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:29:33 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:29:34 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 09:30:08 c-69-138-198-76 systemd[1]: Stopping CUPS Printing Service...
May 14 05:30:52 c-69-138-198-76 colord: Device added: cups-WorkCentre-6015NI
May 14 05:30:52 c-69-138-198-76 colord: Device added: cups-Xerox_WorkCentre_6015NI
May 14 05:30:52 c-69-138-198-76 cupsd[610]: p11-kit: couldn't open config file: /root/.pkcs11/pkcs11.conf: Permission denied
May 14 05:46:48 c-69-138-198-76 colord: Device added: cups-WorkCentre-6015NI
May 14 05:46:48 c-69-138-198-76 colord: Device added: cups-Xerox_WorkCentre_6015NI
May 14 05:46:48 c-69-138-198-76 cupsd[613]: p11-kit: couldn't open config file: /root/.pkcs11/pkcs11.conf: Permission denied
May 14 10:26:02 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 10:28:47 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 13:08:56 c-69-138-198-76 systemd[1]: Stopping CUPS Printing Service...
May 14 11:15:49 c-69-138-198-76 colord: Device added: cups-WorkCentre-6015NI
May 14 11:15:49 c-69-138-198-76 colord: Device added: cups-Xerox_WorkCentre_6015NI
May 14 11:15:49 c-69-138-198-76 cupsd[630]: p11-kit: couldn't open config file: /root/.pkcs11/pkcs11.conf: Permission denied
May 14 15:48:00 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 15:48:20 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 16:23:10 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 16:23:20 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 16:33:11 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 16:33:14 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 16:33:28 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 12:40:54 c-69-138-198-76 colord: Device added: cups-Xerox_WorkCentre_6015NI
May 14 12:40:54 c-69-138-198-76 cupsd[642]: p11-kit: couldn't open config file: /root/.pkcs11/pkcs11.conf: Permission denied
May 14 16:46:32 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
May 14 16:46:42 c-69-138-198-76 systemd[1]: Started CUPS Printing Service.
[root@c-69-138-198-76 log]# pwd
/var/log
[root@c-69-138-198-76 log]#
There is also a directory "/var/log/cups":
[root@c-69-138-198-76 cups]# pwd
/var/log/cups
[root@c-69-138-198-76 cups]# ls -l
total 144
-rw-------. 1 root lp 8546 May 14 16:46 access_log
-rw-------. 1 root lp 16003 Apr 21 17:54 access_log-20130421
-rw-------. 1 root lp 10057 Apr 29 17:11 access_log-20130429
-rw-------. 1 root lp 10178 May 5 15:52 access_log-20130505
-rw-------. 1 root lp 5566 May 13 09:38 access_log-20130513
-rw-------. 1 root lp 27459 May 14 16:46 error_log
-rw-------. 1 root lp 22946 Apr 21 13:54 error_log-20130421
-rw-------. 1 root lp 9962 Apr 29 12:12 error_log-20130429
-rw-------. 1 root lp 10331 May 5 11:51 error_log-20130505
-rw-------. 1 root lp 6446 May 13 05:35 error_log-20130513
-rw-------. 1 root lp 0 Mar 17 20:44 page_log
[root@c-69-138-198-76 cups]#
I couldn't make sense of anything in this directory. Might something here help?
Another question: How do I set the default destination?
thanks,
Bill.
11 years
Cannot save with ISO-8859-15 character encoding
by Paul Smith
Dear All,
I have used gedit for several times on the same document, but I am now
getting the following error while saving the file:
Could not save the file /home/psmith/psmith.htm using the Western
(ISO-8859-15) character encoding.
Is it possible to save the file with the ISO-8859-15 character encoding?
Thanks in advance,
Paul
11 years
Can't start in graphical mode or select desktop after software uninstall
by Anthony
So I wanted to remove libimobiledevices since I *though* I was the one
who'd installed it and it was no longer needed (I'm ditching the iPod).
I typed
sudo yum remove blahblah
where blahblah was the actual package name for libimobiledevices.
All of a sudden, I saw it removing all sorts of stuff I didn't want to:
blueman, banshee, empathy, etc. It then dropped me to a terminal screen
where it had started blueman again. It stayed there.
Finally, I restarted the computer and it only starts at runlevel 3
(non-graphical mode). I have to log in and type startx every time to
bring up the desktop. BUT, it only automatically starts GNOME3 and not
XFCE. I also have no way to select XFCE as I no longer get the login
screen in graphical mode. It just starts the desktop.
How can I fix this? Did I just do something that will require me to
reinstall my system?
Oh, I also tried to do
sudo yum install libimobiledevices and it told me that it was already
installed.
Help, please!
Anthony
11 years
Re: [Yum] $rleassever $basearch from where?
by Frank Murphy
Apology for self reply.
Slight problem:
even though, have changed
/usr/lib/yum-plugins/my_local.py
to point to:
/var/cache/yum/$releasever/$basearch/my_local/packages
left repodir commented out in /etc/yum/pluginconf.d/my_local.conf
it saved some test updates to literally:
/var/cache/yum/$releasever/$basearch/_my_local/packages
it created (due to createrepo=enabled)
/etc/yum.repos.d/_my_local.repo
baseurl=file:/var/cache/yum/$releasever/$basearch/_my_local/packages
cat /var/log/messages shows nothing,
I did "> /var/log/messages" before test.
any debugging pointers.
--
Regards,
Frank - I check for new mail app. 20min
www.frankly3d.com
11 years
Re: [Samba] Samba 4 Packages Available for Download
by Fernando Lozano
Hi there,
[Sorry for cross-posting, I hope I didn't violated any list policies]
> this is just a heads-up that SerNet does provide Samba 4 packages
> (including AD DC package) now.
It was told on the fedora user's list that the kerberos implementation
used by Fedora, RHEL and CentOS conflicts with the samba one, and so
Fedora was providing samba4 binaries without AD DC support. This was
related to the use of FreeIPA by Fedora and RHEL.
So I wasn't expecting to see packages with AD DC support for RHEL and
CentOS so soon. Thanks a lot!
But how did you manage the kerberos problem? I see you repo provides
only samba4 packages, and do not replace any other library or daemin
from CentOS and RHEL.
Or would the problem be present only on newer Fedora releases, and not
on RHEL6 (yet)? Would this be related to the fact servnet does not
provide samba4 packages for Fedora, or you simply don't package anything
for Fedora?
Another question: if my CentOS server is using samba3 from sernet repos,
may I upgrade them using sernet samba4? Or should I uninstall samba3 and
do a clean install of samba4, redoing all configuration manually?
[]s, Fernando Lozano
11 years
(no subject)
by Jackson Byers
Re: f17 printing stalls
Joe Zeff responded:
>>On 05/13/2013 11:18 AM, jackson byers wrote:
>>reboot to my old f16, printing works continually.
> From what you wrote, you upgraded from F 16 to 17, so there's no "old
f16" to
>boot into. I presume that what you meant is that you boot using the last
F 16 >kernel installed. If so, that suggests that something in the new
kernel is >causing the difficulty.
No, I obviously wasn't complete in saying what I did:
I first made backup copy of my f16
and then did the preupgrade from that f16copy.
>Try this: boot into the newer kernel, print a test page, then look at the
most >recent entries in /var/log/cups/error_log. Try to print again and
check again. >You might find something there that points in the right
direction.
I uname -r
3.8.11-100.fc17.i686.PAE
this is the one and only kernel that the preupgrade provided.
I will look at /var/log/cups/error_log
th;anks for response
Jack
11 years
