This refers to a fresh install of Fedora 30 (Xfce spin) on a laptop
that was previously running F25 with no problems.
Install took place using a hardwire connection.
After install, /etc/hosts was updated and the wifi using the GUI
Using the instructions in
https://www.blackmoreops.com/2014/09/18/connect-to-wifi-network-from-comm...
here's what I have. I've verified that the MAC address of the router is
correct.
The password supplied is the network password.
Suggestions for further diagnostics and/or a fix will be greatly
appreciated.
# iw dev
phy#0
Unnamed/non-netdev interface
wdev 0x2
addr a0:a8:cd:ed:9a:09
type P2P-device
txpower 0.00 dBm
Interface wlp3s0
ifindex 3
wdev 0x1
addr 2e:f0:d8:c5:1e:3e
type managed
txpower 0.00 dBm
# ip link set wlp3s0 up
# iw wlp3s0 scan
BSS e4:f4:c6:14:f9:1f(on wlp3s0)
last seen: 297.765s [boottime]
TSF: 10805719880 usec (0d, 03:00:05)
freq: 5765
beacon interval: 100 TUs
capability: ESS Privacy RadioMeasure (0x1011)
signal: -25.00 dBm
last seen: 354 ms ago
Information elements from Probe Response frame:
SSID: NETGEAR78
Supported rates: 6.0* 9.0 12.0* 18.0 24.0* 36.0 48.0 54.0
RSN: * Version: 1
* Group cipher: CCMP
* Pairwise ciphers: CCMP
* Authentication suites: PSK
* Capabilities: 16-PTKSA-RC 1-GTKSA-RC (0x000c)
BSS Load:
* station count: 0
* channel utilisation: 0/255
* available admission capacity: 0 [*32us]
HT capabilities:
Capabilities: 0x9ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 7935 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 4 usec (0x05)
HT RX MCS rate indexes supported: 0-23
HT TX MCS rate indexes are undefined
HT operation:
* primary channel: 153
* secondary channel offset: below
* STA channel width: any
* RIFS: 1
* HT protection: no
* non-GF present: 0
* OBSS non-GF present: 0
* dual beacon: 0
* dual CTS protection: 0
* STBC beacon: 0
* L-SIG TXOP Prot: 0
* PCO active: 0
* PCO phase: 0
Extended capabilities:
* Extended Channel Switching
* BSS Transition
* Operating Mode Notification
* Max Number Of MSDUs In A-MSDU is unlimited
VHT capabilities:
VHT Capabilities (0x0f8259b2):
Max MPDU length: 11454
Supported Channel Width: neither 160 nor 80+80
RX LDPC
short GI (80 MHz)
TX STBC
SU Beamformer
SU Beamformee
VHT RX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT RX highest supported: 0 Mbps
VHT TX MCS set:
1 streams: MCS 0-9
2 streams: MCS 0-9
3 streams: MCS 0-9
4 streams: not supported
5 streams: not supported
6 streams: not supported
7 streams: not supported
8 streams: not supported
VHT TX highest supported: 0 Mbps
VHT operation:
* channel width: 1 (80 MHz)
* center freq segment 1: 155
* center freq segment 2: 0
* VHT basic MCS set: 0x0000
WPS: * Version: 1.0
* Wi-Fi Protected Setup State: 2 (Configured)
* Response Type: 3 (AP)
* UUID: daefb3b6-e5b1-95e3-b129-6eff7b6db709
* Manufacturer: NETGEAR, Inc.
* Model: R7000
* Model Number: R7000
* Serial Number: 32
* Primary Device Type: 6-0050f204-1
* Device name: R7000
* Config methods: Display
* RF Bands: 0x3
* Unknown TLV (0x1049, 6 bytes): 00 37 2a 00 01 20
WMM: * Parameter version 1
* u-APSD
* BE: CW 15-1023, AIFSN 3
* BK: CW 15-1023, AIFSN 7
* VI: CW 7-15, AIFSN 2, TXOP 6016 usec
* VO: CW 3-7, AIFSN 2, TXOP 3264 usec
# wpa_passphrase NETGEAR78 >> /etc/wpa_supplicant/wpa_supplicant.conf
xxxxxxxxxxxx
# wpa_supplicant -i wlp3s0 -c /etc/wpa_supplicant/wpa_supplicant.conf
Successfully initialized wpa_supplicant
nl80211: Could not set interface 'p2p-dev-wlp3s0' UP
nl80211: deinit ifname=p2p-dev-wlp3s0 disabled_11b_rates=0
p2p-dev-wlp3s0: Failed to initialize driver interface
P2P: Failed to enable P2P Device interface
wlp3s0: SME: Trying to authenticate with e4:f4:c6:14:f9:1f
(SSID='NETGEAR78' freq=5765 MHz) wlp3s0: Trying to associate with
e4:f4:c6:14:f9:1f (SSID='NETGEAR78' freq=5765 MHz) wlp3s0: Associated
with e4:f4:c6:14:f9:1f wlp3s0: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0
wlp3s0: WPA: Key negotiation completed with e4:f4:c6:14:f9:1f [PTK=CCMP
GTK=CCMP] wlp3s0: CTRL-EVENT-CONNECTED - Connection to
e4:f4:c6:14:f9:1f completed [id=0 id_str=] wlp3s0:
CTRL-EVENT-DISCONNECTED bssid=e4:f4:c6:14:f9:1f reason=3
locally_generated=1 nl80211: deinit ifname=wlp3s0 disabled_11b_rates=0
wlp3s0: CTRL-EVENT-TERMINATING ^C