Trouble Burning Core 5 CDs
by Bjorgen T. Eatinger
I am trying to create the 5 CDs necessary for a new Fedora Core 5 installation, and can never get a good burn. The media check always fails, during installation.
Once thing I noticed is that the ISO images appear to be a bit larger than 650MB, which is the recordable size of the CDs I am using. I will try 700MB CDs, but I wonder why the images would be distributed to be over 650MB, and if this is really the issue.
I tried burning the CDs using 3 different burners on 3 different workstations, with the same results. Is there a recommended media manufacturer? I am burning at the slowest speed (16x) possible as well.
I have never had so much trouble burning CDs before! In fact, this got so crazy, that I finally gave up and purchased a Fedora book on Core 2 which contained the CDs, and they worked perfect. But I am now running 3 versions behind. This has been an extremely frustrating experience, to say the least.
This is so much trouble, that I wish there was a company that produced and sold a commercial Fedora release on CDs.
Sincerely, Bjorgen T. Eatinger
17 years, 8 months
- 9
- 8
lspci unknown device
by SERGIE
Got Asus motherboard P5RD1-VM....
The problem is the first two strings indicating that the kernel is not
identifying the devices/chipsets. How to find the right
solution/driver/module, or at least understand what that is for...
++ 00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
++ 00:01.0 PCI bridge: ATI Technologies Inc Unknown device 5a3f
I tried contact ASuS, they said they supported windows only...
Google returns the same lspci results from other people and no solutions ((
=== lspci ===
00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
00:01.0 PCI bridge: ATI Technologies Inc Unknown device 5a3f
00:19.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge
00:1b.0 Ethernet controller: ALi Corporation M5263 Ethernet Controller (rev
50)
00:1c.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:1c.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
00:1d.0 Audio device: ALi Corporation High Definition Audio/AC'97 Host
Controller
00:1e.0 ISA bridge: ALi Corporation PCI to LPC Controller (rev 31)
00:1e.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
00:1f.0 IDE interface: ALi Corporation M5229 IDE (rev c7)
00:1f.1 RAID bus controller: ALi Corporation ULi 5287 SATA (rev 02)
01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress
200]
02:14.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
=== lspci ===
Below is
=== lspci -vv ===
00:00.0 Host bridge: ATI Technologies Inc Unknown device 5a33 (rev 01)
Subsystem: ASUSTeK Computer Inc. Unknown device 819a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
00:01.0 PCI bridge: ATI Technologies Inc Unknown device 5a3f (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000a000-0000cfff
Memory behind bridge: bfd00000-dfdfffff
Prefetchable memory behind bridge: 9fc00000-bfbfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [b0] #0d [0000]
00:19.0 PCI bridge: ALi Corporation M5249 HTT to PCI Bridge (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR+ <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: dfe00000-dfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR+ <PERR+
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [c0] HyperTransport: MSI Mapping
00:1b.0 Ethernet controller: ALi Corporation M5263 Ethernet Controller (rev
50)
Subsystem: ASUSTeK Computer Inc. Unknown device 816a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (5000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at dffffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (20000ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 185
Region 0: Memory at dfffc000 (32-bit, non-prefetchable) [size=4K]
00:1c.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (20000ns max), Cache Line Size 10
Interrupt: pin B routed to IRQ 209
Region 0: Memory at dfffd000 (32-bit, non-prefetchable) [size=4K]
00:1c.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) (prog-if
10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (20000ns max), Cache Line Size 10
Interrupt: pin C routed to IRQ 217
Region 0: Memory at dfffe000 (32-bit, non-prefetchable) [size=4K]
00:1c.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) (prog-if
20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (4000ns min, 8000ns max)
Interrupt: pin D routed to IRQ 193
Region 0: Memory at dffff800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1d.0 Audio device: ALi Corporation High Definition Audio/AC'97 Host
Controller
Subsystem: ASUSTeK Computer Inc. Unknown device 818f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 20000ns max)
Interrupt: pin C routed to IRQ 201
Region 0: Memory at dfff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 ISA bridge: ALi Corporation PCI to LPC Controller (rev 31)
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 6000ns max)
00:1e.1 Bridge: ALi Corporation M7101 Power Management Controller [PMU]
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
00:1f.0 IDE interface: ALi Corporation M5229 IDE (rev c7) (prog-if 8a [Master
SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 169
Region 4: I/O ports at ff00 [size=16]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.1 RAID bus controller: ALi Corporation ULi 5287 SATA (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8056
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 128, Cache Line Size 80
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at ec00 [size=16]
Region 1: I/O ports at e480 [size=8]
Region 2: I/O ports at e400 [size=16]
Region 3: I/O ports at e080 [size=8]
Region 4: I/O ports at e000 [size=32]
Region 5: Memory at dffff400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
01:05.0 VGA compatible controller: ATI Technologies Inc RC410 [Radeon Xpress
200] (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device 819a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 0
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at c0000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at dfde0000 [disabled] [size=128K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
02:14.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Compex FN22-3(A) LinxPRO Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 185
Region 0: I/O ports at d800 [size=256]
Region 1: Memory at dfeffc00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at dfee0000 [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
=== lspci -vv ===
17 years, 8 months
- 2
- 1
0000:00:00.0 kernel PCI
by SERGIE
You have probably have read this message, however thereis another bug which
arises on boot. It says to STDERR:
===
PCI: Cannot allocate resource region 3 of device 0000:00:00.0
===
This is my dmesg... On setting `quiet' parameter to the kernel a problem arise
on STDERR, which says (these strings somewhere below):
Please help if someone is able to...
=== dmesg ===
Linux version 2.6.17.11 (sg@sg) (gcc version 4.1.1 20060525 (Red Hat 4.1.1-1))
#54 Tue Sep 5 11:39:38 YEKST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001bfb0000 (usable)
BIOS-e820: 000000001bfb0000 - 000000001bfbe000 (ACPI data)
BIOS-e820: 000000001bfbe000 - 000000001bfe0000 (ACPI NVS)
BIOS-e820: 000000001bfe0000 - 000000001c000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
447MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 114608
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 110512 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x000fb1a0
ACPI: XSDT (v001 A M I OEMXSDT 0x04000611 MSFT 0x00000097) @ 0x1bfb0100
ACPI: FADT (v003 A M I OEMFACP 0x04000611 MSFT 0x00000097) @ 0x1bfb0290
ACPI: MADT (v001 A M I OEMAPIC 0x04000611 MSFT 0x00000097) @ 0x1bfb0390
ACPI: MCFG (v001 A M I OEMMCFG 0x04000611 MSFT 0x00000097) @ 0x1bfb0400
ACPI: OEMB (v001 A M I AMI_OEM 0x04000611 MSFT 0x00000097) @ 0x1bfbe040
ACPI: DSDT (v001 A0313 A0313001 0x00000001 INTL 0x02002026) @ 0x00000000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1c000000:e3780000)
Built 1 zonelists
Kernel command line: ro root=/dev/hda1 selinux=0 quiet video=vesafb vga=0x318
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2533.370 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 450200k/458432k available (1589k kernel code, 7616k reserved, 673k
data, 156k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5073.77 BogoMIPS
(lpj=10147540)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000
0000651d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000651d
00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: bfebfbff 20000000 00000000 00000180 0000651d
00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU: Intel(R) Celeron(R) CPU 2.53GHz stepping 09
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 0k freed
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 828k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-403f claimed by ali7101 ACPI
Boot video device is 0000:01:05.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2P._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15), disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15), disabled.
ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0401
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0F03
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: PnP ACPI: found 15 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 3 of device 0000:00:00.0
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:07' and the driver 'system'
pnp: match found with the PnP device '00:0a' and the driver 'system'
pnp: match found with the PnP device '00:0c' and the driver 'system'
pnp: 00:0c: ioport range 0xc00-0xc0f has been reserved
pnp: 00:0c: ioport range 0xd00-0xd0f has been reserved
pnp: 00:0c: ioport range 0xa20-0xa2f has been reserved
pnp: 00:0c: ioport range 0xa30-0xa3f has been reserved
pnp: match found with the PnP device '00:0d' and the driver 'system'
pnp: match found with the PnP device '00:0e' and the driver 'system'
PCI: Bridge: 0000:00:01.0
IO window: a000-cfff
MEM window: bfd00000-dfdfffff
PREFETCH window: 9fc00000-bfbfffff
PCI: Bridge: 0000:00:19.0
IO window: d000-dfff
MEM window: dfe00000-dfefffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:19.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1157477394.052:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
vesafb: framebuffer at 0xa0000000, mapped to 0xdc880000, using 4608k, total
65536k
vesafb: mode is 1024x768x24, linelength=3072, pages=27
vesafb: protected mode interface info at c000:552e
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
ACPI: Processor [CPU1] (supports 8 throttling states)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
pnp: the driver 'serial' has been registered
pnp: match found with the PnP device '00:0b' and the driver 'serial'
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:1f.0
ACPI: PCI Interrupt 0000:00:1f.0[A] -> GSI 21 (level, low) -> IRQ 169
ALI15X3: chipset revision 199
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST380011A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ASUS CD-S520B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
pnp: the driver 'ide' has been registered
hda: max request size: 512KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
hdc: ATAPI 52X CD-ROM drive, 96kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:08' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
pnp: match found with the PnP device '00:09' and the driver 'i8042 aux'
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
PCE2 PCE3 PCE4 PCE5 PCE6 PCE7 PE2P SLT1 SLT2 PS2K PS2M UAR1 LAN USB0 USB1
USB2 UB20 AC97 AZAL
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 156k freed
input: AT Translated Set 2 keyboard as /class/input/input0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Real Time Clock Driver v1.12ac
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Linux agpgart interface v0.101 (c) Dave Jones
uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 20 (level, low) -> IRQ 177
eth0: ULi M5263 at pci0000:00:1b.0, 00:15:f2:83:22:3d, irq 177.
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ali15x3_smbus 0000:00:1e.1: ALI15X3_smb region uninitialized - upgrade BIOS or
use force_addr=0xaddr
ali15x3_smbus 0000:00:1e.1: ALI15X3 not detected, module not inserted.
ali1535_smbus 0000:00:1e.1: ALI1535_smb region uninitialized - upgrade BIOS?
ali1535_smbus 0000:00:1e.1: ALI1535 not detected, module not inserted.
SCSI subsystem initialized
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:14.0[A] -> GSI 17 (level, low) -> IRQ 185
libata version 1.20 loaded.
eth1: RealTek RTL8139 at 0xd800, 00:80:48:37:af:27, IRQ 185
eth1: Identified 8139 chip type 'RTL-8100B/8139D'
sata_uli 0000:00:1f.1: version 0.5
PCI: Enabling device 0000:00:1f.1 (0105 -> 0107)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 21 (level, low) -> IRQ 169
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE482 bmdma 0xE000 irq 169
ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE082 bmdma 0xE008 irq 169
ata3: SATA max UDMA/133 cmd 0xEC08 ctl 0xE486 bmdma 0xE010 irq 169
ata4: SATA max UDMA/133 cmd 0xE408 ctl 0xE086 bmdma 0xE018 irq 169
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023
88:407f
ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_uli
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ata2: SATA link down (SStatus 0)
scsi1 : sata_uli
ata3: SATA link down (SStatus 0)
scsi2 : sata_uli
ata4: SATA link down (SStatus 0)
scsi3 : sata_uli
Vendor: ATA Model: ST3808110AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:1c.3: EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:1c.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1c.3: reset hcs_params 0x103398 dbg=1 cc=3 pcc=3 ports=8
ehci_hcd 0000:00:1c.3: reset portroute 0 0 1 1 1 0 2 2
ehci_hcd 0000:00:1c.3: reset hcc_params 7002 thresh 0 uframes 256/512/1024
ehci_hcd 0000:00:1c.3: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1c.3
ehci_hcd 0000:00:1c.3: ...powerdown ports...
ehci_hcd 0000:00:1c.3: supports USB remote wakeup
ehci_hcd 0000:00:1c.3: irq 193, io mem 0xdffff800
ehci_hcd 0000:00:1c.3: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
ehci_hcd 0000:00:1c.3: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:1c.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17.11 ehci_hcd
usb usb1: SerialNumber: 0000:00:1c.3
usb usb1: uevent
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: individual port power switching
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:1c.3: GetStatus port 2 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
ACPI: PCI Interrupt 0000:00:1d.0[C] -> GSI 22 (level, low) -> IRQ 201
0:0:0:0: Attached scsi generic sg0 type 0
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:1c.3: port 2 low speed --> companion
ehci_hcd 0000:00:1c.3: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 185
ohci_hcd 0000:00:1c.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:1c.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:1c.0: created debug files
ohci_hcd 0000:00:1c.0: irq 185, io mem 0xdfffc000
ohci_hcd 0000:00:1c.0: resetting from state 'reset', control = 0x0
ohci_hcd 0000:00:1c.0: OHCI controller state
ohci_hcd 0000:00:1c.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:1c.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:1c.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:1c.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:1c.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:1c.0: hcca frame #0003
ohci_hcd 0000:00:1c.0: roothub.a 01001203 POTPGT=1 NOCP NPS NDP=3(3)
ohci_hcd 0000:00:1c.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:1c.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:1c.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:1c.0: roothub.portstatus [1] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:1c.0: roothub.portstatus [2] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17.11 ohci_hcd
usb usb2: SerialNumber: 0000:00:1c.0
usb usb2: uevent
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: no over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:1c.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA
PPS CCS
hub 2-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 18 (level, low) -> IRQ 209
ohci_hcd 0000:00:1c.1: OHCI Host Controller
drivers/usb/core/inode.c: creating file '003'
ohci_hcd 0000:00:1c.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:1c.1: created debug files
ohci_hcd 0000:00:1c.1: irq 209, io mem 0xdfffd000
ohci_hcd 0000:00:1c.1: resetting from state 'reset', control = 0x0
ohci_hcd 0000:00:1c.1: enabling initreset quirk
ohci_hcd 0000:00:1c.1: OHCI controller state
ohci_hcd 0000:00:1c.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:1c.1: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:1c.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:1c.1: intrstatus 0x00000004 SF
ohci_hcd 0000:00:1c.1: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:1c.1: hcca frame #0003
ohci_hcd 0000:00:1c.1: roothub.a 01001203 POTPGT=1 NOCP NPS NDP=3(3)
ohci_hcd 0000:00:1c.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:1c.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:1c.1: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:1c.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:1c.1: roothub.portstatus [2] 0x00000100 PPS
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17.11 ohci_hcd
usb usb3: SerialNumber: 0000:00:1c.1
usb usb3: uevent
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: no over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 19 (level, low) -> IRQ 217
ohci_hcd 0000:00:1c.2: OHCI Host Controller
drivers/usb/core/inode.c: creating file '004'
ohci_hcd 0000:00:1c.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:1c.2: created debug files
ohci_hcd 0000:00:1c.2: irq 217, io mem 0xdfffe000
ohci_hcd 0000:00:1c.2: resetting from state 'reset', control = 0x0
ohci_hcd 0000:00:1c.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA
PPS PES CCS
ohci_hcd 0000:00:1c.2: enabling initreset quirk
ohci_hcd 0000:00:1c.2: OHCI controller state
ohci_hcd 0000:00:1c.2: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:1c.2: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:1c.2: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:1c.2: intrstatus 0x00000004 SF
ohci_hcd 0000:00:1c.2: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:1c.2: hcca frame #0003
ohci_hcd 0000:00:1c.2: roothub.a 01001203 POTPGT=1 NOCP NPS NDP=3(3)
ohci_hcd 0000:00:1c.2: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:1c.2: roothub.status 00008000 DRWE
ohci_hcd 0000:00:1c.2: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:1c.2: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:1c.2: roothub.portstatus [2] 0x00000100 PPS
usb usb4: default language 0x0409
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: OHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.17.11 ohci_hcd
usb usb4: SerialNumber: 0000:00:1c.2
usb usb4: uevent
usb usb4: configuration #1 chosen from 1 choice
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: uevent
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: no power switching (usb 1.0)
hub 4-0:1.0: no over-current protection
hub 4-0:1.0: power on to power good time: 2ms
hub 4-0:1.0: local power source is good
usb 2-2: new low speed USB device using ohci_hcd and address 2
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:1c.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA
PPS PES CCS
ohci_hcd 0000:00:1c.1: suspend root hub
usb 2-2: skipped 1 descriptor after interface
usb 2-2: default language 0x0409
usb 2-2: new device strings: Mfr=3, Product=1, SerialNumber=0
usb 2-2: Product: USB UPS
usb 2-2: Manufacturer: OMRON
usb 2-2: uevent
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
usb 2-2:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
hub 3-0:1.0: state 7 ports 3 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 3 chg 0000 evt 0004
hub 4-0:1.0: state 7 ports 3 chg 0000 evt 0000
Non-volatile memory driver v1.2
usbcore: registered new driver hiddev
usbhid 2-2:1.0: usb_probe_interface
usbhid 2-2:1.0: usb_probe_interface - got id
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
drivers/usb/core/file.c: looking for a minor, starting at 96
hiddev96: USB HID v1.11 Device [OMRON USB UPS] on usb-0000:00:1c.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ohci_hcd 0000:00:1c.2: suspend root hub
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel(a)redhat.com
EXT3 FS on hda1, internal journal
Adding 987956k swap on /dev/hda5. Priority:-1 extents:1 across:987956k
ip_tables: (C) 2000-2006 Netfilter Core Team
ip_conntrack version 2.4 (3581 buckets, 28648 max) - 224 bytes per conntrack
uli526x: eth0 NIC Link is Up 100 Mbps Full duplex
it87: Found IT8712F chip at 0xd00, revision 7
[drm] Initialized drm 1.0.1 20051102
17 years, 8 months
- 2
- 1
FC5 - Eclipse with Sun Java
by Mostafa Afgani
Hi,
I am trying to run Eclipse with the Sun jdk-1.5.0_08 but it fails to
start with the following error messege dialog:
JVM terminated. Exit code=1
/usr/bin/java
-jar startup.jar
-os linux
-ws gtk
-arch x86_64
-launcher /usr/bin/eclipse
-name Eclipse
-showsplash 600
-exitdata f0015
-vm /usr/bin/java
-vmargs
-jar startup.jar
I am using alternatives to manage the java symlink. When the
alternative is set to FC5 jre-1.4.2-gcj version of java, Eclipse
starts up just fine. Is there some configuration step that I have
missed?
TIA,
-M
17 years, 8 months
- 2
- 2
OT: Searching mail folders and subfolders in evolution
by Patrick Doyle
I know this is a bit off topic, but since evolution seems to be the
default mail client (for FC5, anyway), and since I figure there are
folks out there reading this list who know the answer, I figured it
couldn't hurt to ask...
Does anybody know how to search evolution folders and subfolders for
messages with particular text? I've tried the obvious solution of
selecting the "On this computer" top level folder, selecting "Message
Contains", entering the word for which I am looking, and clicking on
"Find Now". But I don't find any messages. If I navigate down to the
subfolder and repeat the experiment, I find what I'm looking for, but
I don't always know what subfolder contains the information for which
I'm looking.
I've gotten spoiled by Coppernic on WIndows, with it's integration
with Outlook. Should I be looking at beagle to do the same thing? Is
there a Gnome applet similar to the Coppernic applet for Windows?
--wpd
17 years, 8 months
- 2
- 1
Reading and applying patches
by Chong Yu Meng
Hi all,
I'm having some difficulty understanding patching in general. A little
background: I downloaded the source tarball for a program and it will
not "make" cleanly. Checking the forum on the website, someone had
published a patch in the form of text in an email that looks like this:
--- mlrate/mlrate.c 2003-01-27 10:31:31.000000000 +0100
+++ mlrate.new/mlrate.c 2004-11-22 12:37:52.086783325 +0100
@@ -25,6 +25,8 @@
#include <string.h>
... and continues for a bit longer
I assume that I should copy and paste the text into a separate file and
save it. But how do I apply the patch to the source file, which is
mlrate.c?
Also, how do I read the file? From some patch files I have come across,
they have "pluses" and "minuses" and other notation. What do they mean?
Can someone point me to some URLs where I can understand more about
these patch files?
Thanks in Advance!
--
Pascal Chong
email: chongym(a)cymulacrum.net
web: http://cymulacrum.net
pgp: http://cymulacrum.net/pgp/cymulacrum.asc
"La science ne connaît pas de frontière parce que la connaissance
appartient à l’humanité. et que c’est la flamme qui illumine le monde."
-- Louis Pasteur
17 years, 8 months
- 6
- 6
How to create /dev/dsp ?
by Timothy Murphy
I took a disk out of one computer, and put it in another
(more precisely, I took out the Utrabay hard disk from a ThinkPad T20
and put it in a ThinkPad T23)
and now I am told there is no sound because
"Device /dev/dsp does not exist".
How exactly does one ensure that this device is created?
There seems to be a rule in /etc/udev/rules.d/
KERNEL=="dsp*", MODE="0660"
I take it this just says that if /dev/dsp is created
it should have mode 0660?
I googled quite extensively for "fedora udev dsp"
and came across a large number of queries
and a few answers which I tried without success.
Several referred to "alsaconf" which does not seem to be available in FC-5.
I seem to have modules running which should create /dev/dsp ,
as shown by the partial lsmod list below.
I'd be very grateful for a solution to this conundrum:
how do I create /dev/dsp, and why has it not been created for me?
---------------------------------------
snd_emu10k1_synth 6464 0
snd_emux_synth 32032 1 snd_emu10k1_synth
snd_seq_virmidi 5120 1 snd_emux_synth
snd_seq_midi_emul 5888 1 snd_emux_synth
snd_emu10k1 114180 1 snd_emu10k1_synth
snd_rawmidi 18912 2 snd_seq_virmidi,snd_emu10k1
snd_ac97_codec 92032 1 snd_emu10k1
snd_ac97_bus 1792 1 snd_ac97_codec
snd_seq_oss 29888 0
snd_seq_midi_event 5888 2 snd_seq_virmidi,snd_seq_oss
snd_seq 45744 7
snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_oss,snd_seq_midi_event
snd_pcm_oss 34624 0
snd_mixer_oss 15424 1 snd_pcm_oss
snd_pcm 65640 3 snd_emu10k1,snd_ac97_codec,snd_pcm_oss
snd_seq_device 6348 6
snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_rawmidi,snd_seq_oss,snd_seq
snd_timer 18180 3 snd_emu10k1,snd_seq,snd_pcm
snd_page_alloc 7656 2 snd_emu10k1,snd_pcm
snd_util_mem 3328 2 snd_emux_synth,snd_emu10k1
snd_hwdep 6660 2 snd_emux_synth,snd_emu10k1
snd 42916 13
snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_seq_oss,snd_seq,snd_pcm_oss,snd_mixer_oss,snd_pc
---------------------------------------
Incidentally, is there any way of re-starting the sound system
apart from re-booting?
Why can one not say "system sound restart"?
--
Timothy Murphy
e-mail (<80k only): tim /at/ birdsnest.maths.tcd.ie
tel: +353-86-2336090, +353-1-2842366
s-mail: School of Mathematics, Trinity College, Dublin 2, Ireland
17 years, 8 months
- 3
- 5
wrong time stamp on files uploaded ??
by Gregory Machin
Hi..
I have a client with an ftp server on thier lan that is use by the bulk
scanner ...
when we upload files from a pc to the ftp server the time stamp is 2 hours
earlier than the current time on the pc used to up load it and when I
checked the date/time on the server it is the same as that on pc ??? where
is proftpd getting the 2 hour differenc ??
fc 4 server ..
Many Thanks
--
Gregory Machin
gregory.machin(a)gmail.com
www.linuxpro.co.za
17 years, 8 months
- 4
- 5
Disabling hardware detection
by Jacques B.
I know you can disable hardware detection, but can't find how to do
it. Once FC5 has properly booted up and recognized your existing
hardware (and hence the config files are ok) can you not disable
hardware detection to speed up booting? If so, how is that done in
FC5? I haven't added hardware in quite some time. And if I do, I can
simply re-enable it.
Thanks,
Jacques B.
17 years, 8 months
- 3
- 4
ATI 8.28.8 mplayer xv crash
by William John Murray
Hello all,
I have discovered that since updating ATI drivers (3 weeks
ago?)
mplayer always crashes my machine if the xv video out display is used.
In my xorg.conf I have a line in "device"
"VideoOverlay" "on"
If I comment it out I get no xv, and no crash.
This is with a Radeon Mobility 300 driver
kmod-fglrx-8.28.8-1.2.6.17_1.2174_FC5
and
xorg-x11-drv-fglrx-8.28.8-1.lvn5
It used to work, with older drivers.
Has anyone a solution to this?
Thanks,
Bill
17 years, 8 months
- 1
- 0